Professional Documents
Culture Documents
Granor Elastomeric Laminated Bearings
Granor Elastomeric Laminated Bearings
Granor Elastomeric Laminated Bearings
GRANOR®
ELASTOMERIC
LAMINATED
BEARINGS
ELASTOMERIC LAMINATED BEARINGS
UNIQUE BEARING
ID NUMBER
REFERENCED
ON TEST REPORT
PRODUCT
FEATURES
SUPPLIED BY UNDER COMPRESSION
GRANOR FOR
MORE THAN
40 YEARS
Frees up support conditions
r
allowing movement
INSTALLATION B + 70mm
A + 70 mm
life it is always good design prac- 3MPa then the friction gener- high quality cementitious grout
tice to detail installation in a way ated by wood float finish mortar or epoxy mortar and should be
that facilitates possible removal pads is considered sufficient to of at least 40MPa compressive
for inspection / replacement of the prevent the bearings from grad- strength. Mortar pads should
bearings. ually “walking” out of position be as flat and level as possible.
under light load. If the mini- Thick mortar pads may require
Options for installation vary greatly
mum load case stress is less reinforcing.
depending on the material for con-
than 3MPa then steel retainer
A
tact surfaces, i.e. concrete, steel, Bearings can be supplied with
r
plates with flat keeper bars are
or a combination of both. blind holes if necessary for
recommended. However always
mechanical restraint with steel
The following basic design guide- consult with relevant state au-
“stub” dowels. Note however that
lines should be considered: thority for preferred details in
the use of steel stub dowels
the applicable region. Steel plate
r Flatness of contact surfaces to achieve positive retention Keeper Bars
should be within +/- 1mm over r Note that it is recommended that makes removal of the bearings Typically 32mm x 10mm Typically 16mm thick
the required area. Where there adhesives, including epoxies, more difficult and is therefore to Retained with M10 GR.8.8 bolts
is any out of parallelism due not be used to restrain bearings be discouraged unless required
to construction tolerances this from “walking” out of position for project specific reasons (for
should be considered in the under light load. The reason for example some seismic designs).
context of the total available this is that if the adhesive should
rotation capacity of the bearing. fail then the resulting surface will
typically have a very smooth low
The texture of the contact sur-
r friction surface which may be
face should be kept at a high worse than if no adhesive had
coefficient of friction. Where been used.
concrete mortar pads are used
specify a rough “wood float” fin- r Edge clearance – support area
ish. Where steel retainer plates should always be larger than
are used bolted on flat keeper the ELB. A distance of approx.
bars should be specified around 25mm around the bearing
the perimeter of the bearing. should be adopted as minimum.
SPECIFICATIONS
330mm
Ø40mm
600mm
10mm
600mm
300mm ± 1mm
10mm
180mm
12mm
5mm
6mm
40mm
23mm
60mm
SPECIFICATIONS
RECTANGULAR SERIES A – D AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
SPECIFICATIONS
RECTANGULAR SERIES E – G AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
SPECIFICATIONS
RECTANGULAR SERIES H – K AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
SPECIFICATIONS
CIRCULAR SERIES N – R AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
SPECIFICATIONS
CIRCULAR SERIES S – U AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
SPECIFICATIONS
CIRCULAR SERIES V – Y AS5100.4 – 2004
GRANOR Overall height Calculated Compressive Mean shear Calculated Shear deflection Rated load at ZERO rotation Rated load at MAX rotation AS Mass
Part number mm stiffness at zero shear stiffness kN/mm rotational stiffness capacity mm Part No. kg
At max. shear At zero shear At max. shear At zero shear
kN/mm kNm/rad
kN kN kN kN
GRANOR.COM.AU
GRANOR RUBBER & ENGINEERING
8 REID STREET,
BAYSWATER, VICTORIA 3153
AUSTRALIA
EMAIL. INFO@GRANOR.COM.AU
TELEPHONE. +61 3 9762 9699
GRANOR.COM.AU