Professional Documents
Culture Documents
DSI Cat 2020 HQ
DSI Cat 2020 HQ
DSI Cat 2020 HQ
2020/2021
www.dsisrael.com
Valid from 1 of January 2020 until publication of new catalog.
Handling of products:
For handling, indications and contraindications please refer
to the respective procedures manuals at dsisrael.com or visit
our dedicated website for all our instructions for use at:
https://dsisrael.com/about-dsi/downloads/downloads
Note: In order to improve readability, DSI Ltd. does not use ™
or ® in the running text. By doing so, however, DSI Ltd. does
not waive any right to the trademark or registered mark and
nothing herein shall be construed to the contrary.
Disclaimer: Some products may not be regulatory cleared/
released for sale in all markets. Please contact the local dealer
or send e-mail to info@dsisrael.com for current product
assortment and availability.
Company Profile
On the overcrowded Israeli dental market DSI brand was born. Right
after the start, DSI set a new standard for quality and value in the
dental consumables market.
Introduction 1
Table of Contents 2
Implant Analysis 4
Implants 6
Internal Hex Connection
Prosthetic parts 21
Implants 18
Conical Connection
Prosthetic parts 86
Instruments 116
Biomaterials 182
Cementation 198
Essentials 201
Endodontics 206
Prophylaxis 225
Laboratory 228
Clean Implant
In the implantology, our mission stays the same – to provide the Superior Raw
top level products at affordable prices. DSI Implant line meets
the highest standards of the dental industry. With the years of Material
experience in the market, DSI thrives to perfection in both quality DSI Dental Implants:
assurance and customer services.
• Made of biocompatible alloy
Ti6Al-4V ELI.
We believe in easy-to-use implant systems and products, that still • Pure titanium with Superior
provide the solutions even for the sophisticated cases. While being mechanical properties.
friendly to the new users, DSI implant systems offer a full prosthetic • Raw materials imported by
solution for the most demanding and experienced dental professionals. leading American suppliers.
Our unique way is to combine an extensive knowledge base with
creative engineering.
Most of DSI Implant products are made from the Titanium alloy Ti6Al4V
(Grade 5).
This alloy is also known as Eli Grade 23 Titanium. ELI is short for
"Extra Low Interstitials" that provide more ductility and better
fracture toughness. The favorable combination of properties such
as low specific weight, high strength to weight ratio, high modulus
of elasticity, very high corrosion resistance and excellent general
biocompatibility, makes it an ideal choice for the fabrication of dental
superstructures and implants.
Melting Range 0
C ± 15 0C 1649
Co-Efficient of
0-100 0C 8.6 X 10-6
Thermal Expansion
Tensile Strength MPA 1000
Hardness ROCKWELL C 36
Clean Surfaces
DSI unique and improved multi-stage
cleaning process gently removes residues
left from manufacturing, leaving the
surface free of contamination.
Ti Ti Spectrum
SLA Advantages
• SURVIVAL RATES
High and consistent survival
rates (over 95% after a five-year
follow-up).
• BONE PRESERVATION
Average bone loss of <1 mm
V after five years (based on the
Al implant loading time).
V
• NO PERI-IMPLANTITIS
Very low prevalence of peri-
0 2 4 6 8 implantitis over the 5-year
follow-up period.
Full Scale 475 cts Cursor: 0.000 keV
Length
Platform switching preserve the crestal bone height and
soft tissue levels, increasing the quality outcomes in the
treatments.
6.0 mm SPI 0638 SPI 0642 SPI 0650 SPI 0660 Hex 2.43±0.01
8.0 mm SPI 0835 SPI 0838 SPI 0842 SPI 0850 SPI 0860
10.0 mm SPI 1035 SPI 1038 SPI 1042 SPI 1050 SPI 1060
11.5 mm SPI 1135 SPI 1138 SPI 1142 SPI 1150 SPI 1160
13.0 mm SPI 1335 SPI 1338 SPI 1342 SPI 1350 SPI 1360
Implant Ø 3.0
Ø 2.0 Ø 2.5
Implant Ø 3.5
Implant Ø 3.75
Implant Ø 4.2
Implant Ø 5.0
Implant Ø 6.0
Implant Ø 3.0
Implant Ø 3.5
Implant Ø 3.75
Implant Ø 4.2
Implant Ø 5.0
Implant Ø 6.0
Length
placement procedures.
8.0 mm DFI 0835 DFI 0838 DFI 0842 DFI 0850 DFI 0860
10.0 mm DFI 1035 DFI 1038 DFI 1042 DFI 1050 DFI 1060
Hex 2.43±0.01
11.5 mm DFI 1135 DFI 1138 DFI 1142 DFI 1150 DFI 1160
13.0 mm DFI 1335 DFI 1338 DFI 1342 DFI 1350 DFI 1360
Drilling Protocol
Pilot Drill
Implant Ø 3.5
Implant Ø 3.75
Implant Ø 4.2
Implant Ø 5.0
Implant Ø 6.0
Length
Length Ø 3.5 Ø 3.75 Ø 4.2 Ø 5.0 Ø 6.0
SBI 0835 SBI 0838 SBI 0842 SBI 0850 SBI 0860
10.0 mm SBI 1035 SBI 1038 SBI 1042 SBI 1050 SBI 1060
Hex 2.43±0.01
11.5 mm SBI 1135 SBI 1138 SBI 1142 SBI 1150 SBI 1160
13.0 mm SBI 1335 SBI 1338 SBI 1342 SBI 1350 SBI 1360
Drilling Protocol
Pilot Drill
Implant Ø 3.5
Implant Ø 3.75
Implant Ø 4.2
Implant Ø 5.0
Implant Ø 6.0
Length
Internal Hex Connection 2.0 mm.
Length Ø 3.0
Pilot Drill
Implant Ø 3.0
Ø Diameter
SLA Surface
Treatment
Smart Implant
The design of the implant was derived from the different
qualities of the bone at its cortical and spongiosal parts. While
the cortical bone provides us with a stable grip, it also suffers
from limited blood supply and high probability of necrosis due
Length
to over-pressure. The spongiosal bone, on the other hand, is
softer, but compressible and has high blood supply with stem
cells which contribute to the healing process.
The correlation between the implant's shape and the bone
type to which it enters, results in an equal distribution of load
forces along the entire length of the implant, and an increased
primary stability of the implant.
13.0 mm SMI 1338 SMI 1342 SMI 1345 Scan the QR-code
for drilling protocol
explanatory video.
Drilling Protocol
Recommended
Bone Bone
speed 850 RPM
type D1 type D1
9 mm
otherwise handled with larger two-piece implants.
• The DSI Monoblock has been shown to be stronger when
loaded to failure than most industry standard under-4-mm
diameter implants.
• Those implants can be placed using a single-stage
protocol, while soft-tissue experiences much less trauma.
• Implant body receives same SLA surface treatment as other
DSI implants.
Length
Length Ø 2.8 Ø 3.0 Ø 3.3 Ø 4.2
6.0 mm MC 0642
8.0 mm MC 0842
Drilling Protocol
Pilot Drill
Implant Ø 2.8
Ø 2.0 Ø 2.5
Implant Ø 3.0
Ø 2.0 Ø 2.5 Ø 2.8
Implant Ø 3.3
SEM of both surfaces at x2000 magnification. RBM surface – left image and SLA surface – right image.
RBM plays the main role in roughened implant surfaces and provides increased retention strength. The topography,
down to the micrometer, affects the attachment and the growth of new bone cells, more rapidly and more stable at the
same time.
The material used for the RBM process is Calcium Phosphate. This is a highly resorbable and biocompatible material.
Usage of Calcium Phosphate as a blasting material eliminates the need for using strong acids for the removal of blasting
material remnants.
Such surface technology gives excellent results, reaching the optimal osseointegration and complete healing process
with almost zero chance of abruption. Even the particles that are left are fully biocompatible, promote earlier bone in-
growth and provide greater implant stability during the first critical weeks after placement.
DSI RBM Premium Line has a spiral thread design with twin
cutting grooves and redirecting ability. The coronal micro-
treads designed to increase bone-implant contact and RBM
provide long-term crestal area stability. Recommended for Surface
Treatment
two-stage surgical procedures, but suitable for the single-
stage placement as well.
• Surface roughness value of about Ra 2.5 to 3.0 µm.
• Consistent surface micro pits between 1 to 3 µm.
• Surface area is increased by 46 percent compared to SLA
Length
treated implants.
Clinical Advantages:
• Easy Insertion.
• Osteoconductivity.
• Self-Tapping.
• High Implant Stability.
• Allows placement of the implant into small diameter
osteotomes.
10.0 mm SRI 1030 SRI 1035 SRI 1038 SRI 1042 SRI 1050
Hex 2.0 ± 0.02
11.5 mm SRI 1130 SRI 1135 SRI 1138 SRI 1142 SRI 1150
13.0 mm SRI 1330 SRI 1335 SRI 1338 SRI 1342 SRI 1350
6.5 mm
compressive threads. It is used for multiple unit restorations with
immediate loading in the upper and lower jaws with adequate RBM
bone tissue. It can be used in combination with basal implants Surface
Treatment
and allows flap and flapless placement. Abutment direction can
be adjusted up to 17° relative to the implant axis.
4.07 mm
Ø D2
• Special compressive threads.
• Immediate loading.
• Adjustable abutment slope angle.
Clinical Advantages:
• Simple placement & prosthetic procedure.
• Adjustable abutment slope angle.
• Bone condensation design.
• No pumping effect.
Length
Length Ø 3.3 Ø 3.75 Ø 4.2 Ø 5.0
Ø 1.5 Ø 2.0 Ø 2.8 Implant Ø 4.2 Ø 1.5 Ø 2.0 Ø 2.8 Ø 3.2 Implant Ø 4.2
Ø 1.5 Ø 2.0 Ø 2.8 Ø 3.2 Implant Ø 5.0 Ø 1.5 Ø 2.0 Ø 2.8 Ø 3.2 Ø 3.65 Implant Ø 5.0
Ø 1.5 Ø 2.0 Ø 2.8 Ø 3.2 Ø 3.65 Ø 4.2 Implant Ø 6.0 Ø 1.5 Ø 2.0 Ø 2.8 Ø 3.2 Ø 3.65 Ø 4.2 Ø 4.5 Implant Ø 6.0
Length
bone stress and bone resorption and increase BIC.
• The surface roughness and Micro-morphology is a result
of sandblasting and acid etching. This proven surface
technology provides excellent osseointegration resulting
in long-lasting clinical success.
• Fully compatible with Nobel Active Implant RP and NP.
• Self-Drilling and self-tapping.
Platform NP RP
Hex 2.67 ± 0.01
Length Ø 3.5 Ø 4.3 Ø 5.0
6.0 mm SCI0650
Pilot Drill
Implant Ø 3.5 NP
Ø 2.0 Ø 2.8
Implant Ø 4.3 RP
Implant Ø 5.0 RP
Implant Ø 3.5 NP
Implant Ø 4.3 RP
Countersink
Ø 2.0 Ø 2.8 Ø 3.2 Ø 3.65
Ø 3.75x4.2
Implant Ø 5.0 RP
Features:
• Made of high quality surgical materials with a dark gray DNT²
coating, with outstanding corrosion resistance and exceptional
durability.
• Minimal heat generated by drill / bone, low vibration, controlled and
accurate operation with confidence
• Universal sizes compatible with most implant sizes on the market.
Special length markers that remain visible even in the most severe
conditions.
Premium Implant SLA Standard Healing Cap Transfer Open / Closed Tray
Regular Platform Regular Platform Regular Platform Analog Regular Platform
Blue Spiral Implant Standard Smooth Transfer with Clip Wide-body Analog
Regular Platform Regular Platform Regular Platform Regular Platform
Titanium Base Castable Abutment Titanium Abutment Overdenture Abutment Premium Multi-Unit
Narrow Platform 2.0 Narrow Platform 2.0 Narrow Platform 2.0 Narrow Platform 2.0 Narrow Platform 2.0
PEEK Scan Body Temporary Abutment Titanium Abutment Loc-In Abutment Next-Gen Multi-Unit
Regular Platform Regular Platform Regular Platform Regular Platform Regular Platform
CAD/CAM Titanium Base PEEK Abutment Aesthetic Abutment DSI-Lock Abutment Transfer and Analog for
Regular Platform Regular Platform Regular Platform Regular Platform Next-Gen MUA
Loc-In Housing
Ball Housing
Multi-Unit CAD/CAM Castable Titanium Abutment
Titanium Base Anatomic Abutment Angulated 35°/ 45° Premium Multi-Unit
Regular Platform Regular Platform Regular Platform DSI-Lock Housing Regular Platform
Ti-Bases for Implant Castable Abutment UCLA Anatomic Concave Transfer and Analog for
Systems Titanium Base Abutment Retention Inserts Premium MUA
DSI Analog
The analog is made of stainless steel and is
Height,
used in the preparation of laboratory models. Analog Type
mm
Ø mm Code
Material: Stainless Steel (Grade 316).
Analog
Narrow 12 mm Ø 3.0 mm SIA 300
Ø Diameter
Platform 2.0
Regular
Analog
12 mm Ø 3.75 mm SIA 375
Standard
Platform
Height
Short-body
Analog 9 mm Ø 3.75 mm SIA-US
Loc-in
Abutment 10 mm Ø 3.75 mm LOC-AN
Analog
Ball
Attachment 15 mm Ø 3.75 mm SBA370
Analog
DSI-Lock
14 mm Ø 4.4 mm EQ-AN
Analog
One-piece
implant 19 mm Ø 3.75 mm IAD375
Analog
Wide-body
Analog
12 mm Ø 5.0 mm SIA 500
Standard
Platform
Analog
for 3D 12 mm Ø 4.5 mm SIA-3D
printing
Next-Gen
Multi-Unit 12 mm Ø 5.0 mm MU-S-AN
Analog
Transfer
Transfers are designed for impressions Height,
using open-tray and closed-tray technique Transfer Type Ø mm Code
mm
Click transfer made without a screw and
has a hexagonal lock to ensure a tight
fit. Especially effective at molars and Transfer for
premolars zone. Narrow 13 mm Ø 3.8 mm STN38
Platform 2.0
Material: Stainless Steel (Grade 316).
Transfer
10 mm Ø 4.75 mm STS
Closed Tray
Transfer
A clip-on connection transfer for 13 mm Ø 4.75 mm ST13
Open Tray
impressions without a screw has a
hexagonal lock to ensure a tight fit. It
is especially effective with molars and
premolars, where there is a lack of space, Clip
and where working with a driver is difficult. Transfer for 9 mm Ø 4.5 mm STC9
It is sufficient to use this transfer for all Close Tray
types of impressions as the lack of screws
saves significant amount of time.
Clip
Transfer for 13 mm Ø 4.5 mm STC13
Close Tray
Clip
Transfer for 15 mm Ø 4.5 mm TMIS15
Close Tray
Transfer for
Premium 9 mm Ø 4.75 mm STFMU-K
MUA
Ø Diameter
Cap Height, mm Cuff Height Ø mm Code
8 mm
Straight Snap-On Transfer Anatomic Abutment Small
6 mm
Collar
4 mm Abutment Height, mm Code
Height, mm
Collar Height
Ø Diameter
Collar Height
Collar Height
Collar Height
Ø 4.8 mm
Collar Height
Ø 4.8 mm
Ø 4.5 mm
Ø 3.0 mm
Ø 5.5 mm
12.0 mm 5.5 mm STWA12
Ø Diameter
9.0 mm 1.0 mm 4.8 mm STSA01
Height
9.0 mm 3.8 mm STA9SM
Ø 3.8 mm
Collar Height
Ø 4.8 mm
25°
Height
Ø 4.8 mm
Ø 4.8 mm
15°
11.0 mm 3.0 mm 4.8 mm STAA15-3
Height
Ø 4.8 mm
Height, Collar
Abutment Ø mm Code
mm Height, mm
25°
mm Height, mm
Ø 4.8 mm
Hex
9.5 mm 3.5 mm NACH
(Narrow 2.0)
Rotational
9.5 mm 3.5 mm NACN
(Narrow 2.0)
Height
(Plastic)
9.5 mm 4.0 mm SACH
Hex
Ø 4.0 mm
(Plastic)
9.5 mm 4.0 mm SACN
Rotational
Hex
11.0 mm 4.3 mm NAMH
(Narrow 2.0)
Rotational
11.0 mm 4.3 mm NAMN
(Narrow 2.0)
Ø 4.3 mm
Recommendation: Hand-tighten using a 1.25 mm hex. driver or a motor mount with a force of 15 Ncm.
Material: Titanium (Ti6Al4V ELI).
Ø 4.5 mm
4.5 mm 4.5 mm PCT4
15°
Ø 4.8 mm
Ø 4.8 mm
11.0 mm 3.0 mm 4.8 mm SAAC25-3
Ø 4.5 mm
ScanPost Body
Scan
Material Height Code
Abutment
Ti-Base AB-type
Gingival
Abutment Type Ø mm Code
Height
Ø Diameter
Hex
0.5 mm 3.75 TB-U3
Narrow 2.0
Height 1
2.0 mm 3.0 mm GAMU-1720
Height 1
Healing Titanium
Cap screw
Crown
DSI Implants
* premounted on
angulated abutment.
Titanium Sleeve
12.0 mm 9.0 mm Ø 5.0 mm MU-S-TS
Abutment
Castable Sleeve
12.0 mm 9.0 mm Ø 5.0 mm MU-S-SP
Abutment
17°
Premium Multi-Unit Abutment Angulated 17° Narrow 2.0
Multi-Unit Height 1 Height 2 Code
Height 1
2.0 mm 3.5 mm MU-A17-NP-20
Height 1
17°
Premium Multi-Unit Abutment Angulated 17° Regular
Multi-Unit Height 1 Height 2 Code
Height 1
30°
Premium Multi-Unit Abutment Angulated 30° Regular
Multi-Unit Height 1 Height 2 Code
Height 2
45°
Adhesive
Castable Temporary Copings
Plastic Sleeve Titanium Sleeve
Healing Titanium
Cap screw
Crown
* premounted on
angulated abutment.
1.0 mm PMU-S-NP-10
2.0 mm PMU-S-NP-20
3.0 mm PMU-S-NP-30
4.0 mm PMU-S-NP-40
1.0 mm PMU-S-RP-10
2.0 mm PMU-S-RP-20
3.0 mm PMU-S-RP-30
4.0 mm PMU-S-RP-40
Titanium Sleeve
12.0 mm 9.0 mm Ø 5.0 mm SSTFMU-K
Abutment
Castable Sleeve
12.0 mm 9.0 mm Ø 5.0 mm SSPFMU-K
Abutment
Height 1
1.0 mm PLI-SP10
2.0 mm PLI-SP20
3.0 mm PLI-SP30
4.0 mm PLI-SP40
5.0 mm PLI-SP50
6.0 mm PLI-SP60
0.5 mm PLI-RP05
1.0 mm PLI-RP10
2.0 mm PLI-RP20
3.0 mm PLI-RP30
4.0 mm PLI-RP40
Regular Platform for Implant 3.5-6.0
Narrow Platform for Implant 3.0 5.0 mm PLI-RP50
6.0 mm PLI-RP60
Lab Cap
(is available on Black 0 kg CN090 CN100
request)
Metal Housing
Silver Ø 5.6 mm MH-LOCW
(height 2.0 mm)
Ø 14.0 mm/
Protective Disc Pink PD
internal Ø 2.9 mm
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring.
7.5 mm DFL
Ø 3.75 10 mm LOC-AN
K-Bar Attachment
K-Bar Collar Height Ø mm Code
Ø 4.2 mm
18°
Height 1
0.5 mm PDSL-RP05
1.0 mm PDSL-RP10
2.0 mm PDSL-RP20
3.0 mm PDSL-RP30
4.0 mm PDSL-RP40
5.0 mm PDSL-RP50
6.0 mm PDSL-RP60
Lab Cap
(is available on Black 0 kg RCL-LB
request)
Metal Housing
Silver Ø 4.5 mm MH-LOC
(height 2.0 mm)
Ø 14.0 mm/
Protective Disc Clear DP
internal Ø 1.6 mm
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring.
485IC
Ø 2.5 mm
0.5 mm 3.35 mm SBA05S
Collar Height
Ø Diameter
Ø 2.5 mm
0.5 mm 4.2 mm SBA05
Collar Height
Ø Diameter
0.5 mm PSBA05S
1.0 mm PSBA10S
2.0 mm PSBA20S
3.0 mm PSBA30S
4.0 mm PSBA40S
5.0 mm PSBA50S
6.0 mm PSBA60S
7.0 mm PSBA70S
0.5 mm PSBA05
1.0 mm PSBA10
2.0 mm PSBA20
3.0 mm PSBA30
4.0 mm PSBA40
5.0 mm PSBA50
6.0 mm PSBA60
7.0 mm PSBA70
1.0 mm PABAT-1810
2.0 mm PABAT-1820
3.0 mm PABAT-1830
1.0 mm PABAT-3010
2.0 mm PABAT-3020
3.0 mm PABAT-3030
1.0 mm PABAT-4010
2.0 mm PABAT-4020
3.0 mm PABAT-4030
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring and fixation screw.
1.0 mm BABAT-1810
2.0 mm BABAT-1820
3.0 mm BABAT-1830
1.0 mm BABAT-3010
2.0 mm BABAT-3020
3.0 mm BABAT-3030
1.0 mm BABAT-4010
2.0 mm BABAT-4020
3.0 mm BABAT-4030
Comes as a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, silicone insert, housing and fixation screw.
Lab Cap
(is available on Black 0 kg CN027
request)
Metal Housing
Silver Ø 4.6 mm MH-BAT
(height 3.2 mm)
Ø 14.0 mm/
Protective Disc Clear DP
internal Ø 1.6 mm
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring.
485IC
Loc-In & K-Bar Insertion Caps and Parts Ball Attachment Insertion Caps and Parts
Loc-In & K-Bar
CN089 Green Castable Sphere,
Violet Strong Cap RH83-BC009
Size Ø2.5 mm
Loc-In & K-Bar
CN086
Clear Standard Cap Silver Cap 0.35kg,
Loc-In & K-Bar Elastic and gummy, CN050
CN087 Normal Size Ø2.5 mm
Pink Soft Cap
Height 1
TAP-NB-
10.0 mm 1.5 mm
NP1515M
15°
TAP-NB-
12.0 mm 3.0 mm
NP1530M
Height
Collar Height
TAP-NB-
10.0 mm 1.5 mm
NP2515M
TAP-NB-
12.0 mm 3.0 mm
NP2530M
Height 1
TAP-NB-
10.0 mm 1.5 mm
RP1515M
25° TAP-NB-
12.0 mm 3.0 mm
RP1530M
Height
TAP-NB-
10.0 mm 1.5 mm
RP2515M
TAP-NB-
12.0 mm 3.0 mm
RP2530M
Ø Diameter
5.0 mm 3.8 mm HCC-5-NP
Height
Ø Diameter
9.0 mm 4.0 mm SSAC-9RP
Ø 4.0 mm
Conical Connection Straight Shoulder Abutment RP
Abutment Height 1 Height 2 Ø mm Code
Ø 3.8 mm
TA-NB-
10.0 mm 1.5 mm 5.0 mm
NP1515
TA-NB-
11.5 mm 3.0 mm 5.0 mm
NP1530
15°
TA-NB-
13.0 mm 4.5 mm 5.0 mm
NP1545
Height 1
Collar Height
TA-NB-
Ø 5.0 mm 10.0 mm 1.5 mm 5.0 mm
RP1515
TA-NB-
11.5 mm 3.0 mm 5.0 mm
RP1530
TA-NB-
13.0 mm 4.5 mm 5.0 mm
RP1545
Ø 3.8 mm
TA-NB-
10.0 mm 1.5 mm 5.0 mm
NP2515
TA-NB-
11.5 mm 3.0 mm 5.0 mm
NP2530
25°
TA-NB-
13.0 mm 4.5 mm 5.0 mm
NP2545
Height 1
Collar Height
Ø Diameter TA-NB-
10.0 mm 1.5 mm 5.0 mm
RP2515
TA-NB-
11.5 mm 3.0 mm 5.0 mm
RP2530
TA-NB-
13.0 mm 4.5 mm 5.0 mm
RP2545
Ø Diameter
11.0 mm 3.0 mm SPAA15-3-NB-NP
15°
Angulated Abutment Peek Anatomic 15° RP
Collar
Abutment Height, mm Code
Height, mm
Height 1
Ø Diameter
Collar Height
MUA-NB-
1.0 mm 2.5 mm
NP1710
17°
MUA-NB-
2.0 mm 3.5 mm
NP1720
Height 2
Height 1
MUA-NB-
1.0 mm 3.5 mm
NP3010
MUA-NB-
2.0 mm 4.5 mm
NP3020
Collar Height
MUA-NB-
1.0 mm 2.5 mm
RP1710
30°
MUA-NB-
2.0 mm 3.5 mm
RP1720
Height 2
Height 1
MUA-NB-
1.0 mm 3.5 mm
RP3010
MUA-NB-
2.0 mm 4.5 mm
RP3020
1.5 mm PMUA-NB-NP15
2.5 mm PMUA-NB-NP25
3.5 mm PMUA-NB-NP35
4.5 mm PMUA-NB-NP45
1.5 mm PMUA-NB-RP15
2.5 mm PMUA-NB-RP25
3.5 mm PMUA-NB-RP35
4.5 mm PMUA-NB-RP45
Titanium Sleeve
12.0 mm 9.0 mm Ø 5.0 mm SSTFMU-K
Abutment
preinstalled in
Fixation Long Screws 6.7 mm 5.1 mm Ø 1.85 mm
abutment
Collar Height
2.0 mm 4.0 mm LOC-NB-NP20
LOC-NB-
1.0 mm 2.0 mm
NP1810
LOC-NB-
18° 2.0 mm 3.0 mm
NP1820
LOC-NB-
3.0 mm 4.0 mm
Height 2
NP1830
Height 1
LOC-NB-
1.0 mm 2.0 mm
NP3010
LOC-NB-
2.0 mm 3.0 mm
NP3020
LOC-NB-
3.0 mm 4.0 mm
NP3030
Collar Height
2.0 mm 4.0 mm LOC-NB-RP20
1.0 mm PLOC-NB-NP10
2.0 mm PLOC-NB-NP20
3.0 mm PLOC-NB-NP30
4.0 mm PLOC-NB-NP40
5.0 mm PLOC-NB-NP50
1.0 mm PLOC-NB-RP10
2.0 mm PLOC-NB-RP20
3.0 mm PLOC-NB-RP30
4.0 mm PLOC-NB-RP40
5.0 mm PLOC-NB-RP50
Lab Cap
(is available on Black 0 kg CN090 CN100
request)
Metal Housing
Silver Ø 5.6 mm MH-LOCW
(height 2.0 mm)
Ø 14.0 mm/
Protective Disc Pink PD
internal Ø 2.9 mm
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring.
7.5 mm DFL
Ø 3.75 10 mm LOC-AN
Collar Height
2.0 mm 3.8 mm BAC-2-NP
BAC-3-RP
Collar Height
3.0 mm 3.8 mm
1.0 mm PBAC-1-NP
2.0 mm PBAC-2-NP
3.0 mm PBAC-3-NP
4.0 mm PBAC-4-NP
5.0 mm PBAC-5-NP
6.0 mm PBAC-6-NP
1.0 mm PBAC-1-RP
2.0 mm PBAC-2-RP
3.0 mm PBAC-3-RP
4.0 mm PBAC-4-RP
5.0 mm PBAC-5-RP
6.0 mm PBAC-6-RP
Lab Cap
(is available on Black 0 kg CN027
request)
Metal Housing
Silver Ø 5.0 mm MH-BAT
(height 3.2 mm)
Ø 14.0 mm/
Protective Disc Clear DP
internal Ø 1.6 mm
The kit is a ready-to-use solution including all the pieces that can be required during the procedure:
Abutment, 4 retention inserts, housing and isolation ring.
Ø 3.75 mm 15 mm SBA370
485IC
10.0 mm RDS2010
15.0 mm RDS2015
7.0 mm RDK24070
10.0 mm RDK24100
15.0 mm RDK24150
7.0 mm RDK125070
10.0 mm RDK125100
15.0 mm RDK125150
Ratchet Driver
18.0 mm RDOP
One-piece Implant
60.0 mm XL125600
20.0 mm MM12520
28.0 mm MM12528
20.0 mm MM2020
28.0 mm MM2028
20.0 mm MM24220
28.0 mm MM24028
7.0 mm HDK125070
10.0 mm HDK125100
15.0 mm HDK125150
25.0 mm HDK125250
2.42 HD
6.35 RHD
10.0 mm RDKC-NP10
15.0 mm RDKC-NP15
10.0 mm RDKC-RP10
15.0 mm RDKC-RP15
22.0 mm MMIC-NP22
28.0 mm MMIC-NP28
22.0 mm MMIC-RP22
28.0 mm MMIC-RP28
10.0 mm SPP100
16.0 mm SPP160
All DSI prosthetic 1.25 drivers are compatible with both Internal Hex and Conical Platforms.
23.5 mm
30.0 mm
Ratchet Wrench
Product Hex Code
6.35 mm SR
Allows an accurate appliance of the Recommended torque when using prosthetic or surgical drivers.
100.0 mm TSP01
Tissue Punch Ø 4 mm
Handle Length, mm Work length, mm Code
11.0 mm HW
6.0
8.0 4.0
10.0 3.0
11.5 2.0
13.0 1.0
16.0
Product Code
A B A+B Insert the manual centering device (A) into the implant and
using the claw reamer bur (B), following with great care
the instruction, in 90% of cases, the broken screw can be
removed easily. However if the broken screw is frozen in
place, the reverse cutting bur (C) must be used, by consuming
the broken screw. The operation should be performed with
attention, patience and competence. The time occurred may
be depend on many factor, among which the implant position
that can simplify or complicate the operation. Once the screw
is completely consumed, the shavings can be removed with
air or water.
Product Code
6 mm
Tool With Threaded Pin And
5 mm
Ball Indicator
4 mm
3 mm
1 mm
Lance Drill
Type Diameter Ø, mm Code
1.2 mm LD120
1.5 mm LD150
Marking Drill
Type Diameter Ø, mm Code
1.9 mm PD190
Drill Extender
Type Length, mm Code
29.0 mm TDE
2.0 mm PD200
2.5 mm TD250
2.8 mm TD280
3.2 mm TD320
3.65 mm TD365
4.0 mm TD400
4.2 mm TD420
4.5 mm TD450
5.2 mm TD520
2.0 mm DNP200
2.5 mm DNT250
2.8 mm DNT280
3.2 mm DNT320
3.65 mm DNT365
4.0 mm DNT400
4.5 mm DNT450
5.2 mm DNT520
Countersink Drills
Type Ø D1-D2, mm Code
3.75-4.2 mm CD375
5.0-6.0 mm CD500
Trephine Drills
Type Ø D1-D2, mm Code
2.0-3.0 mm TB200
3.0-4.0 mm TB300
4.0-5.0 mm TB400
5.0-6.0 mm TB500
3.0 mm TP30
4.0 mm TP40
4.5 mm TP45
5.0 mm TP50
38.0 mm / Ø 3 mm ICB-2
NEW
Ø D 4.3 mm
Optimal Irrigation Built-in Stopper
Supply
6.0 mm GD200L6
8.0 mm GD200L8
10.0 mm GD200L10
11.5 mm GD200L115
13.0 mm GD200L13
6.0 mm GD280L6
8.0 mm GD280L8
10.0 mm GD280L10
11.5 mm GD280L115
13.0 mm GD280L13
6.0 mm GD320L6
8.0 mm GD320L8
10.0 mm GD320L10
11.5 mm GD320L115
13.0 mm GD320L13
6.0 mm GD365L6
8.0 mm GD365L8
10.0 mm GD365L10
11.5 mm GD365L115
13.0 mm GD365L13
Product Code
6.0 mm PD200L6SC
8.0 mm PD200L8SC
10.0 mm PD200L10SC
11.5 mm PD200L115SC
13.0 mm PD200L13SC
6.0 mm TD280L6SC
8.0 mm TD280L8SC
10.0 mm TD280L10SC
11.5 mm TD280L115SC
13.0 mm TD280L13SC
6.0 mm TD320L6SC
8.0 mm TD320L8SC
10.0 mm TD320L10SC
11.5 mm TD320L115SC
13.0 mm TD320L13SC
6.0 mm TD365L6SC
8.0 mm TD365L8SC
10.0 mm TD365L10SC
11.5 mm TD365L115SC
13.0 mm TD365L13SC
6.0 mm TD400L6SC
8.0 mm TD400L8SC
10.0 mm TD400L10SC
11.5 mm TD400L115SC
13.0 mm TD400L13SC
6.0 mm TD450L6SC
8.0 mm TD450L8SC
10.0 mm TD450L10SC
11.5 mm TD450L115SC
13.0 mm TD450L13SC
Product Code
6.0 mm PD200L6S
8.0 mm PD200L8S
10.0 mm PD200L10S
11.5 mm PD200L115S
13.0 mm PD200L13S
6.0 mm TD280L6S
8.0 mm TD280L8S
10.0 mm TD280L10S
11.5 mm TD280L115S
13.0 mm TD280L13S
6.0 mm TD320L6S
8.0 mm TD320L8S
10.0 mm TD320L10S
11.5 mm TD320L115S
13.0 mm TD320L13S
6.0 mm TD365L6S
8.0 mm TD365L8S
10.0 mm TD365L10S
11.5 mm TD365L115S
13.0 mm TD365L13S
6.0 mm TD400L6S
8.0 mm TD400L8S
10.0 mm TD400L10S
11.5 mm TD400L115S
13.0 mm TD400L13S
6.0 mm TD450L6S
8.0 mm TD450L8S
10.0 mm TD450L10S
11.5 mm TD450L115S
13.0 mm TD450L13S
Product Code
Product Code
Ratchet Driver
Hex 2.0 / L 10.0 mm RDS2010
for Implant 3.0
Ratchet Driver
Hex 2.0 / L 15.0 mm RDS2015
for Implant 3.0
Removable
stainless
surgical tray
Tool kit includes special plastic polymer box and removable stainless surgical tray autoclavable in a temperature of 134° C.
Product Code
Tool kit includes special plastic polymer box and removable stainless surgical tray autoclavable in a temperature of 134° C.
Universal
Ratchet Driver
Drill
Extender
Abutment
Hand Driver
Countersink
Ratchet Drills (optional)
Drivers Inserts
Countersink Drills
Ø 3.75-4.2 mm CD375
(optional)
Countersink Drills
Ø 5.0-6.0 mm CD500
(optional)
6.0
8.0 4.0
10.0 3.0
11.5 2.0
13.0 1.0
16.0
Product Code
Product Size, Ø mm
Bur 1.0 mm
Bur 2.5 mm
Bur 3.0 mm
Bur 3.5 mm
Cleaning brush
Suction tube
Product Code
Stoppers
Type Length, mm Code
7.0 mm STP7
8.0 mm STP8
8.5 mm STP85
9.0 mm STP9
10.0 mm STP10
11.0 mm STP11
11.5 mm STP115
12.0 mm STP12
13.0 mm STP13
Ø 3.5 mm 1TD3516
Ø 3.8 mm 1TD3816
Ø 4.0 mm 1TD4016
Ø 4.2 mm 1TD4216
Ø 4.5 mm 1TD4516
Ø 4.8 mm 1TD4816
H 3.5 mm GD3248
10/ 11.5 / 13 / 15 / 16 mm BR
Opener in OPI
Bone Pusher
Type Info Code
Pincette
Type Info Code
Product Code
This is the tool to take out the broken screw by turning in reverse way.
This is the tool to take out the broken screw by turning in reverse way.
HRW9785 HHSA40
Product Code
Stoppers
Type Product Size, mm Code
Sinus curette
Type Size, mm Code
170.0 mm HNCR-1
160.0 mm HNCR-2
155.0 mm HNCR-3
160.0 mm HNCR-4
138.0 mm DG0246
Product Code
C-Stopper L-Stopper
Type Size, mm Code Type Size, mm Code
4.0 mm SDST-04
1.0 mm LAST-10
5.0 mm SDST-05
1.5 mm LAST-15
6.0 mm SDST-06
2.0 mm LAST-20
7.0 mm SDST-07
Guide drill
Type Size, mm Code
Ø2.0 mm SD-GD20
SD-Reamer
Type Size, mm Code
Ø2.8 mm SDR-28
Ø3.3 mm SDR-33
Ø3.7 mm SDR-37
Sinus curette
Type Product Code
Yellow TOLA2-01
Red TOLA2-02
Blue TOLA2-03
SDWRH-00
MP-BP
Silicone Tube
Product Code
Guide drill
Type Size, mm Code
Ø2.0 mm GD-20
Diamond Reamer
Type Size, mm Code
Ø2.0 mm TOCA-DR20
Ø2.8 mm TOCA-DR28
Ø3.3 mm TOCA-DR33
Stopper
Type Size, mm Code Type Size, mm Code
SD-Reamer
Type Size, mm Code
Ø2.3 mm SD-RM23
Ø2.8 mm SD-RM28
Ø3.3 mm SD-RM33
Ø3.7 mm SD-RM37
Bone packer
Type Size, mm Code
Ø2.0 mm GAG-08
Ø2.0 mm TOCA-SG
Bone Syringe
Type Size, mm Code
Ø2.5 mm BS-01
Product Code
SD-Reamer
Type Size, mm Code
Ø2.3 mm SD-RM23
Ø2.8 mm SD-RM28
Ø3.3 mm SD-RM33
Ø3.7 mm SD-RM37
CLS30
H.P CON
CLS35
R.C EXT
Guide drill
Type Size, mm Code
Ø2.0 mm GD-20
Product Code
Stop drill
Type Size, mm Code
Ø2.0 mm SD-20
Ø2.5 mm SD-25
Ø3.3 mm SD-33
Stopper
Type Size, mm Code Type Size, mm Code
14.0 mm SST-14
Product Code
Stopper
Type Size, mm Code Type Size, mm Code
1.5 mm LAST-1.5
Ø5.0 mm / 29 mm LASC-50
Ø7.0 mm / 29 mm LASC-70
Ø8.0 mm / 25 mm LASD-R80
Ø8.0 mm / 25 mm LASD-F80
Ø6.0 mm / 25 mm LASR-60
Ø8.0 mm / 25 mm LASR-80
Ø6.0 mm / 25 mm LACD-60
Ø8.0 mm / 25 mm LACD-80
Sinus curette
Type Product Code
Yellow TOLA2-01
Red TOLA2-02
Blue TOLA2-03
Green TOLA2-04
2.0 mm S-20
2.5 mm S-25
3.0 mm S-30
3.5 mm S-35
4.0 mm S-40
2.0 mm R-20
2.5 mm R-25
3.0 mm R-30
3.5 mm R-35
4.0 mm R-40
Osteotome Stopper
Type Size, mm Code Type Size, mm Code
8.0 mm OST-8
Instruments
Bone surgery
Product Code
Ridge Splitter
Product Type Size Code
4 mm / 1.0 mm SCL-01
4 mm / 1.5 mm SCL-02
4 mm / 2.0 mm SCL-03
4 mm / 2.5 mm SCL-04
4 mm / 1.0 mm SCL-05
Curved
Surgical Chisel
Used for shaping and removing bone. Autoclavable dental chisel instrument used for bone reshaping. It has semi-circular
notches that are beveled on each side of the sharp tip. The chisel can also be used to reflect flaps or for removing
secondary palatal flaps.
5.0 mm CO 1
5.0 mm CO 2
5.0 mm CO 3
Universal
Product Code
Expander drill
Type Size Code
Ø 1.8/2.5 / 14 mm SDEXP-01
Ø 2.0/3.0 / 14 mm SDEXP-02
Ø 2.5/3.5 / 14 mm SDEXP-03
Ø 2.8/4.0 / 14 mm SDEXP-04
Ø 3.0/4.5 / 14 mm SDEXP-05
Saw Disk
Type Size Code
Guide drill
Type Size Code
Ø 2.0 SDGDL-02
Contouring bur
Type Size Code
Ø 5.0 CT-50
4 mm / 1.0 mm SCL-05
SDWRH-00
Product Code
SDWRH-00
Product Code
Marking initial hole Use expander drill in sequential way Place implant.
witch initial drill. for smooth and even expansion.
Ø 1.8/2.5 / 14 mm SDEXP-01
Ø 2.0/3.0 / 14 mm SDEXP-02
Ø 2.5/3.5 / 14 mm SDEXP-03
Ø 2.8/4.0 / 14 mm SDEXP-04
Ø 3.0/4.5 / 14 mm SDEXP-05
Wrench SDWRH-00
Product Code
Engage NLBC to engine and apply When one of stoppers is completely merged, the total depth is 4 mm.
stopper.
Recommended RPM: 300. Recommended N/cm: 50. Collect bone inside the stopper, then
use the bone pusher to get it out.
GBR Tools
Type Product Code
Product Code
Product Code
GBR Mallet
Type Product Code
Mallet MT-414
17 mm
14 mm
16 mm
The improved DSI Mini Surgery Motor, designed and manufactured in Italy, Specification:
combine ease of use and practicality with top torque performance, full safety • Torque: Max 80 Ncm (32:1),
and operating precision with any implant system. 70 Ncm (20:1).
• Speed: 400-40000 rpm (1:1).
• Insulation: Class I, Type BF.
Content: • Peristaltic pump Max
• Control unit with a Irrigation: 90 ml/min.
peristaltic pump. • Settable Programs: 10.
• Brushless autoclavable DSI
Mini Motor LED.
• Multifunction foot-control
with variable speed.
• Two sterile irrigation tubes.
• Handpiece (20:1 Reduction)
Optic.
• Newest generation
brushless motor with
more power.
• Precise speed adjustment
up to 40000 rpm.
• Differential Torque up to
80Ncm.
• Extended service life
of parts that require
autoclave sterilization:
motor, cable and
connector.
Coross
Coross – the ideal alternative to bovine and human-derived products.
The COROSS biomimetic bone graft made from the mineral
exoskeleton of corals, that are growing in state-of-art seawater farms
under a strict control, with Close-Circuit water system and special
nutrition.
Corals, used for the Coross bone graft, are grown in a controlled
aquarium system. Coross graft material is comprised of the pure
mineral part of the coral. It consists of calcium carbonate crystals
(>95%) in the form of aragonite enriched with essential non-organic
substances that are known to play an essential role in the bone
mineralization process and the activation of enzymatic reactions with
osteogenic cells.
• Attractive to bone cells and stimulates new bone growth and
connectivity.
• Strong Up to 3 times than synthetic bone.
• Optimal porous structure enables vascularity ingrowth and new
bone formation.
• Biodegradable: Remodels by osteoclastic activity.
• Cancellous coral types mix – for the optimal bone formation and
remodeling.
• No biological risks, no marine pollution.
3D Through Porous Structure Bone Deposition into Pores Bone Cells Attracted by Coross
Bioactive surface and interconnected Mineralized matrix of cortical bone Layers of strained active
pores in optimal dimensions for is deposited on the surface of coral osteoprogenitor cells attached to
ingrowth of blood vessels and bone mineral. Ingrown blood vessel inside bioactive coral mineral surface (in 48
deposition. a pore of Coross graft. hours after grafting in vivo).
Titanium-
20.0 x 25.0 PM2025A
Reinforced
Titanium-
25.0 x30.0 PM2530A
Reinforced
Titanium-
30.0 x 40.0 PM3040A
Reinforced
Product Code
Product Code
Syntoss Biogel
It was originally created for treatment of periodontitis, gingivitis and
stomatitis. It can be used to relieve swelling and inflammation of the
tissues in the surgical dentistry, trauma, fractures, splinting of the
jaws.
Product Code
PureSponge
DSI presents PureSponge, a highly porous absorbable collagen
material used as a hemostatic agent and wound dressing in a wide
array of oral surgical procedures, designed to help protect, repair and
heal oral wounds. Prevents the stop of blood thinner intake in heart
patients, prior to any dental surgical procedure. Made from purified
100% bovine collagen type 1.
Sterile, every unit is packaged individually.
Used for:
• Post-extraction tissue void filling.
• Treating periodontal defects.
• Biopsy procedures.
• Treating alveolar ridge defects.
• Socket grafting.
• Treating Schneiderian membrane tears.
• Treating subantral augmentation.
• Sinus graft containment.
• Periodontal guided bone regeneration.
• Soft tissue recontouring.
Features:
• Three convenient shapes for common oral wounds and procedures.
• Protects the wound bed.
• An absorbable matrix supports newly formed tissue.
• Designed to resorb in a prolonged timeframe.
unique root-
Cone Ø 4.0 x 7.0 mm 10 pcs DS-PS47-B
shaped
Size Code
Size Code
Silver Sponge
DSI Silver Sponge is a gelatin collagen sponge of hemostatic action
with the addition of 5% colloidal silver. It is used in a wide range
of surgical procedures, where traditional hemostatic measures
are irrelevant, or inappropriate. Unlike many other bacteriocide
substances, silver from DSI Silver Sponge is not washed away, so last-
lasting depot effect with continuous silver ions release is achieved.
• Absorbed biologically within 3-4 weeks.
• No side effects aid the healing process.
• Seals up the bleeding tissues immediately.
• Prevents blood loss and hemorrhage.
• Presaturated with colloidal silver.
• Kills bacteria with a long-lasting effect.
• Excellent bio-compatibility.
• Purified first-grade gelatin, iodoform-free.
Size Code
Product Code
Sponge Perio
DSI Perio Sponge is a unique biodegradable chip unlike any other
product. Anti-microbial Sponge Perio is easily placed in the periodontal
pocket after root surface removal of damaged tissue. It contains
2.5 mg of chlorhexidine gluconate and no antibiotics. Sponge Perio
biodegrades within the periodontal pocket releasing 40% of the
chlorhexidine in the first 24 hours then it gradually releases the rest
of the chlorhexidine in the next seven days. Over this period Sponge
Perio not only eliminates 99% of subgingival bacteria in the infected
pocket but also reaches the base of the pocket where the root surface
debridement is less effective. It has been shown to be an effective
and safe treatment for patients with adult periodontitis with a pocket
depth equal to or greater than 5mm, when used with scaling and root
planing. For best results, Sponge Perio should be placed every three
months as part of a periodontal maintenance program that promotes
good oral hygiene and root surface debridments.
Sponge Perio is significantly more effective at reducing pocket depth
compared to root surface debridement alone. A two-year study has
shown that almost 60% of periodontal pockets were reduced to less or
equal to 5 millimeters and more than half of them showed a significant
reduction of 2 millimeters.
DSI Perio Sponge insertion takes less than one minute, which makes it
exceptionally easy and fast working product, it saves great amount of
chair time, and unnecessary waiting for the patient.
Features:
• Biodegradable collagen chips.
• Contains Chlorhexidine gluconate 2.5 mg.
• Localised and sustained release of chlorhexidine gluconate.
• Suppresses growth of bacteria in subgingival plaque.
• Minimal patient compliance needed.
• Biodegrades after placement.
• Easy insertion and fast insertion.
• Very effective against periodontitis.
Product Code
Nylon Sutures
DSI Nylon sutures are non-absorbable sutures and possess excellent
tensile strength. Nylon sutures have excellent knot security properties
and can be easily removed with no tissue adherence. These sutures
are infection resistant.
Nylon sutures are widely used for general closure, skin and plastic
surgery. They are usually not recommended for attachment of artificial
prostheses in cardiovascular surgery. They also do not support
infection and maintain tensile strength indefinitely in tissues.
Nylon sutures are available in blue colour.
2/0 DS-NY20
5/0 DS-NY50
Silk Sutures
DSI Silk sutures are entwined thread from silk worm larva. Silk
sutures are coated and braided non-absorbable sutures. Silk sutures
are specially treated with silicone to give strength and smoothen the
surface which provides easy passage through tissues. Silk sutures
have moderate tissue reaction.
Silk sutures are available in black colour.
2/0 DS-SIL20
5/0 DS-SIL50
2/0 DS-CHG20
5/0 DS-CHG50
Wound support: 18-21 days
Total absorption: 50-70 days
2/0 DS-CG20
PGA Sutures
DSI PGA is made from 100% Glycolide popularly known as PGA
Sutures or polyglycolic acid sutures. Is a sterile, absorbable, medium
term, braided suture. PGA sutures exhibit superior tensile strength.
PGA sutures are available in violet colour.
2/0 DS-PGA20
12 individual packs
of 75 cm / 30" suture 3/0 DS-PGA30-N20 DS-PGA30
with pre-installed
reverse cut 3/8 circle 4/0 DS-PGA40-N20 DS-PGA40
atraumatic needle
5/0 DS-PGA50-N20 DS-PGA50
Wound support: 21-28 days
Total absorption: 60-75 days
Implant Cement
DSI Semi-permanent Implant Cement is designed specifically for
implant-retained crowns and is suitable for temporary cementation
of provisional restorations where long-term or increased retention is
desired. It is a tough elastomeric resin that flexes under force, absorbs
shock and resists breaking down under daily occlusal stresses.
Damage free removal of implant restorations. Thin (10 microns) film
thickness for a great fit. Dual cure for easy removal of excess cement
and for a quick and easy application. Compatible with all materials
combinations (Zirconia, Noble Alloys, NP Alloys, Titanium, etc).
Product Code
Product Code
Temp
DSI Temp is a ready to use temporary filling material on a zinc oxide
base. Good adhesion to dentine and excellent marginal adaptation.
This hydrophilic material is cured with oral cavity moisture during 2-3
hours. Pleasant citron taste.
• For temporary filling of cavities.
• Temporary seal for medicaments.
• Repair of lost fillings.
• Restoration of milk teeth (all cavities).
Product Code
Hemostatic Gel
DSI Hemostatic Gel is 25% buffered aluminum chloride thixotropic,
non-dripping gel for stopping minor gingival bleeding during
restorative procedures, placement of metal bands, cervical matrix,
and crowns preparations. Excellent handling properties make it easy
to place for class V composite restorations, cementation and scaling
in periodontic cases.
• Non-staining unlike ferric sulfate which ofter stains porcelain
veneers, crowns, and gingiva.
• Comes with tips.
• Thixotropic gel – convenient to apply.
• Effectively stops minor gingival bleeding.
• Long and stable shelf life.
Product Code
Product Code
Iodoform
• Utilized as a therapeutic pad for the restoration of painful and
inflamed pulp in the case of pulpitis.
• Used under permanent fillings when treating deep caries.
• Have a high pH level (12.5) creating long bactericidal effect,
radiopacity, pulp regeneration.
• Capability to penetrate deeply into dentine canals and seal them as
a result of dough adjuster on water base.
Product Code
Product Code
Product Code
Product Code
Product Code
Chlor-EX 2% Chlorhexidine
• Recommendeded as the part of the surgical and endodontic
disinfection procedures.
• Root canal surface disinfection prior to sensitive root treatment.
• Before the dental crown cementation or luting cement application
by direct restorative placement – minimizes post-operational
sensitivity.
• Highly effective mouth rinse when diluted.
Product Code
Product Code
Product Code
Strip Iodoform
• 100% Cotton with Woven Edges 5 g of Iodoform.
• Perfect for treatment of post-extraction sites.
• Great for the sinus disinfection.
• Effective antimicrobial action.
• Effective adsorption.
• Mildly analgesic action.
• Pronounced bactericidal effect.
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Dental Dam
Latex Dental Dam, Powder Free, Smooth, Non-sterile.
100% Natural Rubber Latex Material. Colour – Green.
• Protect the treated area from being exposed to oral bacteria.
• Prevent the patient's tongue and gums from irritation during
treatment.
• Prevent any debris from falling to the patient's throat.
Product Code
ApexFile Gold
DSI ApexFile Gold visibly advanced metallurgy creates a difference you can see – and feel. ApexFile Gold rotary files
feature exact geometries as increase in flexibility. This is especially important in the Finishing Files, when navigating
challenging curves in the apical region.
Developed with proprietary advanced metallurgy, DSI ApexFile Gold rotary files deliver greater flexibility for predictable
DSI ApexFile Gold performance that’s more brilliant than ever.
• New generation material – 18k gold coated NiTi.
• Improved shapes – structurally appropriate for predictable cleaning, conefit, and obturation.
• High fracture resistance and long-last shaping ability.
• Ideal for a wide range of canal morphologies.
• Compatible with your existing reciprocating handpieces and settings.
• Shorter 11 mm handle.
• Greater
Resistance to
Cyclic Fatigue.
• Increased Flexibility.
ApexFile Gold
Type Product 19 mm 21 mm 25 mm 31 mm Info
Shaping SX 19SX
Shaping Files pre-
enlarge canals and
are designed to be
Shaping S1 21S1 25S1 31S1
used with the same
familiar outstroke
brushing technique.
Shaping S2 21S2 25S2 31S2
Assorted
21SXF3 25SXF3 31SXF3
SX-F3
Product Code
Product Code
Product Code
UniLite Crown
Temporary Crown and Bridge resin-based material with zirconium
nanoparticles for short and long term crown & bridge restorations
• High strength and low wear, excellent polishability.
• High compressive flexural strength, minimum gingival irritation, no
unpleasant taste or smell.
• Easily repaired with flowable composite, enhanced color stability for
less staining.
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Product Code
Cutter with
non- with
Size Aluminum
impregnated Epinephrine
Chloride
Spool
Product Code
Product Code
Product Code
Fluoride Gel
DSI Fluoride Gels are an economical and quick application fluoride
treatment. The gel is a 60-second acidulated phosphate fluoride
that contains 1.23% fluoride ion. The smooth creamy gel will not run
or thicken during treatment. The gel is offered in different flavors
for patient satisfaction and there’s no bitter aftertaste following
application.
Features:
• Prevents cavities.
• Supports healthy tooth enamel.
• Highly viscous.
• Economical.
• Easy and fast application.
• Gourmet flavors.
Prophylaxis Paste
DSI Prophy Paste provides professional-level results at just a fraction
of time and cost of a dentist office procedure.
The special formula provides efficient, non-splatter stain removal
and highly effective polishing, ensuring a healthy, beautiful smile. DSI
Prophy Paste is easy to rinse.
Though this unique combination of both cleaning and polishing
ingredients has been developed for professional use in clinics, DSI
Prophy Paste is also ideal for home use. Simply brush your teeth with
DSI Prophy Pastepaste and an electric toothbrush (the paste cannot
be used more than once a week) and enjoy outstanding results in the
comfort of your own home!
DSI Prophy Paste paste successfully removes tobacco, tea, and coffee
stains, eliminates bacterial toxins, makes your breath minty fresh,
giving you an attractive, shiny smile.
Features:
• Optimal cleaning results.
• Effective and gentle polishing.
• Splatter and residue free formula.
• Easy to rinse off teeth.
• No appreciable abrasion to enamel.
• Only natural flavourings.
• Great taste.
Product Code
Product Code
Repio Liner
A kit for the conditioning of sensitive tissue caused by ill-fitting
dentures.
• Easy to mix.
• Fully elastic and resilient for treatment of painful ridge areas.
• Easily removed when needed for quick follow up treatment.
• Self adhesive – allowing additions to be made.
• Can also be used as a functional impression material.
• Color: translucent pink.
Product Code
UltraSil Reline
UltraSil Reline is an A-silicone material providing comfort and long-
lasting elasticity for indications of sharp or bony alveolar ridges and
undercuts.
It is used to adapt dentures after extractions or implant surgeries.
Characteristics: 1:1 Mixing ratio. Excellent bonding to prosthetic
base with special adhesive Acrylic Bonding Primer. Odourless and
tasteless. Pink Colour.
Product Code
Mixing Pads
Tear-off disposable coated sheets allow easy mixing of materials by
preventing absorption into the surface. Great for mixing any two part
materials including cements, impression and filling materials.
Product Code
Product Code
DSI Barracuda has more aggressive shape and larger head, built for
rotation on very high capacity speeds. Sharp blade geometry and
multiple crosscuts provide the ideal combination for crown removal
and endodontic access, making this bur an ultimate grinding machine.
All DSI TC burs are solid carbide, One-Piece Construction. Their concentric one-piece design eliminates brazed joint
breakage, as well as chatter and vibration. These highly concentric burs result in faster, smoother and more precise cuts.
DSI produces the best carbide burs, with high-hardness, high-purity and high wearability. The tungsten carbide material
we use is the next hardest known material on the planet, after diamonds.
For each procedure, we are equipped with high-precision production devices, such as high-precision grinding machine,
fully-automatic welding machine, etc Apart from these, we purchased the latest 6-axis CNC machines from Swiss (the
same machines we use to make the precise implants and prosthetics).
We also use full-series patented dental burs production software, to ensure the quality of our products. With outstanding
high-sharpness, high-concentricity, and high-precision.
The carbide burs we produce are compatible with all varieties of hand-pieces.
A series of premium quality orthodontic trimming and finishing burs, great for post-treatment adhesive removal. 7 series
burs are 12-braded. Each package contains 10 pieces.
DSI ProxiStrip
DSI IPR Strip System is an innovative, precision dental strip
system designed to achieve ideal proximal contact adjustment
and complete marginal seating of crowns, veneers, inlays/
onlays, and proximal contouring of composite fillings accurately
with minimal time and effort. ProxiStrip IPR Strip System makes
interproximal enamel stripping safe and accurate without
creating sharp corners or subgingival ledges. Designed for use
with orthodontic treatments, these flexible strips curve and
conform to the natural contours of the teeth to maximize patient
comfort and safety.
The ProxiStrip comes with a sawtooth edge strip(Blade) for
cutting through, and three different types of an abrasive
corrugated surface strip for cleaning the interdental space and
polishing the teeth surface. Also, the kit includes the key to the
holder for opening and closing.
The main advantage of the DSI ProxiStrip System is the long
handle that gives you the option to get to hard to reach areas and
difficult angles. With it, you can operate at a long distance and be
able to get even to the farthest oral areas. It also gives the ability
to operate in angle axis up to 90°, which greatly reduces the time
Versatile joint connection – up to
spent on any dental operation. There is no other system equipped 90° angle from the handle axis for
with such a device. maximum performance.
DSI ProxiCut
DSI Proxicut is an innovative, precision dental strip system designed to achieve ideal proximal contact adjustment and
complete marginal seating of crowns, veneers, inlays/onlays, and proximal contouring of composite fillings accurately
with minimal time and effort.
Proxicut IPR Strip System makes interproximal enamel stripping safe and accurate without creating sharp corners or
subgingival ledges. Designed for use with orthodontic treatments, these flexible strips curve and conform to the natural
contours of the teeth to maximize patient comfort and safety.
The proxicut comes with a sawtooth edge strip(Blade) for cutting through, and abrasive corrugated surface strip for
cleaning the interdental space and polishing the teeth surface.
Advantages:
• Single-handed, ergonomic design offers optimal tactile
control and reduces hand fatigue.
• Eliminates the need to hold small restorations and use
rotary instruments or articulating films.
• Central opening for enhanced visual perception and
access for tools.
• Patient-friendly design prevents gagging and soft tissue
irritation.
• Flexible strips conform to the natural contours of the
teeth to avoid creating sharp corners.
• Autoclavable and reusable.
• Will not remove excessive enamel.
• Saves chair-time.
• Effective both in anterior and posterior areas.
3D Resin Basic
Designed for daily use in 3D printers for printing models.
Odorless, with outstanding rigidity, low shrinkage and high accuracy.
DSI 3D Basic resin Designed for daily use in 3D printers for printing
models. Resin is odorless, models characterized by rigidity, low
shrinkage and high accuracy. Basic Resin is a good choice for taking
your first steps in 3D printing. The absence of odor and low toxicity
makes the resin ideal for use in the office, schools and universities.
It is easy-to-operate with it due to low viscosity – easy to fill vat, to
filter, to clean model and printer parts. Resins are very accurate in
wide area of curing time, that provide a good quality even at mistaken
exposure, which reduces the time for learning 3D printing skills.
3D Resin Cast
Designed for printing models, used for direct casting.
Zero ash content and ready to use in shock cycles makes it possible
to obtain high quality castings.
DSI 3D dental Cast resin is excellent for direct casting of dental
implants like metal and ceramic crowns and bridges. Almost zero ash
content (less than 0.1%) and thermoplastic properties makes the resin
suitable for direct casting.
The resin was designed to burn out in a quick cycle at high
temperature to reduce electricity costs and the production time of
metal and ceramic implants.
To obtain the best quality surface from casting, we recommend
the use of phosphate-based investments that can operate at high
temperatures.
3D Resin Master
Designed for dental demonstration models and master-models.
Tough, hard, stable on high temperatures – safe to use with
thermoforming aligners.
DSI 3D dental Master resin is matt pale orange colored resin, made
of biocompatible raw materials used in UV-cured dental fillings. It
has high hardness 87 Shore D and high tensile strength, stability to
mechanical and thermal stress.
We recommend using it for demonstrational and master-model
printing. Low odor and absence of harmful monomers allows to print
in the laboratory.
3D Resin Gingiva
Designed for dental demonstration models of gingiva with yellowish
pink color.
Tough, glossy and stable to deformations.
DSI 3D dental Gingiva resin is PMMA-like resin, made of biocompatible
raw materials, with gum semi-transparent color. It has high hardness
87 Shore D and high tensile strength, durable to mechanical stress.
Recommended for printing of dental model of gum color such as
gingiva mask. Low odor and absence of harmful monomers allows to
print in the laboratory.
3D Resin Guide
Designed for surgery guide modelling.
Precise, transparent, very tough and hard, odorless.
DSI 3D dental Guide resin is hard PMMA-like resin, made of
biocompatible raw materials that used in UV-cured dental fillings. It
has high hardness 92 Shore D and high tensile strength, stability to
mechanical stress. We recommend to use it for surgical guides and
master-model printing. Low odor and absence of harmful monomers
allows to print in the laboratory.
3D Resin Tray
Designed for printing of transparent clear models, such as aligners,
kappa.
Precise, transparent, very tough and hard, odorless.
DSI 3D dental Tray resin is hard PMMA-like hard clear resin designed
for printing models, used in dental application, where transparency
is one of the main issues. Can be used for demonstration models,
required for operation planning, aligners, surgical guides.
DS3D-LAB- DS3D-LAB-
Natural
NATURAL-500 NATURAL-1000
DS3D-LAB-
Cherry DS3D-LAB-CHERRY-500
CHERRY-1000
DS3D-CROWN- DS3D-CROWN-
Crown&Bridge Resin A1/A2
A1A2-500 A1A2-1000 Provisional Crowns & Bridges,
anterior and posterior tooth
restorations
Crown&Bridge Resin A3 DS3D-CROWN-A3-500 DS3D-CROWN-A3-1000
Aligners, Mouthguards,
Tray Resin Clear DS3D-TRAY-500 DS3D-TRAY-1000 Splints, Custom impression
trays and Bracket positioners
Table 1:
Components REF Code Material
DSI Premium Spiral
Implant Internal Hex 2.42 Titanium Ti6Al4V Eli
SPI 1635
Connection – Ø 3.5 mm x Grade 23
L 16 mm
DSI Standard Titanium
Angulated Abutment 25˚,
STAA 25-3 Ti 6Al 4V Titanium Alloy
3 mm Shoulder Height,
Hex Connection
Implant Materials
DSI Implants product used in the testing are made of 6AL-4V Eli
alloyed Grade of Titanium. It is strengthened by the inclusion of
roughly 6% Aluminum and 4% Vanadium. Titanium 6AL-4V Eli (Extra-
Low Interstitial) is considered a higher purity than 6AL-4V Grade 5 due
to its lower inclusions of Iron, and the interstitial elements, Carbon
and Oxygen. 6AL-4V Eli typically comes in the annealed condition, but
can be found in beta annealed condition as well. 6AL-4V Eli Grade
23 shows high strength and toughness, as well as good corrosion
resistance. It is found in aerospace applications where fracture
toughness and fatigue strength are important. As a biocompatible
Grade of Titanium, it is also known for its applications in medical and
dental industries.
Table 2:
Composition Analysis
Aluminum: 5.5 – 6.5% Carbon (Maximum): 0.08%
Vanadium: 3.5 – 4.5% Nitrogen (Maximum): 0.05%
Iron (Maximum): 0.25% Hydrogen (Maximum): 0.012%
Oxygen (Maximum): 0.13% Titanium: Balance
Table 3:
Tensile Properties (Minimums)*
Tensile: 120 – 125 ksi Elongation: 8 – 10%
Yield: 110 – 115 ksi Reduction of Area: 15 – 25%
Testing configuration
To text fatigue strength, an implant, potted into acrylic sleeve 3mm
below the bone level, with the abutment is mounted in a fixture
with a 35° off-axis orientation (which simulates the 10 defrees of
uncorrected angulation), then a cyclic force is applied with frequency
of 15 motions per second.
The implant/abutment system is tested at a range of forces to
determine the maximum load at which it will survive a 5,000,000
cycles. From the results, the endurance of implant system can be
established.
3. Strain gage load cell, S/N 654288, C26414, 745708, & 656359 with
an Ellis Associates Model BA-13 bridge/amplifier for dynamic load
readout.
All of the above test equipment was in current calibration, and adhere
to ANSI Z540-1-1994 and ISO 10012-1 standards.
3. Connecting part.
6. Specimen holder.
Load
Point loading at machine end, laterally
unconstrained.
35°
10°
1
2
4
5
6
8
11
3
700
600
500
Max Load (N)
400
300
160
150
140
Max Load (lbf.)
130
120
110
End of test
600
500
Maximum Applied Fatigue Load (N)
400
300
200
0
1,000 10,000 100,000 1,000,000 5,000,000 10,000,000
Cycles to Failure
400
Figure 4: Endurance Limit from Fatigue
Testing of Implants with Angled Abutment
from Various Manufacturers.
300
Max Load (N)
200
References Tables
C1. Gubbi P., Davis B., Towse R. Traylor M. An Evaluation of Table 1: DSI Premium Implant System Component.
Strengths of Various Dental Implant Systems from Standardized Table 2: Composition Analysis.
Fatigue Testing. Biomet 3i®, Palm Beach Gardens, Florida, USA. Table 3: Tensile Properties.
2. Fatigue of Materials, Suresh s., Cambrige Univ. Press.
3. Quek, CE, Tan, KB, Nicholls, JI. (2006). Load fatigue
performance of a single-tooth implant abutment system: effect
of diameter. The International Journal of Oral & Maxillofacial
Figures
Implants. 21, 929–936. Figure 1: ISO 14801 Schematic of Test Set-Up for systems
4. Fatigue of Dental Implants: Facts and Fallacies. Keren with an Angulated Implant Abutments.
Shemtov-Yona and Daniel Rittel. Faculty of Mechanical Engng, Figure 2: Static Compression Tests – ultimate static load
Technion, Haifa, Israel. results for DSI Premium Spiral Implant Internal Hex 2.42
5. Fracture strength of implant abutments after fatigue testing: Connection – Ø 3.5 mm x L 16 mm and DSI Standard
A systematicreview and a meta-analysis Coray, Rafaela; Zeltner, Titanium Angulated Abutment 25˚, 3 mm Shoulder Height,
Marco; Özcan, Mutlu, University of Zurich. Hex Connection.
6. Biomechanical characterization of narrow diameter dental Figure 3: Fatigue Curve – Dental Solutions Israel Standard
implantsDonald Responte, PhD, Senior Test Engineer, Zimmer Titanium Angulated Abutments 25º, 3 mm Shoulder Height,
Biomet®. Hex Connection on SPI 3.5 mm Hex Connection Implants.
7. ISO 14801 Dentistry Implants – Dynamic Fatigue Test for Figure 4: Endurance Limit from Fatigue Testing of Implants
Endosseous DSI Implants, ISO2016. with Angled Abutment from Various Manufacturers.
The DSI brands understand this fundamental principle: there is nothing more powerful
than employees’ passion and initiative to make a good company a Great one.
VISIT US ONLINE WWW.DSISRAEL.COM
DENTAL SOLUTIONS ISRAEL
EN ISO 13485:2016
Certification for
Medical Devices,
BSI Group, UK