Professional Documents
Culture Documents
Button Hole Machine - LBH-1790
Button Hole Machine - LBH-1790
Button Hole Machine - LBH-1790
LBH-1790
INSTRUCTION MANUAL
CONTENTS
蠢 . IMPORTANT SAFETY INSTRUCTIONS ....................................................................... 1
蠡 . SPECIFICATIONS ......................................................................................................... 1
1. Subclass ................................................................................................................................................ 1
2. Specifications ........................................................................................................................................ 1
3. Standard sewing shape list .................................................................................................................. 2
4. Configuration ........................................................................................................................................ 3
蠱 . INSTALLATION ............................................................................................................. 4
蠶 . PREPARATION BEFORE OPERATION ..................................................................... 12
1. Lubrioation .......................................................................................................................................... 12
2. Inserting the needle ............................................................................................................................ 12
3. Threading the needle-thread .............................................................................................................. 13
4. Threading the bobbin case ................................................................................................................ 13
5. Adjusting the bobbin thread tension ................................................................................................ 14
6. Installation of bobbin case ................................................................................................................. 14
7. Installing the knife .............................................................................................................................. 15
蠹 . OPERATION OF THE SEWING MACHINE ................................................................. 16
1. Explanation of the operation panel switch ....................................................................................... 16
2. Basic operation of the sewing machine ........................................................................................... 18
3. How to use the pedal .......................................................................................................................... 18
4. Input of the presser type .................................................................................................................... 20
5. Performing pattern selection ............................................................................................................. 21
6. Changing needle thread tension ....................................................................................................... 22
7. Performing re-sewing ......................................................................................................................... 23
8. Winding bobbin thread ....................................................................................................................... 24
9. Using the counter ............................................................................................................................... 25
10. Using the initial value pattern ............................................................................................................ 26
11. Changing sewing data ........................................................................................................................ 27
12. Method of setting sewing data with/without edit ............................................................................. 28
13. Sewing data list ................................................................................................................................... 29
14. Copying sewing pattern ..................................................................................................................... 35
15. Using pattern register key .................................................................................................................. 36
16. Using parameter register key ............................................................................................................ 37
17. Performing continuous stitching ....................................................................................................... 38
18. Performing cycle stitching ................................................................................................................. 40
19. Explanation of plural motions of knife .............................................................................................. 42
20. Method of changing memory switch data ........................................................................................ 43
21. Memory switch data list ..................................................................................................................... 44
蠧 . MAINTENANCE .......................................................................................................... 48
1. Adjusting the needle-to-hook relation .............................................................................................. 48
2. Adjusting the needle thread trimmer ................................................................................................ 49
3. Adjusting the presser bar pressure .................................................................................................. 50
4. Adjustment of the bobbin presser unit ............................................................................................. 50
5. Thread tension .................................................................................................................................... 52
6. Cleaning the filter ................................................................................................................................ 52
7. Replacing the fuse .............................................................................................................................. 52
蠻 . GAUGE COMPONENTS ............................................................................................. 53
1. Cloth cutting knife .............................................................................................................................. 53
2. Throat plate ......................................................................................................................................... 53
3. Presser ................................................................................................................................................. 53
衄 . ERROR CODE LIST .................................................................................................... 54
衂 . TROUBLES AND CORRECTIVE MEASURES ........................................................... 57
衒 . DRAWING OF THE TABLE ......................................................................................... 59
衙 . INITIAL VALUE DATA FOR EACH SHAPE TABLE .................................................... 60
i
1. IMPORTANT SAFETY INSTRUCTIONS
1) Never operate the machine unless the oiling tank has been properly lubricated.
2) Be sure to remove any dust from the hook or bobbin thread cutting knife section at the end of the day,
and check the amount of oil remaining.
3) Be sure to return the activating pedal to the home position after the machine has started to run.
4) A safety switch is installed so that this sewing machine can not be operated in the state that the machine
head is tilted. When operating this sewing machine, turn the power switch ON after setting the sewing
machine to the bed base properly.
2. SPECIFICATIONS
1. Subclass
Computer-controlled, high-speed, lockstitch buttonholing machine, LBH-1790, has the subclass machines below.
Subclass S K
Major Buttonholing of cloth Buttonholing of knits
application such as men’s shirts, such as knitted
blouses, work uniforms, underwear, sweaters,
ladies' wear, etc. cardigans, jersey, etc.
Buttonholing
Standard : Max. 5 mm
size Special type part : Max. 10 mm
2. Specifications
Sewing speed Standard speed : 3,600 rpm (Max. : 4,200 rpm) (Max. : 3,300 rpm when dry hook is used)
Needle DPX5 #11J to #14J
Hook DP type full-rotary hook
Needle rocking drive Drive by stepping motor
method
Feed drive method Drive by stepping motor
Presser lifting drive Drive by stepping motor
method
Lift of presser foot 14 mm (Optional setting available) Max. : 17 mm (At the time of needle up by reverse run)
Cloth cutting knife By double-acting solenoid drive
drive method
Standard sewing 30 kinds
shape
Number of patterns 99 patterns
stored in memory
Motor used Single phase 220/230/240 V, 3-phase 200 to 240 V, 1000 VA
Noise Workplace-related noise at sewing speed
n = 4,000 min–1 : LPA ≦ 83 dB(A)
Noise measurement according to DIN 45635-48-A-1.
−1−
3. Standard sewing shape list
(5) Radial straight bar- (6) Radial taper bar-tacking
(1) Square type (2) Round type (3) Radial square type (4) Radial type
tacking type type
(13) Semilunar square (14) Semilunar straight (15) Semilunar taper bar- (16) Eyelet semilunar
(17) Eyelet round type (18) Square radial type
type bar-tacking type tacking type type
(19) Square semilunar (21) Square straight bar- (22) Square taper bar- (23) Radial semilunar
(20) Square round type (24) Radial round type
type tacking type tacking type type
−2−
4. Configuration
−3−
3. INSTALLATION
WARNING :
To prevent possible accidents caused by the fall of the sewing machine, perform the work by two persons
or more when the machine is moved.
!1
u
t
i w
!0
Adjust the positions of the pedals so that connecting rods i and control box w do not
come in contact with each other.
−4−
(2) Connecting the power source cord
• Voltage specifications
Power source specifications are indicated on the
voltage indication seal. (3-phase type only)
For other type machines, power source specifications
are indicated on the voltage caution seal and the
rating label.
Voltage caution seal Connect the cord in accordance with the
specifications.
Rating label
Table
AC200 V
Green/Yellow Brown AC220 V
Light AC230 V
Control box blue
Plug AC240 V
Green/Yellow Green/
Yellow GND
Brown Brown Power switch
Power source cord
Table
White
Green / AC200 V
Yellow Black AC220 V
Control box
Plug AC240 V
Red
Green/Yellow
Green / GND
Black Black Red Yellow
Red
−5−
(3) Changing the voltage of 100 / 200V
WARNING :
To prevent personal injuries caused by electric shock hazards or abrupt start of the sewing
machine, carry out the work after turning OFF the power switch and a lapse of 5 minutes or
more. To prevent accidents caused by unaccustomed work or electric shock, request the electric
expert or engineer of our dealers when adjusting the electrical components.
It is adaptable to the voltage of single phase 100V to 120V/3-phase 200V to 240V by changing the
voltage changeover connector mounted on FLT p.c.b.
(Caution) When the changing procedure is wrong, the control box will be broken. So, be very
careful.
Changing procedure of the changeover connector
1. Turn OFF the power source with the power
switch after confirming that the sewing machine
has stopped.
2. Draw out the power cord from the power plug
socket after confirming that the power switch is
turned OFF. Then wait for five minutes or more.
3. Remove the front cover.
4. Remove four screws fixing the rear cover of the
control box and slowly open the rear cover.
A. In case of using with 3-phase 200V to 240V
• Changing the changeover connector
1 Connect to 200V the 100/200V changeover
connector of FLT p.c.b. 1 located on the side
A of the Box Side of the control box.
• Connect the crimp style terminal of AC input cord
to the power plug as shown in the figure.
B. In case of using with single phase 100V to 120V
• Changing the changeover connector
(Plug side)
Connect to 100V the 100/200V changeover
WHITE WHITE connector of FLT p.c.b. 1 located on the side
BLACK BLACK of the Box Side of the control box.
RED RED • Connect the crimp style terminal of AC input cord
to the power plug as shown in the figure.
GREEN/ GREEN/ (Caution) Securely perform the insulation
YELLOW YELLOW treatment to the red terminal which
is not used with insulation tape or
B the like.
(When the insulation is insufficient,
there is a danger of electric shock or
leakage current.)
(Plug side) C. In case of using with single phase 200V to 240V
WHITE WHITE • Changing the changeover connector
BLACK BLACK Connect to 200V the 100/200V changeover
RED connector of FLT p.c.b. 1 located on the side
RED
of the Box Side of the control box.
GREEN/ GREEN/ • Connect the crimp style terminal of AC input cord
YELLOW YELLOW to the power plug as shown in the figure.
(Caution) Securely perform the insulation
treatment to the red terminal which is
C not used with insulation tape or the
like.
(When the insulation is insufficient,
there is a danger of electric shock or
leakage current.)
(Plug side)
WHITE WHITE
5. Check that the change has been performed without
BLACK BLACK
fail before closing the rear cover.
6. Be careful that the cord is not pinched between
RED RED
the rear cover and the control box main unit. Close
GREEN/ GREEN/ the rear cover while pressing the lower side of rear
YELLOW YELLOW cover, and tighten four screws.
−6−
(4) Installing the sewing machine main unit
WARNING :
To prevent possible accidents caused by the
fall of the sewing machine, perform the work
by two persons or more when the machine
is moved.
w-1 (rubber)
e w-2
(metal)
−7−
(6) Connecting the safety switch connector
Cord clamp
−8−
(9) Connecting the cords
Perform the connection of the cords as shown in the figure below.
CN14
CN16
SDC circuit
CN16 CN14
board
CN37
CN38
CN37
CN42
CN38 CN39
CN39 Operation panel
CN41
CN41
CN44
CN34
CN34
MAIN circuit
board Electric bobbin winding device (optional)
CN42
CN44
−9−
(10) Managing the cord
1) Slowly tilting the sewing machine, check that the cords are not forcibly pulled.
2) Fix the cords with cord setting plate 1 as shown in the figure.
When you tilt the sewing machine, make sure that the sewing machine head support
bar 2 is placed on the table.
Be sure to install and use eye protection cover 1 and use the sewing machine.
Operator
Operator
− 10 −
(12) Fixing the temporary stop switch
The temporary stop switch has been in the state as shown in figure A at the time of delivery.
Loosen setscrew q and set the switch in the state as shown in figure B, and fix it with setscrew q together
with setscrew w supplied with the machine.
\ q
B
A
− 11 −
4. PREPARATION BEFORE OPERATION
1. Lubrioation
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
we
r t
e
q
w
Decrease
Oil amount
Increase
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
Hold needle with its recessed part facing toward the operator side A,
insert the needle fully into the needle clamping hole, and tighten needle
setscrew q. Use a DPx5-(#11J, #14J).
− 12 −
3. Threading the needle-thread
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
u q
Cotton thread, spun thread Synthetic filament thread
y
i
r
e
t
o
!1 !0
!2
w r
e
r
Rotating direction of bobbin and threading
1) Fit the bobbin so that it rotates in the direction of the arrow.
2) Pass the thread through thread slit q, then through under the tension spring w, again through thread
slit e, and pull the thread from r.
3) Threading at r for purl stitching is different from that for whip stitching. So, be careful.
− 13 −
5. Adjusting the bobbin thread tension
w
q
Adjust the bobbin thread tension as given below when the bobbin thread is pulled up at the position where
thread slit q of bobbin case comes up.
To such an extent that bobbin case quietly comes down when holding
Purl stitch 0.05 to 0.15N thread end coming from bobbin case and shaking it quietly up and
down.
To such an extent that bobbin case barely comes down when holding
Whip stitch 0.15 to 0.3N thread end coming from bobbin case and shaking it somewhat
strongly.
Turning tension adjust screw w clockwise will increase bobbin thread tension, and turning it counterclockwise
will decrease the tension.
Adjust the bobbin thread tension to lower for synthetic filament thread, and to higher for spun thread. The
thread tension is higher by approximately 0.05N when the bobbin case is set to the hook since idle-prevention
spring is provided.
When bobbin thread tension is adjusted, check the needle thread tension setting of the
memory switch. (See P.44.)
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
− 14 −
7. Installing the knife
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
− 15 −
5. OPERATION OF THE SEWING MACHINE
w e r t y
q !0
!1
!6
u !7
i !8
o
!9
!2
@0
!3
!4 @1
!5 @2
@7
@3
@8
@4 @5 @6 #0
@9
− 16 −
No. NAME FUNCTION No. NAME FUNCTION
q LCD display Various data such as pattern No., !6 OVEREDGING This key selects overedging width
shape, etc. are displayed. WIDTH key display.
w READY key Press this key when starting sewing. !7 BAR-TACKING This key selects left side of bar-tacking
Every time this key is pressed, change- WIDTH, LEFT key width compensation display.
over of sewing ready set state and data
set state can be performed.
e RESET key Press this key when releasing error, !8 BAR-TACKING This key selects right side of bar-tacking
travelling the feed mechanism to its WIDTH, RIGHT width compensation display.
initial position, counter resetting, etc. key
r MODE key Press this key when changing data of !9 CLOTH CUT This key selects cloth cut length display.
the memory switches. LENGTH key
t PRESSER key This key lifts or lowers the presser. When @0 CLEARANCE key This key selects clearance display.
the presser goes up, the needle bar travels
to the origin and when it comes down, the
needle bar travels to the right.
y WINDER key This key is pressed when performing @1 KNIFE GROOVE This key selects knife groove width,
bobbin winding. WIDTH, RIGHT right compensation display.
key
u PATTERN NO. key This key selects pattern No. display. @2 KNIFE GROOVE This key selects knife groove width, left
WIDTH, LEFT key compensation display.
i DATA key This key selects data display. @3 COPY key Press this key when copying pattern.
o COUNTER key Thus key selects counter display. @4 PRESSER This key selects presser type.
SELECTION key
!0 ITEM SELECTION This key selects pattern No., data No., @5 FORWARD key This key makes the feed mechanism
key etc. travel forward stitch by stitch.
!1 DATA CHANGE This key changes various data. @6 BACKWARD key This key makes the feed mechanism
key travel backward stitch by stitch.
!2 SHAPE key This key selects shape display. @7 PATTERN This is a short cut key that pattern registration
REGISTRATION key is available. Registration of shortcut to setting
display of an optional pattern is possible.
For the setting procedure, see P.36.
!3 THREAD TENSION AT This key selects thread tension at @8 PARAMETER This is a short cut key that parameter registration
PARALLEL SECTION key parallel section display. REGISTRATION key is available. Registration of shortcut to setting
display of an optional pattern, sewing
parameter or adjustment data is possible. For
the setting procedure, see P.37.
!4 THREAD TENSION AT This key selects thread tension at bar- @9 Speed variable Speed increases when this is lifted
BAR-TACKING SECTION tacking section display. resister upward and decreases when this is
key lowered downward.
!5 PITCH key This key selects pitch of parallel #0 LCDadjustment Light and shade of LCD display can be
section. variable rsistor adjusted.
− 17 −
2. Basic operation of the sewing machine
1) Turn ON the power switch.
First, check that presser type A which has been w
set is the same as that of the presser actually
mounted. For checking and setting procedures,
refer to 4. Inputting the presser type.
4) Start sewing.
Set the sewing product to the presser portion, and operate the pedal to start the sewing machine, and
sewing starts. When you purchase the sewing machine, 2-pedal type has been set. However, pedal operating
procedure can be selected from among three ones. Select the operating procedure you desire and use the
sewing machine. → 3. How to use the pedal
!0 !1
− 18 −
(2) Explanation of pedal motion
5) End of sewing
(Presser automatically goes up to
Maximum position q.)
Cloth e
− 19 −
4. Input of the presser type
(1) Setting procedure of the presser type
@4
Set the number in the frame of engraved part number of presser to the type of presser.
− 20 −
5. Performing pattern selection
(1) Selection from the pattern selection screen
This sewing machine can register the pattern No. you desire with the register switch. When the pattern is
registered once, pattern selection can be performed by pressing only the switch.
/ Refer to 15. Using pattern register key.
− 21 −
6. Changing needle thread tension
Needle thread tension can be changed while performing trial sewing since the data related to the needle
thread tension can be set by the sewing mode as well. B
− 22 −
7. Performing re-sewing
When stop switch A is pressed during sewing
operation, the sewing machine interrupts sewing
and stops. At this time, error display screen B is
displayed to inform that the stop switch is pressed.
− 23 −
8. Winding bobbin thread
(1) Winding the bobbin
r
3) Start bobbin winding.
Depress the right-hand side pedal, and the sewing w e
machine rotates and starts winding bobbin thread.
− 24 −
9. Using the counter
(1) Setting procedure of the counter value w e D
− 25 −
10. Using the initial value pattern
This sewing machine has the initial value to perform the optimum sewing for the sewing shapes (30 shapes).
/ Refer to -. INITIAL VALUE DATA FOR EACH SHAPE TABLE.
When creating sewing data newly, it is convenient to create it by copying the initial value pattern.
− 26 −
11. Changing sewing data
(1) Initial sewing data at the time of your purchase
Patterns from 1 to 10 have been already registered at the time of your purchase. Initial values of the square
type, the cloth cutting length of which only is different from each other, have been inputted in the sewing
data. / Refer to -. INITIAL VALUE DATA FOR EACH SHAPE TABLE.
Pattern No. Cloth cutting length
1 6.40mm (1/4”)
2 9.50mm (3/8”)
3 11.1mm (7/16”)
4 12.7mm (1/2”)
5 14.30mm (9/16”)
6 15.90mm (5/8”)
7 17.50mm (11/16”)
8 19.10mm (3/4”)
9 22.20mm (7/8”)
10 25.40mm (1”)
− 27 −
12. Method of setting sewing data with/without edit
This sewing machine has been set so as not to be capable of editing sewing data items which are less
frequently used at the time of your purchase. When you desire to set the data more closely in accordance
with the sewing products, set the sewing data item to the edit possible state and use the machine.
For the setting of sewing data with/without edit, when S52, right parallel section tension is set to without edit,
sewing is performed with the data of S51 left parallel section tension. When S56, 2nd bar-tacking tension is
set to without edit, sewing is performed with the data of S55, 1st bar-tacking section.
When the sewing data items other than the above ones are set to without edit, the data to be referred are the
initial value data.
− 28 −
13. Sewing data list
☆ Sewing data are those that can be inputted to 99 patterns from pattern 1 to 99 and can be inputted to
each pattern. The sewing machine has been set in the state that the data which is necessary to set
“With/without edit” cannot be selected at the time of your purchase. Change over the function to “With
edit” if necessary for the use. / Refer to 12. Method of setting sewing data with/without edit.
No. Item Setting range Edit unit Remarks
S01 Sewing shape 1 to 30 1 –
This item selects the shape from among the sewing shapes of 30
different kinds which the sewing machine has.
− 29 −
No. Item Setting range Edit unit Remarks
S10 Compensation of bar-tacking width, right -1.00 to 1.00 0.05mm –
This item adjusts right side outer shape of bar-tacking
section in terms of overedging section.
Top of Bottom of Bottom of
square square type straight bar-
type tacking
: With : Without
− 30 −
NO. Item Setting range Edit unit Remarks
S22 1st clearance 0.0 to 4.0 0.1mm –
This item sets the clearance between 1st bar-tacking
and knife groove. This item is applied to all shapes.
: With basting
: Without basting
(Setting of number of times)
S41 Compensation of left side position of basting -2.0 to 2.0 0.1mm *2, *3
This item sets the amount to move the sewing reference
position of basting from the center of left overedging to
the right or left.
− 31 −
NO. Item Setting range Edit unit Remarks
S42 Compensation of right side position of -2.0 to 2.0 0.1mm *2, *3
basting
This item sets the amount to move the sewing
reference position of basting from the center of right
overedging to the right or left.
− 32 −
NO. Item Setting range Edit unit Remarks
S59 ACT timing adjustment at the start of 1st bar- -5 to 5 1 stitch *2
tacking
This item adjusts needle thread tension output start
timing at 1st bar-tacking section.
S63 Sewing pitch of tie stitching at the start of 0.00 to 0.70 0.05mm *2
sewing
This item sets sewing pitch pf tie stitching at the start
of sewing.
S64 Tie stitching width at the start of sewing 0.0 to 3.0 0.1mm –
This item sets tie stitching width at the start of sewing.
S67 Tie stitching width at the end of sewing 0.1 to 1.5 0.1mm –
This item sets tie stitching width at the end of sewing.
− 33 −
NO. Item Setting range Edit unit Remarks
S81 Knife motion – – –
This item sets "With/without motion" of normal cloth cutting knife.
− 34 −
14. Copying sewing pattern
Data of pattern No. which has been already registered can be copied to pattern No. which has not been
used. Overwriting copy of the pattern is prohibited. When you desire to overwrite, perform it after erasing the
pattern once.
5) Start copying.
Press READY key w to start copying. After
two seconds, the pattern No. which is created
by copying returns to the input screen in the state
of being selected.
Press RESET key e , and the screen returns
to the former one without copying.
* In addition, cycle data and continuous stitching data can be copied by the same method.
− 35 −
15. Using pattern register key
Register pattern Nos. which are frequently used with the pattern register key and use them.
Patterns which have been registered can be selected by pressing only the pattern register key under the
input mode.
4) Start register.
Press READY key w to start register and the
screen returns to the input screen after two
seconds.
Press RESET key e , and the screen returns
to the former one without registering.
− 36 −
16. Using parameter register key
Register parameters which are frequently used with parameter register key and use them.
Parameters which have been registered can be selected by pressing only the parameter register key under
the input mode. In addition, this key can use the same method as that of 15. Using pattern register key
since this key can register not only the parameters but also pattern Nos.
w e
(1) Method of register
4) Start register.
Press READY key w to start register and the screen returns to the input screen after two seconds.
Press RESET key e , and the screen returns to the former one without registering.
− 37 −
17. Performing continuous stitching
This sewing machine can perform continuous stitching which is capable of continuously sewing plural sewing
pattern data without lifting the presser foot. It is possible to automatically sew up to maximum 6 shapes in
one cycle.
In addition, registration of as many as 20 data can be performed. Copy and use the data to fill the needs.
/ Refer to 14. Copying sewing pattern
* It is necessary to change the parts from the state at tht time of your purchase according to the
setting conditions.
4) Perform sewing.
Press READY key w in the state that
continuous stitching data is selected, and the back-
light of LCD display q shows green and it is
possible to sew. Continuous stitching data No. 1
only has been registered at the time of your
purchase. However, sewing status cannot be
obtained since the sewing pattern has not been
inputted. Perform inputting of sewing pattern
referring to 2) Method of editing continuous
stitching data on the next page.
− 38 −
(2) Method of editing continuous stitching data
* Input is completed by the steps above. For the continuous stitching, however, input all data
within the range of the presser size. Error message will be shown when the data exceeds the
range. Be sure to precisely input the presser size.
/ Refer to 4. Inputting presser type
− 39 −
18. Performing cycle stitching
This sewing machine can perform sewing of plural sewing pattern data in one cycle in the order of the data.
Use this stitching when sewing plural different button holes on the sewing product since as many as 15
different kinds of patterns can be inputted.
In addition, registration of as many as 20 cycles can be performed. Copy and use the data to fill the needs.
/ Refer to 14. Copying sewing pattern
4) Perform sewing.
Press READY key w in the state that the cycle
data is selected, and the back-light of LCD display
q shows green and it is possible to sew.
Cycle data No. 1 only has been registered at the
time of your purchase. However, sewing status
cannot be obtained since the sewing pattern has
not been inputted. Perform inputting of sewing
pattern referring to 2) Method of editing cycle data
on the next page.
− 40 −
(2) Method of editing cycle data
w e
1) Set the mode to input mode.
When the back-light of LCD display q shows the
input mode in blue color, it is possible to input the
cycle data. When the back-light is the sewing mode
in green color, press READY key w to change
over to the input mode. q
− 41 −
19. Explanation of plural motions of knife
This sewing machine can automatically actuate the knife plural times and sew a buttonhole larger than the
size of knife by setting the size of knife attached from the operation panel. Set and use this function when
sewing various sewing shapes without replacing the knife.
4) Perform sewing.
Press READY key w , and the back-light of !0 !1
LCD display q becomes green. Then it is possible
to sew. At this time, when S02 Cloth cutting length
is set to a size larger than U18 Cloth cutting knife
size which has been set above, the plural motions
of knife is automatically performed for sewing.
* If a buttonhole smaller than the size of knife
attached is desired to be sewn, error 489 will be Sewing data
displayed. S02 Cloth cut length
1st time
2nd time
3rd time
− 42 −
20. Method of changing memory switch data
1) Set the mode to input mode.
When the back-light of LCD display q shows the
input mode in blue color, it is possible to change
the memory switch data. When the back-light shows
level 1
the sewing mode in green color, press READY key
w to change over to the input mode.
4) Change data.
There are one data item to change the numerical
q
value and the other data item to select the
pictograph in the memory switch data.
No. such as is attached to the data item to
change the numerical value. Set value can be
changed by increasing/decreasing the value with
DATA CHANGE key !1 .
No. such as is attached to the data item to
select the pictograph. Pictograph can be selected !0 !1
with DATA CHANGE key !1 .
/ For the details of memory switch data, refer to
21. Memory switch data list.
− 43 −
21. Memory switch data list
(1) Level 1
☆ Memory switch data (level 1) are the motion data that the sewing machine has in common and the data
that operate on all sewing patterns in common.
No. Item Setting range Edit unit Initial value
U01 Presser lifter maximum position 0 to 17.0 0.1mm 14.0mm
Height of maximum position of pedal operation is set.
U10 Soft-start speed setting 2nd stitch 400 to 4200 100rpm 800rpm
U11 Soft-start speed setting 3rd stitch 400 to 4200 100rpm 2000rpm
U12 Soft-start speed setting 4th stitch 400 to 4200 100rpm 3000rpm
U13 Soft-start speed setting 5th stitch 400 to 4200 100rpm 4000rpm
U17 Sewing start position (Feed direction) 2.5 to 110.0 0.1mm 2.5mm
Sewing start position in terms of presser is set.
Set this item when starting position is desired to be
shifted due to overlapped section or the like.
− 44 −
No. Item Setting range Edit unit Initial value
U18 Cloth cutting knife size 3.0 to 32.0 0.1mm 32.0mm
Input knife size used.
Non-display Display
− 45 −
(2) Level 2
☆ Press MODE switch for as long as three seconds and it is possible to edit.
NO. Item Setting range Edit unit Initial value
K01 Pedal selection – – 2-pedal
Pedal type is set. / 3. How to use the pedal
K07 Max. speed limitation speed setting 400 to 4200 100rpm 3600 rpm
Max. speed of sewing machine can be limited.
When K06 Selection of machine type is set to dry
head type, max. speed is automatically limited to 3,300
rpm.
K08 Compensation of unsteady needle thread tension -30 to 30 1 0
Output value of needle thread tension is wholly offset
and compensated.
− 46 −
No. Item Setting range Edit unit Initial value
K13 Knife solenoid lifting time setting 5 to 100 5ms 15
Ineffective Effective
Permitted Prohibited
− 47 −
6. MAINTENANCE
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
0.05 mm
q
e w
− 48 −
2. Adjusting the needle thread trimmer
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
r
e
− 49 −
3. Adjusting the presser bar pressure
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
w
e
− 50 −
5. Thread tension
− 51 −
6. Cleaning the filter
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the
following work after turning the power off and ascertaining that the motor is at rest.
Hole under q
table for fan
WARNING :
1. To avoid electrical shock hazards, turn OFF the power and open the control box cover after about
five minutes have passed.
2. Open the control box cover after turning OFF the power without fail. Then, replace with a new fuse
with the specified capacity.
− 52 −
7. GAUGE COMPONENTS
2. Throat plate
A
Stitch width
5mm (Marking • AxB) 6mm (Marking • AxB)
Type
Standard (S) 40004350 (S5 • 1.4x6.2) 40004351 (S6 • 1.4x7.4)
For knits (K) 40004352 (K5 • 1.2x6.2) 40004353 (K6 • 1.2x7.4)
3. Presser
Stitch width 5 mm
Size (AxB)
1 (4x25) 2 (5x35) 3 (5x41)
Type
Standard (S) B1552781000A B1552782000 B1552783000
For knits (K) D1508771K00A D1508772K00 D1508773K00
Stitch width 6 mm
Sewing area (AxB)
B
Size (AxB)
3 (6x41)
Type
Standard (S) 14524409 A
− 53 −
8. ERROR CODE LIST
Error code Description How to recover Place of recovery
E001 Contact of initialization of EEP-ROM of MAIN CONTROL p.c.b. Turn OFF the power.
When data is not written in EEP-ROM or data is broken, initialization of
the data is automatically informed.
E007 Main shaft motor-lock Turn OFF the power
When large needle resistance sewing product is sewn
E023 Detection of step-out of presser lifting motor Possible to re-start after Standard screen
When step-out of motor is detected at the time when presser lifting motor pressing reset key.
passes origin sensor or starts operation.
E024 Pattern data size over Possible to re-start after Standard screen
When sewing cannot be performed since total size of continuous stitching pressing reset key.
data or size of downloaded data is too large.
E025 Detection of step-out of needle thread trimmer motor Possible to re-start after Standard screen
When step-out of motor is detected at the time when needle thread trimmer pressing reset key.
motor passes origin sensor or starts operation.
E026 Detection of step-out of bobbin thread trimmer motor Possible to re-start after Standard screen
When step-out of motor is detected at the time when bobbin thread trimmer pressing reset key.
motor passes origin sensor or starts operation.
E030 Needle bar upper position failure Possible to re-start after Standard screen
When needle does not stop at UP position even with needle UP operation pressing reset key.
at the time of starting sewing machine.
E050 Stop switch Possible to re-start after Step screen
When stop switch is pressed during machine running. pressing reset key.
E052 Thread breakage detection error Possible to re-start after Step screen.
When thread breakage has occurred during machine running. pressing reset key.
E099 Interference of knife lowering command with thread trimming Possible to re-start after Standard screen
motion pressing reset key.
When inserting position of knife command is improper and knife command
interferes with thread trimming motion in case of motion by data from
external input device.
E302 Confirmation of tilt of machine head Possible to re-start after Standard screen
When tilt of machine head sensor is OFF. pressing reset key.
E303 Z phase sensor error of main shaft motor Turn OFF the power.
Z phase sensor of sewing machine motorencoder is abnormal.
E304 Cloth cutting knife sensor error Turn OFF the power.
When sensor is not OFF while knife is lowered.
E486 Eyelet knife length error Possible to re-enter after Sewing data edit screen
Eyelet knife length is too short to form the shape in case of eyelet shape. pressing reset key. [S17] Eyelet knife length
E487 Eyelet shape length error Possible to re-enter after Sewing data edit screen
Eyelet shape length is too short to form the shape in case of eyelet shape. pressing reset key. [S14] Eyelet shape
length
E488 Taper bar-tacking compensation error Possible to re-enter after Sewing data edit screen
When bar-tacking length is too short to form the shape in case of taper pressing reset key. [S08] 2nd bar-tacking
bar-tacking shape. length
E489 Knife size error (at the time of plural motions of knife) Possible to re-enter after Sewing data edit screen
When knife size is larger than cloth cutting knife size. pressing reset key. [S02] Cloth cut length
− 54 −
Error code Description How to recover Place of recovery
E492 Presser size over of basting Possible to re-enter after Sewing data edit screen
When stitching data of basting exceeds presser size. pressing reset key. [S40] Basting needle
entry compensation
E493 Presser size over of tie stitching at sewing end Possible to re-enter after Sewing data edit screen
When stitching data of tie stitching at sewing end exceeds presser size. pressing reset key. [S67] Tie stitching at
sewing end width
E494 Presser size over of tie stitching at sewing start Possible to re-enter after Sewing data edit screen
When stitching data of tie stitching at sewing start exceeds presser size. pressing reset key. [S64] Tie stitching at
sewing start width
E495 Presser size error (Width direction : right only) Possible to re-enter after Sewing data edit screen
When stitching data exceeds the size of right only of width direction of presser. pressing reset key. [S03] Knife groove width,
right or [S06] Ratio of right
and left shapes
E496 Presser size error (Width direction : left only) Possible to re-enter after Sewing data edit screen
When stitching data exceeds the size of left only of width direction of presser. pressing reset key. [S04] Knife groove width,
left or [S06] Ratio of right
and left shapes
E497 Presser size error (Length direction : front) Possible to re-enter after Standard screen
When stitching data exceeds the size of front of length direction of presser. pressing reset key.
E498 Presser size error (Width direction : right and left) Possible to re-enter after Sewing data edit screen
When stitching data exceeds the size of both right and left of width direction of pressing reset key. [S05] Overedging width,
presser. left
E499 Presser size error (Length direction : rear) Possible to re-enter after Sewing data edit screen
When stitching data exceeds the size of rear of length direction of presser. pressing reset key. [S02] Cloth cut length
E703 Panel is connected to the machine other than supposed. (Machine Turn OFF the power.
type error)
When machine type code of system is improper in case of initial communication.
E704 Nonagreement of system version Turn OFF the power.
When version of system software is improper in case of initial communication.
E730 Main shaft motor encoder defectiveness or phase-out Turn OFF the power.
When encoder of sewing machine motor is abnormal.
E731 Main motor hole sensor defectiveness or position sensor Turn OFF the power.
defectiveness
When hole sensor or position sensor of sewing machine motor is defective.
E733 Reverse rotation of main shaft motor Turn OFF the power
When sewing machine motor rotates in reverse direction.
E901 Abnormality of main shaft motor IPM Turn OFF the power.
When IPM of servo control p.c.b. is abnormal.
− 55 −
Error code Description How to recover Place of recovery
E904 Abnormality of solenoid power Turn OFF the power.
When solenoid power of servo control p.c.b. fluctuates ±15% or more.
E905 Abnormality of temperature of heat sink for servo control p.c.b. Turn OFF the power
When temperature of heat sink of servo control p.c.b. is 85˚C or more.
E907 Stitch width motor origin retrieval error Turn OFF the power.
When origin sensor signal is not inputted at the time of origin retrieval motion.
E908 Y feed motor origin retrieval error Turn OFF the power
When origin sensor signal is not inputted at the time of origin retrieval motion.
E909 Needle thread trimmer motor origin retrieval error Turn OFF the power.
When origin sensor signal is not inputted at the time of origin retrieval motion.
E910 Presser motor origin retrieval error Turn OFF the power
When origin sensor signal is not inputted at the time of origin retrieval motion.
E911 Bobbin thread trimmer motor origin retrieval error Turn OFF the power.
When origin sensor signal is not inputted at the time of origin retrieval motion.
E915 Abnormality of communication between operation panel and Turn OFF the power
main CPU
When abnormality occurs in communication.
E916 Abnormality of communication between main CPU and main Turn OFF the power.
shaft CPU
When abnormality occurs in communication.
E918 Abnormality of temperature of heat sink for main control p.c.b. Turn OFF the power
When temperature of heat sink of main control p.c.b. is 85flC or more.
E943 Defectiveness of EEP-ROM of main control p.c.b Turn OFF the power.
When data writing to EEP-ROM is not performed.
E946 Defectiveness of writing to EEP-ROM of head relay p.c.b. Turn OFF the power
When data writing to EEP-ROM is not performed.
E999 When cloth cutting knife does not return Turn OFF the power
• When cloth cutting knife does not return after the lapse of predetermined
time.
• When sensor is not turned ON while cloth cutting knife is raising (at the
time of waiting).
− 56 −
9. TROUBLES AND CORRECTIVE MEASURES
Troubles Causes Corrective measures Page
1. Needle thread breakage 1. Thread tension at parallel section is too high. ○ Decrease the thread tension at parallel P.22
section.
2. Pressure or stroke of thread take-up spring is ○ Decrease the tension of thread take-up P.51
too large. spring or decrease its stroke.
3. There is a burr or scratch on the blade point of ○ Buff the blade point of hook. Or, replace –
hook. the hook.
4. Hook timing is not proper. ○ Adjust again the hook timing with timing P.48
gauge.
5. There is a scratch on the thread path. ○ Polish the thread path with sand paper and –
buff it.
6. Attaching needle is wrong. ○ Adjust again the direction, height, etc. P.12
7. Needle is too thin. ○ Replace the needle with a thicker one. –
8. Needle tip is damaged. ○ Replace the needle. –
2. Needle thread slips off. 1. Needle thread trimmer opens too early. ○ Delay the opening timing of the needle P.49
thread trimmer.
2. Whip stitching is not formed at the start of ○ Decrease tension at the start of sewing. P.32
sewing.(Tension at the start of sewing is too
high.)
3. Threading needle thread is wrong. ○ Thread properly again. P.13
4. Speed at the start of sewing is too fast. ○ Set the soft-start function. P.44
3. Wobbling at parallel 1. Thread tension at parallel section is too low. ○ Increase the thread tension at parallel P.22
section section.
2. Bobbin thread tension is too high. ○ Decresase bobbin thread tension. P.14
(Purl stitching : 0.05 to 0.1N )
3. Pre-tension is too low. ○ Increase pre-tension. –
4. Wobbling at the start of 1. Thread tension at parallel section is too low. ○ Increase the thread tension at parallel P.22
sewing section.
2. Position of needle thread trimmer is too high. ○ Lower the needle thread trimmer to such P.49
an extent that it does not come in contact
with the presser.
3. Stroke of thread take-up spring is too large. ○ Decrease the stroke of thread take-up P.51
spring.
5. Needle thread appears 1. Bar-tacking thread tension is too low. ○ Increase the bar-tacking thread tension. P.22
on the wrong side of 2. Bobbin thread tension is too high. ○ Decresase the bobbin thread tension. P.14
material at bar-tacking (0.05 to 0.1N )
section in dumpling 3. Number of stitches of radial shape is too many. ○ Decrease the number of stitches. P.30
condition. 4. Tension at the end of sewing is too low. ○ Increase tension at the end of sewing. P.44
6. Stitches float. 1. Bobbin thread tension is too low. ○ Increase the bobbin thread tension. P.14
2. Bobbin thread comes off bobbin case. ○ Perform proper threading the bobbin case. P.13
○ Take care that the winding amount of P.24
bobbin thread is not excessive.
7. Stitch skipping 1. Button hole is small in terms of the size of ○ Replace the presser with a smaller one. –
presser.
2. Material flops because of light-weight. ○ Delay the hook-to-needle timing. P.48
(Lower the needle bar by 0.5 mm.)
3. Attaching needle is wrong. ○ Adjust again the direction, height, etc. P.12
4. Needle is bent. ○ Replace the needle. –
5. There is a burr or scratch on the blade point of ○ Buff the blade top of hook. Or, replace the –
hook. hook.
8. Thread frays. 1. Number of stitches of tie stitching is too small. ○ Increase the number of stitches of tie P.33
stitching at the end of sewing.
2. Width of tie stitching is too wide. ○ Narrow the width of tie stitching at the end P.33
of sewing.
9. L e n g t h o f n e e d l e 1. Width of tie stitching is too narrow. ○ Widen the width of tie stitching at the end P.33
thread remaining at the of sewing.
end of sewing is too 2. Tension of tie stitching is too low. ○ Increase tension at the end of sewing. P.44
long.
10. Needle thread breaks 1. Tension at the start of sewing is too low. ○ Increase tension at the start of sewing. P.32
at the start of sewing,
or the wrong side of
seam is dirty.
− 57 −
Troubles Causes Corrective measures Page
11. K n i f e d r o p s e v e n 1. Check whether the thread breakage detector ○ Adjust the detector plate. –
when needle thread is plate is properly adjusted. (Refer to the Engineer's Manual.)
cut.
12. Needle breaks. 1. Check whether needle is bent. ○ Replace the needle. P.13
2. Check whether needle comes in contact with ○ Adjust the needle-to-hook timing. P.48
the blade point of hook.
3. Check whether needle thread trimmer comes ○ Adjust the installing position of needle P.49
in contact with needle when it opens. thread trimmer.
4. Check whether needle comes in the center of ○ Re-adjust the installing position of throat –
the needle hole of throat plate. plate base.
5. Needle stop position is too low and needle
comes in contact with needle thread trimmer
when it closes.
13. Knife drops plural 1. Check whether the cloth cutting knife dropping ○ Release the plural time setting. P.42
times. is set to plural dropping.
− 58 −
1200
6
R4 R4
1130
900 78
601 290±0.5
540
180 810
140
467.5 70
R G 0
30 R4
R3
M
D Z Z
K
8-R10
151±0.5
A
70
N
20
80
25
75.5±0.5
E 90
Z Z 38
0. DRAWING OF THE TABLE
I
H J
47
360
570
419
520
407
500
50
71
− 59 −
400
390
383.5
340
276
215
F
L
B
110
R3
51
0
R4
35
25
15
115 180
0
20 C
R3
40
21 50
222.5
457.5 70 100 Z-Z (1 : 1)
649
ø26
3
8
A 2 drilled hole, depth 10 on the bottom surface E 16 drilled hole, depth 30 K 9 drilled hole, depth 20, facing depth 17
Installing position of stopper for drawer F 4-8 drilled hole L 2-2 drilled hole, depth 10 on the bottom surface
B JUKI logotype G 50 drilled hole Main switch installing position ø8.5
C 2 drilled hole, depth 10 on the bottom surface H 2-2 drilled hole, depth 10 on the bottom surface M 17 drilled hole
Installing position of drawer Pedal switch installing position N Right side
D 4-2 drilled hole depth 10 on the bottom surface I 2-3.5 drilled hole, depth 14
Stand installing hole J 30 drilled hole
-. INITIAL VALUE DATA FOR EACH SHAPE TABLE
S02 Cloth cutting length mm 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 13.0 19.1 19.1 19.1
S03 Knife groove width, right mm 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 – – 0.10 0.10
S04 Knife groove width, left mm 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 – 0.10 – 0.10
S05 Overedging width, left mm 1.70 1.70 1.70 1.70 1.70 1.70 1.4 1.4 1.4 1.4 1.70 1.70 1.70 1.70 1.70 1.4 1.4 1.70 1.70 1.70 1.70 1.70 1.70 1.70 1.70 1.70 – – – –
S06 Left/right shape ratio (right side in terms of left side) % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 – – – –
S07 Pitch at parallel section mm 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 – – – –
S08 2nd bar-tacking length mm 1.0 – 1.0 – 1.5 3.0 1.0 – 1.5 3.0 – 1.0 1.0 1.5 3.0 – – – – – 1.5 3.0 – – – – – – – –
S09 1st bar-tacking length mm 1.0 – – – – – – – – – – – – – – – – 1.0 1.0 1.0 1.0 1.0 – – – – – – – –
S10 Bar-tacking width, right compensation mm 0.0 – 0.0 – 0.0 – 0.0 – 0.0 – – 0.0 0.0 0.0 – – – 0.0 0.0 0.0 0.0 0.0 – – – – – – – –
S11 Bar-tacking width, left compensation mm 0.0 – 0.0 – 0.0 – 0.0 – 0.0 – – 0.0 0.0 0.0 – – – 0.0 0.0 0.0 0.0 0.0 – – – – – – – –
S12 Taper bar-tacking offset, left mm – – – – – 0.85 – – – 0.85 – – – – 0.85 – – – – – – 0.85 – – – – – – – –
S13 Taper bar-tacking offset, right mm – – – – – 0.85 – – – 0.85 – – – – 0.85 – – – – – – 0.85 – – – – – – – –
S14 Eyelet shape length mm – – – – – – 2.0 2.0 2.0 2.0 – – – – – 2.0 2.0 – – – – – – – – – – – – –
S15 Number of stitches of eyelet shape Stitch – – – – – – 3 3 3 3 – – – – – 3 3 – – – – – – – – – – – – –
S16 Eyelet width mm – – – – – – 1.0 1.0 1.0 1.0 – – – – – 1.0 1.0 – – – – – – – – – – – – –
S17 Eyelet length mm – – – – – – 3.0 3.0 3.0 3.0 – – – – – 3.0 3.0 – – – – – – – – – – – – –
S18 Round type shape length mm – 2.0 2.0 2.0 2.0 2.0 – 2.0 – – 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 – – 2.0 2.0 2.0 2.0 – – – –
S19 Number of stitches of radial shape Stitch – – 3 3 3 3 – 3 – – – – – – – – – 3 – – – – 3 3 3 – – – – –
S20 Radial shape reinforcement (with/without) – – Without Without Without Without – Without – – – – – – – – – Without – – – – Without Without Without – – – – –
S21 Pitch at bar-tacking section mm 0.30 0.30 0.30 Å[ 0.30 0.30 0.30 – 0.30 0.30 0.25 0.30 0.25 0.25 0.25 0.25 0.30 0.30 0.25 0.30 0.30 0.30 0.25 0.30 0.25 0.25 – – – –
S22 1st clearance mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5. 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 – 2.0 2.0 2.0
S23 2nd clearance mm 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 – 2.0 2.0 2.0
S31 1/2 stitching Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single Single – – – Single
S32 Double stitching cross selection < < < < < < < < < < < < < < < < < < < < < < < < < < – – – <
S33 Double stitching width compensation mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 – – – –
S34 Number of times of basting Time 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 2 2 –
S35 Pitch of basting mm 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 –
S36 Rolling length of basting mm 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 –
S37 Rolling pitch of basting mm 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 –
S38 Rolling width of basting mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 –
S39 Compensation before/after needle entry of basting mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 –
S40 Compensation left/right needle entry of basting mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 –
S41 Compensation of left side position of basting mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 –
S42 Compensation of right side position of basting mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 –
S44 Speed setting of basting rpm 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 –
S45 Sewing together function (without/with) Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without – – – –
S46 Width of sewing together mm 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 – – – –
S47 Pitch of sewing together mm 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 – – – –
S51 Left parallel section tension 120 60 120 120 120 120 60 60 60 60 60 60 60 60 60 60 60 120 60 60 60 60 60 60 60 60 60 60 60 60
S52 Right parallel section tension 120 60 120 120 120 120 60 60 60 60 60 60 60 60 60 60 60 120 60 60 60 60 60 60 60 60 60 60 60 60
S53 Left parallel section tension (1st cycle of double stitching) 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 – – – –
S54 Right parallel section tension (1st cycle of double stitching) 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 – – – –
S55 1st bar-tacking section tension 35 60 120 35 35 35 60 60 60 60 60 60 60 60 60 60 60 30 60 60 60 60 60 60 60 60 – – – –
S56 2nd bar-tacking section tension 35 60 35 35 35 35 60 60 60 60 60 60 60 60 60 60 60 120 60 60 60 60 60 60 60 60 – – – –
S57 Setting of needle thread tension at sewing start 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25
S58 Setting of needle thread tension of basting 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ---
S59 ACT timing adjustment at 1st bar-tacking start Stitch 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 – – – –
S60 ACT timing adjustment at the start of right overedging Stitch 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
S61 ACT timing adjustment at 2nd bar-tacking start Stitch 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 – – – –
S62 Number of stitches of tie stitching at the start of sewing Stitch 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
S63 Sewing pitch of tie stitching at the start of sewing 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
S64 Tie stitching width at sewing start mm 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
S65 Lengthwise compensation of tie stitching at the start of sewing mm 0.0 1.5 0.0 1.5 0.0 0.0 0.0 1.5 0.0 0.0 1.5 0.0 0.0 0.0 0.0 1.5 1.5 1.5 1.5 1.5 0.0 0.0 1.5 1.5 1.5 1.5 0.0 0.0 0.0 0.0
S66 Crosswise compensation of tie stitching at the start of sewing mm 0.0 0.0 0.0 0.0 0.0 0.7 0.0 0.0 0.0 0.7 0.0 0.0 0.0 0.0 0.7 0.0 0.0 0.0 0.0 0.0 0.0 0.7 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
S67 Tie stitching width at sewing end mm 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
S68 Number of stitches of tie stitching at sewing end Stitch 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
S69 Lengthwise compensation of tie stitching at the end of sewing mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
S70 Crosswise compensation of tie stitching at the end of sewing mm 0.9 0.9 0.9 0.9 0.0 0.7 0.9 0.9 0.0 0.7 0.9 0.9 0.9 0.0 0.7 0.9 0.9 0.9 0.9 0.9 0.0 0.7 0.9 0.9 0.9 0.9 0.0 0.0 0.0 0.0
S81 Knife motion (With/without) With With With With With With With With With With With With With With With With With With With With With With With With With With – With With With
S83 Knife at 1st cycle of double stitching (Without/with) Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without Without – – – –
S84 Max. speed limitation rpm 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600 3600
S86 Pitch of going mm – – – – – – – – – – – – – – – – – – – – – – – – – – 0.80 0.80 0.80 0.80
S87 Width of going mm – – – – – – – – – – – – – – – – – – – – – – – – – – 1.7 1.7 1.7 1.7
S88 Pitch of returning mm – – – – – – – – – – – – – – – – – – – – – – – – – – 0.80 0.80 0.80 0.80
S89 Width of returning mm – – – – – – – – – – – – – – – – – – – – – – – – – – 1.7 1.7 1.7 1.7
- 60 -