Professional Documents
Culture Documents
Catalogue RAC Mitsubishi Electric
Catalogue RAC Mitsubishi Electric
Refrigerant piping Liquid pipe mm (in) 9.52 (3/8) Brazed 9.52 (3/8) Brazed
diameter Gas pipe mm (in) 22.2 (7/8) Brazed 22.2 (7/8) Brazed
Type × Quantity Propeller fan×1 Propeller fan×1
m3/min 170 170
Airflow rate L/s 2,834 2,834
FAN cfm 6,003 6,003
Inverter-control, Inverter-control,
Control, Driving mechanism
Direct-driven by motor Direct-driven by motor
Motor output kW 0.92×1 0.92×1
External static pressure 0Pa (0mmH2O) 0Pa (0mmH2O)
Type MITSUBISHI ELECTRIC Inverter scroll hermetic compressor
Starting method Inverter Inverter
Compressor Motor output kW 5.4 7.5
Case heater kW 0.045 0.045
Lubricant MEL56 MEL56
Pre-coated galvanized steel sheets
External finish (+powder coating for -BS type)
<MUNSELL 3.0Y 7.8/1 1 or similar>
mm 1650×920×740 1650×920×740
External dimension H × W × D
in 64-31/32×36-1/4×29-5/32 64-31/32×36-1/4×29-5/32
High pres. Sensor & High pres. High pres. Sensor & High pres.
High pressure protection
Switch at 4.15MPa (601psi) Switch at 4.15MPa (601psi)
Inverter circuit Over-heat protection, Over-heat protection,
Protection devices (COMP. / FAN) Over-current protection Over-current protection
Compressor - -
Fan motor Thermostat Thermostat
Type × original charge R410A×5.5kg (13lbs) R410A×6.5kg (15lbs)
Refrigerant
Control LEV and HIC circuit LEV and HIC circuit
Net weight kg 180 193
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
Note 1. Cooling capacity indicates the value at operation under the following conditions.
Indoor : 27°CDB / 19.5°CWB, Outdoor : 35°CDB
2. <Reference cooling capacity> Indicates the value at operation under the following conditions.
Indoor : 27°CDB / 19°CWB, Outdoor : 35°CDB
3. The sound pressure level is measured in an anechoic room.
4. Long period operation in a high temperature and humidity atmosphere (dew point of 23°C or more) may cause condensation to form in the indoor unit.
5. Cooling Seasonal Performance Factor
3
Cooling only series [ OUTLINE DIMENSIONS ]
<Accessory>
∙ Pipe cover ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ 2pcs.
(For dew condensation prevention of 2×10-ø3 Holes 124 1302
local piping and unit connection.) 66 130×9=1170
Return air
∙ Remote controller ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙1pc. 42
duct flange
100
Rubber bush <Remote Control box
controller wiring>
129
199
70 75
Rubber bush
<Outdoor unit
462
connection wiring>
200
20 1500 20
Rubber bush
55
<Power supply wiring> 2×8-ø3.1 Holes
131
A
40
10
Supply air
4-ø12 Holes 130 duct flange
<For hanging bolt M10> 45 130×7=910
[Field supply]
Top view
73
25
95
144
130
100
330
376
400
262
145
250
A
130
100
11
39 565 1484
Unit : mm
·Remote controller·················1pcs.
47
108
36-ø3 HOLES
23 1876 23
Control box
53 83 60
54
1121
267
Rubber bush
Rubber bush
<Power supply
wiring> <Remote
controller wiring>
399
Rubber bush
<Outdoor unit
connection wiring> 24-ø3.1 HOLES
A
Supply air
31
130
10
duct flange
42.5 8X130(=1040) 42.5 4-HOLES
<For hanging bolt>
[Field supply]
Top view
Refrigerant pipe
ø25.4 (1 braze) 1965
1300
1922
50 1200 50 61 61
1800
10
22.5
185
120
40
255
4X120(=480)
525
130 130
560
595
201 117
340
1824
21
40
22.5
A
Refrigerant pipe
PEV-P400YM:ø12.7 39 1238
Front view
PEV-P500YM:ø15.88
Left side view Unit : mm
3
Cooling only series [ OUTLINE DIMENSIONS ]
PUV-P200, 250YM-A
<Accessories>
Connecting pipe
<Gas> •Pipe (ID25.4XOD22.2)····P200,P250 1pc.
<Liquid> •Pipe (ID9.52XOD9.52)····P200,P250 1pc.
740
Note1. Please refer to the Installation Manual for information
regarding necessary spacing around the
unit and foundation work.
2. At brazing of pipes,wrap the refrigerant service valve
920 with wet cloth and keep the temperature of
Top view refrigerant service valve under 120°C.
Discharge air
303
Connecting pipe specifications
1650
*1 Connect by using the connecting pipes (for bottom piping and front piping)
that are supplied.
1347
Service
Refrigerant service valve panel
<gas>
4
Refrigerant service valve 7 1
<liquid>
88
72
54
262
222
131
For wires
137
84
(Mounting pitch)
(740)
2
681
6
Refrigerant service Refrigerant service
valve <liquid> valve <gas>
80 760 80
29.5
(Mounting pitch)
Bottom view
Unit : mm
PUV-P400YM-A
<Accessories>
●Connecting pipe
<Gas> •Elbow (ID28.58XOD28.58)····P400 1pc.
<Liquid> •Pipe (ID15.88XOD15.88)····P400 1pc.
•Pipe reducer(ID15.88XOD12.7)····P400 1pc.
740
Intake Intake *1 Connect by using the connecting pipes (for bottom piping and front piping)
Intake air air that are supplied.
air
1650
Service
1347
For pipes
54
238
131
57 20 20 57 254 98 2X2-80X35 Oval hole 4 Front through hole ø52 or ø27 Knockout hole
586 301 102 <Sling hole> For wires
5 Bottom through hole ø65 Knockout hole
Left side view Front view
6 Bottom through hole ø52 Knockout hole
272 150 2X2-14X20 Oval hole
301 83 7 For transmission cables Front through hole ø34 Knockout hole
29.5
145
227
84
121
144
196
(Mounting pitch)
5
94
(740)
681
2 Refrigerant service
6 valve <gas>
Refrigerant service
valve <liquid>
80 1060 80
29.5
(Mounting pitch)
Bottom view
Unit : mm
3
Indoor unit
Medium static pressure type
Indoor unit
G
0R H 3() 3 0 ( 3() 3 0 (
3R HU VR UFH SKDVH 9 ]
Cooling capacity kW
1RPL DO 78 K
Heating capacity kW
1RPL DO 78 K
3R HU RROL J kW > >
FR V PSWLR HDWL J kW
UUH W RROL J > >
HDWL J
External nish *DOYD L]HG VWHHO SODWH
Remote Controller
LPH VLR [:[ PP [ [ [ [
L [ [ [ [
1HW HLJKW kg (lbs.) > >
HDW H[FKD JHU Cross n (Aluminum n and copper tube)
)D Type x Quantity 6LURFFR ID [
Air ow rate P PL
/R 0LG L /V
FIP
([WHU DO VWDWLF
3D
SUHVV UH
0RWRU Type PRWRU
2 WS W kW
Air lter PP honeycomb fabric.
5HIULJHUD W /LT LG
PP L UD]HG UD]HG
SLSH GLDPHWHU 5
*DV
PP L UD]HG UD]HG
5
)LHOG GUDL SLSH GLDPHWHU PP L 2 2
6R G SUHVV UH OHYHO PHDV UHG L D HFKRLF URRP
Lossnay
/R 0LG L G
G
1RWHV
1RPL DO FRROL J FR GLWLR V 0HDV UHG L D HFKRLF URRP LWK D P DLU L OHW G FW D G Aux. duct
, GRRU ) ) : 2 WGRRU ) 2m air outlet duct attached to the unit and 1.5m below
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW WKH LW
1RPL DO KHDWL J FR GLWLR V 2m 2m
1.5m
, GRRU ) 2 WGRRU ) ):
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW
7KH YDO HV DUH PHDV UHG DW WKH UDWHG H[WHU DO VWDWLF SUHVV UH Measurement location
*4 The rated external static pressure is shown without < >. The factory setting is the rated value.
0HDV UHG L D HFKRLF URRP LWK D P DLU L OHW G FW D G > LV L FDVH RI 3()< 3 90 / (
Aux. duct
2m air outlet duct attached to the unit and 1.5m below
WKH LW
2m 1m
1.5m
Measurement location
Specifications
0R H 3() 3 0 ( 3() 3 0 (
3R HU VR UFH SKDVH 9 ]
Cooling capacity kW
1RPL DO 78 K
Heating capacity kW
1RPL DO 78 K
3R HU RROL J kW > >
FR V PSWLR HDWL J kW
UUH W RROL J > >
HDWL J
External nish *DOYD L]HG VWHHO SODWH
LPH VLR [:[ PP [ [ [ [
L [ [ [ [
1HW HLJKW kg (lbs.) > >
HDW H[FKD JHU Cross n (Aluminum n and copper tube)
)D Type x Quantity 6LURFFR ID [ 6LURFFR ID [
Air ow rate P PL
/R 0LG L /V
FIP
([WHU DO VWDWLF
3D
SUHVV UH
0RWRU Type PRWRU
2 WS W kW
Air lter PP honeycomb fabric.
5HIULJHUD W /LT LG
PP L UD]HG UD]HG
SLSH GLDPHWHU 5
*DV
PP L UD]HG UD]HG
5
)LHOG GUDL SLSH GLDPHWHU PP L 2 2
6R G SUHVV UH OHYHO PHDV UHG L D HFKRLF URRP
/R 0LG L G
G
0R H 3() 3 0 ( 3() 3 0 (
3R HU VR UFH SKDVH 9 ]
Cooling capacity kW
1RPL DO 78 K
Heating capacity kW
1RPL DO 78 K
3R HU RROL J kW > >
FR V PSWLR HDWL J kW
UUH W RROL J > >
HDWL J
External nish *DOYD L]HG VWHHO SODWH
LPH VLR [:[ PP [ [ [ [
L [ [ [ [
1HW HLJKW kg (lbs.) > >
HDW H[FKD JHU Cross n (Aluminum n and copper tube)
)D Type x Quantity 6LURFFR ID [
Air ow rate P PL
/R 0LG L /V
FIP
([WHU DO VWDWLF
3D
SUHVV UH
0RWRU Type PRWRU
2 WS W kW
Air lter PP honeycomb fabric.
5HIULJHUD W /LT LG
PP L UD]HG UD]HG
SLSH GLDPHWHU 5
*DV
PP L UD]HG UD]HG
5
)LHOG GUDL SLSH GLDPHWHU PP L 2 2
6R G SUHVV UH OHYHO PHDV UHG L D HFKRLF URRP
/R 0LG L G
G
1RWHV
1RPL DO FRROL J FR GLWLR V 0HDV UHG L D HFKRLF URRP LWK D P DLU L OHW G FW D G Aux. duct
, GRRU ) ) : 2 WGRRU ) 2m air outlet duct attached to the unit and 1.5m below
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW WKH LW
1RPL DO KHDWL J FR GLWLR V 2m 2m
1.5m
, GRRU ) 2 WGRRU ) ):
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW
7KH YDO HV DUH PHDV UHG DW WKH UDWHG H[WHU DO VWDWLF SUHVV UH Measurement location
*4 The rated external static pressure is shown without < >. The factory setting is the rated value.
0HDV UHG L D HFKRLF URRP LWK D P DLU L OHW G FW D G > LV L FDVH RI 3()< 3 90 / (
Aux. duct
2m air outlet duct attached to the unit and 1.5m below
WKH LW
2m 1m
1.5m
Measurement location
Indoor unit
High static pressure type
Indoor unit
Air lter Option:Synthetic ber unwoven cloth lter (long life lter) and lter box are recommended.
5HIULJHUD W *DV
PP L UD]HG UD]HG
SLSL J GLDPHWHU 5
/LT LG
PP L UD]HG UD]HG
5
)LHOG GUDL SLSH GLDPHWHU PP L 2
Remote Controller
FR V PSWLR HDWL J kW
UUH W RROL J 9 ─
9 ─
HDWL J 9 ─
9 ─
External nish *DOYD L]HG *DOYD L]HG VWHHO SODWH
LPH VLR [:[ PP [ [
L [ [
1HW HLJKW kg (lbs.)
HDW H[FKD JHU Cross n (Aluminum plate n and copper tube)
)D Type x Quantity 6LURFFR ID [
Air ow rate P PL ─
/V ─
FIP ─
/R 0LG L P PL ─
/V ─
FIP ─
([WHU DO 9 3D ─
VWDWLF 9 3D ─
Lossnay
SUHVV UH 3D ─
PP 2 ─
0RWRU Type SKDVH L G FWLR PRWRU PRWRU
2 WS W kW
Air lter (option) Synthethic ber unwoven cloth lter (long life) Synthethic ber unwoven cloth lter (long life lter) and lter box are recommended.
5HIULJHUD W *DV
PP L
SLSH GLDPHWHU UD]L J
/LT LG
PP L
UD]L J
)LHOG GUDL SLSH GLDPHWHU PP L 2
6R G SUHVV UH 9 G 3D 3D 3D 3D ─
OHYHO 9 G 3D 3D 3D 3D ─
/R 0LG L G ─
Precautions for use
1RWHV
1RPL DO FRROL J FR GLWLR V *5 Cooling/heating capacity indicates the maximum value at operation under the following condition.
Indoor: 27˚CD.B./19˚CW.B. (81˚FD.B./66˚FW.B.), Outdoor: 35˚CD.B. (95˚FD.B.) RROL J , GRRU ) ) : 2 WGRRU )
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW HDWL J , GRRU ) 2 WGRRU ) ):
*2 The values are measured at the factory setting of external static pressure. *6 The external static pressure is set to 220Pa (at 380V) /260Pa (at 400, 415V) at factory shipment.
1RPL DO KHDWL J FR GLWLR V 7KH YDO H DUH WKDW DW 9
Indoor: 20˚CD.B. (68˚FD.B.), Outdoor: 7˚CD.B./6˚CW.B. (45˚FD.B./43˚FW.B.) ,W LV PHDV UHG L D HFKRLF URRP
3LSH OH JWK P IW /HYHO GLIIHUH FH P IW 7KH UDWHG H[WHU DO VWDWLF SUHVV UH LV VKR LWKR W
*4 The factory setting of external static pressure is shown without < >. The factory setting is the rated value.
5HIHU WR )D FKDUDFWHULVWLFV F UYHV DFFRUGL J WR WKH H[WHU DO VWDWLF SUHVV UH L 7 22. IRU WKH ,W LV PHDV UHG DW WKH UDWHG H[WHU DO VWDWLF SUHVV UH L D HFKRLF URRP
usable range of air ow rate.
1. SPECIFICATIONS Y-Series (Cooling-only)
PUCY-P-Y(S)KD, EP-YSKD
Current input A 53.1-50.5-48.7
EER kW/kW 3.30
Cooling capacity *3 kW 105.7
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling Outdoor D.B. 10.0~52.0°C (50~126°F)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P15~P500/1~50
Sound pressure level (measured in anechoic room) dB <A> 67.5
Refrigerant Liquid pipe mm (in.) 19.05 (3/4) Brazed
piping diameter Gas pipe mm (in.) 41.28 (1-5/8) Brazed
Set Model
Model PUCY-P450YKD (-BS) PUCY-P500YKD (-BS)
FAN Type x Quantity Propeller fan x 1 Propeller fan x 2
Air flow rate m3/min 210 320
L/s 3,500 5,333
cfm 7,415 11,299
Control, Driving mechanism Inverter-control, Direct-driven by motor Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1 0.92 x 2
*2 External static press. 0 Pa (0 mmH2O) 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor Inverter scroll hermetic compressor
Starting method Inverter Inverter
Motor output kW 12.4 13.3
Case heater kW - -
Lubricant MEL32 MEL32
Pre-coated galvanized steel sheets (+powder coating for -BS Pre-coated galvanized steel sheets (+powder coating for -BS
External finish
type) type)
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D mm 1,650 x 1,220 x 740 1,650 x 1,750 x 740
in. 65 x 48-1/16 x 29-3/16 65 x 68-15/16 x 29-3/16
High pressure sensor, High pressure switch at 4.15 MPa (601 High pressure sensor, High pressure switch at 4.15 MPa (601
Protection devices High pressure protection
psi) psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Compressor - -
Fan motor - -
Refrigerant Type x original charge R410A x 11.5 kg (26 lbs) R410A x 11.8 kg (27 lbs)
Control LEV and HIC circuit
Net weight kg (lbs) 236 (521) 304 (671)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe mm (in.) 15.88 (5/8) Brazed 15.88 (5/8) Brazed
distributor Gas pipe mm (in.) 28.58 (1-1/8) Brazed 28.58 (1-1/8) Brazed
Drawing External WKL94T417
Wiring WKE94G899 WKE94G900
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Outdoor Twinning kit: CMY-Y200VBK2
Joint: CMY-Y102SS/LS-G2, CMY-Y202/302S-G2
Header: CMY-Y104/108/1010-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
MEES18K047 17
1. SPECIFICATIONS Y-Series (Cooling-only)
PUCY-P-Y(S)KD, EP-YSKD
Current input A 50.0-47.5-45.8
EER kW/kW 3.88
Cooling capacity *3 kW 116.9
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling Outdoor D.B. 10.0~52.0°C (50~126°F)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P15~P500/2~50
Sound pressure level (measured in anechoic room) dB <A> 66.5
Refrigerant Liquid pipe mm (in.) 19.05 (3/4) Brazed
piping diameter Gas pipe mm (in.) 41.28 (1-5/8) Brazed
Set Model
Model PUCY-P300YKD (-BS) PUCY-P300YKD (-BS) PUCY-P450YKD (-BS)
FAN Type x Quantity Propeller fan x 1 Propeller fan x 1 Propeller fan x 1
Air flow rate m3/min 175 175 210
L/s 2,917 2,917 3,500
cfm 6,179 6,179 7,415
Control, Driving mechanism Inverter-control, Direct-driven by motor Inverter-control, Direct-driven by motor Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1 0.92 x 1 0.92 x 1
*2 External static press. 0 Pa (0 mmH2O) 0 Pa (0 mmH2O) 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor Inverter scroll hermetic compressor Inverter scroll hermetic compressor
Starting method Inverter Inverter Inverter
Motor output kW 8.1 8.1 12.4
Case heater kW - - -
Lubricant MEL32 MEL32 MEL32
Pre-coated galvanized steel sheets Pre-coated galvanized steel sheets Pre-coated galvanized steel sheets
External finish
(+powder coating for -BS type) (+powder coating for -BS type) (+powder coating for -BS type)
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D mm 1,650 x 920 x 740 1,650 x 920 x 740 1,650 x 1,220 x 740
in. 65 x 36-1/4 x 29-3/16 65 x 36-1/4 x 29-3/16 65 x 48-1/16 x 29-3/16
High pressure sensor, High pressure High pressure sensor, High pressure High pressure sensor, High pressure
Protection devices High pressure protection
switch at 4.15 MPa (601 psi) switch at 4.15 MPa (601 psi) switch at 4.15 MPa (601 psi)
Over-heat protection, Over-current pro- Over-heat protection, Over-current pro- Over-heat protection, Over-current pro-
Inverter circuit (COMP./FAN)
tection tection tection
Compressor - - -
Fan motor - - -
Refrigerant Type x original charge R410A x 6.5 kg (15 lbs) R410A x 6.5 kg (15 lbs) R410A x 11.5 kg (26 lbs)
Control LEV and HIC circuit
Net weight kg (lbs) 200 (441) 200 (441) 236 (521)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe mm (in.) 12.7 (1/2) Brazed 12.7 (1/2) Brazed 15.88 (5/8) Brazed
distributor Gas pipe mm (in.) 22.2 (7/8) Brazed 22.2 (7/8) Brazed 28.58 (1-1/8) Brazed
Drawing External WKL94T419
Wiring WKE94G899 WKE94G899 WKE94G899
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Outdoor Twinning kit: CMY-Y300VBK3
Joint: CMY-Y102SS/LS-G2, CMY-Y202/302S-G2
Header: CMY-Y104/108/1010-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
MEES18K047 19