Professional Documents
Culture Documents
1 HB8 A
1 HB8 A
rpf
Licensee
AECOM Singapore Pte Ltd
300 Beach Road
#03-00 The Concourse
Singapore 199555
10479063400712WPN11
Input
General
Design Code List Singapore - Eurocode 2*SAVED*
Material List Singapore - Singapore Eurocode Materials*SAVED*
Reinforcement Type List Reinforced
Member Type List Beam
Panel Type List Internal
Strip Type List One way - Nominal Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
Concrete - Spanning Members List C36/45MPa
Concrete - Columns List C36/45MPa
Top Reinforcement Cover mm 50
Bottom Reinforcement Cover mm 50
Top Reinforcement Axis Depth Limit mm 30
Bottom Reinforcement Axis Depth Limit mm 30
Concrete Unit Weight kn/m3 25
Self Weight Definition List Program Calculated
Pattern Live Load Y/N
Earthquake Design List None
Moment Redistribution % 0
Design Surface Levels List Reduced Levels
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data
have been multiplied in the calculatiuons by 0.8
Span
Span Span Slab Panel Panel
Length Depth Width Width
Left Right
mm mm mm mm
LE 0
1 13333 1500 1000 1000
RE 0
Columns
Column Column Support Transverse Transverse
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
1 1 Knife-Edge 1000
2 2 Knife-Edge 1000
Beams
Beam Beam Beam Beam Effective
Number Depth Width Width Flange
at Slab Width
mm mm mm mm
1 1500 1000 1000 1000
RAPT 6.6.2.0 19/3/2020 10:38:46 PM Page 2/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Elements : Trapezoidal
Element Description Solid/Void Depth Element Width Width Width Width Left End Distance to Left Right End Distance to Right
Top Depth Top Top Bottom Bottom Reference End from Left Reference End from Right
Left Right Left Right Column Reference Column Reference
Column Column
A List mm mm mm mm mm mm # mm # mm
1 new element 775 725 500 500 500 500 1 0 1 1000
2 new element 845 655 500 500 500 500 1 12333 2 0
Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection Case
1 2
kN/m
80
60 L2
40 L1 L3
20
0
0 13333mm
1 2
kN/m kN
80 1 2 3 533.33
60 400
40 266.67
20 133.33
0 0
0 13333mm
RAPT 6.6.2.0 19/3/2020 10:38:48 PM Page 4/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
80 L1 533.33
60 400
40 266.67
20 133.33
0 0
1 2
1 2
kN/m kN
80 533.33
60 400
40 1 2 3 266.67
20 133.33
0 0
0 13333mm
Reinforcement
Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Flexural Bar T 460MPa
Flexural Mesh A 500MPa
Shear Option 1 T 460MPa 13 2
Shear Option 2 T 460MPa 13 4
Shear Option 3 T 460MPa 13 6
Punching Shear T 460MPa 10 2
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List
1 Bar 1 0 0 50 2 0 0 50 40 20
Design Zones
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size
Column bar end end Column bar end Right End
List # mm mm mm # mm mm mm List List
1 Bar 1 0 0 50 2 0 0 50 40 20
User Defined
Layer Steel type Left End Distance Bar Top % Development % Development Right End Distance Bar Top % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of
Column end of length at at left Bar in Tension in Compression Column end of length at at Right Bar in Tension
bar left end end bar right end end
List # mm mm mm % % # mm mm mm %
1 T 460MPa 1 0 0 50 0 0 2 0 0 50 0
RAPT 6.6.2.0 19/3/2020 10:38:49 PM Page 5/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Layer % Development Bar Number Spacing % in Layer attached
Number of Right End of Size of Bars of Bars Flange after the
Bar in PreExisting Load
Compression Case
% List # mm % Y/N
1 0 40 10 0 0 N
User Defined
Layer Steel type Left End Distance Bar Bottom % Development % Development Right End Distance Bar Bottom % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of
Column end of length at at Left Bar in Tension in Compression Column end of length at at Right Bar in Tension
bar left end end bar right end End
List # mm mm mm % % # mm mm mm %
1 T 460MPa 1 1000 0 50 100 100 2 -1000 0 50 100
2 T 460MPa 1 1000 0 150 0 0 2 -1000 0 150 0
3 T 460MPa 1 1000 0 100 0 0 2 -1000 0 100 0
1 2
mm
0
-400
-800
-1200
-1600
0 13333mm
1 2
mm
0
-400
-800
-1200
-1600
0 13333mm
Design Data
Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Ductility Check at Left End Column Y/N Y
Ductility Check at Right End Column Y/N Y
Minimum Reinforcement Strength Limit - #.## x M* #.# 0
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
Shear Enhancement at Supports Y/N N
Ast Value in Shear Calculations List Calculated
RAPT 6.6.2.0 19/3/2020 10:38:50 PM Page 6/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C36/45MPa
Characteristic Compressive Strength MPa 45
Mean Compressive Strength MPa 55
Lower Characteristic Tensile Strength MPa 2.29
Upper Characteristic Tensile Strength MPa 4.25
Concrete Density kg/m3 2447
Design Concrete Modulus MPa 32308.3
Mean Concrete Modulus MPa 34313
Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.533
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85
Concrete Strain Limit #.# 0.004
Strength Gain Rate List Normal
Maximum Aggregate Size mm 20
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Limit Flexure Shear - Flexure - Shear Reinforcement for
Shear
T Deformed 460 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Description
RAPT 6.6.2.0 19/3/2020 10:38:51 PM Page 7/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Nominal Bar Bar Area Bar Bar Stock
Bar Size Diameter Inertia Weight Length
A mm mm2 mm4 kg/m mm
10 10 78.5 491.07 0.62 12000
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000
Elevation view
1 2
mm
0
-400
-800
-1200
-1600
0 13333mm
Plan view
1 2
mm
-400
-200
200
400
0 13333mm
Warnings
Input
No errors or warnings were found.
Output
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit.
Warning:Total deflection in at least one span is greater than defined limit.
Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See
Detailed Reinforcement Design Comments.
Bending Moments
Load Cases
Column Actions
Col No. 1 Self Initial Live
Weight Dead Load
Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0
Reaction kN 231.93 1256.65 345
Elastic Rotation #.# 4.5e-4 2.61e-3 7.72e-4
Elastic Axial Shortening mm 0 0 0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 1835.21 1835.21 1662.71 1662.71 2529.28 2529.28 2007.71 2529.28
Elastic Rotation #.# -3.69e-3 -3.69e-3 -3.32e-3 -3.32e-3 -5.1e-3 -5.1e-3 -4.07e-3 -5.1e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Ultimate Flexure
kNm1 2
-2000
252 252
0
2000
4000
6000
8000
10000
12000 10193
0 13333mm
1 2
kN
3200 2368
2400
1600
800
0
-800
-1600
-2400
-3200 -2441
0 13333mm
Flexural Design
Ultimate
mm21 2
80000 0
4000
0
-4000
-8000
-12000
-16000
-20000 17648
0 13333mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
RAPT 6.6.2.0 19/3/2020 10:38:54 PM Page 9/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
kNm1 2
-3000
0
3000
6000
9000
12000
15000
18000
21000
0 13333mm
1 2
0.07
0
-0.07
-0.14
-0.21
-0.28
-0.35
0.349
-0.42
-0.49
0 13333mm
Service
Maximum Moment Condition
1 2
MPa MPa
-15 -12.34 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 320
13.53
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
MPa MPa
-15 -12.34 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 320
13.53
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.2.0 19/3/2020 10:38:55 PM Page 10/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Permanent
Maximum Moment Condition
1 2
MPa MPa
-15 -11.81 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 12.91 320
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
MPa MPa
-15 -11.81 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 12.91 320
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Characteristic Service
Maximum Moment Condition
MPa1 2MPa
-20 -13.65 -320
-15 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 320
25 15.1 400
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
MPa1 2MPa
-20 -13.65 -320
-15 -240
-10 -160
-5 -80
0 0
5 80
10 160
15 240
20 320
25 15.1 400
0 13333mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Shear Design
Beam
RAPT 6.6.2.0 19/3/2020 10:38:56 PM Page 11/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Span 1
Locat V* Mv* Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
RAPT 6.6.2.0 19/3/2020 10:38:57 PM Page 12/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Deflections
All Spans Loaded
Transfer
mm1 2
0
-2.06
-20
-40
-60
-80
6466
0 13333mm
Short Term
mm1 2
0
-20 -16
-40
-60
-80
832
0 13333mm
Incremental
mm1 2
0
-20
-18.8
-40
-60
-80
711
0 13333mm
mm1 2
0
-20
-40 -32.9
-60
-80
405
0 13333mm
Span 1
Design Comments:-
- Incremental
Detailed Span/Deflection ratio less than user defined limit = 711
Reinforcement
- Total Deflection greater than user defined limit = -32.9mm
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to
use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than
calculated. RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 7897.33mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 7904.15mm2
RAPT 6.6.2.0 19/3/2020 10:38:59 PM Page 14/14
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Reinforcement Layout
(10-T40)
1 2
mm
0
-400
15-T40
-800
14-T40
-1200
(10-T40)
(10-T40)
(10-T40)
15-T40
14-T40
-1600
0 13333mm
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to
use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than
calculated. RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 7897.33mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 7904.15mm2