Professional Documents
Culture Documents
X-BT Stainless Steel Threaded Studs: Dimensions Product Data General Information
X-BT Stainless Steel Threaded Studs: Dimensions Product Data General Information
X-BT Stainless Steel Threaded Studs: Dimensions Product Data General Information
[0.177"]
1 2 3 CR 500 (CrNiMo alloy) fu ≥ 1850 N/mm2
[0.177"]
o 4.5
M10/
o 4.5
W10
M8
S31803 fu ≥ 1400 N/mm2
[0.472"]
fu ≥ 1400 N/mm2
[0.472"]
o 12
o 12
N 08926 (HCR)
➁ Threaded sleeve: S 31600
24 [0.945"] 4 14 4
31.3 [1.232"] [0.551"] ➂ SN12-R washers: S 31635
21.3 ➃ Sealing washers: Elastomer, black
[0.839"]
Resistant to UV, salt
X-BT W10-24-6-R X-BT M8-15-6-R water, water, ozone,
X-BT M10-24-6-R
1 2 1 2
oils, etc.
[0.177"]
[0.177"]
M10/
W10
o 4.5
o 4.5
M8
16
Fastening tool
26 [1.024"] [0.630"]
31.3 [1.232"]
DX 351-BT / BTG
21.3
[0.839"]
See fastener selection for more details.
o 4.5
5 1 3
[0.472"]
o 12
20 4
[0.787"]
31.3
[1,232"]
Applications
Examples
≥ 8 mm
7 / 2010 2.119
X-BT
Load data
Recommended loads
N
Steel grade: S235, S355, Grade 50
Europe, USA A36 and stronger steel
V
M
Tension, Nrec [kN/lb] 1.8 / 405 2.3 / 517
Shear, Vrec [kN/lb] 2.6 / 584 3.4 / 764
Moment, Mrec [Nm/lb] 8.2 / 6 8.2 / 6 Example:
Torque, Trec [Nm/lb] 8 / 5.9 8 / 5.9
Z3
Conditions for recommended loads: Z2
FN
• Global factor of safety for static pull-out > 3 (based on 5% fractile value)
F
• Minimum edge distance = 6 mm [ /4”].1
Z V
• Effect of base metal vibration and stress considered.
• Redundancy (multiple fastening) must be provided. 1
• The recommended loads in the table refer to the resistance of the individual fasten-
ing and may not be the same as the loads FN and FV acting on the fastened part.
Note: If relevant, prying forces need to be considered in design, see example. Moment acting on fastener
shank only in case of a gap between base and fastened material.
Cyclic loading:
• Anchorage of X-BT-R threaded stud in steel base material is not affected by cyclic loading.
• Fatigue strength is governed by fracture of the shank. Inquire at Hilti for test data if high cycle loading has to be
considered in the design.
2.120 7 / 2010
X-BT
Application requirements
Thickness of base material
> 8mm [5/16"]
Lg
tWASHER
tI
Note:
For X-BT with SN 12R sealing washer tl ≥ 2.0 mm
For X-BT M6 / W6 with SN 12R sealing washer tl ≥ 1.0 mm
7 / 2010 2.121
X-BT
Corrosion information
The corrosion resistance of Hilti CR500 and S31803 stainless steel material is equivalent to
AISI 316 (A4) steel grade.
Studs made of N 08926 (HCR) material with higher corrosion resistance, e.g. for use in road
tunnels or swimming pools, are available on special order.
Application limit
> 8mm [5/16"] • tII ≥ 8 mm [5/16”] → No through penetration
• No limits with regards to steel strength
Fastener selection
Fasteners Tool
Designation Item no. Designation
X-BT M8-15-6 SN12-R 377074 DX 351-BTG
X-BT M10-24-6 SN12-R 377078 DX 351-BT
X-BT W10-24-6 SN12-R 377076 DX 351-BT
X-BT M8 without washer 377073 DX 351-BTG
X-BT M10 without washer 377077 DX 351-BT
X-BT W10 without washer 377075 DX 351-BT
X-BT M6-24-6 SN12-R 432266 DX 351-BT
X-BT W6-24-6 SN12-R 432267 DX 351-BT
2.122 7 / 2010
X-BT
Installation
X-BT with washer X-BT without washer
Fastened material hole ∅ Fastened material hole ∅
≥ 13 mm ≥ 11 mm for X-BT M/W10
≥ 9 mm for X-BT M8
X-BT M6 / X-BT W6
Fastened material with Fastened material with
pre-drilled hole diameter pre-drilled hole diameter
< 7 mm ≥ 7 mm
7 / 2010 2.123
X-BT
1. 2. 3. 4. 5.
Mark location for Pre-drill with Drive X-BT-R Hang unit on studs. Tighten using a
each fastening TX-BT 4/7 step studs into drilled Put on washers and screwdriver with
shank drill bit hole hand tighten nuts torque clutch
51
Pre-drill until the Adjust power on Sealing washer must Tightening torque:
shoulder grinds a DX 351 BT so that be properly com- Trec ≤ 8 Nm
shiny ring (to ensure the fastener standoff pressed! (5.9 ft-lb)!
proper drilling depth) hNVS, is not greater
than:
hNVS ≤ 26.8 mm
(X-BT M/W10 ...-R,
Trec
X-BT M/W6...-R)
hNVS ≤ 16.8 mm
(X-BT M8…-R)
3 2 1
2.124 7 / 2010