Professional Documents
Culture Documents
5.000in 0.362wall IEU S135 NC50 (6.625 X 3.250 TJ) 9P 12B
5.000in 0.362wall IEU S135 NC50 (6.625 X 3.250 TJ) 9P 12B
Notes: Pipe Properties are calculated based on uniform OD and wall thickness
New = 100% RBW. Premium = 80% RBW
Burst Pressure for New based on 87.5% RBW per API
Tool Joint 120,000 psi Material Yield Strength Drill Pipe Assembly with Grant Prideco
NC50 (4-1/2" IF) OD (in) 6.625 NC50 Conventional Connection
ID (in) 3.250 New
(New guaranteed 95%
RBW Pipe with IPC)
Pin Tong Length (in) 9.0 Adjusted Weight (lbs/ft) 23.52
Box Tong Length (in) 12.0 Approximate Length (ft) 31.7
*Torsional Strength (ft-lbs) 51,200 Fluid Displacement (gal/ft) 0.36 (without IPC)
Max Recommended Make-up Torque (ft-lbs) 30,700 Fluid Capacity (gal/ft) 0.70 Fluid Capacity (gal/ft) 0.71
Min Recommended Make-up Torque (ft-lbs) 25,600 Fluid Capacity (bls/ft) 0.017 Fluid Capacity (bls/ft) 0.017
Tensile Strength at Max Recommended MUT (lbs) 1,133,400 Drift Size (in) 3.125
Tool Joint/Drill Pipe Torsional Ratio (New Pipe) 0.69
Tool joint/Drill Pipe Torsional Ratio (Premium Pipe) 0.88 Max Upset OD (in) 5.125
Balance OD (in) 6.390
Minimum OD for Premium (in) 6.313 Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of
95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill
tolerances, internal plastic coating tolerances, and other factors.
*Connection torsional strength is less than 80% pipe body torsional strength New pipe guaranteed to 95% RBW will have a smaller ID (4.218'') than new pipe guaranteed to 87.5% RBW
Smooth Edge Nominal Worn to min TJ OD
Height TJ OD for API Premium
Box OD (in) 6.812 6.625 6.313
Elevator Capacity (lbs) 1,658,000 1,440,200 1,073,700
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy
and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall
thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end
user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per
Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
JCT 03-21-2011
Torque‐Tension Graph
Connection: NC50 (6.625 (in) OD X 3.250 (in) ID) SMYS = 120,000 (psi)
Pipe Body: 80% Inspection Class, 5.000 (in) OD, 0.362 (in) wall thickness, S‐135 Pipe Grade
(safety factor = 1.0)
1,400,000
Pipe Body in Combined Loading
Pipe Body Yield at 80%
Inspection Class
1,200,000
Connection Performance (based on MUT)
Tool Joint Yield
1,000,000 Tool Joint Shoulder Separation
TJ Operational Limit (Rec MUT)
TJ Operational Limit (Min MUT)
Tenssion (lbs)
800,000
600,000
400,000
200,000
Torque (ft‐lbs)
Connection Wear for NC50 (6.625 (in) OD X 3.250 (in) ID)
Material SMYS (specified minimum yield strength) = 120,000 (psi)
60,000
50,000
40,000 Connection
Torsional Strength
Torque (ft‐lbs)
Recommended MUT
Minimum MUT
30,000
T
Pipe Body
20,000 80% of Premium Pipe
Body Torsional Strength
Pipe Body: 5.000 (in) OD, 0.362 (in) wall
thickness, S‐135 Pipe Grade
10,000
Tool Joint OD (in)