Professional Documents
Culture Documents
PF753 QuickConfig Analog Setup Reduced
PF753 QuickConfig Analog Setup Reduced
PF753 QuickConfig Analog Setup Reduced
www.WernerMN.com 1.800.POWER01
PowerFlex 753 Quick-Configuration – Analog Setup
LIMITS
P520 Max Fwd Speed NP Hz / NP RPM and 0 Hz P27 [Motor NP Hz] 60Hz or 1800RPM Typically
Voltage / NP RPM x 16 0 RPM P28 [Motor NP RPM]
P521 Max Rev Speed NP Hz x 16.00 / 0.00 0 Hz P27 [Mtr NP Hz]* (-1) 0 if not reversing
NP RPM x – 16.00 / 0.00 0 RPM P28 [Mtr NP RPM]*(-1)
P522 Min Fwd Speed 0.0 / NP Hz x 16.00 0 Hz 0.00 Hz
0.00 / NP RPM x 16.00 0 RPM 0.00 RPM
P523 Min Rev Speed 1.0 / NP Hz x -16.00 0 Hz 0.00 Hz
0.00 / NP RPM x -16.00 0 RPM 0.00 RPM
P524 Overspeed Limit 10 Hz Only need to adjust if the Max
Freq (P.037) is less than 70.
P535 Accel Time 1 0.00 – 3600 Secs 0.00 Secs 10.0 Secs
P537 Decel Time 1 0.00 – 3600 Secs 0.00 Secs 10.0 Secs
P545 Spd Ref A Sel 546 - 260 871 - Port 1 Reference Port 0 PF753, Param 871 Example: PF753 Port 0, 260-
876 - Port 6 Reference - Port 1 Reference AnalogIn0 Value
260 – Analog In0 Value
OTHER PARAMETERS
P348 Auto Rstrt Tries 0/9 0–9 0
P349 Auto Rstrt Delay 0.5/30.0 Secs 1.0
P356 Flying Start Mode 0 – Disabled, 1 – Enhanced, Use Sweep when a Sine Wave
2 – Sweep Filter is installed on VFD Output.
P621 Slip RPM at FLA (P27 [Motor NP Hz] x RPM 20 Set to 0 in most cases. Not used
120)/(P31 [Motor Poles – in closed Vector control.
P28 [Motor NP RPM])
DYNAMIC BRAKE PARAMETERS – (IF USED)
P372 Bus Regulator Mode 0 – Disabled 1 – Adjust Freq Need an external snubber resistor
1 – Adjust Freq if set to Dyn Brake or “Both”.
2 – Dyn Brake
3 – Both DB 1st
4 – Both Frq 1st
P426 Regen Power Limit 0—800% % -50% Set to -800% when P372 set to
Dyn Brake
P382 DB Resistor Type 0/1 0 – Internal, 1 – External 0 - Internal Typically an external resistor is
used
P383 DB External Resistance Based on Drive Ohms Based on Drive
P384 DB External Watts 1.00/500000.0 Watts 100.0
P385 DB Ext. Pulse Watts 1.00/1000000.0 Watt 2000.0 Set to value of the external
resistor.
Note: The PowerFlex 753 is Port 0. If an I/O card is used in slots 4, 5 or 6 the I/O will start with the slot the I/O card is.
For example, if using a I/O point one on the I/O card in Slot 5 to run the drive, the I/O point is mapped to DI Run as
“Port 5: Dig In Sts. Input 1”
www.WernerMN.com 1.800.POWER01
PowerFlex 753 Quick-Configuration
www.WernerMN.com 1.800.POWER01
PowerFlex 753 Quick-Configuration
Literature
Programming Manual: 750-PM001
Installation Guide: 750-IN001
Technical Data: 750-TD001
Knowledgebase: rockwellautomation.custhelp.com
www.WernerMN.com
December 2013
1.800.POWER01