Professional Documents
Culture Documents
Network Amplifiers: Configurable Single Amplifier/deep Fibre Node
Network Amplifiers: Configurable Single Amplifier/deep Fibre Node
Network Amplifiers: Configurable Single Amplifier/deep Fibre Node
Overview
The Technetix DBC-1200 amplifier is an innovative power supply and uses thermal fuses to provide the
‘crossover’ design which provides a field upgradeable powering modes required for the modules used.
solution to deep fibre/fibre to the last amplifier (FttLA). Its
RF function can be configured for use as a two output Gas discharge tubes at the input and output ports protect
device (with or without an internal splitter/directional the RF circuits in the event of lightning or mains power
coupler). surges.
• EQ
DBDS-XX downstream module
JXP
Plug-in items
• 0dB JXP
• 4/4 splitter
SPS • DC-8
• DC-12
e: sales@technetix.com w: www.technetix.com
Input RF configuration
Input Port Output Port 2 Output Port 1
Bypass Port
(available with
DBC-1200 - configurable single amplifier/deep fibre node
D/A Tuner H • EQ
E
O Plug-in items
• 0dB JXP
• 4/4 splitter
• DC-8
• DC-12
SPS
e: sales@technetix.com w: www.technetix.com
Input Fibre configuration
Input Port Output Port 2 Output Port 1
Bypass Port
(available with
(available with plug-in splitter)
plug-in splitter)
Network amplifiers
DBC-1200 - configurable single amplifier/deep fibre node
Specifications
Electronic controls:
Forward path
Pass band (dependent on diplex) 54/85/102/105/258 - 1218 MHz1 Downstream module
Response flatness (worst case) 54 - 700 MHz ± 0.5 dB Attenuation pre-stage
Response flatness (worst case) 700 - 1218 MHz ± 0.75 dB Attenuation inter-stage
Average full gain 44/38 dB1,6 Equalization pre-stage
Return loss (min) 18 dB2 Equalization inter-stage
Noise figure with zero dB attenuation installed (max) 7.0 dB3, 6 RF power level – high or low power mode
Operating output level CENELEC 42 channels flat (low power mode) 110 dBµV Upstream module
Operating output level CENELEC 42 channels with 8 dB tilt (low power 111 dBµV Attenuation
mode)
Equalization
Operating output level CENELEC 42 channels flat (high power mode) 114 dBµV
Ingress switch control 0dB,-6dB,-40dB (local control or
Operating output level CENELEC 42 channels with 8 dB tilt (high power 116 dBµV
FSK remote control)
mode)
Gain control (electronic) pre-stage 0 - 20 dB6 Digital control module
EQ control (electronic) pre-stage 0 - 25 dB6, 7 AGC/ALSC pilot frequency 1 (where used)
Gain control (electronic) inter-stage 0 - 16 dB6 ALSC pilot frequency 2 (where used)
EQ control (electronic) inter-stage 0 - 15 dB6, 7
Available options
Input monitoring point -20 ± 1.5 dB
Output directive testpoint -20 ± 1 dB w.r.t output JXP style HPF filters , attenuators
Reverse path JXP style Cable Simulators 1,2GHz
Pass band (dependent on diplex) 5 - 204 MHz 4/4 splitter , DC-8 and DC-12 coupler
Input to output port gain 25/28 dB1,6 Band-split 65/85 (pluggable diplex)
Return loss (min) 18 dB2 Band-split 85/105 (pluggable diplex)
Response flatness ± 0.5 dB Band-split 85/102 (pluggable diplex)
Noise figure (typ) 6.5 dB Band-split 204/258 (pluggable diplex)
Operating output levels Max 110 dBµV
Optical receiver modules available in the following5:
Gain control 0 - 20 dB
Light wavelength: 1290-1610 nm
EQ control 0 - 10 dB
Optical input range (Optical AGC): -6 to +1 dBm
Reverse directive testpoint per input -20 ± 1 dB
Distortion performance (typ) Optical return transmitter module available in the
Hum modulation Max -70 dBc @ 7 A following5:
General Type LASER: DFBI/CWDM/FPI
Class of enclosure IP68 IEC 60529 ed2.1 am1 Light wavelength: 1310/1550 nm
ESD 4 kV IEC 61000-4-2:2008 Optical power: 1 to 4 dBm
Surge protection 6 kV SCTE C62.41 CAT. C3 Status monitoring module DOCSIS compliant5
EMC EN 50083-2:2012 Full remote management5
Safety EN 60728-11:2010
Test points All F-Female Remarks
Operating voltage 20 - 90 VAC (typ) block / trapezium Measurements taken at room temperature
Power req (high/low) 16.5 W / 13.5 W4 1 Including diplex filters, high pass filters and thermal
AC bypass capacity 10 A per port (max) compensator where applicable
Operating temperature range -40 to +65°C 2 -20 dB at 40 MHz - 1.5 dB / octave never worse than
Weight (kg) 2.7 -13 dB
Housing dimensions 195 x 205 x 92 mm 3 5 - 400 MHz: Max 7.5 dB
400 - 950 MHz: Max 7.0 dB
Coaxial connections PG 11 or 5/8” KS
950 - 1218 MHz: Max 7.5 dB
Housing finish Painted conductive chromate finish
4 Without FSK Transponder, add 2.0 W with FSK
Impedance (Ω, typ) 75 Transponder
Equipment approval CE, WEEE and RoHS
5 On roadmap
6 Depending on modules fitted (numbers quoted for RF
configuration)
7 Tilt express between 85 - 1218 MHz
Ordering information
Item Name Article number
DBC-1200 Refer to your sales contact