Professional Documents
Culture Documents
Planetaryrollerscrews
Planetaryrollerscrews
Planetaryrollerscrews
SCREWS
INTRODUCTION .............................................................................................................................................................................................3
MOOG PLANETARY ROLLER SCREWS...............................................................................................................................................4
Moog: Always the best technology for you........................................................................................................................................4
Customization................................................................................................................................................................................................6
Testing capabilities.....................................................................................................................................................................................6
This catalog is for users with technical knowledge. To ensure all necessary characteristics for
function and safety of the system, the user has to check the suitability of the products described
herein. The products described in this document are subject to change without notice. In case of
doubt, please contact Moog.
Moog is a registered trademark of Moog Inc. and its subsidiaries. All trademarks as indicated
herein are the property of Moog Inc. and its subsidiaries. For the full disclaimer refer to
www.moog.com/literature/disclaimers.
For the most current information, visit www.moog.com/industrial or contact your local Moog
office.
Screws technologies
Roller Screws Ball Screws Acme screw
Load capacity Very large Large Large
Life span Very long Long Very short
Speed Very fast Average Slow
Acceleration Very large Average Small
Rigidity Very high Average Very high
Impact resistance Very high Average Very high
Heat resistance Very resistant Average Resistant
Space required Very small Average Average
Friction Small Very Small Large
Vibration/noise Very small Small Slightly large
Efficiency 75 to 90% 85 to 95% Around 40%
Ease of maintenance Very easy Average Very low
Environmental load Very small Very small Small
Customizability Very high High Average
The table above shows a comparison of acme screw, ball screw and planetary roller screw actuators as systems deriving
from Moog’s own actuation design experience as well as data provided by other manufacturers.
Load
capacity
Ease of
Life span
maintenance
Roller Screws
Efficiency Speed Ball Screws
Acme screw
Noise Acceleration
Impact
resistance
Moog specialists have optimized this technology in order The main industrial fields that can take advantage of the
to achieve maximum performance compared to other Ultrapower Screws are:
linear actuation solutions, providing also an unrivalled • injection molding and die casting
service life and power density.
• steel industry (casting and rolling)
The Ultrapower Screws combine all the unique features
• presses
of Planetary Roller Screws (High Precision, Speed
and Acceleration rates, reduced axial backlash), with and, more generally, all applications where a suitable
outstanding Load Capacities (up to 50% more than the alternative to hydraulics is needed.
standard products) in a compact envelope, making them
a perfect solution even for designs with extremely small
footprint.
The chart below shows a comparison between the standard roller screws and the ultrapower load capacities.
3500
3000
2500
Load Capacity [kN]
Static
ULTRAPOWER
2000
Static
1500 Standard
Dynamic
1000 ULTRAPOWER
500 Dynamic
Standard
0
60 75 87 100
Pitch Diameter [mm]
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
Table 00C
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
20 8 32 44 37 55 5 42 53 6x6 64 M6 - 55 - 20
10 32 42 37 52 5 42 53 6x6 64 M6 - 55 - 20
21 2 47 83 53 102 5 45 56 6x6 68 M6 26 64 72 18
21 4 51 92 58 112 5 45 56 6x6 68 M6 26 64 72 18
21
5 52 90 59 110 5 45 56 6x6 68 M6 26 64 72 18
21
21 6 54 82 62 103 5 45 56 6x6 68 M6 26 64 72 18
21 8 49 72 57 89 5 45 56 6x6 68 M6 26 64 72 18
10 49 72 57 90 5 45 56 6x6 68 M6 26 64 72 18
23 • 2 37 62 42 76 5 45 56 6x7 67 M6 30 65 - 20
23 4 40 70 46 86 5 45 56 6x7 67 M6 30 65 - 20
23
5 41 69 47 85 5 45 56 6x7 67 M6 30 65 - 20
23
23 6 46 72 53 88 5 45 56 6x7 67 M6 30 65 - 20
23 8 39 56 46 70 5 45 56 6x7 67 M6 30 65 - 20
10 39 57 46 71 5 45 56 6x7 67 M6 30 65 - 20
25 2 64 114 73 139 5 53 70 6x7 84 M6 32 78 90 20
25 4 70 133 80 163 5 53 70 6x7 84 M6 32 78 90 20
25
5 72 133 82 163 5 53 70 6x7 84 M6 32 78 90 20
25
25 6 81 140 92 172 5 53 70 6x7 84 M6 32 78 90 20
Table 00D
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
27 8 48 75 56 93 5 53 68 6x7 83 M6 35 55 69 22
27 10 49 70 57 88 5 53 68 6x7 83 M6 35 55 69 22
27
15 53 66 61 83 5 53 68 6x7 83 M6 35 55 69 22
27
20 43 47 51 60 5 53 68 6x7 83 M6 35 55 69 22
25 41 40 49 51 5 53 68 6x7 83 M6 35 55 69 22
30 2 75 131 86 160 5 64 81 6x9 98 M6 38 85 99 27
30 5 85 164 97 201 5 64 81 6x9 98 M6 38 85 99 27
30
6 96 176 110 215 5 64 81 6x9 98 M6 38 85 99 27
30
30 8 89 158 102 194 5 64 81 6x9 98 M6 38 85 99 27
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
48 15 233 420 266 513 5 100 127 6x13,5 150 M8x1 60 127 145 37
48 20 213 385 243 471 5 100 127 6x13,5 150 M8x1 60 127 145 37
48
25 196 316 227 395 5 100 127 6x13,5 150 M8x1 60 127 145 37
30 193 284 224 354 5 100 127 6x13,5 150 M8x1 60 127 145 37
60 5 282 599 322 733 5 122 150 6x17,5 180 M8x1 71 152 170 45
60 6 322 694 368 849 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
10 309 688 354 841 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
60 15 355 716 405 876 5 122 150 6x17,5 180 M8x1 71 152 170 45
60 20 327 630 373 771 5 122 150 6x17,5 180 M8x1 71 152 170 45
60 25 328 624 375 763 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
30 327 589 374 720 5 122 150 6x17,5 180 M8x1 71 152 170 45
35 334 504 388 630 5 122 150 6x17,5 180 M8x1 71 152 170 45
6 - - 245 705 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
12 - - 270 783 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
64 18 - - 297 736 6 115 150 6x17,5 180 M8x1 75 129 151 45
64 24 - - 274 641 6 115 150 6x17,5 180 M8x1 75 129 151 45
64 30 - - 276 618 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
36 - - 276 587 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
42 - - 292 514 6 115 150 6x17,5 180 M8x1 75 129 151 45
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
87 30 - - 765 1695 5 175 200 12x13,5 220 M8x1 103 220 244 40
87 35 - - 863 1715 5 175 200 12x13,5 220 M8x1 103 220 244 40
40 - - 720 1523 5 175 200 12x13,5 220 M8x1 103 220 244 40
100 15 - - 1042 2727 5 200 245 12x17,5 275 M8x1 112 260 284 55
100 20 - - 969 2530 5 200 245 12x17,5 275 M8x1 112 260 284 55
100
25 - - 988 2470 5 200 245 12x17,5 275 M8x1 112 260 284 55
100
100 30 - - 999 2381 5 200 245 12x17,5 275 M8x1 112 260 284 55
100 35 - - 1133 2441 5 200 245 12x17,5 275 M8x1 112 260 284 55
40 - - 1007 2181 5 200 245 12x17,5 275 M8x1 112 260 284 55
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
20 8 20 22 23 27 5 42 3 - 20x4 43,5 55 55
10 20 21 23 26 5 42 3 - 20x4 43,5 55 55
21 2 29 42 34 51 5 45 5 26 20x5 47 64 72
21 4 32 46 37 56 5 45 5 26 20x5 47 64 72
21
5 33 45 37 55 5 45 5 26 20x5 47 64 72
21
21 6 34 41 39 51 5 45 5 26 20x5 47 64 72
21 8 31 36 36 45 5 45 5 26 20x5 47 64 72
10 31 36 36 45 5 45 5 26 20x5 47 64 72
23 • 2 23 31 27 38 5 45 4 30 20x5 47 65 -
23 4 25 35 29 43 5 45 4 30 20x5 47 65 -
23
5 26 35 30 42 5 45 4 30 20x5 47 65 -
23
23 6 29 36 33 44 5 45 4 30 20x5 47 65 -
23 8 25 28 29 35 5 45 4 30 20x5 47 65 -
10 25 28 29 36 5 45 4 30 20x5 47 65 -
25 2 40 57 46 69 5 53 5 32 25x6 55,5 78 90
25 4 44 67 50 81 5 53 5 32 25x6 55,5 78 90
25
5 45 67 52 82 5 53 5 32 25x6 55,5 78 90
25
6 51 70 58 86 5 53 5 32 25x6 55,5 78 90
25
25 8 43 55 50 69 5 53 5 32 25x6 55,5 78 90
25 10 44 52 50 65 5 53 5 32 25x6 55,5 78 90
25
15 47 48 54 60 5 53 5 32 25x6 55,5 78 90
25
20 42 38 48 48 5 53 5 32 25x6 55,5 78 90
25 36 29 43 37 5 53 5 32 25x6 55,5 78 90
Table 0CC
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
27 8 31 37 35 47 5 53 5 32 20x5 55 55 69
27 10 31 35 36 44 5 53 5 32 20x5 55 55 69
27
15 33 33 39 41 5 53 5 32 20x5 55 55 69
27
20 27 23 32 30 5 53 5 32 20x5 55 55 69
25 26 20 31 26 5 53 5 32 20x5 55 55 69
30 2 47 65 54 80 5 64 5 38 32x6 66,5 85 99
30 5 54 82 61 100 5 64 5 38 32x6 66,5 85 99
30
6 61 88 69 108 5 64 5 38 32x6 66,5 85 99
30
30 8 56 79 64 97 5 64 5 38 32x6 66,5 85 99
30 10 57 75 65 92 5 64 5 38 32x6 66,5 85 99
30 15 57 65 67 82 5 64 5 38 32x6 66,5 85 99
30
20 51 53 60 66 5 64 5 38 32x6 66,5 85 99
30
25 50 45 58 57 5 64 5 38 32x6 66,5 85 99
30 44 35 52 45 5 64 5 38 32x6 66,5 85 99
36 • 6 - - 65 137 6 68 5 45 25x5 70 80 96
36 9 - - 75 142 6 68 5 45 25x5 70 80 96
36
12 - - 66 116 6 68 5 45 25x5 70 80 96
36
36 18 - - 74 115 6 68 5 45 25x5 70 80 96
36 24 - - 63 85 6 68 5 45 25x5 70 80 96
30 - - 62 73 6 68 5 45 25x5 70 80 96
39 2 65 86 75 105 5 80 7 50 40x8 83 100 116
39 5 75 120 86 147 5 80 7 50 40x8 83 100 116
39 6 85 132 98 162 5 80 7 50 40x8 83 100 116
39
10 81 120 92 146 5 80 7 50 40x8 83 100 116
39
15 90 113 103 139 5 80 7 50 40x8 83 100 116
39
393 20 76 92 88 115 5 80 7 50 40x8 83 100 116
25 75 81 87 101 5 80 7 50 40x8 83 100 116
30 73 72 85 90 5 80 7 50 40x8 83 100 116
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
20 8 20 22 23 27 5 42 53 6x6 64 M6 - 55 - 20
10 20 21 23 26 5 42 53 6x6 64 M6 - 55 - 20
21 2 29 42 34 51 5 45 56 6x6 68 M6 26 64 72 18
21 4 32 46 37 56 5 45 56 6x6 68 M6 26 64 72 18
21
5 33 45 37 55 5 45 56 6x6 68 M6 26 64 72 18
21
21 6 34 41 39 51 5 45 56 6x6 68 M6 26 64 72 18
21 8 31 36 36 45 5 45 56 6x6 68 M6 26 64 72 18
10 31 36 36 45 5 45 56 6x6 68 M6 26 64 72 18
23 • 2 23 31 27 38 5 45 56 6x7 67 M6 30 65 - 20
23 4 25 35 29 43 5 45 56 6x7 67 M6 30 65 - 20
23
5 26 35 30 42 5 45 56 6x7 67 M6 30 65 - 20
23
23 6 29 36 33 44 5 45 56 6x7 67 M6 30 65 - 20
23 8 25 28 29 35 5 45 56 6x7 67 M6 30 65 - 20
10 25 28 29 36 5 45 56 6x7 67 M6 30 65 - 20
25 2 40 57 46 69 5 53 70 6x7 84 M6 32 78 90 20
25 4 44 67 50 81 5 53 70 6x7 84 M6 32 78 90 20
25
5 45 67 52 82 5 53 70 6x7 84 M6 32 78 90 20
25
25 6 51 70 58 86 5 53 70 6x7 84 M6 32 78 90 20
25 8 43 55 50 69 5 53 70 6x7 84 M6 32 78 90 20
25 10 44 52 50 65 5 53 70 6x7 84 M6 32 78 90 20
25
15 47 48 54 60 5 53 70 6x7 84 M6 32 78 90 20
25
20 42 38 48 48 5 53 70 6x7 84 M6 32 78 90 20
25 36 29 43 37 5 53 70 6x7 84 M6 32 78 90 20
Table 0DD
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
27 8 31 37 35 47 5 53 68 6x7 83 M6 35 55 69 22
27 10 31 35 36 44 5 53 68 6x7 83 M6 35 55 69 22
27
15 33 33 39 41 5 53 68 6x7 83 M6 35 55 69 22
27
20 27 23 32 30 5 53 68 6x7 83 M6 35 55 69 22
25 26 20 31 26 5 53 68 6x7 83 M6 35 55 69 22
30 2 47 65 54 80 5 64 81 6x9 98 M6 38 85 99 27
30 5 54 82 61 100 5 64 81 6x9 98 M6 38 85 99 27
30
6 61 88 69 108 5 64 81 6x9 98 M6 38 85 99 27
30
30 8 56 79 64 97 5 64 81 6x9 98 M6 38 85 99 27
30 10 57 75 65 92 5 64 81 6x9 98 M6 38 85 99 27
30 15 57 65 67 82 5 64 81 6x9 98 M6 38 85 99 27
30
20 51 53 60 66 5 64 81 6x9 98 M6 38 85 99 27
30
25 50 45 58 57 5 64 81 6x9 98 M6 38 85 99 27
30 44 35 52 45 5 64 81 6x9 98 M6 38 85 99 27
36 • 6 - - 65 137 6 68 85 6x9 102 M6 45 80 96 27
36 9 - - 75 142 6 68 85 6x9 102 M6 45 80 96 27
36
12 - - 66 116 6 68 85 6x9 102 M6 45 80 96 27
36
36 18 - - 74 115 6 68 85 6x9 102 M6 45 80 96 27
36 24 - - 63 85 6 68 85 6x9 102 M6 45 80 96 27
30 - - 62 73 6 68 85 6x9 102 M6 45 80 96 27
39 2 65 86 75 105 5 80 102 6x11 124 M6 50 100 116 33
39 5 75 120 86 147 5 80 102 6x11 124 M6 50 100 116 33
39
6 85 132 98 162 5 80 102 6x11 124 M6 50 100 116 33
39
10 81 120 92 146 5 80 102 6x11 124 M6 50 100 116 33
39
39 15 90 113 103 139 5 80 102 6x11 124 M6 50 100 116 33
399 20 76 92 88 115 5 80 102 6x11 124 M6 50 100 116 33
25 75 81 87 101 5 80 102 6x11 124 M6 50 100 116 33
30 73 72 85 90 5 80 102 6x11 124 M6 50 100 116 33
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
Standard number of rollers
2)
Maximum number of rollers
3)
Custom dimension available upon request
4)
With D0 < 21 mm wipers within nut length
[g6] [h12]
mm mm kN kN kN kN Starts mm mm mm mm mm mm mm
44 • 6 - - 75 160 6 80 102 6x11 124 M6 56 90 106 33
44 8 - - 78 164 6 80 102 6x11 124 M6 56 90 106 33
44
12 - - 77 146 6 80 102 6x11 124 M6 56 90 106 33
44
18 - - 87 136 6 80 102 6x11 124 M6 56 90 106 33
44
444 24 - - 76 115 6 80 102 6x11 124 M6 56 90 106 33
30 - - 75 100 6 80 102 6x11 124 M6 56 90 106 33
36 - - 74 88 6 80 102 6x11 124 M6 56 90 106 33
48 5 119 198 136 242 5 100 127 6x13,5 150 M8x1 60 127 145 37
48 6 135 224 155 274 5 100 127 6x13,5 150 M8x1 60 127 145 37
48
8 126 212 145 260 5 100 127 6x13,5 150 M8x1 60 127 145 37
48
10 129 212 148 259 5 100 127 6x13,5 150 M8x1 60 127 145 37
48
4848 15 147 210 168 256 5 100 127 6x13,5 150 M8x1 60 127 145 37
8 20 134 193 153 235 5 100 127 6x13,5 150 M8x1 60 127 145 37
25 123 158 143 198 5 100 127 6x13,5 150 M8x1 60 127 145 37
30 122 142 141 177 5 100 127 6x13,5 150 M8x1 60 127 145 37
60 5 177 300 203 366 5 122 150 6x17,5 180 M8x1 71 152 170 45
60 6 203 347 232 424 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
10 195 344 223 421 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
15 223 358 255 438 5 122 150 6x17,5 180 M8x1 71 152 170 45
60
60 20 206 315 235 385 5 122 150 6x17,5 180 M8x1 71 152 170 45
6060 25 207 312 236 381 5 122 150 6x17,5 180 M8x1 71 152 170 45
30 206 295 235 360 5 122 150 6x17,5 180 M8x1 71 152 170 45
35 211 252 244 315 5 122 150 6x17,5 180 M8x1 71 152 170 45
64 6 - - 154 352 6 115 150 6x17,5 180 M8x1 75 129 151 45
64 12 - - 170 392 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
18 - - 187 368 6 115 150 6x17,5 180 M8x1 75 129 151 45
64
24 - - 173 320 6 115 150 6x17,5 180 M8x1 75 129 151 45
4
30 - - 174 309 6 115 150 6x17,5 180 M8x1 75 129 151 45
64 36 - - 174 293 6 115 150 6x17,5 180 M8x1 75 129 151 45
42 - - 184 257 6 115 150 6x17,5 180 M8x1 75 129 151 45
LEGEND of SYMBOLS
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
On request dimension can be
customized
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
NOTES
1)
ustom
C dimension available upon
request
2)
n request the flange position can be
O
shifted axially to the middle of nut
87 10 903 2543 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 15 1052 2875 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 20 976 2630 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 25 992 2533 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 30 1000 2416 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 35 1128 2444 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
87 40 940 2171 5 175 200 12x13,5 220 M8x1 103 245 269 40 35 40
100 15 1303 3695 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
100 20 1213 3427 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
100 25 1236 3345 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
100 30 1250 3225 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
100 35 1417 3306 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
100 40 1260 2954 5 200 224 12x17,5 245 M8x1 112 280 304 50 40 40
For approximate Axial Stiffness of Nut use the formula RN = f N · Fax1/3 , where Fax is the external axial load applied
For approximate Axial Stiffness of Shaft use the formula R S = f S / LS , where LS is the length of the threaded shaft
mS mN JS JN - N JN - S fS fN Designation
D0 D1 D2 D3 D4 D5 L1 L2 L3 L4 L5 L6 A B L7
[ h6 ] [ h7 ] [ 6g ] [ h11 ] [ js12 ] [ js12 ] [ N9 ] [ +0,1/0 ] [ +0,5/0 ]
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
15 10 16,5 8 M10x1 8 98 7 28 15 2 1,5 3 1,8 25
20 15 25 12 M15x1 13 140 11 39 22 2 2 5 3 35
21
23
D0 D1 D2 L1 L2 L3 C
[ js7 ] [ h12 ] [ js12 ] [ H13 ] [ H11 ]
mm mm mm mm mm mm mm
15 10 9,6 11 1.1 9,1 0,5
60 50 47 27 2.15 22,15 1
64
75 60 57 30 2.15 24,15 2
“X” Centering hole - UNI 6411 “W” Threaded hole - UNI 9321 “Z” Hexagon socket
D0 W LW Z LZ
mm mm mm mm mm
15 - - - - -
20 - M4 10 3 6
21
23
25
27
30 - M6 16 5 10
36
39 - M8 19 8 15
44
48
60 - M10 22 10 20
64
75
87 - M16 36 16 35
100
ORDERING CODE
To order a Roller Screw choose the various options by filling in the box-card on this page. Use the Customization Tables
displayed in next page as needed (Table A is required). Please provide any additional documentation (drawings or
technical data) to our sales department.
NUT TYPE
00C Single cylindrical - standard backlash
00D Single flanged - standard backlash
0RC Single cylindrical - no backlash/reduced backlash
0RD Single flanged - no backlash/reduced backlash
0CC Split cylindrical - with preload
0DD Split flanged - with preload
UPC Ultra power -single cylindrical - standard backlash
UPD Ultra power - single flanged - standard backlash
ROLLERSCREW NOMINAL DIAMETER [mm]
Default diameter selection: From 15 up to 100
ROLLERSCREW LEAD [mm]
Default lead selection: From 2 up to 42
ROLLERSCREW LEAD DIRECTION
R Right hand
L Left hand
WIPERS
A Standard wipers
B Wipers within nut
C No wipers
ROLLERSCREW ACCURACY CLASS
3 Precision class ISO3
5 Precision class ISO5
NUMBER OF ROLLERS
MAX Maximum number of rollers
MIN Minimum number of rollers
“X” Centering hole - UNI 6411 “W” Threaded hole - UNI 9321 “Z” Hexagon socket