Professional Documents
Culture Documents
AquilionMulti Broucher
AquilionMulti Broucher
No. MPDCT0162EAD
Multislice HELICAL CT SCANNER
MULTI
APPLICATION
FEATURES
• High-speed scanning
This system permits simultaneous resolution of 2.5 mm at 0.25%, and The image of any slice thickness can
4-slice acquisition per 0.5 second high-contrast resolution of 0.35 mm. be generated later by reconstruction
rotation using the SSMD and pro- Multislice helical CT can be per- retry. For example, after the 2-mm
viding surpossed volumetric data formed using thin slices in routine slice thickness scanning is performed,
acquisition. The waiting time for examinations, so that high-precision, the images of several slice thicknesses
cooling of the X-ray tube is reduced, 3D and MPR images can be generat- can be generated from raw data such
because the exposure time is short. ed from the high-resolution voxel as a 10-mm thick image for routine
Therefore, patient waiting time and data. In CT angiography of the examinations, a 5-mm thick image
throughput is improved. brain, for example, a 40-mm for detail examination, and 2-mm
distance can be scanned in 5.5 thick image for generation of a 3D
• Wide range of slice thick- seconds at a slice thickness of 1 mm. volume.
nesses The use of “stack scan” with thin
The SSMD, which provides both slices minimizes partial volume • Multislice CT fluoroscopy
high-speed and high-resolution artifact. (option)
scanning, allows slice thicknesses Conventional CT fluoroscopic shows
of 0.5 mm, 1 mm, 2 mm, 3 mm, 4 • High patient throughput only a single slice, but multislice CT
mm, 5 mm, 8 mm, or 10 mm, to be In combination with fast scanning, permits realtime image reconstruction
selected, based on the objectives of the high-power 60-kW X-ray genera- to display 3 images obtained by com-
the examinations. tor and 7.5-MHU X-ray tube, bining 4 slices. Multislice CT
enable the data for routine examina- fluoroscopy significantly improves
• High quality image tions and the biopsy and 3D genera- operability in biopsy and interven-
The system achieves low-contrast tion to be acquired in 1 scan. tional procedures.
Product Data
No. MPDCT0162EAD
COMPOSITION
• Delay time setting: Time between the end of • Reconstruction method: MUSCOT Reconstruction
reproduction and scan start (MUltiSlice COne-beam
can be set up to 10 s in Tomography)
increments of 1 s. • The relation between the slice thickness and the
imaging area scanned in 5 s (0.5 s, 10 rotations) in the
Helical scan longitudinal direction are shown for helical pitches 3.0,
• X-ray tube rotation 4.5, and 6.0.
speed: 0.5, 0.75, 1, 1.5 s/360° Image slice Setting slice Helical pitch (Note)
• Maximum time of one thickness thickness 3.0 4.5 6.0
continuous scan: 100 s
• Scan start time delay: Min. 1 s 0.5 mm 0.5 mm 15.0 mm 22.5 mm 30.0mm
Setting is possible in steps of 1 mm 1 mm 30.0 mm 45.0 mm 60.0 mm
0.1 s. 2 mm 2 mm 60.0 mm 90.0 mm120.0 mm
• Scan field in axial 5 mm 5 mm 150.0 mm225.0 mm300.0 mm
direction: Max. 1390 mm/scan
Up to 10 scan plans are 10 mm 8 mm 240.0 mm360.0 mm480.0 mm
programmable in one eXam Note: The couchtop traveling distance per rotation is
Plan. (Multiple and/or shown in proportion to the slice thickness.
Multi-directional Helical)
• Couch speed: This can be specified Dynamic scan
arbitrarily within the range of • Scan time: 0.5, 0.75, 1, 1.5 s/360°
2.5 mm to 96 mm/s. (in • Programmable time: Max. 1 hour
steps of 0.1 mm/s) • Number of
• Helical scan pitch 2.5/3/3.5/4.5/5/5.5/6 programmable scans: Max. 100 scans
• Image reconstruction • Maximum time of one
time: Min. 1.2 s continuous scan: 100 s
• Real time Helical • Scan plan
reconstruction time: 0.13 s/image – Scan interval: Min. interval is 1 s.
(1 slice/512 × 512 matrix) Setting is possible in steps of
0.08 s/image 0.1 s in scan interval more
(1 slice/256 × 256 matrix) than 1 s.
• SureStart Note: When a scanning mode with patient couch
– Max continuous movement is used, the minimum scan interval
scan time: 100 s is limited by the time for movement.
– Region of interest – Scan plan
(ROI): Max. 3 ROIs programming: Up to 360 different
– CT number Sequences can be pre-
measurement interval: 0.125 s programmed.
– Scan start time delay: Min. 3 s • Scan start time delay: Min. 0.5 s
– Display function: CT number lapse time Setting is possible in steps of
• Specification of 0.1 s.
reconstruction position: By entering the couchtop • Maximum scan rate: Max. 200 scans/100 s
position, or on the (0.5 s scan, 200 rotations)
scanogram (in minimum • Image reconstruction
units of 0.1 mm) – Full image: 1 image/360°
• Reconstruction Mode: Full image – Half image: 1 image/229°
Half image • Partial image: Reconstruction is possible in
Detail image steps of 0.1 s.
4
Multislice HELICAL CT SCANNER
MULTI
5
Product Data
No. MPDCT0162EAD
Data storage – Enlargement (2×, 4× for L and LL size; 8×, 16× for
• Magnetic disk LL size)
– Raw data: max. 4,000 rotations • CT image processing
(0.5 s scan) – ROI setting and processing
– Image data: max. 16,000 · ROI shape: Point, rectangular, polygonal,
• Magnetooptical disk: Approximately 9,600 images elliptical, irregular
or 600 rotations raw data per · ROI processing: Mean value, standard devia-
cassette (2.6 Gbyte) tion, area, number of pixels
· ROI display: 3 ROIs can be displayed on
Image display an image
• Display monitor: 21-inch color × 2 units · ROI control: Size, position, rotation
• Monitor matrix: 1280 × 1024 – Measurement of distance and angle between two
• Image matrix: 1024 × 1024 (max.) points
• CT number – Profile (oblique profile also available)
display range: From −1,024 to +8,191 – Histogram
• Window width: Continuously variable – CT number display
(adjustable at variable speed) – Mark display (grid display, scale display)
• Window level: Continuously variable – Volume calculation
(adjustable at variable speed) – Enlargement (2×, 4× and arbitrary size)
• Preset window: 3 kinds of window settings – Addition/subtraction between images
may be preset for each image. – Band display (non-linear windowing)
• Window types: Linear, non-linear (6 user- – Comment and arrow insertion
programmable), and double – Top/bottom, right/left, black/white reversal of
windows. image
• Image retrieval – Image filtering
– Method: On-screen menus and – Screen save
keyboard – High speed axial interpolation
– Mode: Image, series and patient – MultiView (Auto MPR)
• Autoview function: Software control, • Raw data processing
function key – Multi-zooming (processing of raw data for 4 ROIs
• Multi-frame display: Reduction/cut-off display, and multiple images)
ROI processing – Stack reconstruction
• Inset scanogram display – Protect/Unprotect
• Selective related information display – Play/Reverse reconstruction
• Cine display • System management
– Number of frames: Up to 128 – Warm-up
– Image display speed: The display speed can be – Calibration data
varied up to a maximum of – Picture retouching
20 frames/s. – Scanogram/CT image switching
6
Multislice HELICAL CT SCANNER
MULTI
8
Multislice HELICAL CT SCANNER
MULTI
OUTLINE DRAWING
960
(37.8)
380 580
(15) (22.8)
30° 30°
(TILT ANGLE)
(76.8)
1,950
2,057
(81)
1,016
(40)
2,330
(91.7)
Gantry
(18.5)
(24.4)
470
620
1,820 2,000
(71.7) (78.7)
Couchtop stroke
1,490 2,390
(58.7) (94.1)
(25.7)
655
Stroke
(41.1)
300 (37.5)
1045
955
(15.4)
390
(11.8)
Patient Couch
Unit: mm (in)
11
Product Data Multislice HELICAL CT SCANNER
No. MPDCT0162EAD
MULTI
OUTLINE DRAWING
1,600 800
(31.5)
(63.0)
(49.8)
1,265
(31.5)
800
(27.6)
700
Navibox
1,010 420
(39.8) (16.5)
Unit: mm (in)
Console
Note: Console desk is not included as standard. The photograph of the system on the cover differs from the drawing above.
TOSHIBA CORPORATION
MEDICAL SYSTEMS COMPANY
http://www3.toshiba.co.jp/medical
©Toshiba Corporation 1999 all rights reserved. Toshiba Corporation Medical Systems Company
meets internationally recognized standards
Design and specifications subject to change without notice. for Quality Management System Toshiba Nasu Operations meets the Environmental
ISO 9001, ISO 13485, EN 46001. Management System standard, ISO 14001.
2001-10 TME/SB
Printed in Japan