Professional Documents
Culture Documents
1HB2
1HB2
rpf
Licensee
AECOM Singapore Pte Ltd
300 Beach Road
#03-00 The Concourse
Singapore 199555
10479063400712WPN11
Input
General
Design Code List Singapore - Eurocode 2*SAVED*
Material List Singapore - Singapore Eurocode Materials*SAVED*
Reinforcement Type List Reinforced
Member Type List Beam
Panel Type List Internal
Strip Type List One way - Nominal Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
Concrete - Spanning Members List C36/45MPa
Concrete - Columns List C36/45MPa
Top Reinforcement Cover mm 50
Bottom Reinforcement Cover mm 50
Top Reinforcement Axis Depth Limit mm 30
Bottom Reinforcement Axis Depth Limit mm 30
Concrete Unit Weight kn/m3 25
Self Weight Definition List Program Calculated
Pattern Live Load Y/N
Earthquake Design List None
Moment Redistribution % 0
Design Surface Levels List Reduced Levels
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data
have been multiplied in the calculatiuons by 0.8
Span
Span Span Slab Panel Panel
Length Depth Width Width
Left Right
mm mm mm mm
LE 0
1 13333 1350 1025 1025
RE 0
Columns
Column Column Support Transverse Transverse
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
1 1 Knife-Edge 1025
2 2 Knife-Edge 1025
Beams
Beam Beam Beam Beam Effective
Number Depth Width Width Flange
at Slab Width
mm mm mm mm
1 1350 1025 1025 1025
RAPT 6.6.2.0 19/3/2020 10:40:01 PM Page 2/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Elements : Trapezoidal
Element Description Solid/Void Depth Element Width Width Width Width Left End Distance to Left Right End Distance to Right
Top Depth Top Top Bottom Bottom Reference End from Left Reference End from Right
Left Right Left Right Column Reference Column Reference
Column Column
A List mm mm mm mm mm mm # mm # mm
1 new element 750 600 512.5 512.5 512.5 512.5 1 0 1 1000
2 new element 550 800 512.5 512.5 512.5 512.5 1 12433 2 0
Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection Case
80 L1 800
60 600
40 400
20 200
0 0
1 2
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List
1 Bar 1 0 0 50 2 0 0 50 40 20
Design Zones
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size
Column bar end end Column bar end Right End
List # mm mm mm # mm mm mm List List
1 Bar 1 0 0 50 2 0 0 50 40 20
-300
-600
-900
-1200
0 13333mm
Design Data
Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Ductility Check at Left End Column Y/N Y
Ductility Check at Right End Column Y/N Y
Minimum Reinforcement Strength Limit - #.## x M* #.# 0
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
Shear Enhancement at Supports Y/N N
Ast Value in Shear Calculations List Calculated
Limit Reinforcement Strain Y/N Y
Include Strain Hardening of Reinforcement Y/N N
Beam Shear Critical Section Location List Code Critical Section
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C36/45MPa
Characteristic Compressive Strength MPa 45
Mean Compressive Strength MPa 55
Lower Characteristic Tensile Strength MPa 2.29
RAPT 6.6.2.0 19/3/2020 10:40:05 PM Page 6/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Limit Flexure Shear - Flexure - Shear Reinforcement for
Shear
T Deformed 460 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Description
Elevation view
1 2
mm
0
-300
-600
-900
-1200
0 13333mm
Plan view
1 2
mm
-400
-200
200
400
0 13333mm
Warnings
Input
No errors or warnings were found.
RAPT 6.6.2.0 19/3/2020 10:40:06 PM Page 7/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Output
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit.
Warning:Total Deflection span/deflection ratio in at least one span is less than defined limit.
Warning:Incremental deflection in at least one span is greater than defined limit.
Warning:Total deflection in at least one span is greater than defined limit.
Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See
Detailed Reinforcement Design Comments.
Bending Moments
Load Cases
Column Actions
Col No. 1 Self Initial Live
Weight Dead Load
Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0
Reaction kN 215.2 1339.15 287.5
Elastic Rotation #.# 5.41e-4 3.42e-3 7.62e-4
Elastic Axial Shortening mm 0 0 0
Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 1841.85 1841.85 1698.1 1698.1 2529.63 2529.63 1985.6 2529.63
Elastic Rotation #.# 4.72e-3 4.72e-3 4.34e-3 4.34e-3 6.49e-3 6.49e-3 5.1e-3 6.49e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 1390.87 1390.87 1304.62 1304.62 1903.55 1903.55 1477.12 1903.55
Elastic Rotation #.# -4.79e-3 -4.79e-3 -4.44e-3 -4.44e-3 -6.57e-3 -6.57e-3 -5.14e-3 -6.57e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Ultimate Flexure
1 2
kNm 252 190
0
2000
4000
6000
8000
10000
9527
0 13333mm
1 2
kN
2800 2389
2100
1400
700
0
-700
-1400
-2100
-1850
0 13333mm
Flexural Design
Ultimate
1 2
mm2
80000 0
4000
0
-4000
-8000
-12000
-16000
-20000
-24000
22493
-28000
0 13333mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
1 2
kNm
0
2000
4000
6000
8000
10000
0 13333mm
1 2
0.09
0
-0.09
-0.18
-0.27
-0.36
-0.45
-0.54
0.545
-0.63
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Permanent
Maximum Moment Condition
MPa1 2MPa
-24 -17.02 -280
-18 -210
-12 -140
-6 -70
0 0
6 70
12 140
18 210
24 280
19.68
30 350
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
MPa1 2MPa
-24 -17.02 -280
-18 -210
-12 -140
-6 -70
0 0
6 70
12 140
18 210
24 280
19.68
30 350
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.2.0 19/3/2020 10:40:09 PM Page 10/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Characteristic Service
Maximum Moment Condition
1 2
MPa MPa
-18.69
-21 -270
-14 -180
-7 -90
0 0
7 90
14 180
21 270
28 21.61 360
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
MPa MPa
-18.69
-21 -270
-14 -180
-7 -90
0 0
7 90
14 180
21 270
28 21.61 360
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Shear Design
Beam
Span 1
Locat V* Mv* Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Deflections
All Spans Loaded
Transfer
mm1 2
0
-3.05
-40
-80
-120
-160 4378
0 13333mm
Short Term
mm1 2
0
-40 -31.1
-80
-120
-160
428
0 13333mm
RAPT 6.6.2.0 19/3/2020 10:40:11 PM Page 12/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Incremental
mm1 2
0
-40 -31.3
-80
-120
-160
427
0 13333mm
mm1 2
0
-40
-80 -59.3
-120
-160
225
0 13333mm
Span 1
Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 427
- Total Span/Deflection ratio less than user defined limit = 225
- Incremental Deflection greater than user defined limit = -31.3mm
- Total Deflection greater than user defined limit = -59.3mm
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to
use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than
calculated. RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 7905.24mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 5948.63mm2
Reinforcement Layout
1 2
mm
0
-300 18-T40
-600
18-T40
-900
-1200
18-T40
0 13333mm
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to
use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than
calculated. RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 7905.24mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 5948.63mm2