Professional Documents
Culture Documents
Main Hydraulic System M315C
Main Hydraulic System M315C
Page 1 of 8
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: M315 EXCAVATOR 7ML01027
Configuration: M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine
Systems Operation
M312, M315, M318 and M320 Excavators Hydraulic System
Media Number -SENR6260-03 Publication Date -01/04/2002 Date Updated -26/04/2002
i01025282
S/N - 6ES229-UP
S/N - 6TL410-UP
S/N - 6WL1-UP
S/N - 7ML860-UP
S/N - 8AL1020-UP
S/N - 8SS1-UP
S/N - 9PS1-UP
M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine(SEBP28... Page 2 of 8
Illustration 1 g00543775
Main Pump
M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine(SEBP28... Page 4 of 8
Illustration 2 g00828614
The main hydraulic system is supplied by main pump (22). The main pump activates the following
components:
• Blade cylinders
• Travel motor
Main pump (22) is a variable displacement axial piston pump. Main pump (22) and swing pump (23)
are mechanically connected in series through a flexible coupling.
Illustration 3 g00828511
Typical example
The main pump delivers approximately 260 L/min (69 US gpm) of hydraulic oil at no load. The oil
that is delivered from the main pump enters main control valve (9). The oil is then sent to the
respective cylinders and/or the travel motor. If the hydraulic demand is low, the oil could be returned
to the hydraulic tank.
The main hydraulic pump is load sensing. The pump receives signal pressures in order to regulate the
pump flow. The three following signal pressures are possible:
• Power shift pressure from the main pump proportional reducing valve (PRV)
When all the hydraulic control valves are in neutral, the load sensing pressure is low and the main
pump flow is reduced to a minimum. When one of the hydraulic controls are activated, the load
sensing pressure increases and the pump flow is regulated in proportion to the amount of movement
in the pilot control valve.
The main pump is also controlled by the controller. Input signals from the power mode switch and
the engine speed pickup are sent to the controller. The controller processes these input signals. The
controller then sends a electrical signal to the Proportional Reducing Valve (PRV). The PRV is a
M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine(SEBP28... Page 6 of 8
solenoid operated pressure reducing valve that sends a hydraulic signal to the pump in order to
regulate the pump output. The hydraulic signal from the PRV is called power shift pressure (PS).
PS pressure works with the system pressure in order to regulate the pump flow. A decrease in PS
pressure causes the main pump to destroke at a lower system pressure. An increase in PS pressure
causes the pumps to destroke at a higher system pressure.
Swing Pump
Illustration 4 g00828496
Typical example
The oil is supplied from swing pump (23). The oil activates swing motor (1). Swing pump (23) is a
variable displacement axial piston pump that is mechanically connected to main pump (22). The
swing pump is not self-charging. The pump is supplied oil by an attached charge pump. Swing pump
(23) delivers approximately 112 L/min (30 US gpm) of hydraulic oil at no load.
Pilot Pump
Illustration 5 g00828406
Typical example
M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine(SEBP28... Page 8 of 8
The pilot hydraulic system is driven by gear pump (19). Gear pump (19) is mechanically connected to
the engine timing gear.
• The pilot circuit operates main control valve (9) under the following conditions: operation of
pilot control valves (13) and (15), operation of the travel pedal control valve and the blade pilot
control valve and operation of the travel pedal control valve or blade pilot control valve. Pilot
oil flows to the main control valve through pilot control valves (13) and (15). This pilot oil
flow shifts the stems in the main control valve. This allows the main pump oil to flow to the
required circuits of cylinders (2), (3), and (4) and/or to the travel motor or to the blade cylinder.
• The pilot circuit controls the pump output. The main pump proportional reducing valve in pilot
manifold (20) receives an electrical signal in order to control the pilot system pressure (PS) that
is sent to the main pump regulator. This controls the main pump output flow. The swing pump
proportional reducing valve in pilot manifold (20) receives an electrical signal in order to
control the pilot system pressure to the swing pump regulator. This controls the swing pump
output flow.
• The pilot circuit creates pilot signal pressure in the pilot circuit so the following controls can be
achieved. The pilot circuit activates the Automatic Engine Speed Control (AEC). This causes
an automatic reduction in the engine speed when no hydraulic operation is necessary. The pilot
circuit releases the swing motor brake. The pilot circuit changes the travel speed to the
CREEPER speed. The pilot circuit changes the swing pump flow in order to change the swing
motor direction.
Copyright 1993 - 2021 Caterpillar Inc. Thu Dec 2 09:26:31 UTC+0100 2021
All Rights Reserved.
Private Network For SIS Licensees.