Professional Documents
Culture Documents
Installation Guide: 3.lock Connection
Installation Guide: 3.lock Connection
Lock Connection
Installation Guide (1) Share power with the lock:
Version: 1.0 Date: June, 2012 + +
+12V +12V
- GND
- GND
FR 107
Fixing Hole Fixing Hole
-
+
NO1 - NO1 and the device is equal or less
Instruction for the Mounting Paper
11
+ - NC1
NO LOCK NC1
12 NO2 NO2
13
14
COM2 COM2
Fixing Hole Fixing Hole
15
16
(1) Paste the mounting template on the (2) Remove the screw on the (3) Take away the back plate. (2) Does not share power with the lock:
wall. Drill the holes according to bottom of device.
the marks on the template (holes
+
for screws and wiring). +12V + +12V
DC12V - GND
- GND Does not shares power with the lock:
BELL- DC12V
A. ULOCK=12V I-ILOCK≤1A;
+ BELL-
BELL+ -
BELL+
+ SEN - FR 107
SEN
B. ULOCK≠12V;
+
GND GND C. The distance between the lock and
NO LOCK
DC Power
- BUT
-
BUT
the device is more than 10 meters.
NO1 NO1
- COM1 COM1
+
NC1 + NC1
FR 107 NO2
+ - NO2
COM2 COM2
NC LOCK DC Power
(4) Fix the rubber pad and the back (5) Place the unit onto the mounting bracket,
plate on the wall according to and tighten the screw at the bottom of the unit. (1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at
the mounting paper. power on) is connected with ‘NO’ and ‘COM’ terminals, and the NC LOCK(normally close at power
on) is connected with ‘NC’and ‘COM’ terminals.
(2) When the Electrical Lock is connected to the Access control System, you need to connect one FR107
2. Structure and Function diode (shipped in the package) in parallel with the connection to prevent the self-inductance EMF
feedback the system. NB: Do not reverse the polarities!
Access Control System Function
RS485 TCP/IP (1) If a registered user verified, the device will send a signal
⑦ to unlock the door.
RS232/RS485 Converter ⑤ 4. Other Connections 5. Power Connection
(2) The door sensor will detect the ON-OFF state. If the door
Exit
④ is unexpectedly opened or improperly closed, the alarm signal +Power- BELL- The device working voltage DC 12V, electric current
①
Lock Sensor ② ⑥ Exit Button
(digital value) will be triggered. Door Bell
% BELL+
SEN 500mA (50mA standby). Positive is connected with
GND ‘+12V’, negative is connected with ’GND’.
(3) If the device is illegally removed , the device will signal the alarm. Exit BUT (Do not reverse the polarities)
% Exit Button NO1
COM1
4
1
5
2 3
6
C
(7) Supports RS485, TCP/IP communication to be able to connect with Alarm Voltage output ≤ DC 12V
③
PC. One PC can manage multiple devices. ①:‘I’: device output current, ‘ULOCK’: lock voltage,‘ILOCK’: lock current
Alarm
4
2
5
3
6
C
DATA1 +12V 7 8
0
9
M/OK
Power + Red
WD1 GND
GND GND Power- Black
GND DATA1 Communications of PC:
IWD1
RXD DATA0 Access Control Device Reader
IWD0 Please use specified RS485 wire, RS485 active
TXD RLED
RLED converter and bus-type wiring. 485+
GND GLED 485-
Access Control Panel GLED 485+ 485-
485+ BEEP Terminals:
485- BEEP
Terminals PC Serial Ports
RS485 Bus
(1) Do not exceed 90m(meters) distance between the Device and Access Control Lock OR Card reader. 485+ RS485+ 485+ 485- 485+ 485-
(In case of long distance installation, use the Wiegand Signal Extender to minimise interference).
485- RS485- 1
4
2
5
3
6
C 1
4
2
5
3
6
C
(2) To keep a balanced and stable Wiegand signal, connect the device, access control lock and card reader 7 8
0
9
M/OK
7 8
0
9
M/OK
RS485
on the same ‘GND’ (ground) port. Converter
2. TCP/IP Mode:
About the terminals definition, please refers Terminals Wire Name Color
to the right table. RJ45-1 TX+ White-orange
8.Other Functions RJ45-2 TX- Orange
Two ways for TCP/IP connection: RJ45-3 RX+ White-green
7
2
8
3
9
C 1
7
2
8
3
9
C
0 M/OK 0 M/OK
device number, system password, IP address, RS485 address, etc. IP Address:192.168.1.201 IP Address:192.168.1.124
The user data won't be cleared. Subnet Mask:255.255.255.0 Subnet Mask:255.255.255.0
(6) Do not change the cable type in case of a long distance installations.