Professional Documents
Culture Documents
Catalog - Door Closer - Hafele - en
Catalog - Door Closer - Hafele - en
Catalog - Door Closer - Hafele - en
Information
Door closer
4
a Backcheck c Closing delay
With backcheck, the swing of a forcefully opened door The closing delay increases the closing time so that, for example,
(manually or for example by gusts of wind) is reduced. persons carrying luggage or bulky items, to mothers with prams,
Damage to the door or wall are therefore minimised or eliminated. elderly persons, etc. have sufficient time to walk through the door.
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Overhead installation
Standard installation
(Transom fixing) on the push side
(Door leaf installation) on the push side
Standards
There are two standards currently in existence for door closing devices: EN 1154: 1997 - Controlled door closing devices
EN 1154: 1997 - Mechanical closers - requirements and test methods.
EN 1155; 1997 - Electronically controlled closers
These standards are shown in summary below and in detail at the back Scope - The standard covers all controlled surface mounted, con-
of this catalogue. Attention should be paid to Digit 3, which deals with cealed,or transom mounted closers as well as both single and
the power size and door width. Where applicable we have shown the double action floor springs.
relevant classification code using DHF graphic icons in this section.
Classification
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
7 160 kg 1,600 mm
EN 1154 makes the following recommendations as to the d) Control regulators shall be either concealed or operable only by
feature considered necessary for such devices when they are fitted means of a tool.
to fire and smoke resisting doors.
e) The design of a door closer shall be such that it is not possible
a) The door closer when installed in accordance with the manu- to inhibit its closing action in any way without the use of a tool.
facturer's installation instruction shall be capable of closing the
test door from any angle to which it may be opened. f) Any incorporated delayed action function shall be capable of
adjustment to less than 25 seconds between the door closing
b) Due to their low closing moments, door closers sizes 1 and 2 angle of 120° and the end of the delay zone.
are not considered suitable for use on fire/smoke resisting door
assemblies. Door closers with adjustable closing force shall be g) The door closer representative of its model shall have been
capable of adjustment to at least power size 3. incorporated in a door assembly that has satisfied the
appropriate criteria of a fire test. The test shall have been on a
c) The door closer shall not include a hold open device unless it is full size assembly in accordance with EN 1634-1.
electrically powered device in accordance with EN 1155.
Classification
public,and others, with little incentive to take care, i.e. where for a range of power sizes both the minimum and the
there is some chance of misuse of the door. maximum sizes shall be identified.
3 60 kg 950 mm
Digit 2 - Number of test cycles 4 80 kg 1,100 mm
Two test durations are identified for devices manufactured to 5 100 kg 1,250 mm
6 120 kg 1,400 mm
this European standard:
7 160 kg 1,600 mm
Grade 5: 50,000 cycles. For all stand alone electrically
powered hold open devices Digit 4 - Fire behaviour
Grade 8: 500,000 cycles. For all stand alone electrically Only one grade of fire resistance is identified for the
powered hold open and free-swing door closers and electrically powered hold-open devices
devices that contain operating arms. Grade 1: Suitable for use on fire/smoke door assemblies,
subject to satisfactory assessment of the contribution of the
emergency device to the fire resistance of specified
fire/smoke door assemblies.
Where a door closing device has a CE certificate of conformity, this Tested for fire resistant and smoke control doors.
4 will be shown thus. It is stated in 8300 that all fire doors must
have closing devices that are CE marked. The use of a hold-open device on fire resistant
and smoke control doors are not permitted or they are
not tested for resistant and smoke control doors
We give below a guide to the terminology used in connection with Delayed action
door closing devices. The closing speed of the door is reduced to
minimal or the door stops, for a preset period, to allow passers-by
Backcheck sufficient time to pass through the door opening. i.e. Elderly
A device built into the closer that checks the outward persons, Hospital staff with beds, etc.
swing of the door. The backcheck damping is inversely
proportional to the speed of the outward swing of the door. Hold open
It should not be regarded as a door stop. This is a device to enable the closer to be held in the open posi-
tion, usually at 90º, but some are variable in the opening degree.
Closing speed
These closers must not be used on fire doors.
The speed with which the door is closed. Normally
(except where they are electronically controlled to close when the
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
adjustable.
fire alarm is sounded).
Closing force
The power that the closer exerts to close the door. Door stops
Measured in the EN standard from 1-6. See table below. Always use a door stop, where practicable, whether a
closer has a backcheck or not. This may take the form of a floor
Size Max. door width mm Min. closing moments N.m mounted version, wall/skirting mounted version or built-in as found
with guide rail closers. The positioning of the stop is also impor-
tant, and must be at least 66% (2/3rds) the door width away from
1 750 9 the hinge, otherwise the stop acts as a fulcrum and could damage
2 850 13
the door, the frame and the hinges. Where there is a maximum an-
3 950 18
gle of opening stated the stop must be positioned at that point,
4 1100 26
otherwise damage to the closer will occur.
5 1250 37
6 1400 54
Note
It should be noted that size 3 is the minimum requirement for fire
Please ensure that the correct closing device is the
doors.
appropriateone for the job it is intended to do and that it is the
Latching action correct size. Too many closers are under specified, purely in an
The door movement becomes accelerated in the last few degrees effort to reduce costs.
of closing, in order to be able to overcome any
resistance, such as seals, latch bolts, etc.
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
4
Technical data
Closing force size EN3
Door width size 850–950 mm
Max. door weight 60 kg
Max. door opening angle Approx. 180º
Hold open angle 70–145°
Packing: 1 pc.
Features
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
4 • Suitable for DIN right hand and DIN left hand
• Closing force according to EN 1154
Technical data
Closing force size EN3
Door width size 850–950 mm
Max. door weight 60 kg
Max. door opening angle Approx. 180º
Hold opening angle Approx. 90º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
(door leaf installation) on pull side (transom fixing)on push side
Packing: 1 pc.
Features
• Latching action valve adjustable
• Closing speed valve adjustable
• Backcheck valve adjustable
• Suitable for DIN right hand and DIN left hand
• Closing force acccording to EN 1154
4
Technical data
Closing force size EN3
Door width size 850–950 mm
Max. door weight 60 kg
Max. door opening angle 180º
Hold open angle 70–145º
Packing: 1 pc.
Features
• Tested to EN 1154
• Tested to conform with CE requirements
• Variable closing force by installation position of body
4 • Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• On request available with backcheck
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN2–EN4
Door width size 750–1,100 mm
Max. door weight 80 kg
Max. door opening angle Approx. 180º
Hold open angle 70–150º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Standard installation Overhead installation Parallel arm installation
(door leaf installation) (transom fixing) 2QSXVKVLGH
on pull side on push side
Packing: 1 pc.
Order reference
Parallel arm bracket .................................................page 4.26
Features
• Variable closing force by installation position of body
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• With fixed backcheck
• With interlocking hold-open device
• Suitable for DIN right hand and DIN left hand 4
• Closing force according to EN 1154
Technical data
Closing force size EN2–EN4
Door width size 750–1,100 mm
Max. door weight 80 kg
Max. door opening angle Approx. 140º
Hold open angle 70–140º
Packing: 1 pc.
Features
• Tested to EN 1154
• Tested to conform with CE requirements
• Closing force valve adjustable
• Latching action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
• Closing force according to EN 1154
4 Technical data
Closing force size EN2–EN4
Door width size 750–1,100 mm
Max. door weight 80 kg
Max. door opening angle 115º
Max. hold open angle 115º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Version Silver colour
Packing: 1 pc.
Features
• Tested to EN 1154
• Tested to conform with CE requirements
• Closing force adjustable by valve
• Hydraulic latching action valve adjustable 4
• Closing speed valve adjustable
• Backcheck valve adjustable
Technical data
Closing force size EN2–EN5
Door width size 750–1,250 mm
Max. door weight 100 kg
Max. door opening angle Approx. 180º
Hold open angle 70–150º
Packing: 1 pc.
Order reference
Parallel arm bracket .................................................page 4.26
Features
• Tested to EN 1154
• Tested to conform with CE requirements
• Closing force adjustable by valve
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Standard installation Overhead installation
(door leaf installation) on pull side (transom fixing)on push side
Packing: 1 pc.
Features
• Closing force valve adjustable
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• Backcheck valve adjustable
• Closing force according to EN 1154 4
Technical data
Closing force size EN2–EN4
Door width size 750–1,100 mm
Max. door weight 80 kg
Max. door opening angle Approx. 140º
Hold open angle 70–120º
Packing: 1 pc.
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Variable closing force with arm assembling
4 • Latching action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN2–EN3
Door width size 750–950 mm
Max. door weight 80 kg
Max. door opening angle 180º
Hold open angle 70–150º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Standard installation Overhead installation
(door leaf installation) on pull side (transom fixing)on push side
Packing: 1 pc.
Features
• Tested to EN 1154
• Tested to conform with CE requirements
• Variable closing force with arm assembling
• Latching action valve adjustable
4
• Closing speed valve adjustable
• On request available with backcheck
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN3–EN4
Door width size 850–1,100 mm
Max. door weight 85 kg
Max. door opening angle Approx. 180º
Hold open angle 70–150º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Features
• Latching action valve adjustable
• Closing speed valve adjustable
• On request available with backcheck
• Suitable for DIN right hand and DIN left hand
• Closing force according to EN 1154
Technical data
Closing force size EN2
4 Door width size 750–850 mm
Max. door weight 85 kg
Max. door opening angle Approx. 130º
Hold open angle 70–150º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Version Silver colour Dark bronze White RAL 9016
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Variable closing force due to offset installation(size EN2/EN4/EN5)
• Closing speed valve adjustable
• Latching action adjustment via an arm assembly
• Suitable for DIN right hand and DIN left hand
Technical data 4
Closing force size EN2–EN5
Door width size 750–1,250 mm
Max. door weight 120 kg
Max. door opening angle Approx. 180º
Hold open angle 70–150º
Order reference
Parallel arm bracket .................................................page 4.26
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Variable closing force due to offset installation (size EN2 and EN3)
• Closing speed valve adjustable
• Optional whit hold-open device (not fire rated)
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN2–EN3
4 Door width size 750–950 mm
Max. door weight 120 kg
Max. door opening angle Approx. 130º
Hold open angle 80–130º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Version Silver colour Dark bronze White RAL 9016
Features
• Not to be used an fire doors
• Allows infinitely variable hold open between 80°–130º
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Closing force valve adjustable
• Closing speed valve adjustable
• With backcheck valve adjustable
• Latching action adjustment via an arm assembly
• Suitable for DIN right hand and DIN left hand
• Optical indicator for closing force 4
Technical data
Closing force size EN1–EN6
Door width size 650–1,400 mm
Max. door weight 200 kg
Max. door opening angle Approx. 180º
Hold open angle 70–150º
Order reference
Parallel arm bracket .................................................page 4.26
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Closing force valve adjustable
• Closing speed valve adjustable
• With backcheck valve adjustable
• Suitable for DIN right hand and DIN left hand
• Optical indicator for closing force
Technical data
4 Closing force size EN 1–EN5
Door width size 650–1,250 mm
Max. door weight 200 kg
Max. door opening angle Approx. 130º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Version Silver colour Dark bronze White RAL 9016
Features
• Not to be used an fire doors
• Allows infinitely variable hold open between 80°–130º
Features 4
• Tested to EN 1154 and EN1155
• Tested to confirm with CE requirements
• When voltage applied to closer - the door hold open
• Voltage off - door close automatically
• The door can be closed manually at any time regardless of
whether the voltage is applied or not
• Closing speed and closing force is valve adjustable from the front
• Latching action adjustable via arm assembling
• Suitable for DIN right hand and DIN left hand
• Optical indicator for closing force
• Operating voltage 24V DC ±10%
• Enclosure rating IP43
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Packing: 1 pc.
Accessories
Parallel arm bracket Clamping plate for all-glass doors for TS 2000
Features
• For installation of door closer to all-glass doors
4 • For max. 10 mm glass thickness
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Features
• For installation of the door closer to all-glass doors
• For max. 10 mm glass thickness
Finish Cat. No.
Features
• Latching action valve adjustable
• Closing speed valve adjustable
• Optional with hold open arm
• Closingforce according to EN 1154
Technical data 4
Closing force size EN3
Door width size Max. 950 mm
Max. door opening angle Approx. 180º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Order reference
Door closer sizes EN2–EN6 are available on request.
Features
• Rebate door closer
• For flush and rebated single action doors
• Size adjustment by adjusting the closing force from the front
when the door is open
• Variably adjustable closing speed
• Door strike can be switched off
• Suitable for DIN right hand and DIN left hand
Technical data
A B
Max. door leaf width 1,100 mm 1,250 mm
Max. door opening angle Approx. 140° Approx. 140°
Max. door leaf weight 80 kg 140 kg
Min. door panel thickness 30 mm 40 mm
Latching action from Approx. 7° Approx. 7°
4 A 931.24.000
B 931.24.010
Packing: 1 pc. (supplied with fixing screws)
Installation
• Concealed installation on the pull side in the vertical
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
door rebate below the upper door hinge
• By max. door opening a door stopper must be used
Features
• Tested to EN 1154
• Cam-action
• Tested to confirm with CE requirements
• Door closer for concealed installation in the door leaf or frame
• Closing force valve adjustable
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN2–EN4
Door width size 750–1,100 mm 4
Max. door weight 80 kg
Max. door opening angle 115º
Max. hold open angle 115º
Min. door panel thickness 42 mm
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Door closer for concealed installation in the door leaf or frame
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN3
Door width size 850–950 mm
4 Max. door weight 60 kg
Max. door opening angle 120º
Max. hold open angle 115º
Min. door panel thickness 40 mm
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Features
• Door closer for concealed installation in the door leaf or frame
• Hydraulic lathcing action valve adjustable
• Closing speed valve adjustable
• Suitable for DIN right hand and DIN left hand
Technical data
Closing force size EN4
Door width size 950–1,100 mm
Max. door weight 80 kg
Max. door opening angle 120º 4
Max. hold open angle 115º
Min. door panel thickness 40 mm
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Door closer for concealed installation in the door leaf and frame
• Closing force valve adjustable
• Latching action valve adjustable
• Closing speed valve adjustable
• Backcheck valve adjustable
• Suitable for DIN right hand and DIN left hand
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Sliding channel with interlocking hold-open device 931.14.219
Note
Please take out the hold-open device of sliding channel when needing door closer version without hold-open function.
Please take out hold-open device when using for fire door.
Features
• Tested to EN 1154
• Tested to confirm with CE requirements
• Door closer for concealed installation in the door leaf and frame
• Closing force valve adjustable
• Latching action valve adjustable
• Closing speed valve adjustable
• Backcheck valve adjustable
• Suitable for DIN right hand and DIN left hand
Technical data
4
Closing force size EN3–EN6
Door width size 950–1,400 mm
Max. door weight 180 kg
Max. door opening angle Approx. 120º
Min. door panel thickness 50 mm
Hold-opening range 80–120º
Note
Please take out the hold-open device of sliding channel when needing door closer version without hold-open function.
Please take out hold-open device when using for fire door.
Door width mm
Features
• For single or double action aluminium framed doors
• Hydraulic latching action valve adjustable
• Closing speed valve adjustable
• With hold-open function 90º
• With side-load arm angle bracket and floor pivot
• Closing force according to EN 1154
Technical data 4
Closing force size EN2 EN3 EN4
Max. door width size 850 mm 950 mm 1,100 mm
Max. door weight 80 kg 100 kg 120 kg
Max. door opening angle Approx. 130º Approx. 130º Approx. 130º
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Packing: 1 pc.
4
Features
• Surface mounted sliding door closer, for lightweight
doors only, with closing speed and closing power adjustment
• Suitable for door sizes: 590–900 mm
• Door opens lightly and closes automatically
• Shuts out noise, gases, dust etc. saves energy
• For timber or metal doors
• Max. door weight per leaf: 40 kg
We reserve the right to alter specifications without notice (SEA Architectural Hardware 2015).
Packing: 1 pc.