Professional Documents
Culture Documents
QB EE6201 Circuit Theory R2013
QB EE6201 Circuit Theory R2013
com
Unit-I
PART-A
www.Vidyarthiplus.com
www.Vidyarthiplus.com
The region surrounding a voltage source which connects the two nodes directly is called
super node.
9. What is principle node?
The meeting point of three or more elements is called principle node.
10. State voltage division rule.
Voltage across a resistor in a series circuit is equal to the total voltage across the series
elements multiplies by the value of that resistor divided by the total resistance of the series
elements.
11. State current division rule.
The current in any branch is equal to the ratio of the opposite parallel branch resistance to
the total resistance value, multiplies by the total current in the circuit.
12. Give the steps to draw a Dual Network
In each loop of a network place a node
Draw the lines connecting adjacent nodes passing through each element and also to the
reference node. 13. Compare series and parallel circuit.
S.No. Series circuit Parallel circuit
1 The total effective resistance is the sum The reciprocal of the total effective
of the individual resistance ie resistance is the sum of the reciprocals of
Reff=R1+R2+……R n individual resistance
1/Reff= 1/R1+1/R2+….1/R n
2 Only one path for the current flow More than one path for the current to flow
3 The current flowing through all the The current flowing through each
resistances will be the same and equal to resistance is different
the total current
4 The voltage is divided across each The voltage across each resistance is
resistance according to the value of same which will be equal to the input
resistance. voltage.
14. What are the classifications of Circuit elements?
Active element
Passive element
Lumped and distributed elements
Bilateral and unilateral elements
Linear and non linear elements.
15. What is a planar circuit?
A circuit is said to be non planar if it cannot be drawn on a plane surface without
crossovers.
PART-B
www.Vidyarthiplus.com
www.Vidyarthiplus.com
1.
2.
3. i)Using the node voltage analysis, find all the node voltages and currents in 1/3 ohm and 1/5
ohm resistances of figure.
ii) For the mesh-current analysis, explain the rules for constructing mesh impedance matrix and
solving the matrix equation [Z]I = V.
4.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
5.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
Unit-II
PART-A
www.Vidyarthiplus.com
www.Vidyarthiplus.com
PART-B
1.(i) Find the value of R and the current flowing through it in the circuit shown when the
current in the branch OA is zero. (8)
2. Derive expressions for star connected arms in terms of delta connected arms and delta
connected arms in terms of star connected arms. (16)
www.Vidyarthiplus.com
www.Vidyarthiplus.com
3.
5.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
www.Vidyarthiplus.com
www.Vidyarthiplus.com
Unit-III
www.Vidyarthiplus.com
www.Vidyarthiplus.com
PART-B
1.
2.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
3.
4.
5. A step voltage V(t) = 100 u(t) is applied to a series RLC circuit with L=10H, R=2ohm
and C= 5F. The initial current in the circuit is zero but there is an initial voltage of
50V on the capacitor in a direction which opposes the applied source. Find the
expression for the current in the circuit.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
UNIT IV
9.
10.W
rite down the condition, for the response of RLC series circuit to be under damped and
overdamped for step input.
The response of RLC series circuit with step input in
www.Vidyarthiplus.com
www.Vidyarthiplus.com
11. Write down the few applications of RL, RC, RLC circuits.
Coupling circuits
Phase shift circuits
Filters
Resonant circuits
AC bridge circuits
Transformers
12.
13.
14.
PART-B
1.
2.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
3.
4.
5.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
UNIT-V
www.Vidyarthiplus.com
www.Vidyarthiplus.com
PART-A
6.
7.
8.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
14.
15.
PART-B
1.
2. (i) Three impedances Z1 = 3∟45° ohm, Z2 = 10 √2∟45° ohm, Z3 = 5 ∟-90° ohm are connected
in series. Calculate applied voltage if voltage across Z1 = 27∟-10° V. (8)
(ii) A delta connected load as shown in figure is connected across 3 phase 100 volt supply. Determine
all line currents. (8)
3.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
4.
5.
www.Vidyarthiplus.com