Professional Documents
Culture Documents
1701gibs Cam
1701gibs Cam
Turning
Gibbs and Associates
5400 Tech Circle
Moorpark, CA 93021
(805) 523-0004
May 1, 1996
◆ L e v e l 0 T u r n i n g GFK-1701
PROPRIETARY NOTICE
This document contains propriety information of Gibbs and Associates and is to be used only
pursuant to and in conjunction with the license granted to you with respect to the accompanying Gibbs
and Associates licensed software. Except as expressly permitted in the license, no part of this document
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, magnetic, optical, chemical, manual or
otherwise, without the prior written permission from a duly authorized representative of Gibbs and
Associates.
It is strongly advised that you carefully review the license in order that you understand your rights
and obligations related to the licensed software and the accompanying user documentation.
Use of the computer software and the user documentation has been provided pursuant to a Gibbs
and Associates license agreement.
Acknowledgements:
Written by Shannon McConville.
Thanks to Sean Canteberry, Gary Esser, Kristin Esser, Bill Gibbs, Charles Haden, Tom Hubina, Michael
Kelley, Israel Klain, Pete Jackson and Jeff Myers for their input and assistance.
This application was ported to the DOS operating system using Bawamba Software Inc.'s Multiplatform
Compatibility Package.
Trademarks:
MS-DOS is a trademark of Microsoft Corporation
Macintosh is a trademark of Apple Computer, Inc.
Table of Contents
CHAPTER 1: INTRODUCTION 4
How to Learn the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Balloons and Prompting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating Systems Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C H A P T E R 2 : I N T E R FA C E 6
Cursors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clipboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
C H A P T E R 3 : PA RT S E T- U P 17
Document Control Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C H A P T E R 4 : G E O M E T RY C R E AT I O N 20
Geometry Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Geometry Expert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Edit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Modify Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Workgroup Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Printing the Part Geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Geometry Exercise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
C H A P T E R 5 : T O O L C R E AT I O N 49
Tool Creation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Tool Creation Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Tool List Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
CHAPTER 6: MACHINING 56
Machining Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Creating an Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
What is a Cut Shape?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Multiple Process Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Modifying an Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
1
◆ L e v e l 0 T u r n i n g GFK-1701
Machining Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Process Dialogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Clearance Moves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Machining Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Operation Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Operation Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Printing the Toolpath. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
CHAPTER 10 : COMMUNICATIONS 92
Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Communicating with a CNC Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
CHAPTER 11 : TUTORIAL 95
Creating a New Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Creating Part Geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Creating a Tool List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Creating Operations With the Process List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Part Blueprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
2
GFK-1701 T a b l e o f C o n t e n t s ◆
INDEX 178
3
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 1 : I n t r o d u c t i o n
HOW TO LEARN THE SYSTEM
Congratulations on receiving the most productive programming system available! The best
way to learn how to use this software is to do the exercise in the Geometry Creation Chapter and then
go through the Tutorial Chapter. For simple explanations of items on screen and their purpose, use
Balloons and Prompting provided in the Help menu or the reference information provided in the
manual.
O P E R AT I N G S Y S T E M S G L O S S A RY
The MS-DOS®, Windows NT®, Windows 95® and MacOS® operating systems use different
terminology for certain common items. A short list has been provided to help eliminate possible
confusion. Refer to the Operating Systems Appendix for additional information on the differences
between the DOS, Windows NT, Windows 95 and Macintosh operating systems.
EQUIVALENT TERMS
file = document
program = application
directory = folder
backspace key (not delete or del) = delete key (not del)
Operating system symbol : This symbol appears throughout the manual to indicate when
OS there are variations in specific system functions depending on the operating system.
4
GFK-1701 I n t r o d u c t i o n ◆
S Y S T E M O V E RV I E W
This system is designed to be extremely flexible to allow the user the freedom to create parts in
any way that comes naturally. The "modeless" interface allows the user to have geometry creation,
tool creation, machining capabilities and post processing functions available at all times. However,
there are certain basic elements required to create a part. There must be geometry, a tool, and a
toolpath (an operation) created before post processing. The Top Level palette, shown below, is
organized in a logical manner for building a part. A part does not have to be created in this order, it
only serves as a guideline. Refer to the the Tutorial Chapter for complete step-by-step instructions
on part creation.
Create a tool.
Create a toolpath.
Render.
Post Process.
5
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 2 : I n t e r f a c e
This system uses a Graphic User Interface (GUI). This simply means that pictures or symbols
are used in place of text whenever possible. This section of the manual describes the different
interface objects and their uses.
CURSORS
The cursor is the object moved with the mouse. Its appearance changes depending on its
location. The appearance of the cursor dictates its usage.
Black pointer: This cursor is used to select objects and geometry by clicking on them. It also
provides a method of zooming in on an area by dragging a box around it.
White pointer: This cursor functions the same as the black pointer, except it is in multiple
selection mode, meaning that multiple items, such as geometry or tiles, can be selected as a
group. The white pointer appears when the Shift key is held down or when a geometry sub-
palette is open.
Mover Tool: This cursor is used to drag moveable palettes and dialogs. The cursor changes to
the mover tool when it is placed on the edge of a palette or in a dialog’s title bar. Move the
palette or dialog by holding the mouse button down and dragging it to a different location.
Pointing Finger: This cursor indicates that the cursor is over a button. Push the button by
clicking on it with the mouse button.
Hand: This indicates that the cursor is over a draggable object such as a tile. This cursor is
also used to roll the trackball.
I Beam: This indicates that the cursor is in a location where typed input is accepted. It is a
flashing cursor.
Area Select: The cursor changes to this while doing a Mouse drag or zooming in on an area.
6
GFK-1701 I n t e r f a c e ◆
ACTIONS
There are a number of actions used throughout the system.
• Moving the cursor: the cursor is moved and positioned with the mouse
• Click: a quick tap on any mouse button
• Double click: two quick taps on any mouse button
• Type: using the keyboard
• Drag: position cursor, hold mouse button down, reposition cursor, release mouse button
• Shift click: hold shift key down while clicking the mouse
• Shift double click, Ctrl click, Ctrl double click, etc.: hold down stated key and
click (or double click)
OBJECTS
There are several interface objects used throughout the system.
• Drawing Windows
• Palettes
• Dialogs
• Tile Lists
• Menus
• Machining Markers
• Balloons/Prompts
• Wastecan
Menu Bar Drawing
Window
Tile List
Balloon
7
◆ L e v e l 0 T u r n i n g GFK-1701
DRAWING WINDOW
The drawing window is the full size of the screen. All drawing of geometry, toolpaths, and
rendered images appear in the drawing window. It is not moveable. All other interface objects
appear in front of the drawing window.
PALETTES
A palette is a collection of functions grouped together in a logical manner for the user. Some
palettes are moveable, others are not.
Top Level Palette: This palette is made up of buttons. These buttons can be either “on”
(depressed) or “off” (raised). Clicking once on a button turns it on and accesses the
appropriate dialog or palette. Another click will turn the button off and put any dialogs or
palettes away. The top level palette cannot be moved.
Cut Part Rendering palette: This palette provides control over the
rendering process. It allows the user to control the speed of the
rendering process, the operations that will be rendered, and the
way the tool will be displayed. This is also a moveable palette.
8
GFK-1701 I n t e r f a c e ◆
View Control Palette (Trackball) : The View Control Palette allows the user to
easily change the current view of the part. The buttons around the outside
provide standard view changes, redraws and unzooms. The center ball
operates like a trackball and rolls to allow the part to be viewed from any
orientation. When the cursor is placed over the ball, it changes into a hand,
which indicates that the ball can be rolled. Holding the mouse button down
and moving the mouse will roll the trackball. The black outlined box on the
ball represents the orientation of the part. The "T" identifies the top surface of the part. The
dimensions of the box do not change with the actual part size. X is the long axis. Once the desired
view is obtained, and the mouse button is released, the part is redrawn in the new view. The ball has
four small solid black rectangles around it, inside the ring of buttons (located at 12:00, 3:00, 6:00,
9:00). These are called ball "handles". Drag these handles for a single axis view change. The
trackball is a moveable palette, drag its edge to move it.
DIALOGS
Dialogs are used when information is needed from the user. This information is conveyed
through text boxes, radio buttons, yes/no buttons, and pop-up menus.
Text boxes: Items that require keyboard
input have a box next to them. If you click
once in a text box, a flashing text cursor
will appear where you clicked. Anything
Text Box typed will begin where the flashing text
cursor is. To move the text cursor, simply
click the desired location. Double clicking in a text box will select (highlight) everything in the text
box. Anything typed at this point will completely replace the current contents of the box. To select
only portions of the contents of the text box, click before or after the text to be edited, hold the mouse
button down and drag. Anything that is highlighted can be deleted by hitting the backspace key.
Moving from one text box to another can be accomplished by simply clicking in the desired
box, or hitting the Tab key. Hitting the Tab key moves the cursor from box to box, and highlights
the entire contents of each box.
The contents of all text boxes can be cut, copied and pasted to and from the Clipboard by
choosing items from the Edit Menu.
Math Input in a Text box: All number input boxes will accept the four standard math function symbols
(+ - x / ), as well as a number of special functions, (both * and x are used for multiplication). Hitting
the equal key or tab key on the keyboard will display the final value. Special math functions
include:
r = squareroot
s= sine
c= cosine
t= tangent
a= arctangent
m= convert from inch to millimeter (x 25.4)
i= convert from millimeter to inch (/ 25.4)
9
◆ L e v e l 0 T u r n i n g GFK-1701
Angle values follow the standard Cartesian coordinate system, shown below. Negative values
are acceptable as input.
Radio buttons: Radio buttons come in groups, much like a multiple choice question.
Depressing one will pop up the rest. The button that is depressed displays a small
red dot or "light" to indicate that it is "on".
Yes/No buttons: Yes/no buttons come one per option. Depress the button for
yes, pop it up for no. The button that is depressed displays a small red dot or
"light" to indicate that it is "on".
10
GFK-1701 I n t e r f a c e ◆
Close Box Dialog Name Title Bar Moveable dialogs: Some dialogs can be
moved to different locations on the
screen. The area at the top of the dialog is
called the Title Bar. The Title Bar shows
the name of the dialog. Drag the Title Bar
to move the dialog. The small box in the
upper left corner of the window is the
Close Box. Clicking in this box puts the
dialog away. Double-clicking on the title
bar will hide the dialog and leave only the
title bar. An additional double-click will
restore the dialog.
Open dialog: The Open dialog is used to locate, view, and open files.
Current Directory/Folder: Pop-up menu to access
Displays a list of all Name of the Part Preview: Displays
a higher level directory,
available files in the current disk the last rendered image
displays current directory
current directory of the selected part
11
◆ L e v e l 0 T u r n i n g GFK-1701
Tiles: The four different types of tiles used by the system are listed below.
Function tiles (Machining palette)
Tool tiles (Tool Tile list)
Process tiles (Process Tile list)
Operation tiles (Operation Tile list)
Although the functionality of each type of tile is different, they have common features. All tiles
have a similar appearance, grey and square. Tiles can be dragged to Tile lists.
Function tiles: The four types of Function tiles, from left to right , are
Contouring, Roughing, Threading, and Drilling. Function tiles are
dragged to a Process List location to create a Process tile.
Tool tiles: A Tool tile is created by double clicking on an empty Tool List location. This
brings up the Tool dialog. A Tool tile displays a small tool symbol and the tools insert width.
Process tiles: A Process tile is created by dragging one Tool tile and one Function tile to a
Process list location. A completed Process tile displays the tool number with a box around
it and a function symbol. When a Process tile is complete, a Process dialog specific to the
selected machining function will appear on the screen. An incomplete Process tile displays either the
tool number or the function symbol.
Operation tiles: Operation tiles are created automatically from Process tiles when the
Do it or Redo it button is depressed. Contouring and roughing functions require geometry
to be selected, while drilling and threading operations do not require geometry. Each tile
contains one operation. An Operation tile displays the tool number and function symbol.
12
GFK-1701 I n t e r f a c e ◆
MENUS
Menu Bar: The menu bar shown below is located at the top of the screen. It is available to the user at
all times. To access the menu bar, position the cursor over the menu bar title, hold the mouse button
down, drag the cursor until the desired item is highlighted, and release the mouse button. If a menu
item is grayed out, it cannot be selected. Selecting geometry or some other appropriate item on the
screen may change the menu item so that it is available for selection. Some menu items are grayed
out because they are not supported by the Level 0 product. Refer to the Menus Appendix for a listing
of these items.
OS The symbol next to the letter will be different depending on the operating system and the
selection made in the Interface Preference.
MACHINING MARKERS
Machining Markers allow the user to specify the Start and End feature and Start and End point
of the cut shape, the cut direction, and the offset position of the tool. These markers appear on the
screen when geometry is selected for contouring and/or roughing processes.
Start Feature: The geometry feature (line or circle) on which the tool will start cutting.
Start Point: The point on the Start Feature where the tool will start cutting.
End Feature: The geometry feature on which the tool will stop cutting.
End Point: The point on the End Feature where the tool will stop cutting.
Cutter Side and Direction: The circles represent the offset position of the tool with
regard to the cut shape. The two possible options are the inside of the cut
shape or the outside of the cut shape. The arrows indicate which direction the
tool will travel. Simply click on the desired circle and direction arrow.
13
◆ L e v e l 0 T u r n i n g GFK-1701
BALLOONS/PROMPTS (CAT)
Balloons and prompts provide on-line help for the user. They can be turned on and off at any
time using the Help menu.
Error Balloons: Error Balloons alert the user whenever an invalid value has
been entered. They are outlined red and go away automatically when a
valid value is typed in.
S H O RT C U T S
Button Shortcut: In some cases, buttons may be depressed by actions other than clicking on them.
Whenever a button has a black outline around it, it can be depressed by hitting the
enter or return key.
14
GFK-1701 I n t e r f a c e ◆
SELECTION
Three classes of objects may be selected in the system: text, geometry features and tiles.
Selection techniques are described below. Refer to the Shortcuts Appendix for more information.
TEXT SELECTION
To select text:
• Click and drag the cursor over some text.
The text will become selected.
• Double-click in a text box.
All text in the box will become selected.
• Hit the tab key to move from one text box to another.
All text in the box will become selected.
GEOMETRY SELECTION
To select a single geometry feature:
• Click on a feature.
The feature will become selected. If any other features were selected, they will
become deselected.
TILE SELECTION
To select a single tile:
• Click on a tile.
The tile will become selected. If any other tiles were selected, they will become dese-
lected.
COLORS
The system uses colors to graphically display different items drawn on the screen. The color
scheme for geometry, toolpaths and cut part rendering is listed below.
GEOMETRY
Colors Meaning
Yellow Unconnected Geometry
Light Blue Connected Geometry
TOOLPATHS
Colors Meaning
Dark Blue Cut Shape; selected area of a shape to be machined
Solid Orange Feed Move in a Toolpath
Dashed Orange Rapid Move in a Toolpath
Dashed Gray Rapid Move used for positioning/tool change
Solid Gray Approach Feed Move
RENDERING
Colors Meaning
Blue Stock
Yellow Rendering of selected operation and/or selected tools
Gray Rendering of unselected operations and/or unselected tools
Red Tool Interference
THE CLIPBOARD
The Clipboard is used as a temporary storage place for geometry and text. Using the Cut option
from the Edit menu will delete whatever items are selected and replace the contents of the Clipboard
with them. Using Copy will leave the selected items in their current location and replace the contents
of the Clipboard with a duplicate of them. Choosing Paste can do two things. If something is selected
it will replace that selection with the contents of the Clipboard. If nothing is selected, the contents of
the Clipboard will be pasted in either the drawing window or in an active text box, depending on
whether the Clipboard contains text or geometry. The Clipboard can only hold one selection at a
time. This means that it can hold either text or geometry, but not both. If text is copied into a
Clipboard holding geometry, the geometry in the Clipboard will be lost. The contents of the
clipboard will also be lost when a file is closed, the software is quit out of, or the computer is shut
down. Therefore, geometry can not be cut, copied or pasted between different part files because the
contents of the clipboard are deleted when the part file is closed.
16
GFK-1701 P a r t S e t - u p ◆
CHAPTER 3 : P a r t S e t - U p
DOCUMENT CONTROL DIALOG
Clicking on the Document Control button will bring up the Document Control dialog.
This dialog is actually a combination of two linked dialogs. The top dialog contains file
management selections and also provides measurement type options.
The bottom dialog provides specific information about the part such as stock size,
clearance moves and tool change positioning.
File
Management
Measurement
Type
X Dimension
Style
Stock Size
Diagram
Tool Change
Position
Auto Clearance
Fixed Clearance
Positions
Part Comment
The buttons used for file management, described below, are also available under the File menu.
Open Button: Clicking on the Open button will bring up the Open Dialog which allows the user to
select which file to open. If a file is currently open, it will be closed and the selected file will be
opened.
New Button: This button will create a new file by opening a dialog and asking for a file name and a
location to save the new file. If there is a file open, it will be closed.
17
◆ L e v e l 0 T u r n i n g GFK-1701
Save Button: If there have been any changes made while the file was open, this button will save the
changes.
Save As Button: This button will open a dialog asking for a file name and a location to save the
current file. The changes made since the last Save command will be written into the new file. The
original file will not be affected. The new file will become the current, open file.
Save a Copy Button: This button is very similar to the the Save As button. The system will create a
duplicate copy of the open file. The original file remains the current, open file. The name of the
duplicate file can be changed.
On DOS systems, if the original file name is less than 8 characters, the system will add
OS underscores to make the duplicate file's name 8 characters in length. If the original file's
name is 8 characters, the system will change the last character to an underscore to
distinguish the original file and the copy. On Macintosh, Windows NT and Windows 95 systems, the
word “copy”will be added at the end of the file name to distinguish it from the original.
Close Button: This button closes the current file. If the file has not been saved before clicking on the
Close Button, a dialog will come up asking if the file should be saved.
Measurement Type: These two radio buttons determine whether values input will be
based on an English or metric standard and entered in inches or millimeters. The
measurement type used by the post processor is determined by the post processor
itself. There are English and metric post processors. If an English post is used on a metric part, the
posted numbers will be converted from millimeters to inches. Likewise, metric posts will convert
values from inches to millimeters.
X Dimension Style: These two radio buttons determine whether the X values for the
part are input as radii or diameters. Some text boxes, in particular dialogs, specify
that the value entered is either a radius or a diameter value, regardless of the
selection made here.
18
GFK-1701 P a r t S e t - u p ◆
Tool Change: If the Tool Change option is turned “on”, the turret will be sent to
the X and Z dimensions specified when a tool change occurs. If Tool Change
is not on, it is assumed that either fixture offsets are being used or the operator
will hand input the tool change moves.
Comment: Any text entered as a part comment will be shown in the part preview section of the Open
dialog.
19
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 4 : G e o m e t r y C r e a t i o n
G E O M E T RY O V E RV I E W
Geometry must be created in order to machine a part. All part geometry is created
using the Geometry Expert spreadsheet. Geometry Expert combines the creation and
connection of all geometry features in one powerful and easy to use method. Once
created, geometry can be duplicated and modified using items in the Edit Menu and the
Modify Menu. There is an exercise at the end of this chapter that provides detailed
instructions on creating part geometry.
G E O M E T RY E X P E RT
Geometry Expert is a method of geometry creation which facilitates the fast creation of
simple parts and the simplified creation of more complex parts, along with being very easy to learn
and use. Geometry Expert is designed to create a single, continuous, shape. It allows the user to
define, create and connect shape features while following along the path of the part.
Geometry Expert has a tabular format, which operates much like a standard spreadsheet.
Features are defined by entering dimensions into the cells (text boxes) of the feature rows. Each
row creates a different feature. Features are defined in the same order as they are encountered
along the shape path.
Creating a shape using Geometry Expert is akin to “walking” around the path of the shape,
indicating such items as location, direction and the distance being traveled. While this is similar to
standard shape creation techniques, Geometry Expert goes one step further. It applies its inherent
knowledge of geometric principles and follows a logical course, which allows for the creation of
complete, connected, geometrically correct shapes requiring the least amount of input from the
user.
Geometry Expert, as the name implies, provides the user with a built-in consultant on the
rules and principles of geometry. The creation of simple shapes, containing primarily horizontal
and vertical lines, such as shafts, is almost effortless using Geometry Expert. The default settings
and automatic angle toggling allow the user to create alternating, intersecting horizontal and
vertical lines in the fastest manner possible. The user only needs to enter one value in order to
define the line. The creation of more complex shapes, containing multiple arcs and angled lines, is
greatly simplified due to the fact that Geometry Expert constantly applies its built in logic and
knowledge of geometry to guide the user through the process.
Finally, Geometry Expert is a very powerful editing tool. The associative capabilities of
Geometry Expert make editing any existing shape a very easy process. The system handles the
dimension changes while maintaining all the proper connections and relationships between pieces
of geometry (eg. intersections and tangencies). Feature dimensions can be adjusted by simply
changing the values in the spreadsheet. Geometry Expert handles all of the calculations and
adjustments to the other features that are affected by the changes. Geometry Expert frees the user
from needing to understand complex geometrical relationships and calculate feature dimensions.
Instead, the user can simply enter the specifications provided on the part blueprint and let
Geometry Expert do the rest.
20
GFK-1701 G e o m e t r y C r e a t i o n ◆
Feature Row
Scroll Bar
Features are defined in the order that they appear along the path of the shape. When the
Geometry Expert spreadsheet is open on the screen the user can create fully connected shapes by
entering feature specifications in each of the rows. Because Geometry Expert creates connected
shapes, each feature is dependent on and aware of the preceding and following features.
The feature row that is being worked on at any given time is referred to as the “current row”.
The current row has an upraised frame and is outlined in either yellow or black. When the current
row contains adequate information, it is outlined in yellow. The prompt at the bottom of the
spreadsheet, which gives the status of the current row, will indicate what will happen when the row
is entered.
The current row will be outlined in black if it does not contain enough information. The
prompt will indicate what additional information is needed to define the row. If the user attempts
to enter a row that does not contain enough information, an error balloon will come up, again
indicating what other information is required. When the current feature row contains the
appropriate information, the row is entered into the spreadsheet by hitting the enter or return key.
Entering a new row moves the cursor down to the next row in the spreadsheet, which will now be
the current row. The enter and return keys only move the current row down in the spreadsheet if a
new row is being created. Otherwise, the arrow keys or the cursor must be used to maneuver
through the rows in the spreadsheet.
Each feature is drawn on the screen as soon as the spreadsheet contains the necessary
information. Some features cannot be drawn until later features are defined. These are referred to
as “floating features” and are explained later in this section.
Creating part geometry with Geometry Expert is accomplished by walking along the path of a
shape, and defining features as they are encountered. In this way, all features are automatically
connected to the preceding and following features. Because of this methodology, sometimes it is
necessary to specify the correct direction of a feature, in addition to indicating its magnitude.
For arcs, the selected feature type indicates the direction, either clockwise or counter-
clockwise. For lines, the angle value indicates the direction. For example, a horizontal line can
either be defined with an angle value of 0° or 180°; both will draw the same line, but in the
opposite direction. Specifying the correct line direction is only an issue if the previous or next
feature is going to be an arc. When that is the case, it is necessary to indicate to the system what
direction the line is moving. Again, checking the line direction should only be necessary when the
line is being connected to an arc.
21
◆ L e v e l 0 T u r n i n g GFK-1701
Geometry Expert button: The Geometry Expert button is located in the last position in the
Geometry Creation palette. Clicking on this button brings up the Geometry Expert
spreadsheet, shown below, which allows the user to create connected shapes by entering
feature dimensions in the rows of the spreadsheet.
Horizontal (Z) Coordinate Vertical (Xd/Xr) Horizontal (Z) Coordinate Vertical (Xd/Xr) Coordinate
of Endpoint Coordinate of End Point of Line Point/Centerpoint of Line Point/Centerpoint
Close Box
Reference #
Feature Type
Current Row
Prompt
Angle of Line/ Length of Line Size Box
Radius of Circle or Chamfer
22
GFK-1701 G e o m e t r y C r e a t i o n ◆
Reference #: Every feature that is created is assigned a reference number by the system. The
letter indicates what type of feature it is, L for line, C for circle, and the number indicates the
creation order. These reference numbers may change during the course of creating geometry,
but will not affect the shape.
EP Z: The number entered in this cell is the horizontal or Z coordinate of the endpoint of the
current feature. When a feature is defined with an endpoint, the system will draw the feature
and trim it at the specified endpoint. Endpoint specifications are required if the next feature
needs a start point in order to be correctly defined.
EP Xd/Xr: The number entered in this cell is the Xd/Xr or vertical coordinate of the endpoint of
the current feature.
EXAMPLE: The row shown below will create a 45° line with an endpoint drawn at
Z -2, Xd 3. The next feature that is defined in the spreadsheet will start at the end
point of this feature.
Angle/Rad: The number entered in this cell is dependent on the feature type selected.
If the feature type is a line, this number specifies the angle of the line. The angle value for a
line defaults to either 90°/270° or 0°/180° allowing for the creation of vertical or horizontal
lines, respectively. The system toggles between these angle values which makes the creation
of intersecting horizontal and vertical lines a very quick and easy process. The user can
change the default values by simply entering the new numbers in the cells. If the feature
type is an arc or fillet, this number specifies the radius.
23
◆ L e v e l 0 T u r n i n g GFK-1701
EXAMPLE: The row shown below will create a fillet between the previous and fol-
lowing feature with a radius of 0.2.
Length: The number entered in this cell is the length of the current feature. The length cell
is only active if the feature type is either a line or a chamfer.
LP/CP Z: The number entered in this cell is dependent on the feature type selected. If the
feature type selected is a line, this number is the Z or horizontal coordinate of a line point
(LP). A line point is simply any point that lies somewhere on the line. Line points are only
used to draw and calculate the line, they are not part of the shape. Line points are not drawn
on the screen. Geometry Expert defaults to the LP/CP cell so it is more efficient when
creating lines to use line points whenever possible in order to reduce the number of key
strokes necessary. If the feature type selected is a circle, this number is the horizontal
coordinate of the centerpoint of the circle.
LP/CP Xd/Xr: The number entered in this cell is dependent on the feature type selected.
If the feature type selected is a line, this number is the Xd/Xr or vertical coordinate of a line
point. If the feature type selected is a circle, this number is the horizontal coordinate of the
centerpoint of the circle.
EXAMPLE: The row shown below will create a 90° (vertical) line that goes through
the point at Z 4. When defining either horizontal (0°/180°) or vertical (90°/270°)
lines, only one LP coordinate is required. Refer to the section on Half Points in this
chapter for more information.
EXAMPLE: The row shown below will create a circle with a radius of 2 and a
centerpoint at Z -3, Xd/Xr 2.
24
GFK-1701 G e o m e t r y C r e a t i o n ◆
Prompt: The information contained in the prompt indicates the status of the current row.
When a feature row is outlined in yellow, the prompt tells the user what specifications have
been entered for this feature and what will happen when the row is entered. If the feature row
is outlined in black indicating that more information is required, the prompt will tell the
user what additional information is required. The prompt also indicates if the system has auto-
matically deleted a cell value because the feature row contained too much information that
overdefined the feature. This aspect of Geometry Expert is referred to as the “auto delete”
function which is explained in the Expert Aids section of this chapter.
Close box: Clicking in this box will close Geometry Expert and allow the user to use the free
form CAD tools contained in the Geometry Creation palette. When Geometry Expert is closed,
all information is cleared out of the spreadsheet. When the Geometry Expert button is
depressed again, the spreadsheet will come up empty. In order to load or reload a shape into
the spreadsheet, simply double click on any feature of the shape while the spreadsheet is open
on the screen.
Size box : The size box allows the user to adjust the size of the Geometry Expert spreadsheet.
To adjust the size of the spreadsheet, click in the Size box and drag the window to the desired
size. The width cannot be changed, but the length can be adjusted.
Scroll Bar: The scroll bar and arrows allow the user to scroll through the rows contained in
the spreadsheet to make adjustments and check the values entered. This is useful if the spread-
sheet needs to stay relatively small to fit on the screen, and/or if it contains many features.
EXPERT AIDS
There are several items built in to Geometry Expert that are designed to guide the user
through geometry creation. They include prompting, auto delete, and error balloons.
Prompting
The prompting information appears across the bottom of the Geometry Expert spreadsheet.
The prompt tells the user what actions are being taken by the system based on the information
provided by the user. The user should be able to follow the prompts through the creation process to
get a good idea of what is happening.
Auto Delete
The auto delete function of Geometry Expert is intended to reduce errors resulting from
features being overdefined because too much information has been entered in the feature row.
Geometry Expert is designed so that the user need only enter the minimum amount of information
to define a feature. The system will automatically delete the first entry made in the feature row
when the feature is overdefined. Auto delete is necessary in order to facilitate the associative
capabilities of Geometry Expert. Note that the default values, such as the line angle, are considered
the first entry rather than any information entered by the user. The prompt will indicate what
information is being deleted.
25
◆ L e v e l 0 T u r n i n g GFK-1701
Error Balloons
Geometry Expert also contains Error Balloons which appear on the screen whenever a
problem occurs. The most common error messages appear when the system requires more
information for a feature being entered. For example, if a line needs another value for an end point,
an Error Balloon will come up indicating that a V or H value is needed to calculate the end point.
The Error Balloons and Prompting use the letters V and H, indicating Vertical and Horizontal.
Another common error message indicates that the feature being defined cannot intersect with
the previous feature. The non-intersecting feature can still be created, but the message indicates to
the user that the continuity of the shape has been broken and the subsequent features being created
will not connect to the existing shape.
ADDITIONAL INFORMATION
Defaults
When entering features in the Geometry Expert spreadsheet, the system contains defaults for
the feature type and line angle. The standard feature type default is a line. When Geometry Expert
defaults to a line, it also enters an angle value, either 90°/270° or 0°/180°, depending on the angle
of the last line entered. Sometimes a line is not a possible feature type option, in which case the
system defaults to an arc. This only occurs when the previous feature is a floating line. Geometry
Expert dimensions the line according to the preceding and following feature specifications.
Floating features are not drawn on the screen until the system contains the necessary information.
Post Targeting
Despite all of its expertise, Geometry Expert can’t always know the correct intersection point
to use for a connector. When there are two or more, equally valid points of intersection, the system
will draw both points. This is referred to as post targeting. When post targeting is required, a
dialog will come up that asks the user to select the appropriate point and click on the OK button.
Once the user has selected the desired intersection point, Geometry Expert will make the
appropriate connection and continue along in the spreadsheet defining and connecting features.
The Edit menu contains an item that will change the intersection point selected in a post
targeting dialog to the other possible point of intersection. The menu item toggles between Use
Intersection #1 and Use Intersection #2, depending on the point selected and where it lies along the
path of the shape. This option will be an active item when a feature that required post targeting is
selected on the screen.
Half Points
In certain cases, only one coordinate, either the horizontal or vertical, is required to define the
feature. This is referred to as a half point case. Half points are valid when Geometry Expert is able
to calculate the other half of the coordinate value from information contained in the spreadsheet.
(Either preceding or following features).
When a valid half point is entered, the row will be highlighted in yellow, allowing the user to
enter the feature row. If the half point entered is not valid, the row will be highlighted in black and
the prompt will indicate what additional information is necessary to enter the row. If an incomplete
row is entered, an error ballon will come up indicating what additional information is required.
There are three cases where half points are valid. They are listed and explained below.
26
GFK-1701 G e o m e t r y C r e a t i o n ◆
Half Line Point: A half line point is valid only when creating either a horizontal line (angle
value = 0° or 180°) or vertical line (angle value = 90° or 270°). If creating a horizontal line, a
V coordinate must be given for a valid half line point. If creating a vertical line, an H coordi-
nate must be given for a valid half line point. Line points are not part of the shape but are
only used to calculate the position of the line.
Half End Point: A half end point is only valid if the line is otherwise completely defined.
Given either the vertical or horizontal coordinate of the end point along with the other informa-
tion that defines the line, the system can calculate the other half of the end point. If a half end
point is used in the case of 0°/180° or 90°/270° lines, the half end point will function like a half
line point in that an end point will not be drawn, although the correct line will be created.
Half Center Point: A half center point is valid when a circle has a radius value and is tangent to
the preceding feature. (There must be a preceding feature). Given the radius and the vertical
or horizontal component of the centerpoint, the system can calculate the other half of the
centerpoint by the assumed tangencies.
Floating Features
Floating features are features whose defining row does not contain all of the information
necessary to draw the feature. Floating feature rows are different from incomplete feature rows.
With floating feature rows, the information contained in the current feature row and the preceding
rows is inadequate to completely define the feature and draw it. However, subsequent features,
defined in following rows, could provide the necessary information to define the floating feature.
Floating feature rows are outlined in yellow and can be entered.
Incomplete feature rows do not contain enough information to create the feature, and no
amount of information entered in following rows will make the feature definable. Incomplete
feature rows are outlined in black and cannot be entered without getting error messages.
Again, the row outline and the prompting information will indicate if the feature row can be
entered; and if it is, how the floating feature will be incorporated into the shape after later features
have been defined.
27
◆ L e v e l 0 T u r n i n g GFK-1701
calculate features that follow it in the spreadsheet. As the prompts indicate, Geometry Expert
completely ignores fillets (and chamfers) when calculating what information is necessary to define
features. When the prompt displays information about the interaction between the current feature
and the previous feature, fillets will be ignored.
An arc with only a radius value is created tangent to two other features. These two features
do not have to intersect. The arc is treated as an actual feature and can be used when calculating
other features of the shape.
This is particularly important when dealing with floating lines (lines with limited information)
that have specific tangency requirements. Geometry Expert assumes that floating lines are going to
be made tangent to the preceding feature. In most cases this is adequate, but sometimes a floating
line is supposed to intersect the previous circle and be tangent to the next circle. This is called a
"forward" tangency.
In the case of forward tangencies, if there is a radius between the previous circle and the
floating line, then an arc, rather than a fillet, must be used in order to allow for the necessary
tangency calculation. The line will be made tangent to both the arc used as a fillet and the next arc.
A fillet cannot be used in this case because the fillet will be ignored by the system until the
intersection is completed, and the correct intersection cannot be created without the arc. If there is
no fillet, an arc with a radius of zero will need to be created. This will allow the system to create
the line tangent to the following circle, while creating a sharp point at the intersection of the
previous feature.
EDIT MENU
The Edit menu contains items that allow the user to adjust and
select items contained in the file. Each item found in this menu is
described below in the order it is encountered in the menu.
Undo: This item will undo the last action performed. Some actions
cannot be undone. When Undo is grayed out in the menu, the
previous action cannot be undone.
Cut: This function will delete any selected items, and copy these items
to the clipboard. The item(s) can then be placed in the same file using
the Paste function.
Copy: This function will make a duplicate of the selected items and copy it to the clipboard. The
item(s) can then be pasted in the same file.
28
GFK-1701 G e o m e t r y C r e a t i o n ◆
Paste: This function will place the contents of the clipboard in either the drawing window, if the
clipboard contains geometry, or an active text box, if the clipboard contains text. If another item is
selected when pasting, that item will be deleted and replaced by the contents of the clipboard.
Select All: This function will select all of the geometry contained in the current workgroup.
Deselect All: This item will deselect any geometry currently selected.
Insert Row: This item will insert a blank row in the spreadsheet above the current row selected.
When an inserted row contains the necessary information and is entered, the system will recalculate
the shape and attempt to incorporate the inserted feature into the existing shape, if possible.
Delete Row: This item will deselect the selected row from the spreadsheet. As soon as the row is
deleted, the system will adjust the remaining shape to maintain the appropriate connections, if
possible.
Use Intersection #1 (#2): This item will toggle between Use Intersection #1 and Use Intersection #2 in
the menu. This option enables the user to select different intersections between concurrent features in
the spreadsheet. This option is available when the feature defined by the current row intersects the
feature defined by the following row in two places. This item will change the point of intersection,
selected in a previous post targeting dialog, to the other possible choice.
Reverse All Rows: When this item is selected it will reverse the order of the rows in the spread sheet
which will change the direction of the shape as it is loaded in Geometry Expert. This is useful when
loading a shape that was imported or created using the Free Form CAD tools. When a shape that was
not created using Geometry Expert is loaded into the spreadsheet, the system decides whether to go
in a clockwise or counter-clockwise direction when placing the features into the spreadsheet. The
direction has the potential to affect the angle values of lines and the direction of arcs of the shape.
There are times when the system will load the shape in the opposite direction than desired. When the
shape has been loaded into the spreadsheet, select the Reverse all rows item to reverse the order of
features. This item is only available when the spreadsheet contains feature rows.
NOTE:The Select, Deselect and Redo All Ops items are only available with the Level 1 version of this
software.
29
◆ L e v e l 0 T u r n i n g GFK-1701
MODIFY MENU
The Modify menu contains items that give the user additional
methods for creating, positioning and duplicating geometry. The
Modify Menu is grayed out when the Geometry Expert spreadsheet is
open. To use the items in the menu, close the spreadsheet and it will
become available. The Operation Data item is explained in the
Machining Chapter.
All of the items under this menu, except Operation Data and
Move Part Origin, require geometry to be highlighted before their
function can be performed. The Operation Data menu item requires an
operation to be highlighted.
Each item found in this menu is described below in the order it is
found in the menu.
Duplicate And: This selection will perform the individual functions Duplicate
and then Force Depth, Mirror, 2d Rotate, Scale or Translate at one time.
First, the selected geometry will be duplicated. Then, depending on the
option selected, the selected geometry is moved to one or more new locations
based on the number typed in the times box. The specific button choices
work the same as the items detailed below.
Set Default: Selecting a point and then choosing Set Default will cause the selected points X, Y and Z
locations to appear as the default values in any other appropriate Modify menu dialog. This item is
useful if a drawn point is used to mirror around, rotate around, etc.
Mirror: This selection will move the selected geometry to the other side of
the axis or axes specified, around an axis point entered in the text boxes.
Clicking on the Process button will perform the mirroring function. This
dialog can remain on the screen for further use while other functions are
performed.
30
GFK-1701 G e o m e t r y C r e a t i o n ◆
Scale: This selection will change the size of the selected geometry by the
amount specified. The value typed in the Amount box is a ratio of 1, 1
being full size. The inches to mm or mm to inches buttons will change the
geometry to the opposite numerical type. Clicking on the Process button
will perform the scaling function. This dialog can remain on the screen for
further use while other functions are performed.
Translate: This selection will move the selected geometry, by the specified
amount. Clicking on the Process button will perform the translating
function. This dialog can remain on the screen for further use while other
functions are performed.
Move Part Origin: This selection will move ALL the geometry incrementally by
the values typed in the Z and X boxes. The current location of Z0, X0 will
change incrementally by the values in this dialog and a new Z0, X0 will be
established. Clicking on the Process button will move the origin. This dialog
can remain on the screen for further use while other functions are performed.
NOTE: The Force Depth, Sort, Change CS XYZ and Change CS HVD items are only available with the
Level 1 version of this software.
31
◆ L e v e l 0 T u r n i n g GFK-1701
W O R K G R O U P S U M M A RY
Selecting Workgroup Summary from the part menu (title of this
menu will be the name of the part) will bring up the Workgroup
Summary dialog which provides information in spreadsheet form
about all features and points contained in the current workgroup.
When the Workgroup summary is open it can be printed by selecting
the Workgroup Summary item from the Print submenu under the File menu.
P R I N T I N G T H E PA RT G E O M E T RY
After the part geometry has been created, it can be printed. Geometry can either be printed in
black and white or color. When the desired geometry is on the screen, choose Drawing from the
Print sub-menu under the File menu. To adjust the way the image will print, choose Printing from
the Preferences sub-menu in the File menu. The Printing Preferences dialog, shown below, allows
the user to specify how the software will handle the background color. If the printer being used is a
black and white printer, choose the Black on White option to ensure that all portions of geometry,
including those that are a light color, can be seen in the print.
OS For specific information regarding printing on the different operating systems, refer to the
Printing Appendix found at the end of this manual.
32
GFK-1701 G e o m e t r y C r e a t i o n ◆
G E O M E T RY E X E R C I S E
In this exercise, we will create a simple shaft containing only
horizontal and vertical lines. Because of the feature type defaults and
automatic angle toggling, the creation of a simple shaft can be done
in a few minutes using Geometry Expert. The part print for this
exercise is provided at the end of this section.
33
◆ L e v e l 0 T u r n i n g GFK-1701
When you save files you want to make sure that you are saving them
in the appropriate location on your hard drive. You may need to
change drives and/or directories or folders in order to save the file in
the desired place.
The stock values entered are slightly larger than the part dimensions
so that we can see all of the geometry within the stock outline.
34
GFK-1701 G e o m e t r y C r e a t i o n ◆
When all the information about the part has been entered, close this
dialog. The information contained in it may be changed (edited) at
any time, simply by clicking on the Document Control button and
entering the new information.
• Close the Document Control dialog by clicking twice in the close box in the
upper left hand corner of the dialog.
35
◆ L e v e l 0 T u r n i n g GFK-1701
A stock outline is drawn with a “+” that signifies the origin of the
part which is located at Z0, X0. Your screen should now look like
the picture shown below.
36
GFK-1701 G e o m e t r y C r e a t i o n ◆
Notice that when the spreadsheet comes up, the feature type selected
is a line, and the angle value is 90°. For this first exercise, we will
only create vertical and horizontal lines. Therefore, the only values
that we will need to enter are line points because the default settings
for the feature type and line angle will be correct for the shape we are
creating.
37
◆ L e v e l 0 T u r n i n g GFK-1701
Once the line point is entered, the current row becomes highlighted in
yellow indicating that it now contains enough information to define
the feature. When the current row is highlighted in yellow, the
prompting information states what will happen when the user hits
enter.
When creating a new row, hitting the enter or return key will create
the feature and move the current row of the spreadsheet down one. If
you are working on existing rows, entering the row will not move the
current row down in the spreadsheet, it will only make the necessary
changes. The arrow keys or the cursor must be used to move up and
down within existing rows of the spreadsheet.
When the row is entered, the line is drawn on the screen and the
current row of the spreadsheet moves down one. The second feature
row has a line selected for the feature type and the angle is 180°. The
system angle defaults toggle between 0°/180° and 90°/270°and place
the cursor in the appropriate cell.
Current
Row
38
GFK-1701 G e o m e t r y C r e a t i o n ◆
The two lines are connected. Connected features have a blue square
(connector point) drawn at their intersection or tangency. When a
feature has two connector points, it becomes blue and trims.
Geometry Expert automatically connects features as they are drawn.
If two concurrent features do not have a point of intersection or
tangency, the system produces an error message indicating that the
previous feature can not intersect with the current feature.
Current
Row
Notice that the line angle has once again toggled to 90°.
The horizontal line is now fully connected, and as a result turns blue
and trims.
39
◆ L e v e l 0 T u r n i n g GFK-1701
Current
Row
Current
Row
Current
Row
40
GFK-1701 G e o m e t r y C r e a t i o n ◆
Current
Row
Current
Row
41
◆ L e v e l 0 T u r n i n g GFK-1701
Current
Row
Current
Row
42
GFK-1701 G e o m e t r y C r e a t i o n ◆
Current
Row
Current
Row
Current
Row
43
◆ L e v e l 0 T u r n i n g GFK-1701
Current
Row
Current
Row
44
GFK-1701 G e o m e t r y C r e a t i o n ◆
Current
Row
Current
Row
Current
Row
45
◆ L e v e l 0 T u r n i n g GFK-1701
Current
Row
Current
Row
46
GFK-1701 G e o m e t r y C r e a t i o n ◆
• Click on the feature type button and drag the cursor to the Close Shape
option so that it becomes depressed. Release the mouse button.
Current
Row
The Close Shape feature type connects the first feature and the last
feature at their point of intersection or tangency by creating a
connector point. No information other than the feature type needs to
be entered, and therefore all the cells in a Close Shape feature row are
grayed out. Closing the shape will usually be the final step when
creating a shape using Geometry Expert.
The shaft is complete and fully connected. The final shape should
look like the picture shown below.
47
◆
48
PA RT P R I N T # 1 : S H A F T
L e v e l
0
7.5
7.0
6.0
5.0
T u r n i n g
3.75
3.0
3.25
3.0 2.0
2.5
1.5 x 3
4.0 1.0
7.25
GFK-1701
GFK-1701 T o o l C r e a t i o n ◆
CHAPTER 5 : T o o l C r e a t i o n
Depressing the Tool List Button in the Top Level Palette will bring up the Tool List.
The Tool List can hold up to 999 tools in a part file. Double-clicking on a tile location will
bring up a Tool Creation Dialog. This dialog is used to create and modify tools. Once the
tool information has been entered and the dialog closed, a Tool Tile will be created which
displays the tool type and tool diameter. To index through the various tools that have been
created, click on the scroll arrows located at the top and bottom of the Tool List.
Tools can be reorganized in the list at any time, even after operations have been
created, without reprocessing the operations. To reorganize the order of tools, click once
on the Tool Tile to be moved and drag it to an insertion point. The system will
automatically adjust the operations to reflect the change in tool order and number. For
more information on Tile Lists refer to the Interface Chapter.
Tool specifications can be modified at any point during part creation. However, if operations
have been created using the tool, those operations must be reprocessed. To reprocess an operation,
double-click on the Operation Tile in the Operation List and click on the Redo it button. The new
tool specifications will be incorporated into the new operation(s) toolpath.
T O O L C R E AT I O N D I A L O G
All tools are created using the Tool Creation Dialog shown below. Each of the items contained
in the dialog is described in the following section.
Tool Type Button
Insert Spec
Pop-up Menus
Insert Orientation
Diagram
Insert Type
Holder Specs
Spindle Direction
Tool Length
Offset #
Tool Material
Pop-up Menu
49
◆ L e v e l 0 T u r n i n g GFK-1701
Insert Type: This area is used to select the type of insert used with the tool
holder. The Insert Specs information will change depending on the
currently selected insert.
Tool Type Button: This button is used to toggle between mill tools and lathe inserts. Mill tools
should only be used with the drilling function.
Insert Specs: This information will change depending on the currently selected insert type. Each of the
pop-up menus will limit the selections available in the pop-up menus that follow it. For example,
selecting a Tip Radius will limit the number of available IC’s and Thicknesses. Selecting an IC will
further limit the number of Thicknesses available. These settings will limit the number of available
tool holders and boring bars in the holder diagram. If no tool holders or boring bars are available, the
None choice will automatically be selected.
TYPE 1 INSERTS
80° Diamond
55° Diamond
35° Diamond
Square
Triangle
Pentagon
Trigon
50
GFK-1701 T o o l C r e a t i o n ◆
TYPE 2 INSERTS
Round
TYPE 3 INSERTS
55° Parallelogram
TYPE 4 INSERTS
Rectangle
TYPE 5 INSERTS
Cut Off
51
◆ L e v e l 0 T u r n i n g GFK-1701
TYPE 6 INSERTS
Groove
Tip Length
Insert Width
Tip Radius
Tip Width
Face Angle
The diagram above explains all of the values needed for a groove insert. When the Tip Width,
Tip Radius and Insert Width are selected, the system will calculate the values for the Face
Angle and Tip Length. If Full Radius is selected, only inserts with a Tip Width equal to twice
the Tip Radius will be available.
TYPE 7 INSERTS
52
GFK-1701 T o o l C r e a t i o n ◆
TYPE 8 INSERTS
TYPE 9 INSERTS
Insert Orientation diagram: This diagram is used to specify the orientation of the
insert in the tool holder or boring bar. Changing the information will not affect the
availability of other items in the dialog, but it will change the orientation of the
drawing in the Holder diagram.
Holder Specs: This information is determined by the currently selected holder in the
Holder Diagram. It cannot be modified.
53
◆ L e v e l 0 T u r n i n g GFK-1701
Offset #: Normally the offset number of the tool is determined by its location in the Tool List. This
box allows the user to override that default with a different number.
Tool Material: This is a pop-up menu used to specify the material of the tool. The information given
here is used by the Material Database as another factor to determine speeds and feeds.
Comment: This is a comment associated with the tool. It will be output in the finished code at the
beginning of every operation that uses this tool.
54
GFK-1701 T o o l C r e a t i o n ◆
T O O L L I S T S U M M A RY
Selecting Tool List Summary from the part menu (title of this menu
is the name of the currently open part) will bring up the Tool List
Summary dialog which provides information in spreadsheet form
about each tool contained in the Tool list. The information in the
dialog can be printed. To print the summary, select Tool List
Summary from the Print sub-menu in the File menu.
55
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 6 : M a c h i n i n g
M A C H I N I N G O V E RV I E W
Depressing the Machining button will bring up the Process list, the Machining palette,
and the Operation list. The Process list is used to create sets of operations to be
performed on cut shapes. The Machining palette contains Function tiles, that when used
in conjunction with Tool tiles, create Process tiles. The Process list is a “staging area”
that is used to generate finished operations which contain the toolpaths for cutting the
part. When an operation is finished and placed in the Operation list, the items in the
Process list can be thrown away or re-used with a different cut shape. The Operation list
contains the completed operations that will be output during post processing.
C R E AT I N G A N O P E R AT I O N
Each tile in the Process list will be performed on the selected geometry. A Process tile is
created by dragging a Function tile from the Machining palette and a Tool tile from the Tool list to
the same location in the Process list. They can be dragged in any order. When a Process tile is
complete, the appropriate Process dialog will appear. This dialog contains detailed information
about the way the operation’s toolpath will be created.
Contouring and Roughing functions require that geometry be selected to act as the cut shape
for the operation. Machining markers are used to select the portions of the geometry to be used as
the cut shape when creating a toolpath. The markers will appear on the geometry when it is selected.
If a drilling or threading function is being used, no geometry is required to create an operation.
After the information in the process dialog has been entered, place the machining markers in the
correct locations on the geometry. Machining markers are not used for drilling and threading
functions. Clicking on the Do it button will create an operation(s). The operation(s) will be placed
in the Operation list. If any completed operations are selected (in yellow), the Do it button becomes
the Redo it button. If the Redo it button is depressed, the selected operations will be replaced by the
new operations. Clicking on an empty Operation location, or clicking on an insertion point between
Operation locations will deselect all the operations.
Operations contain the finished toolpaths. A toolpath consists of the actual moves the tool will
make. The toolpath is based on the cut shape.
W H AT I S A C U T S H A P E ?
A cut shape is used to generate a toolpath. It is not specifically drawn on the screen, but can be
visualized as the finished shape left after the removal of material by the toolpath. A cut shape is used
to create a toolpath, instead of the original geometry, because programming the toolpath to the
geometry as it is defined on the blueprint will usually gouge the part. The software automatically
generates the cut shape. Various specifications and limitations are taken into consideration in the
creation of the cut shape.
The machining markers (the start and end point and start and end feature markers) allow the
user to specify the portion of geometry (or the entire shape) that will act as the initial outline of the
cut shape. The system then takes into account the physical attributes of the tool being used in the
56
GFK-1701 M a c h i n i n g ◆
process, such as insert type, tool holder, relief specs, etc in order to prevent possible tool interference
when applying the tool to the cut shape being machined. The cut shape is further governed by
information entered in the Process dialog, such as Entry/Exit Radius, Stock, Shape Axes, etc. The
system employs the concept of a cut shape so that it is not necessary to create different geometry for
different operations in order to avoid gouging the part.
M U LT I P L E P R O C E S S P R O G R A M M I N G
If more than one Process tile is in the Process list when the Do it button is depressed, multiple
operations will be created. Each operation must use the same geometry. When the finished
operations are placed in the Operation list, they will be “linked”. This means that if one operation is
double-clicked, all operations will be selected that were created with the same Process list as the
operation selected. This allows changes to geometry to be handled much easier. Linked operations
can be moved around in the process list without losing the link. A typical use for multiple processes
is roughing and finishing the same shape with the same or different tools.
The Material Only option available in the Contouring and Roughing Process dialogs is
particularly useful when doing multiple process programming. Material Only provides for “no air
cutting.” When selected, the system optimizes the toolpaths created by only making feed moves
where there is material that needs to be removed. The system takes into account the material
conditions in terms of what has already been cut in previous operations, including those contained in
the same process list.
M O D I F Y I N G A N O P E R AT I O N
Double-clicking on an item in the Operation list will re-create all of the information in the
Process list. It will also select the geometry and place the markers exactly as they were when the Do
it button was pressed. Any operations that were created at the same time as the selected operation
will become selected and their information placed in the process list as well. The Do it button will be
replaced by a Redo it button. Click on the Redo it button after the changes have been made. This
will replace all selected operations in the Operation list with the newly created operations.
M A C H I N I N G PA L E T T E
Each tile in the Machining palette has a different function. The Contouring function is used for
taking a single finish pass. The Roughing function is used for taking multiple passes. The
Threading function is used for making different types of threads. The Drilling function is used for
drilling a hole at X = 0.
The order of machining in the finished NC program is the same as the Operation list. This
means that the order of Operation tiles in the Operation list is very important. Efficient use of
Multiple Process Programming may produce operations in a less than optimal machining order. The
operations list can be organized as the part is being created or when all operations to cut the part have
been completed. Clicking on the Sort Ops button reorganizes the operations by tool number and
creation order. Operations created in the same process list will maintain their order to ensure that
that finishing passes cannot be moved in front of roughing passes, etc. The operations list can also
be manually rearranged by moving tiles to different locations in the list.
57
◆ L e v e l 0 T u r n i n g GFK-1701
While the operations list can be reorganized to create a more optimal machining order, there are
some considerations that must be made. When using the Auto Clearance option and/or the Material
Only option, the system takes into account the material conditions when it creates the positioning
moves and toolpath for each operation. Changing the order of operations has the potential to change
the initial material conditions for existing operations. If the order of operations is changed or
operations are added or removed from the list, the toolpaths and positioning moves should be
checked. Rendering the part is a good way to check if changes need to be made to the tool moves
due to tool interference or unnecessary or incorrect positioning moves. If adjustments need to be
made the operations must be reprocessed. When the operations are reprocessed, the system will
recalculate all of the toolpaths and positioning moves based on the new order of operations.
PROCESS DIALOGS
Process dialogs appear on the screen when a function tile from the Machining palette and a
Tool tile from the Tool list are placed in a Process list location. There are four types of Process
dialogs, to correspond to the four types of functions available in the Machining palette. They
include: Contour Process, Rough Process, Thread Process, and Drilling Process. The options
available with each of these processes is described in this section.
CONTOUR PROCESS
The Contour process is used to take a single pass along a shape. When a Contour Function tile
is combined with a tile from the Tool list, the following process dialog will appear.
58
GFK-1701 M a c h i n i n g ◆
Approach Type: This should be the first selection made in any process dialog.
The Approach Type selection designates the axis (Z or X) along which the
tool will approach the part. The OD and Front ID options specify that the
tool approach and retract along the X axis, while the Front Face option
requires that the tool approach and retract along the Z axis. Also, selecting one of these radio buttons
will change the Clearance diagram that appears in the middle of the Process dialog.
Cut Direction: These radio buttons indicate the direction the tool will move along the
designated cut shape. If the Forward option is selected the tool will move from the
start point to the end point of the selected cut shape as designated by the machining
markers. If the Reverse option is selected, the tool will move from the end point to the start point of
the selected cut shape.
Entry Move: The Entry Move radio buttons instruct the system to
create additional geometry that will be added to the toolpath of a
particular process. When the first option is selected, a 90° arc of
the specified radius value will be added to the toolpath. This arc
will be tangent to the start feature at the start point. If a value is
entered in the Line text box, a line of the specified length will be
created tangent to the arc. When the second option is selected, a
line of the specified length will be added to the cut shape. This line will be perpendicular to the start
feature at the start point.
Exit Move: The Exit Move radio buttons instruct the system to
create additional geometry that will be added to the toolpath of a
particular process. When the first option is selected, a 90° arc of
the specified radius value will be added to the toolpath. This arc
will be tangent to the end feature at the end point. If a value is
entered in the Line text box, a line of the specified length will be
created tangent to the arc. When the second option is selected, a
line of the specified length will be added to the cut shape. This line will be perpendicular to the end
feature at the end point.
59
◆ L e v e l 0 T u r n i n g GFK-1701
Shape Axes: The Shape Axes buttons allow the user to regulate the
axes and directions of the cut shape. Axes are selected when the
button beside them is depressed and contains a red dot.
Deselecting an axis will prevent cut shape moves in that axis direction. The default settings should
have all axes turned on.
60
GFK-1701 M a c h i n i n g ◆
ROUGH PROCESS
These processes are used to take multiple passes on a shape. When this tile is combined with a
tile from the Tool list, the following process dialog will appear.
Cut Direction: These radio buttons indicate the direction the tool will move
along the designated cut shape. If the Forward option is selected, the tool
will move from the start point to the end point of the selected cut shape as
designated by the machining markers. If the Reverse option is selected, the
tool will move from the end point to the start point of the selected cut shape.
61
◆ L e v e l 0 T u r n i n g GFK-1701
Rough Type: The Rough Type radio buttons indicate what type
of roughing cycle will be used for the current process. The
three available rough types are Turn, Plunge, and Pattern Shift.
Each rough type has a different corresponding Clearance
diagram. The Plunge and Pattern Shift options will bring up
dialogs asking for additional information specific to the
selected rough cycle. The information required for each rough
type is detailed below.
Turn Rough: When the Turn option is selected, a Cut Depth amount must be entered that
specifies the depth of cut the tool will make on each roughing pass. Depending on the
Approach Type selected, the cut depth will either be an Xr or Z value.
62
GFK-1701 M a c h i n i n g ◆
Plunge Rough: When the Plunge option is selected, the Plunge dialog, described below, will
appear on the screen.
63
◆ L e v e l 0 T u r n i n g GFK-1701
Peck Full Out: This option designates that the first plunge
be a peck. The user specifies a Peck amount and a
Clearance amount. Because it is a Peck Full Out, after
each peck, the tool will retract all the way out of the
groove to the clearance position. The tool will then
reenter the part and begin its peck move a clearance
distance away from the remaining material.
Pattern Shift Rough: When the Pattern Shift option is selected, the Pattern Shift dialog will
come up on the screen.
64
GFK-1701 M a c h i n i n g ◆
65
◆ L e v e l 0 T u r n i n g GFK-1701
Shape Axes: The Shape Axes buttons allow the user to regulate the
axes and directions of the cut shape. Axes are “on” when the button
beside them is depressed and contains a red dot. Deselecting an
axis will prevent cut shape moves in that axis direction. The default settings should have all axes
clicked on.
THREAD PROCESS
When the Threading function tile is combined with a Tool Tile, the Thread Process Dialog will
appear on the screen, as shown below.
66
GFK-1701 M a c h i n i n g ◆
Approach Type: With both selections in the threading process, the approach is along
the X axis. These selections allow the user to determine whether the thread will
be located on the OD or ID of the part. The Clearance/Thread diagram will
change according to the choice made here.
Style: The choices for Style are contained in a pop-up menu and
allow the user to specify what style of thread will be cut. The
selection made here designates the appropriate thread form for control of calculations.
Nominal Xd: The value entered in this text box is the diameter
location of the thread as specified on the part blueprint.
TPI: The value entered in this text box specifies the number of
threads per inch, or threads per millimeter for metric parts.
Major Xd: The value in this text box automatically defaults to the value
entered for the Nominal Xd, however, it can be changed to a value of the
user’s choice. Cutting begins at this diameter on an OD thread.
Minor Xd: The value in this text box defaults to a calculated value
based on the nominal Xd and the desired pitch. Again, it may be
changed to a value of the user’s choice. Cutting begins at this diameter on an ID thread.
67
◆ L e v e l 0 T u r n i n g GFK-1701
Depth of Cut: The selections made in this box allow the user to
designate the cut depth for each pass of the threading operation.
The One Finish Pass option specifies that the tool will make a
single pass over the thread. Its primary use is to remove burrs or
small excesses of material on an existing thread. The Const Cut
selection allows the user to designate the Depth of Cut that the
threading tool will make on each pass. The value is measured as
a radius and is entered in the text box labeled 1st. The Const
Load selection allows the user to specify the depth of the cut
made on the first pass. This value is also measured as a radius and entered in the text box labeled
1st. The amount of material (the load) removed for that depth of cut will be calculated, and on each
successive pass, the same amount of material will be removed.
The Last Cut option is selected to prevent any cut from removing less than a given amount of
material on the last pass. The value entered is measured as a radius value and specifies the minimum
cut for the constant load to diminish to. The Spring Pass option can be used in conjunction with any
of the depth of cut selections. It will create additional passes equal to the number entered, after the
thread has been cut.
Speed:RPM: The value entered here is the rate of the spindle measured
in revolutions per minute.
DRILLING PROCESS
When this tile is combined with a tile from the Tool list, the following process dialog will
appear.
68
GFK-1701 M a c h i n i n g ◆
Entry/Exit Cycle: The selections made here determine the cycle the
drill will use to make its entry and exit moves. The choices
include: Feed In-Rapid Out, Feed In-Feed Out, Tap, Rigid Tap,
Peck Full Out, and Peck Chip Breaker.
Clearance: This text box is only active (black, instead of grayed out) if
Peck Full Out is the selected Entry/Exit cycle. The value entered
specifies the incremental distance away from the material that the tool will start its next peck from.
Peck: This text box is only active when either Peck Full Out or Peck
Chip Breaker is the selected Entry/Exit cycle. The value entered here
specifies the depth increment the tool will drill on each peck.
Retract: This text box is only active if Peck Chip Breaker is the selected
Entry/Exit cycle. The value entered here specifies the amount the tool
will retract after each peck.
Speed: RPM: The value entered here is the rate of the spindle
measured in revolutions per minute.
69
◆ L e v e l 0 T u r n i n g GFK-1701
Feed: Plunge: This value specifies the feed rate of the tool and
is measured in inches per revolution.
CLEARANCE MOVES
This section contains information and diagrams on rapiding and feeding around lathe parts. It is
very important when working with lathes to avoid tool interference with the part, the spindle, etc.,
while at the same time, quickly and efficiently maneuvering around the part. Clearance positioning
is the term used for various positions the tool will move to when not actually cutting the part.
The primary tool change position is specified in the Document Control dialog (shown below).
If Tool Change is turned off, it is assumed that the finished code will be manually edited to handle
the tool change. Otherwise, the tool will start at the Tool Change position entered here.
In addition to specifying the position of the turret when tools are changed, the Document
Control dialog provides the user with two options for handling part clearance. The selection made
will determine how the system will calculate positioning moves between operations.
AUTO CLEARANCE
The Auto Clearance option performs several functions when it is turned on. It will calculate the
part clearances, in both Z and X, that are used to position the tool between each operation. These
positioning moves will be dynamically calculated for each operation. This means that as the stock
conditions of the part change as material is removed, the clearance positions will adjust accordingly.
When Auto Clearance is on, the system will also take into account where the tool needs to be to
begin the next operations’ toolpath when calculating the positioning moves. Additionally, the Auto
Clearance function may add entry and/or exit moves to the toolpath in order to safely maneuver
around the part.
The Auto Clearance option requires the user to enter an offset amount from the part stock that
the system uses to calculate the clearance positioning moves between operations. Because the stock
conditions are constantly changing as material is removed from the part, in order to optimize the
toolpaths, an offset amount is used for positioning rather than absolute positions. Fixed clearance,
which is used when Auto Clearance is turned off, uses absolute positions.
70
GFK-1701 M a c h i n i n g ◆
FIXED CLEARANCE
When the Auto Clearance option is turned off, fixed clearance positions are used by the system
to calculate clearance moves. The user must enter an overall part clearance in the Document Control
dialog, as well as, entry and exit clearance positions in the process dialogs for each operation.
The overall part clearance is entered in the Document Control dialog in the X and Z text boxes
that become active when Auto Clearance is turned off. They designate the position the tool will
rapid to and from during a tool change. This position will also be used moving from one approach
type to another between operations that use the same tool. The X and Z absolute position specified
in these two text boxes are locations the tool can rapid to when moving around the part. One or both
of these fixed positions are used whenever a tool is moving to the start point of the toolpath or
exiting from the toolpath. Where the tool moves when approaching and retracting from the part
depends on the Approach Type selected and the positions specified in the Clearance diagrams in the
Process dialog.
The Approach Type selections are located in the upper left corner of the Process dialog. The
tool can approach the part along two different axes; either X or Z. The tool will approach the part
along the Z axis if face is selected. The tool will approach the part in X if OD or ID is selected.
When a drill process is selected the Approach Type is automatically set to Front Face. Only one
selection can be made for each process.
Once the Approach Type is selected, the correct Clearance diagram appears in the Process
dialog. The boxes with the arrows next to them represent the Entry and Exit Clearance positions that
the tool may use when approaching and retracting from the part. The entry and exit clearance
positions are only required when Auto Clearance is turned off.
When a Turn roughing cycle is selected, an additional move will be added between the Entry
Clearance Position and the X Stock Start Position. When a Pattern Shift roughing cycle is selected,
an additional move will be added between the Entry Clearance Position and the contour Start Point.
CLEARANCE DIAGRAMS
The tool will use some or all of the clearance positions depending on which Approach Type is
selected. When Auto Clearance is selected the tool will still move to the positions indicated in the
diagrams shown below. However, the system will calculate these positions and they will change as
the material conditions of the part change. Also, when Auto Clearance is on, the system may add
additional entry and exit moves as necessary to prevent tool interference. Following are thirteen
pictures that detail how the tool will move around the part based on the different Approach Type
selections.
71
◆ L e v e l 0 T u r n i n g GFK-1701
SP Xd
SP Z
72
GFK-1701 M a c h i n i n g ◆
SP Xd
(SP Z, Entry Clearance Xd) (Entry Clearance Xd, Part Clearance Plane Z)
EP Xd
73
◆ L e v e l 0 T u r n i n g GFK-1701
EP Z
EP Xd
(EP Z, Exit Clearance Xd) (Exit Clearance Xd, Part Clearance Plane Z)
74
GFK-1701 M a c h i n i n g ◆
OD to Face
(Part Clearance Dia Xd, Part Clearance Plane Z)
(EP Z, Part Clearance Dia Xd)
EP Xd
OD to OD
(SP Z, Exit Clearance Xd) (EP Z, Exit Clearance Xd)
SP Xd EP Xd
Op 2 Op 1
75
◆ L e v e l 0 T u r n i n g GFK-1701
Face to ID
SP Xd
Face to OD
(Part Clearance Dia Xd, Part Clearance Plane Z)
(SP Z, Part Clearance Dia Xd)
SP Xd
Op 2
Op 1 EP Z
76
GFK-1701 M a c h i n i n g ◆
Face to Face
Op 1
EP Z
(EP Xd, Exit Clearance Z)
ID to Face
EP Xd
(EP Z, Exit Clearance Xd) (Exit Clearance Xd, Part Clearance Plane Z)
77
◆ L e v e l 0 T u r n i n g GFK-1701
ID to ID
Op 2 Op 1
SP Xd EP Xd
(SP Xd, Entry Clearance Xd)
MACHINING MARKERS
Machining Markers allow the user to specify the start and end feature and start and end point of
the cut shape, the cut direction, and the offset position of the tool. These markers appear on the
screen when geometry is selected for contouring and roughing processes.
Start Feature: The geometry feature (line or circle) on which the tool will start cutting.
Start Point: The point on the Start Feature where the tool will start cutting.
End Feature: The geometry feature on which the tool will stop cutting.
End Point: The point on the End Feature where the tool will stop cutting.
Cutter Side and Direction: The circles represent the offset position of the tool with
regard to the cut shape. The two possible options are the inside of the cut shape
or the outside of the cut shape. The arrows indicate which direction the tool will
travel. Simply click on the desired circle and direction arrow.
78
GFK-1701 M a c h i n i n g ◆
SELECTED GEOMETRY
The machining markers allow the user to specify the portions of geometry to act as the outline
for the cut shape. When markers are present on geometry, the cut shape is indicated by a dark blue
color. When the cut shape is not the entire contour, the geometry not included as part of the cut
shape is drawn in light blue.
O P E R AT I O N D ATA
When an operation is selected (highlighted), Operation Data becomes an active option under
the Modify menu. An Operation dialog, shown on the following page, appears on the screen which
allows the user to enter an Operation comment and also Utility Data at the operation start and end.
Information entered in the Op Comment box will appear in the posted output before the selected
operation it refers to. Custom posts allow the user to input custom commands in the At Op Start
and At Op End boxes that will trigger actions inside the post processor. In addition, any text that
appears in quotes in the At Op Start and At Op End text boxes will appear in the posted output. Each
set of quotes will be on a separate line in the posted output.
79
◆ L e v e l 0 T u r n i n g GFK-1701
O P E R AT I O N S U M M A RY
Selecting Operation Summary from the part menu (the title of this
menu is the name of the current part) will bring up the Operation
Summary dialog. This dialog provides information in spread sheet
form about each operation in the program, including estimated cut
time and the distance traveled by the tool. The information in the
dialog can be printed. To print the summary, select Operation Summary from the Print sub-menu in
the File menu.
P R I N T I N G T H E T O O L PAT H
After the operation has been created and the toolpath drawn, it can be printed. Toolpaths can
either be printed in black and white or color. When the desired toolpath is on the screen, choose
Drawing from the Print sub-menu in the File menu. To adjust the way the image will print, choose
Printing from the Preferences sub-menu in the File menu. The Printing Preferences dialog, shown
on the following page, allows the user to specify how the software will handle the background color.
If the printer being used is a black and white printer, choose the Black on White option to ensure that
all portions of geometry, including those that are a light color, can be seen in the print.
80
GFK-1701 M a c h i n i n g ◆
OS For specific information regarding printing on the different operating systems, refer to the
Printing Appendix found at the end of this manual.
81
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 7 : V i e w C o n t r o l
V I E W I N G T H E PA RT
The system provides for dynamic viewing of the part in any planar orientation. The
View Control Palette allows the user to change the view of the part by either clicking on
buttons which provide standard view changes, such as the top and side view, or
maneuvering a small model of the part to any orientation. The part can be drawn,
machined and rendered in any view. The top view is recommended for creating geometry
and machining operations, while the isometric or “world” view is excellent for cut part
rendering.
V I E W C O N T R O L PA L E T T E
Depressing the View Control Button brings up the View Control Palette that is used for
changing the current view of the part. In the center of the palette is a “trackball”. Around the outside
of the trackball are additional buttons for controlling the view. The entire View Control Palette is
often referred to as the Trackball.
Top View
When the cursor is placed over the Trackball, the cursor changes into a hand which allows the
user to roll the Trackball and change the view. Holding down the mouse button and moving the
mouse will roll the Trackball. The black outlined box on the ball represents the orientation of the
part. The "T" identifies the top surface of the part. The dimensions of the box do not change with the
actual part size. Z is always the long axis and X is the short axis.
Once the desired view is obtained and the mouse button released, the part will be redrawn in the
new view. The ball has four small solid black rectangles around the inside ring of buttons (located at
12:00, 3:00, 6:00, 9:00). These are called trackball handles. These handles can be dragged for a
single axis view change. The View Control Palette can be moved to any location on the screen by
dragging its edge.
82
GFK-1701 V i e w C o n t r o l ◆
VIEW MENU
All of the buttons in the View Control Palette are also available as
items in the View menu. In addition, there are other items contained
in the menu that relate to the viewing and drawing of the part. Each
item in the View menu is described below.
Isometric View: This is a “world” view. The part is drawn such that the
part dimensions are all foreshortened equally.
Unzoom : Also known as no zoom. This sets the scale of the view to
the maximum size that the monitor will allow. It is based on the stock
size and the current view.
Redraw: This item refreshes the screen image allowing the user to get
a better indication of what is currently drawn on the screen.
Geometry, toolpaths, or the rendered part image can be redrawn using
this item.
Previous View: This item changes the current view to the last view that was worked in.
Zoom In: This item increases the scale of the view so the drawing gets bigger by 25% each time it is
selected.
Zoom Out: This item decreases the scale of the view so the drawing gets smaller by 25% each time it
is selected.
Labels: If this item is turned on, labels will be drawn next to every geometry feature drawn. Circles
will be labeled C#, Lines L#, and Points P#. The # is determined by the order the points and features
were created. It corresponds directly to the information shown in the Workgroup Summary.
Draw Points: If this item is turned off (not checked), all points will not be drawn. The default selection
has the Draw Points item turned on.
Extend Lines: When this item is turned on, all unconnected lines will extend to the edge of the stock. If
it is turned off, lines will only extend to the features they were created between.
83
◆ L e v e l 0 T u r n i n g GFK-1701
Show Stock & Origin: The default has this item turned on. If it is turned off, the gray outline of the
stock and the origin marker will not be drawn on the screen.
Show Geometry: This item redraws only points, lines and circles. It will draw geometry over the cut
part rendered image of the part.
Shrink Wrap: When this item is selected, the software will examine the geometry in all of the
workgroups and adjust the stock size to show all the geometry on the screen without excess blank
space.
NOTE: The Home, Show CS Grid, Show Selected WG and Hide Selected WG items are only available
with the Level 1 version of this software.
84
GFK-1701 C u t P a r t R e n d e r i n g ◆
CHAPTER 8 : C u t P a r t R e n d e r i n g
C U T PA RT R E N D E R I N G O V E RV I E W
Modeling is the process of defining a three dimensional object. Rendering is the
process of displaying a picture of this model. A cut part model is defined when the
operations necessary to machine a part have been created. The computer has 3D
knowledge of the inside of the model; even of the areas that are not visible.
The cut part rendering capability in the system is called Three Dimensional Real
Time Cut Part Rendering. Three dimensional refers to the the fact that the model can be
rotated around in space and viewed at any angle. Real Time refers to the speed at which
the part is rendered. The cutting action is rendered as it is calculated rather than calculating
the rendered image and then playing back a "movie", or just displaying a picture of the
finished model. Real Time does NOT mean actual feed rates are used. The tool is cutting as fast as
the computer can calculate the moves. Cut Part refers to watching the effect of the tools cutting, as
opposed to seeing only the finished picture. Seeing the cutting process is more valuable, in most
cases, than the finished picture. Rendering refers to the process of displaying the graphic image of
the cut part model defined by the machining operations.
All operations will be rendered in their current order. The rendering process will start over
whenever the view is changed or zoomed. Therefore, it is more efficient to select the desired view
before depressing the Cut Part Render Button. Selected operations will render in shades of yellow, all
others will render in shades of grey. Shades of red will be drawn when non-cutting tool surfaces or
rapid moves hit the material. Selected tools will be drawn in shades of yellow. Unselected tools will
be drawn in shades of grey. Smaller pictures will render faster and use less computer memory.
C U T PA RT R E N D E R I N G PA L E T T E
When the Cut Part Rendering Button is depressed, the Cut Part Rendering Palette appears on
the screen, and the stock shape will be displayed as a blue, 3D solid image. The Cut Part Rendering
Palette controls the cut part rendering process. The functions of the items in the palette are described
below.
Rewind Step Forward Next Operation
Operation Box Stop Play
Operation Box: This box displays the number of the current operation being rendered.
Rewind: This button sets the current operation to the first operation. If the Play button is down when
the Rewind button is depressed, the part will be redrawn.
85
◆ L e v e l 0 T u r n i n g GFK-1701
Stop : This button stops any rendering in progress and raises the Play button.
Step Forward: This button renders the next feature of the current operation. If the Play button is
depressed, it will be raised and rendering will be stopped at the end of the current feature.
Play: When the play button is depressed, the part will be rendered from the current feature of the
current operation as listed in the operation box. Rendering will continue until one of the other buttons
is depressed or the last feature of the last operation is rendered. The Stop and Step Forward buttons
stop the rendering and raise the Play button. The Next Operation and Rewind buttons will change the
current operation being rendered, but will not stop the rendering process. When the last feature of the
last operation is completed, rendering will stop, but the Play button will remain depressed. Anytime
the rendering process stops, hitting the Play button again will resume rendering from the current
location.
Next Operation: If the Play button is depressed, the current feature being rendered is finished and the
remaining features for that operation are skipped. The next feature to be rendered is the first feature
of the next operation. If the Play button is not depressed, the current operation is set to the next
operation. The Operation box will be updated, but nothing will be rendered until the Play button is
depressed again.
Throttle Control: Shows the current location of the Throttle slider. The plus side represents maximum
rendering speed, and the minus side the minimum. The location of the slider can be changed by
dragging it left or right. This can be done during the rendering process and the effects will be seen as
the slider is moved.
86
GFK-1701 C u t P a r t R e n d e r i n g ◆
During the cut part rendering process, if the screen is redrawn due to a view change or redraw,
the rendering process will start over from the first operation. Therefore, it is a good practice to set the
desired view before rendering the part.
When the rendering process is stopped by pressing either the Stop or Step Forward button, the
next time the part is rendered the system will automatically stop the rendering process in the same
location. User set stops are maintained by the system. Anytime the rendering process is stopped
simply click on the Play button to continue.
If the Play button is depressed when the Cut Part Rendering Button in the Top Level Palette is
raised, it will be depressed when the Cut Part Rendering Button is selected once again. This means
that the next time the Cut Part Rendering Button is depressed, the rendering process will
automatically start. If the view is exactly the same when the Cut Part Rendering Button is depressed
as it was when it was raised, the rendered part will immediately be drawn and any new or
“incremental” operations will be added.
87
◆ L e v e l 0 T u r n i n g GFK-1701
C U T PA RT R E N D E R I N G P R E F E R E N C E S
There is a Rendering option in the Preferences sub-menu under the File menu. If it is selected,
the following dialog box will appear.
By default, both options will be turned on. Turning off either or both will slightly decrease
rendering times and memory requirements. Turning off Smooth Shading will reduce the quality of
the cut part rendered image. If the Tool Drawing Enabled option is turned off, the rendering process
will always be shown with an invisible tool. The software must be restarted for the changes to take
effect.
P R I N T I N G T H E C U T PA RT R E N D E R E D I M A G E
After the Cut Part Rendering is complete, the rendered image can be printed in either black and
white or color. When the rendered image is on the screen, choose Drawing from the Print sub-menu
in the File menu. To adjust the way the image will print, choose Printing from the Preferences sub-
menu in the File menu. The Printing Preferences Dialog, shown below, allows the user to specify
how the software will handle the background color. If the printer being used is a black and white
printer, choose the Black on White option to ensure that all portions of the image, including those that
are a light color, can be seen in the print.
For specific information regarding printing on the different operating systems, refer to the
OS Printing Appendix found at the end of this manual.
88
GFK-1701 P o s t P r o c e s s i n g ◆
CHAPTER 9 : P o s t P r o c e s s i n g
P O S T P R O C E S S I N G O V E RV I E W
Once the operations to machine the part have been created, the file needs to be post
processed. Post processing converts a part file (VNC file) which contains the machining
operations (toolpaths) into a text file (NC program) that can be transferred to the machine
control. A Post Processor specific to the machine control is used to convert the VNC file
into a text file. Communicating the posted text file to the CNC machine is discussed in the
Communications chapter which follows this one.
Communications Button
Clicking on the Process button will generate the NCprogram for the file currently open. The
text file will be saved under the file name displayed to the right of the Program Name button. If a file
with that name already exists, clicking the Process button will erase the old file and replace it with
the new one. To view the text file as it processes, click on the Text Window button. When this button
is depressed, a window will appear that displays the posted text file as it is created. The program will
scroll by in the window as it is being generated. The Pause button allows the user to stop the
scrolling of the output as it is being processed. The Print button will be available after the program
file is finished processing.
Before posted output can be generated, the program file name must be specified. When a file is
post processed, a text file is created with the extension specified in the Post text box in the File
Extensions dialog. By default this extension is set to .NCF. A file can be post processed multiple
times, and saved with different .NCF file names. If changes are made to the part file, it must be post
89
◆ L e v e l 0 T u r n i n g GFK-1701
processed again in order to incorporate the changes into the posted output. As a default, the text file
uses the part file name with an .NCF extension (e.g. EXAMPLE1.NCF). This file name can be
changed by clicking on the Program Name button and entering a new name.
To specify an output file name for the finished program, click on the Program Name button.
The system will automatically add the extension specified in the File Extensions dialog. Selecting
File Extensions from the Preferences submenu in the File menu will display the File Extensions
dialog shown below.
Starting Program Number : This is the number of the program as it will appear in the control. It is also
the starting number for all sub-programs. If the Starting Program Number is one, the first sub-
program will be two, the second three, etc.
Sequence from : This is the starting number for the block numbers or “N” numbers. The by box
determines the increment.
Minimize : If this option is turned on, the post processor will only output block numbers on tool
change positions.
Insert Comments : This option will output information about each operation and tool used as well as
file length. If any additional comments have been entered by the user about tools or operations, they
will be output as well.
Insert Optional Stops at Tool Change Positions : If this option is on, the software will output a machine
operator selectable program stop at every tool change.
90
GFK-1701 P o s t P r o c e s s i n g ◆
The dialog contains a number of yes/no buttons that provide various options for how comments
will appear in the final posted output. Turning on one of the buttons so that it contains a red dot will
cause the post processor to output that comment.
91
◆ L e v e l 0 T u r n i n g GFK-1701
CHAPTER 10 : C o m m u n i c a t i o n s
The system contains integrated communications. Third party communications packages,
including Gibbs ncCommunications, can also be used to communicate with CNC machines.
Before a file can be sent to the CNC machine, the parameters for a file transfer need to be set-
up. This is done in the Com Set-Up Dialog. It is accessed from the Preferences sub-menu of the File
menu. This dialog is used to set up communication protocols needed for sending a program (text file)
to a control or receiving a program from the control. Different controls have different protocols
(parameters). Refer to the machine control manual for the necessary protocol specifications.
PROTOCOLS
ADDING A PROTOCOL
A new protocol is added by typing in a new name and changing all of the settings to match
those of the CNC machine. Clicking on the Add button will add the protocol to the current database
of protocols.
After a protocol has been added, the name will appear in the upper left hand corner (as shown
above). Additional protocols can be entered and saved in the same manner. Saved protocols can be
accessed in the Protocol pop-up menu in the upper left hand corner of the dialog.
92
GFK-1701 C o m m u n i c a t i o n s ◆
CHANGING A PROTOCOL
To change information about a protocol, select the protocol from the list and change the
information. The changes are automatically saved when the dialog is closed or when a different
protocol in the list is selected.
REMOVING A PROTOCOL
To remove a protocol, simply select the desired protocol from the list and click on the Remove
button.
C O M M U N I C AT I N G W I T H A C N C M A C H I N E
To send a file to or receive a file from a CNC machine, click on the Communications button in
the Post Processor Dialog.
Communications Button
COMMUNICATIONS DIALOG
This brings up the Communications Dialog. The Communications Dialog can also be accessed
from the File menu. Files can either be sent to the machine control or received from the control. The
File Type radio buttons indicate what type of file will be sent. When a file is post processed, a text
file (NCF file) is created. NCF (text) is the necessary selection when sending posted NCF files from
the computer to the control or vice versa. The VNC (binary) selection allows users to send and
receive VNC files, which are the actual part files that contain the geometry and toolpaths. VNC files
can be communicated between computers that have the system installed. This is especially useful
when the system is built into the control of a machine tool. Part files (VNC files) can be
communicated in their entirety from a computer to the machine’s control, and from the control back
to the computer.
93
◆ L e v e l 0 T u r n i n g GFK-1701
NOTE:
It is recommended that edited .NCF files received back from the machine control be saved
under a different name than the original .NCF file that was initially sent to the control. That way if
the original .VNC file is reprocessed, it won't affect the edited .NCF file. For example, a part file
named SAMPLE.VNC is post processed and a text file named SAMPLE.NCF is created. Changes
are made to the program at the machine control and the new file containing those changes is sent
back and received at the offline computer, but under the name SAMPLE,NCF. If SAMPLE.VNC is
reprocessed again at a later date, it won't destroy the SAMPLE1.NCF file that contains the changes
that were made at the machine.
94
GFK-1701 T u t o r i a l ◆
CHAPTER 11 : T u t o r i a l
The easiest and most effective way to learn the system is by
actually programming a part, which is what we will do in this tutorial
section. A simple lathe part is created to teach the basic steps
involved with creating geometry, tools and machining operations.
These steps are outlined in detail so that you can program this part.
The blueprint for this part is found at the end of this section.
C R E AT I N G A N E W PA RT
• Click on the Document Control button in the Top Level palette.
95
◆ L e v e l 0 T u r n i n g GFK-1701
The stock size will be used to draw the stock outline and origin
marker on the screen. The system will also use the stock size
dimensions to calculate tool moves when the Auto Clearance and/or
Material Only options are used.
96
GFK-1701 T u t o r i a l ◆
The Auto Clearance value specifies an offset amount from the part
stock. The system uses this offset value to calculate clearance moves
between operations; where the tool can safely rapid between
operations without part interference. Because the stock conditions
are constantly changing as material is removed from the part, in order
to create more efficient toolpaths, an offset value is used for clearance
positioning rather than a static location (which is what is done if Auto
Clearance is turned off).
• Enter the values shown below for the Tool Change position.
The Tool Change position is the user selected datum for the tool
turret. If Tool Change is on, the turret will be sent to the specified
97
◆ L e v e l 0 T u r n i n g GFK-1701
• Close this dialog by either clicking on the Document Control button in the
Top Level palette or clicking in the Close box in the upper right corner of the
dialog.
You are looking at the top view of the part, the XZ plane. In order to
get a better visual picture of the part, we will change the view.
This will bring up the View Control palette, also referred to as the
Trackball, which allows you to change views, redraw, and unzoom.
98
GFK-1701 T u t o r i a l ◆
You can select the different options by clicking on the buttons. You
can also rotate the small part in the center to view the part from any
orientation. For an explanation of the various buttons and views, we
will turn on Balloon Help.
To have balloons come up on the screen, move the cursor over the
object that you want information on, as shown below.
This is a “world” view which allows you to see the round wire frame
of the stock. The Top View is recommended for creating geometry
and toolpaths, while the Isometric view is an excellent choice for
rendering and viewing the cut part.
99
◆ L e v e l 0 T u r n i n g GFK-1701
• Click on the View Control button again to put the trackball away.
All of the items on the trackball are also available in the View menu.
C R E AT I N G PA RT G E O M E T RY
Typically, the best way to create part geometry is to choose a starting
location and work in either a clockwise or counter-clockwise
direction around the part. In this particular example, we will begin
in the lower right hand corner, and proceed in a counter clockwise
direction. If you have not done the Geometry ry Exercise in the
Geometry Creation Chapter, it is suggested that you do that first
because it provides a more detailed description of the geometry
creation process.
100
GFK-1701 T u t o r i a l ◆
• Select the Chamfer feature type and enter the length value shown below.
Current
Row
Chamfers are not drawn on the screen until the preceding and
following features are fully connected. Therefore, this chamfer will
not be drawn until we close this shape at the end of the exercise.
Current
Row
• Enter the angle and the line point values shown below.
Current
Row
101
◆ L e v e l 0 T u r n i n g GFK-1701
• Select the Fillet feature type and enter the radius value shown below.
Enter the row.
Current
Row
Fillets are similar to chamfers in that they are not drawn on the screen
until the preceding and following features are fully connected.
• Enter the line point value shown below. Enter the row.
Current
Row
Current
Row
The radius value will default to the previous value entered for a fillet.
102
GFK-1701 T u t o r i a l ◆
• Enter the angle and the line point values shown below. Enter the row.
Current
Row
• Enter the line point value shown below. Enter the row.
Current
Row
Your screen should look like the picture shown below. Notice that
both fillets have been drawn because the preceding and following
features are fully connected.
• Enter the angle and line point values shown below. Enter the row.
Current
Row
Current
Row
103
◆ L e v e l 0 T u r n i n g GFK-1701
• Enter the angle and line point value shown below. Enter the row.
Current
Row
Current
Row
• Enter the angle and the line point values shown below. Enter the row.
Current
Row
• Enter the line point value shown below. Enter the row.
Current
Row
Now, we will create the geometry for the O-ring. Dimensions for the
O-ring groove are provided in the detail of the part print.
104
GFK-1701 T u t o r i a l ◆
• Enter the angle and the line point values shown below. Enter the row.
Current
Row
• Select the Fillet feature type and enter the radius value shown below.
Enter the row.
Current
Row
• Enter the angle and the line point value shown below. Enter the row.
Current
Row
Current
Row
• Enter the angle and the line point values shown below. Enter the row.
Current
Row
• Enter the line point value shown below. Enter the row.
Current
Row
105
◆ L e v e l 0 T u r n i n g GFK-1701
• Enter the line point value shown below. Enter the row.
Current
Row
• Enter the line point value shown below. Enter the row.
Current
Row
• Select the Fillet feature type and enter the radius value shown below.
Enter the row.
Current
Row
• Enter the angle and the line point values shown below. Enter the row.
Current
Row
106
GFK-1701 T u t o r i a l ◆
Current
Row
• Enter the end point values shown below. Enter the row.
Current
Row
This line must be defined with an endpoint because the next feature is
an arc that requires a start point. Anytime an arc is not tangent to the
previous line, the arc needs to have a start point. A start point is
created by defining an end point on the previous feature. Notice that
when a line is created with an endpoint, the line is trimmed and a
terminator point is created.
• Select the Clockwise Arc feature type and enter the radius value shown
below. Enter the row.
107
◆ L e v e l 0 T u r n i n g GFK-1701
Current
Row
Notice the prompt. It states that this row will create a circle that will
start at the last row’s endpoint.
Current
Row
Current
Row
The finished shape should look like the picture shown below. Notice
that the chamfer we created at the beginning has been drawn because
the lines it is between are now fully connected.
108
GFK-1701 T u t o r i a l ◆
C R E AT I N G A T O O L L I S T
In order to create machining operations, tools must be defined. The
system contains information for a variety of different types of inserts
and pre-defined insert specifications.
The dialog shown above is a Mill Tool Dialog. This dialog allows
you to make milling type tools, such as drills and bores, for turning
parts. You can change between the Mill Tool Dialog and the Lathe
Tool Dialog by clicking on the Tool Type button.
109
◆ L e v e l 0 T u r n i n g GFK-1701
• Click on the Lathe Tool Type button, if necessary to change to the Lathe
Tool Dialog.
110
GFK-1701 T u t o r i a l ◆
The picture shown below displays the desired insert angle and tool
holder.
The selection of insert and tool holder also affects the toolpaths
created using this tool. The system uses the selections made here
when constructing a toolpath to prevent tool interference. Therefore,
selections made here directly affect the machining of the part.
111
◆ L e v e l 0 T u r n i n g GFK-1701
This closes the Tool #1 dialog and brings up the Tool #2 dialog. You
can also close the dialog by clicking in the Close box in the upper left
corner. A Tool tile displaying the insert type and tip radius will
appear in position #1 of the Tool list.
112
GFK-1701 T u t o r i a l ◆
113
◆ L e v e l 0 T u r n i n g GFK-1701
The insert angle and holder type picture box should look like the
picture shown below. The correct selection is the last one in the
group.
114
GFK-1701 T u t o r i a l ◆
The Holder diagram and specs should look like the picture shown
below.
Because we are creating another Groove tool, you only need to enter
the new tool specifications.
115
◆ L e v e l 0 T u r n i n g GFK-1701
The insert angle and holder type picture box should look like the
picture shown below. The correct selection is the first choice.
• Click once on the scroll arrow at the bottom of the Tool list so that one
empty tile location becomes available.
116
GFK-1701 T u t o r i a l ◆
The scroll arrows at the top and bottom of tile lists allow you to easily
move through the tiles in the list. You can scroll the list a “page” at a
time by holding down the scroll button and moving the mouse in the
direction of the arrow. The arrow will turn red when scrolling a page
at a time. Refer to the Interface Chapter for more information on Tile
Lists.
Your Tool List should look like the picture shown below.
117
◆ L e v e l 0 T u r n i n g GFK-1701
Once the Style and TPI (threads per inch) values are selected, the
Insert Width and Insert Type will default to the desired values.
The insert angle and holder type picture box should look like the
picture below. The correct selection is the first choice.
• Close the tool dialog by clicking in the Close box in the upper right corner
of the dialog.
118
GFK-1701 T u t o r i a l ◆
The tools necessary to machine this part have now been created. In
order to review the tools contained in the list, we will use the Tool
List Summary option found under the Part Name menu.
The Tool List Summary dialog will appear on the screen. This dialog
can be resized by clicking in the size box in the lower right corner
and dragging it to the desired size. You can print the summary
information by selecting Print under the File menu and selecting the
Tool Summary option. When any of the summaries are displayed on
the screen, they can be printed.
C R E AT I N G O P E R AT I O N S U S I N G
THE PROCESS LIST
• Click on the Document Control button to bring the Document Control dialog
up on the screen.
119
◆ L e v e l 0 T u r n i n g GFK-1701
Operations
List
Process
List
Machining
Palette
Process tiles are created by dragging a Tool tile and a Function tile to
a Process list location. Operation tiles are created from Process tiles
when the Do it or Redo it button is depressed, and part geometry is
selected, if necessary.
First, we will create an operation that will face the front of the part.
• Select the Contouring Function tile and drag it to position #1 in the empty
Process list.
120
GFK-1701 T u t o r i a l ◆
• Select Tool tile #1 (80° C) and drag it to position #1 in the process list.
Drop it on top of the contouring tile already in position #1.
When you drop the Tool tile in position #1, the tool number, which is
one in this case, is displayed in the small box on the Contouring
Process tile. Also, the Contour Process dialog will come up when the
tool tile is added.
121
◆ L e v e l 0 T u r n i n g GFK-1701
To position the tool to cut the face of this part, we need the tool to
approach and retract along the Z axis. Therefore, the Front Face
option is selected. It is very important to move and position the tool
correctly. For more information on how the tool moves between
operations and properly positions to cut the part, refer to the
Clearance Moves section in the Machining Chapter.
For this process, the Material Only option is selected so the system
will not make the toolpath unnecessarily long to cut the face. The
122
GFK-1701 T u t o r i a l ◆
Material Only option provides for “no air cutting.” The stock size
and shape will be taken into account when this operation is created.
The Clearance value entered specifies an offset value from the part
geometry. The tool must make feed moves when it comes within that
distance of the part geometry.
• Close the Contour Process dialog by clicking in the small box in the upper
left-hand corner.
In this case, the start feature and end feature markers stay in their
initial positions because only one feature needs to be selected to cut
the face of the part. The start point and end point markers will be
dragged to different positions. The start and end point markers can be
placed anywhere on the selected line; even on a portion of the line
that has been trimmed away. Refer to the Machining Markers section
for more information.
123
◆ L e v e l 0 T u r n i n g GFK-1701
• Drag the start point (white circle) marker up to the location shown.
Because the Material Only option is selected in this process, the start
and end point markers do not need to be placed in exact positions, as
long as they clear the material. The system will create the most
optimal toolpath for cutting the face.
• Drag the end point (black circle) marker down to the location shown. Try
and make it close to the origin.
With the process dialog complete and the cut shape defined, we will
create the operation that will actually cut the face of the part.
124
GFK-1701 T u t o r i a l ◆
In addition, the approach and retract moves and the toolpath will be
drawn on the screen. The orange lines represent the toolpath, while
the gray lines represent positioning moves. The solid lines for both
the toolpath and positioning indicate feed moves. And the dashed
lines of both colors indicate rapid moves.
The picture shown above on the right shows the toolpath without the
machining markers so you can get a better picture. To view the
toolpath without the machining markers, simply click anywhere off
the part. The angled dashed gray line shows the tool rapiding from
the tool change position, entered in the Document Control dialog, to
the start point of the toolpath.
You’ll notice that there are angled lines at the beginning and end of
the toolpath. These are entry and exit positioning moves that have
been added because Auto Clearance is turned on. They are angled
along the centerline of the insert angle. The position the tool can
125
◆ L e v e l 0 T u r n i n g GFK-1701
or
When Operations have been satisfactorily completed,
before proceeding, it is VERY IMPORTANT that all
Operations are deselected. By deselecting the
completed operations, they become fixed in the
Operations list, and will not be affected by changes
made to the Process list. Operations can be edited, but
to do so they must be reselected.
• Click on the Contouring Process tile in position #1 in the process list and
drag it to the wastecan.
When creating a new process list, you can either throw away the old
tiles in the list or modify them in order to create the new operations.
In this case we will throw away the old tile and start from scratch.
Just keep in mind that every tile in the process list will be used to
create operations when the Do it button is depressed.
The next group of operations we will create will rough and finish the
outside contour of the part. This will be accomplished using Multiple
Process Programming which allows multiple process tiles to be
applied to one cut shape. This provides for a highly efficient method
of programming parts.
126
GFK-1701 T u t o r i a l ◆
• Select the Roughing function tile and drag it to position #1 in the empty
process list.
127
◆ L e v e l 0 T u r n i n g GFK-1701
Lathes use different roughing (multiple cut) cycles. There are three
general types: Turn, Plunge, and Pattern Shift. The posted output
generated by the system will produce every move necessary to rough
the part.
Turn roughing cycles are the standard contour rough cycle. For
turning cycles, the selection made for the approach type (OD, ID,
Front Face) determines what type of contour rough style will be
generated by the system.
For this process, the Cut Depth value entered is 0.1. The Xr label
indicates that it is a radius value. This means that 0.1" of material
will be removed from each side on each pass.
128
GFK-1701 T u t o r i a l ◆
The Shape Axes radio buttons allow the user to regulate the axes and
directions of the cut shape. Omitting an axis (such as X-) will
prevent cut shape moves in the disallowed direction. If a particular
Cut Axis is deselected no red dot will appear beside that axis. Refer
to the Machining Chapter for more information on cut shapes and the
Shape Axes buttons.
For this process, the X axis in the negative direction is turned off.
This means that the cut shape is defined so it will not cut in the X-
direction.
The value entered in the Fin. Stock ± text box designates the
minimum amount of material that will be left outside of the part
geometry after the roughing cycle is completed. The toolpath created
by the system will be offset from the part geometry by 0.1". We
will remove this excess with the finish pass.
• Select the Roughing function tile and drag it to position #2 in the process
list.
129
◆ L e v e l 0 T u r n i n g GFK-1701
• Select tool tile #3 and drop it on top of the roughing tile in position #2.
This process is included in this group to rough the neck groove on the
part. Again, an OD approach type is selected so the tool will
approach and retract along the X axis. And a Turn rough cycle is
selected with a cut depth of 0.75".
The Cut Direction selection indicates the direction the tool will move
along the designated cut shape.
130
GFK-1701 T u t o r i a l ◆
Material Only is again selected for the Rough Style so that the
toolpath generated for this operation will only cut the remaining
material left on the part after the previous operations have been
completed. The Material Only selection is particularly useful when
utilizing the Multiple Process Programming capabilities of the
system. Feed moves will only be made where it is necessary to
remove material. The tool will make rapid moves whenever possible
while maintaining the clearance offset.
• Select the Contouring function tile and drag it to position #3 in the process
list.
131
◆ L e v e l 0 T u r n i n g GFK-1701
• Select tool tile #3 and drop it on top of the contouring tile in position #3.
To properly position the tool to finish the OD, we need the tool to
approach and retract along the X axis. Therefore, OD is selected for
the approach type.
Entry and exit moves can be user defined and entered for each
process. If entry and exit lines and/or radii are defined in the
process dialog, they will automatically be added to the toolpath. The
Auto Clearance option may create additional entry and exit moves, if
need be, to maintain the necessary clearances, but the entry and exit
moves designated in the process dialog will always be included in the
toolpath.
132
GFK-1701 T u t o r i a l ◆
Similarly, an exit radius and line will be created at the end of the
toolpath. The 90° arc will be tangent to the last feature of the
toolpath, and the line will be perpendicular to the arc.
Now that the process list is complete, we will define the cut shape.
133
◆ L e v e l 0 T u r n i n g GFK-1701
The start and end point markers do not need to be placed in exact
locations, as long as they clear the material.
• Drag the end feature marker (black square) and drop it on the part
geometry as shown.
The end point marker will automatically move with the end feature
marker.
As you move the machining markers, notice that the cut shape,
represented by the dark blue line, will adjust according to the position
of the markers.
Your screen should look like the picture shown on the following
page. The dark blue cut shape is the part of the contour that will be
machined using these processes. Notice that the middle V groove and
the O-ring groove are not included in this cut shape. The machining
markers, in this case the end feature and end point markers, allow us
to specifically designate what portion of the geometry is to be
machined by the processes we have created.
134
GFK-1701 T u t o r i a l ◆
Your Operations list should look like the picture shown below.
The positioning moves and toolpaths for each of the operations are
also drawn on the screen. In order to get a better picture of the
toolpaths generated by the system, we will view the tool moves for
the first roughing operation separately.
or
135
◆ L e v e l 0 T u r n i n g GFK-1701
Clicking once on a tile will select and highlight the tile without
opening any dialogs or selecting other tiles that were created with it.
Only the toolpath and positioning moves for the selected operation
will be drawn on the screen. This is helpful if you use multiple
process programming and wish to view individual toolpaths.
Your screen should look like the picture shown below.
Notice that the custom stock outline was taken into account because
Auto Clearance is on and the Material Only option was selected.
Also, the toolpath created does not slope at all into the neck groove
because the X- Cut Axis was deselected in the Rough process dialog
that created this operation.
The dashed gray lines show the tool rapiding from the end point of
the previous operation to the start point of this operation, and to the
tool change position at the end of the operation.
Now that operations have been created, we will render the part.
There are several ways to verify that the toolpaths generated by the
system will safely and correctly cut the part. Looking at the
toolpaths, as we have done thus far, is one way. Another way is to
render the part which allows you to actually view the tool removing
material and cutting the part.
136
GFK-1701 T u t o r i a l ◆
• Select the Isometric view by clicking on the Isometric button in the View
Control palette or selecting the Isometric item in the View menu.
• Click on the Cut Part Rendering button in the top level palette.
When the Cut Part Rendering button is depressed, the part will no
longer appear as a wire diagram, but instead will be displayed as a
3-D solid model, as shown below.
The Cut Part Rendering palette, shown below, also appears on the
screen.
137
◆ L e v e l 0 T u r n i n g GFK-1701
A part can be rendered at any time once operations have been created.
The stock will always be shown in shades of blue. Selected
operations will render in shades of yellow, while all other operations
will render in shades of gray. Red will be displayed when non-
cutting tool surfaces or rapid moves hit the material. Refer to the Cut
Part Rendering Chapter for more information.
• Click on the Cut Part Rendering button in the Top Level palette again to
return to the wire frame view of the part.
• Change back to the top view of the part by either clicking on the Top View
button in the View Control palette, or selecting Top View from the View
menu.
or
138
GFK-1701 T u t o r i a l ◆
• With the shift key depressed, click on the three tiles in the Process list and
drag them to the wastecan.
Next we will create the operations that will rough and finish the V
groove and the O-ring groove on the OD.
• Select the Roughing function tile and drag it to position #1 in the empty
process list.
139
◆ L e v e l 0 T u r n i n g GFK-1701
When the Plunge option is selected for the Rough Type, the Plunge
dialog will come up on the screen. To make the Plunge dialog come
up, click on the Plunge option in the Rough Type selections.
140
GFK-1701 T u t o r i a l ◆
The Plunge Angle specifies the angle at which the groove tool will
make its plunging moves. The default is 270° which has the tool
plunging straight down.
For this process, we have selected the Details option for the cut width
This option will vary the cut width distance as necessary in order to
hit the endpoints of each feature of the cut shape. The Z value
entered specifies the maximum distance the tool will step over on
each pass. The Center Out Cuts option is selected so that the tool
will make its first plunging move in the center of the groove, and then
proceed to rough each side.
141
◆ L e v e l 0 T u r n i n g GFK-1701
For this groove, the Peck Full Out option is selected because the
groove is relatively deep, and in order to remove all of the chips
(material), the tool will need to come all the way out of the part after
the peck. The value entered in the Peck text box specifies the
distance the tool will plunge into the part on each peck. The
Clearance value specifies the distance away from the remaining
material the next peck will begin.
• Select the Contouring function tile and drag it to position #2 in the empty
process list.
142
GFK-1701 T u t o r i a l ◆
• Select the Roughing function tile and drag it to position #3 in the process
list.
143
◆ L e v e l 0 T u r n i n g GFK-1701
144
GFK-1701 T u t o r i a l ◆
The Constant option is selected for the Cut Width. The tool will step
over a distance of 0.2" on each pass regardless of the endpoints of the
cut shape. The Peck Retract operation is selected for the First
Plunge. The Peck amount specifies the depth of each plunge and the
Retract amount specifies the distance the tool will come out of the
hole after each peck.
• Select the Contouring function tile and drag it to position #4 in the empty
process list.
145
◆ L e v e l 0 T u r n i n g GFK-1701
Now we will define the cut shape for this process list.
146
GFK-1701 T u t o r i a l ◆
Make sure you select the outside circle and the arrow pointing left.
The blue cut shape drawn should include the V groove and O-ring.
The toolpaths that are created will properly rough and finish both the
V groove and the O-ring. Notice that the toolpath contains no
unnecessary moves. The Material Only option allows us to take full
advantage of multiple process programming without making
unnecessary tool moves.
147
◆ L e v e l 0 T u r n i n g GFK-1701
The Cut Part Rendered image should look like picture shown below.
• Click on the Cut Part Rendering button in the Top Level Palette again to
return to the wire frame view of the part.
• Change back to the top view of the part by either clicking on the Top View
button in the View Control palette, or selecting Top from the View menu.
• With the shift key depressed, click on the four tiles in the Process list and
drag them to the wastecan.
There are shortcuts for selecting a group of tiles in any tile list. Refer
to the Shortcuts Appendix or the Shortcuts information card for
details.
148
GFK-1701 T u t o r i a l ◆
Except for the thread, the OD of our part is complete. Now, we will
create the operations to drill a hole through the center of the part and
rough and finish the ID.
• Select the Drilling function tile and drag it to position #1 in the empty
process list.
149
◆ L e v e l 0 T u r n i n g GFK-1701
Full
Sharp Tip Z Diameter Z
The depth the drill will feed to is specified by the value entered in the
Sharp Tip Z text box. Values may be entered in the text boxes
specifying the Full Diameter Z depth and the Spot Diameter. These
values will cause the Sharp Tip Z to be recalculated. The Sharp Tip
Z is the value used in the posted output.
The drill cannot feed through the part in one pass. Therefore, the
Peck, Full Out option is selected. Because it is a Peck, Full Out, the
drill will rapid all the way out of the part after each peck.
150
GFK-1701 T u t o r i a l ◆
The value entered in the Peck text box specifies the amount the tool
will peck into the material on each pass. The next peck will start a
Clearance amount away from the material remaining after the
previous peck.
• Select the Roughing function tile and drag it to position #2 in the process
list.
151
◆ L e v e l 0 T u r n i n g GFK-1701
For this process, the Full option is selected for the Rough Style. The
Full option gives the user more control over how the toolpath will be
created. Not only does the user enter the stock start position, but the
152
GFK-1701 T u t o r i a l ◆
start and end points of the toolpath will be determined from the
placement of the start and end point machining markers. The Rapid
Step option is available for roughing operations that use the Full
option for the Rough Style. Rapid Step is selected so that the tool
will make a rapid move (if not selected, a feed move) from the cycle
start point to the start point of each cut.
• Select the Contouring function tile and drag it to position #3 in the Process
List.
153
◆ L e v e l 0 T u r n i n g GFK-1701
Make sure that you select Front ID for the Approach Type so that the
tool approaches and retracts from the part correctly.
154
GFK-1701 T u t o r i a l ◆
The dashed orange line at X = 0 shows the tool rapiding out of the
part after it has pecked in to the Sharp Tip Z depth.
The rendered image should look like the picture shown below.
155
◆ L e v e l 0 T u r n i n g GFK-1701
• Click on the render button in the top level palette again to return to the
wire frame view of the part.
• Select the tiles in the Process list and throw them away.
Next, we will create the operation that will cut the required thread.
• Select the Threading Function tile and drag it to location #1 in the empty
Process list.
• Click on the scroll arrow at the bottom of the Tool list to make tool #7 and
tool #8 available for selection.
156
GFK-1701 T u t o r i a l ◆
The Actual Thread Start and Thread End are values that can be taken
directly from the blueprint. The Z Run In distance is used if the
threading tool needs to begin a certain distance away from the actual
thread start to accelerate to the proper feed rate. The X Run In
distance can be used if you wish to come in and start the thread at an
angle. The Run Out distances are used in the same manner.
The bottom two boxes specify the Actual Thread Start and Actual
Thread End. These values are taken directly from the part blueprint.
These values represent an “ideal” thread and are values that can be
taken directly from the part blueprint.
157
◆ L e v e l 0 T u r n i n g GFK-1701
The Last Cut option is selected to prevent any cut from removing less
than 0.01" from each side. This is also the cut depth that the
threading tool will remove on the last pass.
158
GFK-1701 T u t o r i a l ◆
As the last step we will use the Sort Ops function to put the
operations in the list into a more optimal machining order. Sort Ops
will reorganize the operations by tool number and creation order.
The only change that occurs is the drilling operation that uses tool #2
will be moved up in the Operations list to location #3.
159
◆ L e v e l 0 T u r n i n g GFK-1701
The final rendered image should look like the picture shown below.
In this case, changing the order of the operations does not cause any
tool interference and does not appear to affect the efficiency of the
toolpath and positioning moves generated by the system. Had there
been any problems, we would need to reprocess the existing
operations so that the system would recalculate the tool moves for
each operation based on the new conditions.
All operations required to machine the tutorial part have now been
created. Post Processing will create a text file that will be used by the
machine to cut the part. Refer to Post Processing Chapter for
additional information on post processing.
160
PA RT B L U E P R I N T
GFK-1701
4.900
4.150
4.000
5° Typ.
3.800
2.500
2.200
.015R .975
2.250-8 Thread
.800
45¡
1.600 1.100
2.520
2.800 2.600 1.400 1.600 2.250
1.000
.200R 7 Places
45¡
63¡
45° x .200
48¡
T u t o r i a l
161
◆
◆ L e v e l 0 T u r n i n g GFK-1701
APPENDIX 1 : O p e r a t i n g S y s t e m s
LAUNCHING THE SYSTEM
The method for starting up Virtual Gibbs Mill is different depending on the operating system.
DOS
1. Change the current directory to the Virtual directory and type in “VIRTUAL”.
2. Create a batch file that automatically accomplishes #1.
3. Launch VIRTUAL.EXE from an MS-DOS file manager.
The DOS version cannot be run from within an MS-DOS shell under Windows or OS/2.
MACINTOSH
1. Double-click on the Virtual Gibbs vXX.XX icon.
2. Double-click on an icon for a Virtual Gibbs document.*
3. Drag a Virtual Gibbs Mill document icon on top of the Virtual Gibbs vXX.XX icon.*
*These methods will launch Virtual Gibbs Mill and automatically open the document.
WINDOWS NT
1. Double-click on the Virtual Gibbs vXX.XX icon.
2. Change the current directory to the Virtual directory and type in “VIRTUAL”.
3. Double-click the VIRTUAL.EXE file from the file manager.
4. Use a third party launching utility.
The Associate function in the file manager will not work.
WINDOWS 95
1. Double-click on the Virtual Gibbs vXX.XX icon.
O P E R AT I N G S Y S T E M S G L O S S A RY
The MS-DOS®, Windows NT®, Windows 95® and MacOS® operating systems use different
terminology for certain common items. A short list has been provided to help eliminate possible
confusion.
EQUIVALENT TERMS
file = document
program = application
directory = folder
backspace key (not delete or del) = delete key (not del)
162
GFK-1701 O p e r a t i n g S y s t e m s ◆
F I L E C O M PAT I B I L I T Y
Part files can be moved back and forth between Macintosh, DOS, Windows NT and Windows
95 systems. The Preview function (in the Open dialog) provides information regarding the status of
the selected file. An old format data file will say "Preview not compatible" in the picture window.
There may also be descriptive text at the bottom near the comment and stock dimensions. Updating
requires that the document be opened and saved in its native format (the platform it was created on.)
Once updated, Macintosh data files may be moved to a DOS/Windows systems, and vice-versa.
When previewing a DOS/Windows file on a Macintosh, the background of the preview picture is
white (as opposed to the normal black). Once Opened and Saved, it will look like all other Macintosh
files. The same is true on the DOS/Windows side, when dealing with Mac files.
The actual moving of files between Macintosh and DOS/Windows computers can be
accomplished using one of several programs available. These include PC Exchange from Apple,
Apple File Exchange, Access PC, and DOS Mounter. Refer to the documentation for these products
for instructions on how to facilitate the transfer. However, regardless of which package is used, be
sure to do the following things:
When transferring a Macintosh file to a DOS computer, make sure the file name is no
OS more that 8 characters in length (before the extension) and add .VNC to the end of the
file name. (i.e. VIRTTEST.VNC). When transferring a DOS/Windows file to a
Macintosh computer, change the file type to .vnc and the creator to CATL.
PC Exchange® from Apple is strongly recommended for any Macintosh being used to
exchange part files with a DOS machine. It automates the floppy transfer process nicely.
S TA N D A R D F I L E E X T E N S I O N S
There are several different files that the system uses/creates.
* This is the default extension. It can be changed by selecting File Extensions from the Preferences
sub-menu under the File menu.
163
◆ L e v e l 0 T u r n i n g GFK-1701
APPENDIX 2 : P r i n t i n g
PRINTING PREFERENCES
Geometry, toolpaths and rendered images can all be printed by selecting the Drawing item in
the Print submenu. The Printing preferences allow the user to specify how the system will handle the
background color and the colors of the image.The system supports printing in color on all operating
systems. Selecting the Printing item from the Preferences submenu will display the Printing
Preferences Dialog, shown below.
Options are available for printing geometry and toolpaths and the rendered image. Selecting
Screen will print the drawing exactly as it appears on the screen, with a black background and the
colors as they appear on the screen. Selecting Screen on White will print the image in color, but on a
white background. Selecting Black on White for Geometry & Toolpath will convert all the colored
items to black and print them on a white background. If the printer being used is a black and white
printer, the Black on White option should be selected to ensure that all portions of geometry,
including those that are a light color, can be seen on the print.
DOS SYSTEMS
On DOS Systems, the Printing Preferences Dialog allows the user to select a printer, the printer
port and the image orientation. The dialog contains a pop-up menu which contains over 100 printers
that are directly supported by the system. A complete list of supported printers can be found in the
Getting Started literature shipped with the software. The dialog also contains radio buttons which
allow users to select the printer port they wish to use, either LPT1 or LPT2, and the image
orientation, either portrait or landscape.
Once the appropriate printer has been selected, items can be selected from the Print submenu to
be printed.
164
GFK-1701 P r i n t i n g ◆
MACINTOSH SYSTEMS
Macintosh users select the printer from the Chooser dialog which is accessed from the Apple
menu. When an item is selected from the Print submenu, a print dialog specific to the selected printer
will be displayed on the screen.
Macintosh users have additional control over the finished image. Page Set-Up in the File menu
allows Macintosh users to change the scale and orientation of the finished image. The specifics vary
depending on the type of printer being used.
165
◆ L e v e l 0 T u r n i n g GFK-1701
APPENDIX 3 : M e n u s
FILE MENU
New: Selecting this item will create a new file by opening a dialog and
asking for a file name and a location to save the new file. If there is a file
open, it will be closed.
Open: Selecting this item will bring up the Open Dialog, which allows the
user to select which file to open. If a file is currently open, it will be
closed and the selected file will be opened.
Close: Selecting this item will close the current file. If the file has not been
saved before selecting Close, a dialog will come up asking if the file
should be saved.
Close Window: Selecting this item will put away the current, active window
on the screen.
Save: If there have been any changes made while the file was open, this
button will save the changes.
Save As: This item will open a dialog asking for a file name and location
to save the current file. The changes made since the last Save command
will be written into the new file. The original file will not be affected. The
new file will become the current, open file.
Save a Copy: This item is very similar to the the Save As button. The system will create a duplicate
copy of the open file. The name of the duplicate file can be changed from the default file name which
varies depending on the operating system. The original file remains the current, open file.
On DOS systems, if the original file name is less than 8 characters, the system will add
OS underscores to make the duplicate file's name 8 characters in length. If the original file's
name is 8 characters, the system will change the last character to an underscore to
distinguish the original file and the copy. On Macintosh, Windows NT and Windows 95 systems, the
word “copy”will be added at the end of the file name to distinguish it from the original.
166
GFK-1701 M e n u s ◆
NOTE: The Accuracy, Cutter Comp and Set Font Directory preferences are only available with the
Level 1 version of the software.
File Extension Preference: These preferences set the extensions that will
be added to different types of files that are created by the system.
The Post extension is added to the text file generated by the system
when a part file is post processed. The default extension is .NCF.
Communications: Selecting this item brings up the Communications Dialog which allows the user to
send and receive text files to and from the machine control. The Communications Dialog can also be
accessed from the Post Processing Dialog.
167
◆ L e v e l 0 T u r n i n g GFK-1701
Page Setup: This item is only available on Macintosh and Power Macintosh operating systems. The
Page Setup item gives the user additional control over the printed image, such as scale and
orientation. The specifics vary depending on the type of printer being used.
Quit: Selecting this item will quit the program. If the file has been modified since the last time it was
saved, a dialog will come up asking if the file should be saved.
NOTE: The Save Special, Materials, Import and Export items are only available in the Level 1 version
of this software.
EDIT MENU
Undo: This item will undo the last action performed. Some actions
cannot be undone. When Undo is grayed out in the menu, the previous
action cannot be undone.
Cut: This function will delete any selected items, and copy these items to
the clipboard. The item(s) can then be placed in the same file using the
Paste function.
Copy: This function will make a duplicate of the selected items and copy
it to the clipboard. The item(s) can then be pasted in the same file.
Paste: This function will place the contents of the clipboard in either the
drawing window, if the clipboard contains geometry, or an active text
box, if the clipboard contains text. If another item is selected when
pasting, that item will be deleted and replaced by the contents of the
clipboard.
Select All: This function will select all of the geometry contained in the current workgroup.
Deselect All: This item will deselect all geometry currently selected
168
GFK-1701 M e n u s ◆
Insert Row: This item is only active when the Geometry Expert spread sheet is open. When selected,
it will insert a blank row in the spreadsheet above the current row selected. When an inserted row
contains the necessary information and is entered, the system will recalculate the shape and attempt
to incorporate the inserted feature into the existing shape, if possible.
Delete Row: This item is only active when the Geometry Expert spread sheet is open. It will delete the
selected row from the spreadsheet. As soon as the row is deleted, the system will adjust the
remaining shape to maintain the appropriate connections, if possible.
Use Intersection #1 (#2): This item is only active when the Geometry Expert spread sheet is open. It
will toggle between Use Intersection #1 and Use Intersection #2 in the menu. This option enables the
user to select different intersections between concurrent features in the spreadsheet. This option is
available when the feature defined by the current row intersects the feature defined by the following
row in two places. This item will change the point of intersection, selected in a previous post
targeting dialog, to the other possible choice.
Reverse All Rows: This item is only active when the Geometry Expert spread sheet is open. When
selected it will reverse the order of the rows in the spread sheet which will change the direction of the
shape as it is loaded in Geometry Expert.
NOTE: The Select, Deselect and Redo All Ops items are only available with the Level 1 version of this
software.
169
◆ L e v e l 0 T u r n i n g GFK-1701
VIEW MENU
Top View: This is the standard, default view of the XZ plane.
Isometric View: This is a “world” view. The part is drawn such that the
part dimensions are all foreshortened equally.
Unzoom: Also known as no zoom. This sets the scale of the view to the
maximum size that the monitor will allow. It is based on the stock size
and the current view.
Redraw: This item refreshes the screen image allowing the user to get a
better indication of what is currently drawn on the screen. Geometry,
toolpaths, or the rendered part image can be redrawn using this item.
Previous View: This item changes the current view to the last view that
was worked in.
Zoom In: This item increases the scale of the view so the drawing gets
bigger by 25% each time it is selected.
Zoom Out: This item decreases the scale of the view so the drawing gets smaller by 25% each time it
is selected.
Labels: If this item is turned on, labels will be drawn next to every geometry feature drawn. Circles
will be labeled C#, Lines L#, and Points P#. The # is determined by the order the points and features
were created. It corresponds directly to the information shown in the Workgroup Summary.
Draw Points: If this item is turned off (not checked), all points will not be drawn. The default selection
has the Draw Points item turned on.
Extend Lines: When this item is turned on, all unconnected lines will extend to the edge of the stock. If
it is turned off, lines will only extend to the features they were created between.
Show Stock & Origin: The default has this item turned on. If it is turned off, the gray outline of the
stock and the origin marker will not be drawn on the screen.
Show Geometry: This item redraws only points, lines and circles. It will draw geometry over the cut
part rendered image of the part.
170
GFK-1701 M e n u s ◆
Shrink Wrap: When this item is selected, the software will examine the geometry in all of the
workgroups and adjust the stock size to show all the geometry on the screen without excess blank
space.
NOTE: The Home, Show CS Grid, Show Selected WG and Hide Selected WG items are only available
with the Level 1 version of this software.
MODIFY MENU
Duplicate: Selecting this item will copy the selected geometry, in the
same location. After this is done, the next appropriate step is to move
the duplicated geometry to another location, possibly using another item
under this menu. Additionally, Duplicate is useful for making an
unconnected feature in the same location as a currently connected
feature.
Duplicate And: This item will perform the individual functions Duplicate
and then Force Depth, Mirror, 2D Rotate, Scale or Translate at one
time. First, the selected geometry will be duplicated. Then, depending
on the option selected, the selected geometry is moved to one or more
new locations based on the number typed in the times text box. The
specific button choices work the same as the items detailed below. If the
selected geometry is an open shape and the modify selection matches
the terminators, the terminators will be changed to connectors as the
geometry is duplicated on the screen.
Set Default: Selecting a point and then choosing Set Default will cause the selected points X, Y and Z
locations to appear as the default values in any other appropriate Modify menu dialog. This item is
useful if a drawn point is used to mirror around, rotate around, etc.
Mirror: Selecting this item will move the selected geometry to the other side of the axis or axes
specified, around an axis point entered in the text boxes. Clicking on the Process button will perform
the mirroring function.
2D Rotate: Selecting this item will revolve or rotate the selected geometry around the point specified
in the Z and X text boxes. The selected feature will be rotated by the amount specified in the Angle
text box, in either a CW (clockwise) or CCW (counter-clockwise) direction depending on the
selection made. Clicking on the Process button will perform the rotating function.
Scale: Selecting this item will change the size of the selected geometry by the amount specified. The
value typed in the Amount box is a ratio of 1, 1 being full size. The inches to mm or mm to inches
buttons will change the geometry to the opposite numerical type. The Mill module has an Include Z
option. If the Include Z option is turned on, the Z values of the selected geometry will be included in
the scaling process. Include Z will not have an affect if the selected geometry is at Z0. Clicking on
171
◆ L e v e l 0 T u r n i n g GFK-1701
Translate: Selecting this item will move the selected geometry, by the specified amount along the
selected axis or axes. Clicking on the Process button will perform the translating function. This
dialog can remain on the screen for further use while other functions are performed.
Move Part Origin: Selecting this item will move ALL the geometry, in EVERY workgroup,
incrementally by the values typed in the appropriate axis text box. In other words, the current
location of X0, Y0, Z0 will change incrementally by the values in this dialog and a new X0, Y0, Z0
will be established. Clicking on the Process button will move the origin. This dialog can remain on
the screen for further use while other functions are performed.
Operation Data: When an Operation Tile is highlighted and this item is selected, the Operations Data
Dialog will come up on the screen. All machining specifications for the selected operation will be
listed in the Operation Data Dialog. A comment and utility data can also be entered in this dialog.
NOTE: The Force Depth, Sort, Change CS XYZ and Change CS HVD items are only available with the
Level 1 version of this software.
HELP MENU
Balloons: This item will turn on the computer aided training built into the
system. When this item is checked, balloons containing reference information
will come up on the screen whenever the cursor is placed over an object.
Prompting: When this item is checked, the Geometry Creation Palette and the Machining Palette are
extended to provide useful suggestions on how to proceed with creating geometry and toolpaths.
PA RT F I L E M E N U
Workgroup Summary: Selecting this item will display the Workgroup
Summary for the file which provides information on all geometry
contained in the current workgroup. When the Workgroup Summary
is open on the screen, it can be printed by selecting the Workgroup
Summary item from the Print submenu under the File menu.
Tool List Summary: Selecting this item will display the Tool List Summary for the file which provides
information on all tools. When the Tool List Summary is open on the screen, it can be printed by
selecting the Tool List Summary item from the Print submenu under the File menu.
Operation Summary: Selecting this item will display the Operation Summary for the file which
provides information about each of the machining operations contained in the file. When the
Operation Summary is open on the screen, it can be printed by selecting the Operation Summary
item from the Print submenu under the File menu.
172
GFK-1701 S h o r t c u t s ◆
APPENDIX 4 : S h o r t c u t s
The information contained in this section is also provided on the laminated Shortcuts card
provided with the software. The system contains several helpful commands and shortcuts that allow
users to quickly perform certain tasks and functions within the software. The specifics for using the
shortcuts vary depending on the operating system.
MENU ITEMS
File Menu View Menu
Ctrl N...............New File Ctrl E ...............Top View
Ctrl O...............Open File Ctrl F ...............Front View
Ctrl W..............Close Window Ctrl G...............Right View
Ctrl S ...............Save Ctrl I ................Isometric View
Ctrl P. ..............Print Drawing Ctrl H...............Home View
Ctrl Q...............Quit Ctrl U...............Unzoom
Edit Menu Ctrl R...............Redraw
Ctrl Z ...............Undo Ctrl + ...............Zoom In
Ctrl X...............Cut Ctrl - ................Zoom Out
Ctrl C...............Copy Ctrl L ...............Labels
Ctrl V...............Paste Ctrl J ................Draw Points
Ctrl A...............Select All Ctrl [ ................Show Geometry
Alt I .................Insert Row Ctrl ` ................Shrink Wrap
Alt K................Delete Row Modify Menu
Alt A................Use Intersection #1/#2 Ctrl D...............Duplicate
Palettes Menu* Ctrl Y...............Set Default
F1 ....................Document Control Help Menu
F2 ....................Geometry Creation Ctrl B...............Balloons
F3 ....................Tools
F4 ....................Machining
F5 ....................Views
F6 ....................Cut Part Rendering
F7 ....................Post Processing
* No longer in the menu bar, but the shortcuts still work.
173
◆ L e v e l 0 T u r n i n g GFK-1701
GEOMETRY EXPERT
Arrow Keys: Move through cells in the spreadsheet. Move down to the next row when editing existing
rows.
Tab Key: Move through cells in one row.
Alt + Click Geometry: Enter feature dimensions in cells of the spreadsheet. Hold down the Alt Key and
select a point or feature. The appropriate dimension for the selected feature will be entered in the
active cell of the spreadsheet.
Alt I: Insert new row into spreadsheet above the selected row.
Alt K: Delete selected row from the spreadsheet.
Alt A: Toggle between the possible intersections between features available when post targeting.
Alt 1: Line Feature Type
Alt 2: Chamfer Feature Type
Alt 3: Fillet Feature Type
Alt 4: Clockwise Arc Feature Type
Alt 5: Counter-Clockwise Feature Type
Alt 6: Close Shape
GEOMETRY SELECTION
Shift+ Click Geometry: Select multiple features or points.
Alt + Drag Rectangle: Select all geometry within the area created by dragging the rectangle.
MACHINING MARKERS
Alt + Click Feature: End Feature and End Point Machining Markers move to the position that is
clicked. The Markers do not need to be dragged.
TILE LISTS
Ctrl + Click Tiles: Select a group of contiguous tiles by selecting the first tile, and then clicking on the
last tile in the group while holding down the Alt key. All tiles in between become selected.
Shift + Click Tiles: Select multiple, non-contiguous tiles.
Shift + Double Click Empty Tile Location: Move all lower tiles up one in tile list.
Shift + Double Click Insertion Point: Create an empty tile location.
Click + Drag Scroll Arrow: Scroll through tile lists a page at a time. Hold down scroll arrow and drag
cursor in the direction of the arrow. The arrow turns red when scrolling the list a page at a time.
174
GFK-1701 S h o r t c u t s ◆
ALTERNATE SHORTCUTS
The DOS, Windows NT and Windows 95 versions of the software offer the user an alternate
option for which modifier key will be used for keyboard shortcuts. This feature is primarily geared
at customers who work in a multi-platform environment and have grown accustomed to using the
software on Macintosh systems. (Also, perhaps for those customers who suffer from limited finger
dexterity). The Shortcut options are set by selecting the Interface item in the Preferences sub-menu
under the File menu. The “Alternate Shortcuts” option emulates the Macintosh version of the
software, in that the modifier keys are positionally located in the same place on the keyboard as
they are on Macintosh keyboards.
MENU ITEMS
File Menu View Menu
Alt N................New File Alt E ................Top View
Alt O................Open File Alt F ................Front View
Alt W...............Close Window Alt G................Right View
Alt S ................Save Alt I .................Isometric View
Alt P. ...............Print Drawing Alt H................Home View
Alt Q................Quit Alt U................Unzoom
Edit Menu Alt R ................Redraw
Alt Z ................Undo Alt + ................Zoom In
Alt X................Cut Alt - .................Zoom Out
Alt C ................Copy Alt L ................Labels
Alt V................Paste Alt J .................Draw Points
Alt A................Select All Alt [ .................Show Geometry
Ctrl I ................Insert Row Alt ` .................Shrink Wrap
Ctrl K...............Delete Row Modify Menu
Ctrl A...............Use Intersection #1/#2 Alt D................Duplicate
Palettes Menu* Alt Y................Set Default
Alt 1.................Document Control Help Menu
Alt 2.................Geometry Creation Alt B ................Balloons
Alt 3.................Tools
Alt 4.................Machining
Alt 5.................Views
Alt 6.................Cut Part Rendering
Alt 7.................Post Processing
* No longer in the menu bar, but the shortcuts still work.
175
◆ L e v e l 0 T u r n i n g GFK-1701
GEOMETRY EXPERT
Arrow Keys: Move through cells in the spreadsheet. Move down to the next row when editing existing
rows.
Tab Key: Move through cells in one row.
Alt + Click Geometry: Enter feature dimensions in cells of the spreadsheet. Hold down the Alt Key and
select a point or feature. The appropriate dimension for the selected feature will be entered in the
active cell of the spreadsheet.
Ctrl I: Insert new row into spreadsheet above the selected row.
Ctrl K: Delete selected row from the spreadsheet.
Ctrl A: Toggle between the possible intersections between features available when post targeting.
Ctrl F1: Line Feature Type
Ctrl F2: Chamfer Feature Type
Ctrl F3: Fillet Feature Type
Ctrl F4: Clockwise Arc Feature Type
Ctrl F5: Counter-Clockwise Feature Type
Ctrl F6: Close Shape
Ctrl F7: Save as Macro
GEOMETRY SELECTION
Shift + Click Geometry: Select multiple features or points.
Ctrl + Drag Rectangle: Select all geometry within the area created by dragging the rectangle.
MACHINING MARKERS
Ctrl + Click Feature: End Feature and End Point Machining Markers move to the position that is
clicked. The Markers do not need to be dragged.
TILE LISTS
Alt + Click Tiles: Select a group of contiguous tiles by selecting the first tile, and then clicking on the
last tile in the group while holding down the Alt key. All tiles in between become selected.
Shift + Click Tiles: Select multiple, non-contiguous tiles.
Shift + Double Click Empty Tile Location: Move all lower tiles up one in tile list.
Shift + Double Click Insertion Point: Create an empty tile location.
Click + Drag Scroll Arrow: Scroll through tile lists a page at a time. Hold down scroll arrow and drag
cursor in the direction of the arrow. The arrow turns red when scrolling the list a page at a time.
176
GFK-1701 S h o r t c u t s ◆
M A C I N T O S H S H O RT C U T S
Certain items in the pull down menus have a symbol and a letter next to them. The symbol
(") signifies that the Apple command key can be depressed at the same time as the letter to access
those items.
View Menu
MENU ITEMS " E.................Top View
File Menu " F.................Front View
" N ................New File " G ................Right View
" O ................Open File " I..................Isometric View
" W ...............Close Window " H ................Home View
" S.................Save " U ................Unzoom
" P.................Print Drawing " R ................Redraw
" Q ................Quit " +.................Zoom In
Edit Menu " -..................Zoom Out
" Z.................Undo
" L.................Labels
" X ................Cut
" C ................Copy " J..................Draw Points
" V ................Paste " [..................Show Geometry
" A ................Select All " `..................Shrink Wrap
" I..................Insert Row Modify Menu
" K ................Delete Row " D ................Duplicate
" A ................Use Intersection #1/#2 " Y ................Set Default
Palettes Menu* Help Menu
" 1 .................Document Control " B ................Balloons
" 2 .................Geometry Creation
" 3 .................Tools
" 4 .................Machining
" 5 .................Views
" 6 .................Cut Part Rendering
" 7 .................Post Processing
* No longer in the menu bar, but the shortcuts still work.
GEOMETRY EXPERT
Arrow Keys: Move through cells in the spreadsheet. Move down to the next row when editing existing
rows.
Tab Key: Move through cells in one row.
" + Click Geometry: Enter feature dimensions in cells of the spreadsheet. Hold down the Alt Key and
select a point or feature. The appropriate dimension for the selected feature will be entered in the
active cell of the spreadsheet.
Control I: Insert new row into spreadsheet above the selected row.
Control K: Delete selected row from the spreadsheet.
Control A: Toggle between the possible intersections between features available when post targeting.
Control 1: Line Feature Type
177
◆ L e v e l 0 T u r n i n g GFK-1701
GEOMETRY SELECTION
Shift + Click Geometry: Select multiple features or points.
Option + Drag Rectangle: Select all geometry within the area created by dragging the rectangle.
MACHINING MARKERS
Control + Click Feature: End Feature and End Point Machining Markers move to the position that is
clicked. The Markers do not need to be dragged.
TILE LISTS
" + Click Tiles: Select a group of contiguous tiles by selecting the first tile, and then clicking on the
last tile in the group while holding down the Alt key. All tiles in between become selected.
Shift + Click Tiles: Select multiple, non-contiguous tiles.
Shift + Double Click Empty Tile Location: Move all lower tiles up one in tile list.
Shift + Double Click Insertion Point: Create an empty tile location.
Click + Drag Scroll Arrow: Scroll through tile lists a page at a time. Hold down scroll arrow and drag
cursor in the direction of the arrow. The arrow turns red when scrolling the list a page at a time.
178
GFK-1701 I n d e x ◆
Index
ID to ID, 78
OD to Face, 75
A OD to OD, 75
Actions, 7, 14, 25, 28, 79, 168 Fixed Clearance, 19, 70-71
Approach Type Clipboard, 9, 16, 28-29, 168
Contour Process, 58, 121-123, 132-133, 143, Colors, 16, 125, 164
146, 154 Com Set-Up dialog, 92
Rough Process, 58, 61, 127, 129-131, 136, Communications, 89, 92-94, 167
140, 142, 144-145, 152-153 Contouring Function, 57, 120, 131, 142, 145, 153
Thread Process, 58, 66, 157-158 Contour Process, 58, 121-123, 132-133, 143,
Auto Clearance, 18-19, 58-59, 62-65, 67, 69-71, 146, 154
96-97, 125-126, 132, 136, 159 Contour Style, 60
Coolant, 60, 66, 68, 70
B Cursors, 6
Balloons Cut Direction, 13, 59, 61, 78, 123, 130
Error Balloons, 14, 25-27 Cut Shapes, 56, 129
Blueprint, Tutorial Part, 161 Cutter, Side and Direction, 13
C D
Clearance diagrams Dialogs, 6-9, 11, 14, 17-18, 57-58, 62, 71, 109,
Roughing Cycles (Processes), 62 136
Pattern Shift Rough, 64 Do it button, 56-57, 124, 126, 134-135, 147, 155,
Plunge Rough, 63 158, 179
Turn Rough, 62, 130 Document Control button, 17, 33, 35, 95, 98, 119
Thread (Process), 58, 66, 157-158 Document Control dialog, 17, 33, 35, 59, 62-64,
Clearance Moves 70-71, 95-96, 98, 119, 125-126
Auto Clearance, 18-19, 58-59, 62-65, 67, 69- Drawing Window, 8, 16, 29, 168
71, 96-97, 125-126, 132, 136, 159 Drilling Function, 12, 50, 57, 149
Clearance Move diagrams Drilling Process, 58, 68, 150
Approaches from Tool Change Position
Face Approach, 72 E
ID Approach, 73 Edit Menu, 3, 9, 16, 20, 26-28, 168, 173, 175,
OD Approach, 72 177
Exits to Tool Change Position End Feature, 13, 56, 59, 78-79, 123, 134, 174,
Face Exit, 74 176, 178
ID Exit, 74 End Point, 13, 23, 26-27, 56, 59-61, 65, 72, 78-
OD Exit, 73 79, 107, 123-124, 131, 134, 136, 153-154, 174,
Same Tool Operations 176, 178
Face to Face, 77 Entry Moves, 59
Face to ID, 76 Error Balloons, 14, 25-27
Face to OD, 76 Exit Moves, 65, 69-71, 97, 132, 149
ID to Face, 77
179
◆ L e v e l 0 T u r n i n g GFK-1701
F O
File Compatibility, 163 Open dialog, 11, 17, 19, 35, 96, 163, 166
File Extensions, 89-90, 94, 163 Operation Data, 30-31, 79, 172
File Menu, 17, 32, 55, 80, 88, 90-94, 119, 163, Operation Summary, 80, 172
165-166, 172-173, 175, 177 Operation tiles, 12, 57, 120, 135
Function tiles, 8, 12, 56, 120 Operations list, 57-58, 126, 135, 159
Operating Systems Glossary, 4, 162
G
Geometry Creation Palette, 8, 22, 25, 36, 100, PQ
172 Palettes, 4, 6-8, 14, 173, 175, 177
Geometry Exercise, 33 Pattern Shift Roughing Cycle
Geometry Expert, 8, 10, 20-30, 33, 36-37, 39, 47, See: Rough Processes (Roughing Cycles)
100, 169, 174, 176-177 Peck, 63-64, 69, 142, 145, 150-151
Graphic User Interface (GUI), 6 Plunge Roughing Cycle
Groove Tools, 63, 115, 128, 141 See: Rough Processes (Roughing Cycles)
Pop-up menus, 9-10, 50, 110
Post Processor button, 89
HIJ Post Processor dialog, 89-90, 93-94, 168
Help Menu Preferences
See: Balloons Com Set-Up, 92, 167
Prompting File Extensions, 89-90, 94, 163
Inserts, 50-53, 109 Interface, 5-9, 11, 13, 15, 28, 49, 117, 167,
175
KL Monitor, 83, 167, 170
Post Processor, 18, 79, 89-91, 93-94, 163,
Keyboard Shortcuts, 13, 23, 175
167-168
Launching the System, 33, 95, 162
Printing, 32, 80-81, 88, 164-165, 167-168
Rendering, 8, 16, 58, 82, 85-88, 99, 137-138,
MN 147-148, 155, 159, 167, 173, 175, 177
Machining button, 56, 119-120 Printing
Machining Markers, 7, 13, 56, 59-61, 65, 78-79, Rendered Image, 84-85, 88, 148, 155, 160,
123, 125, 133-134, 146-147, 153-154, 174, 176, 164, 168, 170
178 Summaries, 119, 168
Machining palette, 8, 12, 56-58, 120, 124, 159, Toolpaths, 8, 16, 18, 56-58, 60, 65, 70, 80,
172 83, 89, 93, 97, 99, 109, 111, 135-136, 147,
Material Only, 18, 57-58, 60, 62, 65, 96, 122- 159, 164, 168, 170, 172
124, 131, 136, 140, 144, 147, 152, 159 Process dialogs, 57-58, 71
Math Functions, 9 Process list, 8, 12, 56-58, 119-121, 126-127, 129,
Menu Bar, 13, 173, 175, 177 131, 133, 139, 142-146, 148-149, 151, 153, 156,
Multiple Process Programming, 57, 126, 131, 159
136, 147 Process tiles, 12, 56, 120, 126
Prompting, 4, 14, 22, 25-27, 38, 172
180
GFK-1701 I n d e x ◆
T
Text Boxes, 9, 18-20, 30, 54, 59, 62, 71, 79, 97,
150, 158, 171
Threading Function, 56-57, 66, 156
Thread Process, 58, 66, 157-158
Tile lists, 7, 12, 49, 117, 174, 176, 178
Tiles, 6, 8, 12, 15, 56-57, 109, 117, 120, 126,
135-136, 139, 148, 156, 174, 176, 178
Tool Change, 16-17, 19, 35, 70-73, 90, 96-98,
125, 136, 179
Tool Creation dialog, 1, 49, 109
Tool List button, 49, 109
Tool List Summary, 55, 119, 172
Tool list, 12, 49, 54-56, 58, 61, 68, 109, 112-117,
119, 156, 172
Tool tiles, 12, 56, 109
181