Professional Documents
Culture Documents
TDS Sikasil SG-18 Structural Sealant
TDS Sikasil SG-18 Structural Sealant
TDS Sikasil SG-18 Structural Sealant
Sikasil® SG-18
Structural silicone adhesive
35 °C 23 °C
gunned into place. Joints must be
8 laboratory tests. Actual measured
properly dimensioned as changes
50 °C data may vary due to circumstan-
8 °C are no longer possible after con-
6 ces beyond our control.
struction. Basis for calculation of
4 the necessary joint dimensions are
50 °C / 95 % r.h. Health and Safety Information
35 °C / 90 % r.h. the technical values of the adhe-
2 For information and advice re-
23 °C / 50 % r.h. sive and the adjacent building
0
8 °C / 30 % r.h.
materials, the exposure of the garding transportation, handling,
0 2 4 6 8 10 building elements, their construc- storage and disposal of chemical
Time [days] products, users shall refer to the
tion and size as well as external
Diagram 1: Curing speed 1-C-Sikasil® SG-18 loads. Joints deeper than 15 mm actual Safety Data Sheets
should be avoided. containing physical, ecological,
Application Limits For more information please con- toxicological and other safety-
® related data.
Most Sikasil WS, FS, SG, IG, WT, tact the Technical Department of
AS and other engineering silicone Sika Industry.
sealants manufactured by Sika are Disclaimer
compatible with each other and Tooling and finishing The information, and, in particular, the
® recommendations relating to the appli-
with SikaGlaze IG sealants. For Tooling and finishing must be
specific information regarding carried out within the skin time of cation and end-use of Sika products,
are given in good faith based on Sika's
compatibility between various the sealant or adhesive.
® ® current knowledge and experience of
Sikasil and SikaGlaze products Prior to the tooling process, ensure the products when properly stored,
please contact the Technical joint flanks are wetted properly. handled and applied under normal
Service Department of Sika conditions in accordance with Sika's
Removal
Industry. All other sealants have to ® recommendations. In practice, the
Uncured Sikasil SG-18 may be differences in materials, substrates and
be approved by Sika before using
® removed from tools and equipment actual site conditions are such that no
them in combination with Sikasil ®
with Sika Remover-208 or an- warranty in respect of merchantability
SG-18. Where two or more
other suitable solvent. Once cured, or of fitness for a particular purpose,
different reactive sealants are nor any liability arising out of any legal
the material can only be removed
used, allow the first to cure relationship whatsoever, can be in-
mechanically.
completely before applying the ferred either from this information, or
Hands and exposed skin should be
next. ® from any written recommendations, or
® washed immediately using Sika
Sikasil SG, IG and WT sealants from any other advice offered. The user
Handclean towels or a suitable of the product must test the product’s
and adhesives may only be used in
industrial hand cleaner and water. suitability for the intended application
structural glazing or window bond-
Do not use solvents! and purpose. Sika reserves the right to
ing applications by experienced
change the properties of its products.
professionals and after a detailed Overpainting The proprietary rights of third parties
®
examination and written approval Sikasil SG-18 is an elastic adhe- must be observed. All orders are ac-
of the corresponding project details sive and cannot be overpainted. cepted subject to our current terms of
by the Technical Department of sale and delivery. Users must always
Sika Industry. refer to the most recent issue of the
The compatibility of gaskets, local Product Data Sheet for the pro-
backer rods, setting blocks and duct concerned, copies of which will be
other accessory materials with supplied on request.
®
Sikasil SG-18 must be tested in
advance.
Sika Schweiz AG
Business Unit Industry
Sikasil® SG-18 2 / 2
Tüffenwies 16
CH-8048 Zurich
Switzerland
Tel. +41 58 436 40 40
Fax +41 58 436 55 30