Professional Documents
Culture Documents
Service Manual: LC-65D64U
Service Manual: LC-65D64U
LC-65D64U
SERVICE MANUAL
No. SY7C3LC65D64U
Revised Edition
LCD COLOR TELEVISION
MODEL LC-65D64U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
NOTE
This service manual is issued since the main and side PWBs used for LC-65D64U have been changed. For the product
where the main and side PWBs have been changed, refer to the following serial No. for each model.
Model name/Serial No. LC65D64U: 712851112~.
CONTENTS
NOTE AND MODIFIED PARTS LIST CHAPTER 4. TROUBLESHOOTING TABLE
NOTE ..................................................................i [1] TROUBLESHOOTING TABLE ......................4-1
MODIFIED PARTS LIST .....................................i
Item of modified contents ....................................i CHAPTER 5. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS .........................5-1
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRE- CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM
CAUTION ...........................................................ii [1] OVERALL WIRING DIAGRAM ......................6-1
PRECAUTIONS A PRENDRE LORS DE [2] SYSTEM BLOCK DIAGRAM .........................6-3
LA REPARATION .............................................. iii
PRECAUTIONS FOR USING LEAD-FREE CHAPTER 7. PRINTED WIRING BOARD ASSEM-
SOLDER ...........................................................iv BLIES
PRECAUTIONS IN SERVICING THE [1] MAIN Unit ......................................................7-1
HDCP-KEY ROM ..............................................iv [2] TERMINAL Unit .............................................7-9
[3] SIDE Unit..................................................... 7-11
CHAPTER 1. OPERATION MANUAL [4] R/C, LED Unit ..............................................7-13
[1] SPECIFICATIONS ......................................... 1-1 [5] KEY Unit ......................................................7-14
[2] OPERATION MANUAL .................................. 1-2
[3] DIMENSIONS ................................................ 1-8 CHAPTER 8. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
CHAPTER 2. REMOVING OF MAJOR PARTS GRAM............................................................8-1
[1] REMOVING OF MAJOR PARTS ................... 2-1 [2] SCHEMATIC DIAGRAM ................................8-2
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
NOTE
This service manual is issued since the main and side PWBs used for LC-65D64U have been changed. For the product where the main and side
PWBs have been changed, refer to the following serial No. for each model.
Model name/Serial No. LC65D64U: 712851112~.
PC compatibility chart
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 38 to set PC input signals.
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz *
31.5 kHz 60 Hz O
VGA
640 x 480 37.9 kHz 72 Hz O
37.5 kHz 75 Hz O
35.1 kHz 56 Hz O *
37.9 kHz 60 Hz O
SVGA 800 x 600
48.1 kHz 72 Hz O
PC
46.9 kHz 75 Hz O *
48.4 kHz 60 Hz O
XGA 1024 x 768 56.5 kHz 70 Hz O
60.0 kHz 75 Hz O
WXGA 1360 x 768 47.7 kHz 60 Hz O
SXGA 1280 x 1024 64.0 kHz 60 Hz O
SXGA+ 1400 x 1050 64.0 kHz 60 Hz O *
UXGA 1600 x 1200 75.0 kHz 60 Hz O
*These 4 formats are not supported by the analog RGB terminal.
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
i
LC-65D64U
LC-65D64U
SAFETY PRECAUTION Service Manual
WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. • Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing. and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
C A U T I O N : F O R C O N T I N U E D PROTECTION
reversed. (If necessary, a nonpolarized adaptor plug must be used
AGAINST A RISK OF FIRE REPLACE ONLY WITH only for the purpose of completing these checks.)
SAME TYPE FUSE.
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
F7000 (250V 6.3A)
must be corrected before returning the monitor to the owner.
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard) 1.5k ohm
Before returning the receiver to the user, perform the following 10W
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
0.15 µF
4. Inspect all protective devices such as non-metallic control knobs, TEST PROBE
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner. TO EXPOSED CONNECT TO
• Plug the AC cord directly into a 110-240 volt 50/60Hz AC outlet. METAL PARTS KNOWN EARTH
GROUND
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
LC-65D64U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
iii
LC-65D64U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
The HDCP-KEY ROM shall be protected and managed for its information inside. In servicing this ROM, therefore, take the following information pro-
tection/management measures.
1) When disposing of the component parts and PWBs, destruct the IC itself in a proper way.
(For repairing or replacing the component parts and PWBs as well as clearing those in stock)
2) In storing the component parts, protect and manage them against theft and disclosure.
(For storing the service parts, service units, etc.)
iv
LC-65D64U
CHAPTER 1. OPERATION MANUAL
LC-65D64U
Service Manual
[1] SPECIFICATIONS
1–1
LC-65D64U
[2] OPERATION MANUAL
Part names
TV (Front)
OPC indicator
SLEEP indicator
NOTE
POWER indicator
*OPC: Optical Picture Control
TV (Rear/Side)
POWER button
USB terminal
INPUT 7 terminals
(PC-IN)
AUDIO OUTPUT
INPUT 2 terminals terminals
AC INPUT terminal
1–2
LC-65D64U
Part names
1–3
LC-65D64U
Appendix
Removing the stand
Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching the stand
Before performing work make sure to turn off the TV.
1 2
Unfasten the four screws used to secure the stand in Detach the stand from the TV.
place.
NOTE
To attach the stand, perform the above steps in reverse order.
NOTE
Detach the cable clamp on the rear of the TV when using the optional mount bracket.
To use this TV mounted on a wall, remove the covers at the 4 locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
1–4
LC-65D64U
Appendix
Troubleshooting
Problem Possible Solution
Unit cannot be operated. External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning on the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
Remote control unit does not Is the FUNCTION set correctly? Set it to the TV setting position.
operate. Are batteries inserted with polarity ( + , _ ) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
The TV sometimes makes a This is not a malfunction. This happens when the cabinet slightly expands and
cracking sound. contracts according to change in temperature. This does not affect the TV's
performance.
Troubleshooting-Digital broadcasting
The error message about reception of broadcast
The example of an error message
Error code Possible Solution
displayed on a screen
No broadcast now. E203 Check the broadcast time in the program guide.
1–5
LC-65D64U
Connecting a PC
When connecting to a PC with an analog RGB terminal. (INPUT 7)
RGB cable
(commercially available)
HDMI cable
(commercially available)
PC
NOTE
• The HDMI terminals only support digital signal.
PC compatibility chart
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 38 to set PC input signals.
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz *
31.5 kHz 60 Hz O
VGA
640 x 480 37.9 kHz 72 Hz O
37.5 kHz 75 Hz O
35.1 kHz 56 Hz O *
37.9 kHz 60 Hz O
SVGA 800 x 600
48.1 kHz 72 Hz O
PC
46.9 kHz 75 Hz O *
48.4 kHz 60 Hz O
XGA 1024 x 768 56.5 kHz 70 Hz O
60.0 kHz 75 Hz O
WXGA 1360 x 768 47.7 kHz 60 Hz O
SXGA 1280 x 1024 64.0 kHz 60 Hz O
SXGA+ 1400 x 1050 64.0 kHz 60 Hz O *
UXGA 1600 x 1200 75.0 kHz 60 Hz O
*These 4 formats are not supported by the analog RGB terminal.
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
1–6
LC-65D64U
OPC OPC
Backlight Backlight
Contrast Contrast
Brightness Brightness
Color Color
Tint Tint
Sharpness Sharpness
Advanced Advanced
C.M.S.-Hue C.M.S.-Hue
C.M.S.-Saturation C.M.S.-Saturation
Color Temp. Color Temp.
Active Contrast Active Contrast
Fine Motion Fine Motion
I/P Setting I/P Setting
Film Mode Film Mode
3D-Y/C Monochrome
Monochrome Range of OPC
Range of OPC Reset
Reset
Audio Audio
Treble Treble
Bass Bass
Balance Balance
Surround Surround
Bass Enhancer Bass Enhancer
Reset Reset
Setup Setup
Option Option
Software Update
Digital Setup
1–7
LC-65D64U
[3] DIMENSIONS
3023/ 32 (780)
61/ 32 37/ 8
6011/ 64 (1528) (153) (98)
5629/ 64 (1433.5)
3711/ 64 (944)
40 (1016)
313/ 4 (806.5)
229/ 32 (566)
227/ 32
(72)
157/ 8 (403)
1721/ 64 (440)
1213/ 16 (325)
2519/ 32 (650)
1–8
LC-65D64U
CHAPTER 2. REMOVING OF MAJOR PARTS
LC-65D64U
Service Manual
1
2 Front Cabinet
Black Sheet
1
1
2 Rear Cabinet
1
2 1
1
2 3
Black Sheet
Stand
CAUTION: In the case of assembly, the new sheet (PSPAKA237WJ00 and PSPAGA386WJ00) can be stuck on these screws.
2–1
LC-65D64U
4. Remove the 4 lock screws and detach the Control Shield.
5. Remove the 8 lock screws and detach the MAIN Shield.
6. Remove the 6 lock screws and detach the AV Shield.
MAIN Shield
Control Shield 4
AV Shield
2–2
LC-65D64U
7. Disconnect all the connectors from all the PWBs.
8. Remove the Speaker (L) (R).
9. Remove the 2 lock screws, 3 lock screws and detach the Mini AV KEY Ass'y.
10.Remove the 2 lock screws, 2 lock screws and detach the Mini AV Shield, SIDE Unit, Mini AV KEY Cover from the Mini AV KEY Angle.
11.Remove the Operation Button and KEY Unit from the Mini AV KEY Cover.
Operation Button
Mini AV Shield
9
10 VD 7
LW
HM
US
7 LP/PL 7
LC-2 LC-1
LP LA
PL
10 LA-2
LW
LB
PP2
PP2 LA-1
PP3 PP3 LB
9 PD
MA
PD PP1
PE PP1
RA
HM PE
US PQ
Mini AV KEY Angle MA PQ
SP
KM
VD 7
8 8
Speaker (R) Speaker (L)
2–3
LC-65D64U
12.Remove the 8 lock screws, 1 lock screw and detach the SUB POWER Unit.
13.Remove the 5 lock screws, 2 lock screws and detach the Tray Chassis, Terminal Bottom Angle.
14.Remove the 2 lock screws and detach the Barrier Sheet.
15.Remove the 16 lock screws, 4 lock screws and detach the Inverter Shield.
Tray Chassis 13
15 15
Inverter Shield
13
Terminal Bottom Angle
15 15
Inverter Shield
12
12
Barrier Sheet
14
SUB POWER Unit
2–4
LC-65D64U
16.Remove the 2 lock screws, 4 lock Shafts and detach the Terminal Side Angle.
17.Remove the 6 lock screws and detach the POWER Unit.
18.Remove the 5 lock screws and detach the TERMINAL Unit.
19.Remove the 3 lock screws and detach the Radiator Angle.
20.Remove the 2 lock screws and detach the MAIN Unit.
17
POWER Unit
19
Radiator Angle
16
16
16 18
MAIN Unit
TERMINAL Unit
Terminal Side Angle
20
2–5
LC-65D64U
21.Remove the 2 lock screws and detach the LCD Panel Module.
22.Remove the R/C, LED Unit.
23.Remove the 12 lock screws and detach the Panel Fix Angle-B.
24.Remove the 10 lock screws and detach the Panel Fix Angle-C.
25.Remove the 12 lock screws and detach the Panel Fix Angle.
23 25 23
Panel Fix Angle
Panel Fix
Angle-C
Panel Fix
Angle-C
2–6
LC-65D64U
CHAPTER 3. ADJUSTMENT
LC-65D64U
Service Manual
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit: DUNTKE207FM01
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file SAL2Axxx.USB (named temporarily) for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
3–1
LC-65D64U
5. Even a single failure in the process will trigger the upgrade failure screen.
UPGRADE FAILURE
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
UPGRADE SUCCESS
7. Unplug the AC cord and remove the USB Memory for version upgrade.
8. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
3–2
LC-65D64U
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file SAL2VAxx.USB and SALEMxxx.BIN (named temporarily) for monitor microprocessor software version upgrade to the USB memory.
6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
UPGRADE FAILURE
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
7. Up on completion of the whole process, power and OPC LED will blink alternately. Also, the upgrade success screen will be shown if upgrade
screen was shown at 5.
UPGRADE SUCCESS
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
3–3
LC-65D64U
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL (–)” and “CH ( )” keys at a time.
(The “VOL (–)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
3–4
LC-65D64U
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
3–5
LC-65D64U
Page Line Item Description Remarks (adjustment detail, etc.)
6 [HDTV]
1 COMP33K ADJ (INPUT1) Component 33K picture level adjustment (main)
2 COMP33K ADJ (INPUT3)
3 COMP33K Y A_GAIN
4 COMP33K Cb A_GAIN
5 COMP33K Cr A_GAIN
6 COMP33K Y D_GAIN
7 COMP33K Cb D_GAIN
8 COMP33K Cr D_GAIN
9 COMP33K Y OFFSET Y OFFSET adjustment value
10 COMP33K Cb OFFSET Cb OFFSET adjustment value
11 COMP33K Cr OFFSET Cr OFFSET adjustment value
7 [ANALOG RGB]
1 ANALOG RGB ADJ Analog RGB picture level adjustment
2 R A_GAIN
3 G A_GAIN
4 B A_GAIN
5 R D_GAIN
6 G D_GAIN
7 B D_GAIN
8 R OFFSET
9 G OFFSET
10 B OFFSET
8 [M GAMMA IN]
1 LEV1 Standard value 1 Adjustment gradation setting.
2 LEV2 Standard value 2
3 LEV3 Standard value 3
4 LEV4 Standard value 4
5 LEV5 Standard value 5
6 LEV6 Standard value 6
9 [M GAMMA R1]
1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment
2 MG1G WB adjustment Point 1, G adjustment value
3 MG1B WB adjustment Point 1, B adjustment value
4 MG2R WB adjustment Point 2, R adjustment value
5 MG2G WB adjustment Point 2, G adjustment value
6 MG2B WB adjustment Point 2, B adjustment value
7 MG3R WB adjustment Point 3, R adjustment value
8 MG3G WB adjustment Point 3, G adjustment value
9 MG3B WB adjustment Point 3, B adjustment value
10 [M GAMMA R4]
1 MG4R WB adjustment Point 4, R adjustment value Parameter for six-point adjustment
2 MG4G WB adjustment Point 4, G adjustment value
3 MG4B WB adjustment Point 4, B adjustment value
4 MG5R WB adjustment Point 5, R adjustment value
5 MG5G WB adjustment Point 5, G adjustment value
6 MG5B WB adjustment Point 5, B adjustment value
7 MG6R WB adjustment Point 6, R adjustment value
8 MG6G WB adjustment Point 6, G adjustment value
9 MG6B WB adjustment Point 6, B adjustment value
11 [SOUND 1]
1 Audio Switch
2 Flat Mode
3 ADC Volume 1
4 ADC Volume 2
5 ADC Volume 3
6 ADC Volume 4
7 ADC Volume 5
8 ADC Volume 6
9 LR Fanc Vol AIN
10 LR Fanc Vol HDMI
11 LR Fanc Vol ATV
12 LR Fanc Vol DTV
13 Input Trim
3–6
LC-65D64U
Page Line Item Description Remarks (adjustment detail, etc.)
12 [SOUND 2]
1 Eala
2 Eala Bass
3 Eala D
4 Eala Surround Gain
5 Eala Bass Surround Gain
6 Eala Bass LPF Fc
7 Eala Bass LPF Gain
8 Eala Bass Treble HPF F0
9 Eala Bass Treble HPF Gain
10 Eala Bass Output Gain
11 Eala Bass Attack Time
12 Eala Bass Release Time
13 [SOUND 3]
1 Eala D Surround Width
2 Eala D Bass Enhancer
3 Eala D Dialogue Boost
4 Eala D Bass Doubler
5 Eala D F0
6 Eala D DRC Ratio
7 Eala D DRC Threshold Level
14 [SOUND 4]
1 EQ_MODE
2 PEQ1_F0
3 PEQ1_Q
4 PEQ1_GAIN
5 PEQ2_F0
6 PEQ2_Q
7 PEQ2_GAIN
8 PEQ3_F0
9 PEQ3_Q
10 PEQ3_GAIN
15 [SOUND 5]
1 PEQ4_F0
2 PEQ4_Q
3 PEQ4_GAIN
4 PEQ5_F0
5 PEQ5_Q
6 PEQ5_GAIN
7 PEQ6_F0
8 PEQ6_Q
9 PEQ6_GAIN
10 PEQ7_F0
11 PEQ7_Q
12 PEQ7_GAIN
16 [SOUND 6]
1 Output Trim
2 Clipper Level
3 Sub Vol Default
4 Sub Vol Eala
5 Sub Vol Eala Bass
6 Sub Vol Eala D
7 Sub Vol Eala Bass D
8 SW Fanc Vol AIN
9 SW Fanc Vol HDMI
10 SW Fanc Vol ATV
11 SW Fanc Vol DTV
3–7
LC-65D64U
Page Line Item Description Remarks (adjustment detail, etc.)
17 [SOUND 7]
1 BE ATT
2 BASS VOL0 MIN
3 BASS VOL0 CENTER
4 BASS VOL0 MAX
5 BASS VOL60 MIN
6 BASS VOL60 CENTER
7 BASS VOL60 MAX
8 BASS CENTER ATT
18 [SOUND 8]
1 TREBLE VOL0 MIN
2 TREBLE VOL0 CENTER
3 TREBLE VOL0 MAX
4 TREBLE VOL60 MIN
5 TREBLE VOL60 CENTER
6 TREBLE VOL60 MAX
7 TREBLE CENTER ATT
19 [M PWM]
1 PANNEL SELECT
2 PWM
3 PWN FREQ
4 PWM DUTY
5 OSC FREQ
6 OSC DUTY
20 [M BRI DA1]
1 BRIGHTNESS DA0
2 BRIGHTNESS DA1
3 BRIGHTNESS DA2
4 BRIGHTNESS DA3
5 BRIGHTNESS DA4
6 BRIGHTNESS DA5
7 BRIGHTNESS DA6
8 BRIGHTNESS DA7
9 BRIGHTNESS DA8
10 BRIGHTNESS DA9
11 BRIGHTNESS DA10
12 BRIGHTNESS DA11
21 [M BRI DA2]
1 BRIGHTNESS DA12
2 BRIGHTNESS DA13
3 BRIGHTNESS DA14
4 BRIGHTNESS DA15
5 BRIGHTNESS DA16
6 BRIGHTNESS DA17
7 BRIGHTNESS DA18
8 BRIGHTNESS DA19
9 BRIGHTNESS DA20
10 BRIGHTNESS DA21
11 BRIGHTNESS DA22
22 [M BRI DA3]
1 BRIGHTNESS DA23
2 BRIGHTNESS DA24
3 BRIGHTNESS DA25
4 BRIGHTNESS DA26
5 BRIGHTNESS DA27
6 BRIGHTNESS DA28
7 BRIGHTNESS DA29
8 BRIGHTNESS DA30
9 BRIGHTNESS DA31
10 BRIGHTNESS DA32
3–8
LC-65D64U
Page Line Item Description Remarks (adjustment detail, etc.)
23 [M ADL1]
1 OPC33 ADLEVEL 0
2 OPC33 ADLEVEL 1
3 OPC33 ADLEVEL 2
4 OPC33 ADLEVEL 3
5 OPC33 ADLEVEL 4
6 OPC33 ADLEVEL 5
7 OPC33 ADLEVEL 6
8 OPC33 ADLEVEL 7
9 OPC33 ADLEVEL 8
10 OPC33 ADLEVEL 9
11 OPC33 ADLEVEL 10
12 OPC33 ADLEVEL 11
24 [M ADL2]
1 OPC33 ADLEVEL 12
2 OPC33 ADLEVEL 13
3 OPC33 ADLEVEL 14
4 OPC33 ADLEVEL 15
5 OPC33 ADLEVEL 16
6 OPC33 ADLEVEL 17
7 OPC33 ADLEVEL 18
8 OPC33 ADLEVEL 19
9 OPC33 ADLEVEL 20
10 OPC33 ADLEVEL 21
11 OPC33 ADLEVEL 22
25 [M ADL3]
1 OPC33 ADLEVEL 23
2 OPC33 ADLEVEL 24
3 OPC33 ADLEVEL 25
4 OPC33 ADLEVEL 26
5 OPC33 ADLEVEL 27
6 OPC33 ADLEVEL 28
7 OPC33 ADLEVEL 29
8 OPC33 ADLEVEL 30
9 OPC33 ADLEVEL 31
26 [M V6THE]
1 V6 OS THERMO 1
2 V6 OS THERMO 2
3 V6 OS THERMO 3
4 V6 OS THERMO 4
5 V6 OS THERMO 5
6 V6 OS THERMO 6
7 V6 OS THERMO 7
27 [M V5THE]
1 V5 OS THERMO 1
2 V5 OS THERMO 2
3 V5 OS THERMO 3
4 V5 OS THERMO 4
5 V5 OS THERMO 5
6 V5 OS THERMO 6
7 V5 OS THERMO 7
28 [M TEMP]
1 BL TEMP1
2 BL TEMP2
3 BL TDUTY
29 [M EEP SET]
1 MONITOR TIME OUT
2 MONITOR MAX TEMP
3 MONITOR ERROR CAUSE
RESET
30 [M TESTPTRN]
1 LCD TEST PATTERN
2 TV TEST PATTERN 1
3 TV TEST PATTERN 2
3–9
LC-65D64U
Page Line Item Description Remarks (adjustment detail, etc.)
31 [MEMORY CLR]
1 KEY LOCK (1217)
2 KOUTEI AREA ALL CLEAR
3 A MODE AREA CLEAR
4 BACKUP AREA CLEAR
5 B MODE AREA CLEAR
6 EXECUTION
32 [ETC]
1 EEP SAVE Writing setting values to EEPROM.
2 EEP RECOVER Reading setting values from EEPROM.
3 STANDBY CAUSE RESET Reset stand by cause.
4 SETTING FOR ADJ
6. Special features
* STANDBY CAUSE (Page 1/32)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 32/32)
Storage of EEP adjustment value
* EEP RECOVER (Page 32/32)
Retrieval of EEP adjustment value from storage area
3 – 10
LC-65D64U
7.3. N358 composite signal adjustment (Tuner)
2 Auto adjustment Page 3/32 Bring the cursor on [•N358 ALL ADJ] and press [ENTER].
performance [•N358 ALL ADJ FINISH] appears when finished.
100% white
2 Auto adjustment Page 5/32 Bring the cursor on [•COMP 15K ADJ] and press [ENTER].
performance [•COMP 15K ADJ FINISH] appears when finished.
100% white
2 Auto adjustment Page 6/32 Bring the cursor on [•COMP 33K ADJ] and press [ENTER].
performance [•COMP 33K ADJ FINISH] appears when finished.
2 Auto adjustment Bring the cursor on [•ANALOG RGB ADJ] and press [ENTER].
performance [•ANALOG RGB ADJ OK] appears when finished.
3 – 11
LC-65D64U
8. Adjustment of white balance
8.1. White balance adjustment
Point 1
WBI10176
MG1G****
MG1B****
MG1R****
Writing
MSET0003
3 – 12
LC-65D64U
8.2. Adjusting procedure by use of [RS-232C]
1. Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2. Start the unit with the RS-232C cable connected.
3. Start the terminal software. (The freeware readily available on the Internet will do.)
4. Make the following settings.
5. If the settings are correct, the terminal software indicates “ERR” against pressing of the “ENTER” key.
6. After the settings are done correctly, it is possible to make an adjustment by typing in the command shown in the table below and pressing the
“ENTER” key on the keyboard.
7. Command entry is successful if the terminal software indicates “OK” when the “ENTER” is pressed. If “ERR” is shown, retry to enter the command.
8. Send the process mode switching command to switch from the RS232C operation mode to the process mode.
KRSW0001: “ERR” is returned.
KKT10037: When “OK” is returned, the process mode becomes active. When “ERR”, start over from KRSW0001.
9. Send each adjustment command.
3 – 13
LC-65D64U
10. Model number ID plug
Model numbers are identified by inserting the destination ID plug (QCNCMA275WJQZ) in its specified slot of the destination ID connector SC9201/
SC9202 (QCNCWA715WJQZY).
㪛㪼㫊㫋㫀㫅㪸㫋㫀㫆㫅㩷㪠㪛㩷㪺㫆㫅㫅㪼㪺㫋㫆㫉㩷㫃㫆㪺㪸㫋㫀㫆㫅㫊
㪋㪈 㪈 㪈 㪉㪇 㪈 㪋
䇼㪣㪮䇽 䇼㪣㪧䇽 䇼㪣㪙䇽 㪪㪚㪐㪉㪇㪈 㪪㪚㪐㪉㪇㪉
㪣㪚㪄㪍㪌㪛㪍㪋㪬 㽸 㽲
㪪㪚㪐㪉㪇㪉
㪩㪪㪄㪉㪊㪉㪚 㪧㫃㫌㪾㩷㫃㫆㪺㪸㫋㫀㫆㫅㫊
㽲 㽴 㽶 㽸 㽹
㪈
㪛㪄㫊㫌㪹㩷㪘㫌㪻㫀㫆
㪙㪚㪤㪊㪌㪌㪊 㽳 㽵 㽷
䇼㪧㪛䇽 㪈㪉
㪛㪄㫊㫌㪹
㪤㪘㪠㪥
㪪㪚㪐㪉㪇㪈
㪜㪌㪌㪏
㪟㪛㪤㪠㩷㪘㫌㪻㫀㫆
㪟㪛㪤㪠
䇼㪟㪤䇽 㪉
㪟㪛㪤㪠 䇼㪩㪘䇽
㪈 㪉㪈
㪈 㪈㪌 䇼㪤㪘䇽
䇼㪬㪪䇽 䇼㪢㪤䇽
㪦㫇㫋㫀㪺㪸㫃㩷㪦㫌㫋㫇㫌㫋 㪈 㪈㪋 㪈 㪋 㪏㪇 㪛㪼㫊㫋㫀㫅㪸㫋㫀㫆㫅㩷㪠㪛㩷㪺㫆㫅㫅㪼㪺㫋㫆㫉 㪛㪼㫊㫋㫀㫅㪸㫋㫀㫆㫅㩷㪠㪛㩷㫇㫃㫌㪾
䋨㪨㪚㪥㪚㪮㪘㪎㪈㪌㪮㪡㪨㪱㪰䋩 䋨㪨㪚㪥㪚㪤㪘㪉㪎㪌㪮㪡㪨㪱䋩
3 – 14
LC65D64U
CHAPTER 4. TROUBLESHOOTING TABLE
LC65D64U
Service Manual
COMPOSITE: No external input video COMPOSITE: No external input video COMPOSITE: No external input video
[INPUT-1] [INPUT-2] [INPUT-3]
Is INPUT-1 selected on the input select Is INPUT-2 selected on the input select menu Is INPUT-3 selected on the input select
menu screen? screen? menu screen?
NO NO NO
Select INPUT-1 on the input Select INPUT-2 on the input Select INPUT-3 on the input
select menu screen for the right select menu screen for the right select menu screen for the right
input signal. input signal. input signal.
Does the INPUT-1 V3_PLUG Does the INPUT-2 V2_PLUG Does the INPUT-1 V1_PLUG
detection function? detection function? detection function?
Check the line between pin (7) Check the line between pin (7) of Check the line between pin (7)
of input terminal (J501) and pin input terminal (J503) and pin (35) of input terminal (J901) and pin
(37) of IC501 (AV_SW). of IC501 (AV_SW). (33) of IC501 (AV_SW).
J901 pin (7) P901 pin (7)
YES YES YES
P501 pin (7) IC501 pin
(33)
Is there the COMPOSITE signal input at pin Is there the COMPOSITE video signal input at Is there the COMPOSITE signal input at
(38) of IC501 (AV_SW)? pin (36) of IC501 (AV_SWITCH)? pin(34) of IC501(AV_SW)?
NO NO NO
Check the line between pin (6) Check the line between pin (6) of Check the line between pin (6)
of J501 and pin (38) of IC501. J503 and pin (36) of IC501. of J901 and pin (34) of IC501.
J901 pin (6) P901 pin (5)
P501 pin (5) IC501 pin
YES YES YES
(34)
Is there the COMPOSITE video signal output at pin(30) of IC501? NO Check IC501 and its peripheral
circuits.
YES
Is there the COMPOSITE video signal output at pin(59) of connector(SC501) on the TERMINAL NO Check the line between IC501
unit? and SC501 (Q501 and Q502,
etc.).
YES
Is there the COMPOSITE video signal input at pin(59) of connector(SC2203) on the MAIN unit? NO Check the line between SC501
and SC2203 connectors.
YES
Is there the COMPOSITE signal input at pin(AN16) of IC8001(CPU)? NO Check the line between SC2203
and IC8001 (Q2216, etc.).
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? Check IC8001 and its peripheral
LVDS_TX_0_DATA0_P/N(C7/B7), LVDS_TX_0_DATA1_P/N(E7/D7), LVDS_TX_0_DATA2_P/N(C6/ circuits.(IC8151 thru IC8154,
B6), LVDS_TX_0_DATA3_P/N(C5/B5), LVDS_TX_0_DATA4_P/N(E5/D5), LVDS_TX_0_CLK_P/ NO etc.)
N(E6/D6),
LVDS_TX_1_DATA0_P/N(B4/A4), LVDS_TX_1_DATA1_P/N(E4/D4), LVDS_TX_1_DATA2_P/N(B3/
A3), LVDS_TX_1_DATA3_P/N(B1/B2), LVDS_TX_1_DATA4_P/N(F5/F6), LVDS_TX_1_CLK_P/
N(C2/C3),
YES
Check the panel module.
4–1
LC65D64U
No video (2)
COMPONENT: No external input video [INPUT-1] COMPONENT: No external input video [INPUT-3]
Is INPUT-1 selected on the input select menu screen? Is INPUT-3 selected on the input select menu screen?
Is the INPUT-SELECT for the input signal? Is the INPUT-SELECT for the input signal?
NO NO
Select INPUT-1 on the input select menu screen for the Select INPUT-3 on the input select menu screen for the
right input signal. right input signal.
Does the INPUT-1 C2_PLUG detection function? Does the INPUT-3 C1_PLUG detection function?
Check the line between pin (7) of input terminal (J502) and Check the line between pin (7) of input terminal (J902) and
pin (58) of IC501 (AV_SW). pin (50) of IC501 (AV_SW).
J902 pin(7) P901 pin (15)
YES YES
P501 pin (15) IC501 pin (50)
Are there the COMPONENT video signal inputs at pins(59)(Y)/ Are there the COMPONENT video signal inputs at pins(51)(Y)/(53)(Pb)
(60)(Pb) and (61)(Pr) of IC501(AV_SW)? and (55)(Pr) of IC501(AV_SW)?
NO NO
Check the line between the input terminals of J502 and Check the line between the input terminals of J902 and
IC501. IC501.
J502 pin (6) (Y) pin (5) (Pb) pin (4) (Pr) J902 pin (6) (Y) pin (5) (Pb) pin (4) (Pr)
IC501 pin (59) pin (60) pin (61) P901 pin (13) pin (11) pin (9)
P501 pin (13) pin (11) pin (9)
YES
YES IC501 pin (51) pin (53) pin (55)
Are there the COMPONENT video signal outputs at pins (30) (Y)/(28) NO Check IC501 and its peripheral circuits.
(Pb) and (27) (Pr) of IC501?
YES
Are there the COMPONENT video signal outputs at pins (59), (57) and NO Check the line between IC501 and SC501 (Q501 thru
(55) of connector (SC501) on the TERMINAL unit? Q506, etc.).
YES
Are there the COMPONENT video signal inputs at pins (59), (57) and NO Check the line between SC501 and SC2203 connectors.
(55) of connector (SC2203) on the MAIN unit?
YES
Are there the COMPONENT video signal inputs at pins (AM21) (Y)/ NO Check the line between the connector of SC2203 and
(AN21) (Pb) and (AL21) (Pr) of IC8001 (CPU)? IC8001 (Q2202, Q2203 and Q2206, etc.).
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel NO Check IC8001 and its peripheral circuits. (IC8151 thru
of IC8001? IC8154, etc.)
LVDS_TX_0_DATA0_P/N(C7/B7), LVDS_TX_0_DATA1_P/N(E7/D7),
LVDS_TX_0_DATA2_P/N(C6/B6), LVDS_TX_0_DATA3_P/N(C5/B5),
LVDS_TX_0_DATA4_P/N(E5/D5), LVDS_TX_0_CLK_P/N(E6/D6),
LVDS_TX_1_DATA0_P/N(B4/A4), LVDS_TX_1_DATA1_P/N(E4/D4),
LVDS_TX_1_DATA2_P/N(B3/A3), LVDS_TX_1_DATA3_P/N(B1/B2),
LVDS_TX_1_DATA4_P/N(F5/F6), LVDS_TX_1_CLK_P/N(C2/C3),
YES
Check the panel module.
4–2
LC65D64U
No video (3)
NO
Does the INPUT-2 S1_PLUG
detection function?
Check the line between pin (6) of
input terminal (J504) and pin (41)
of IC501 (AV_SW).
YES
Are there the S-VIDEO signal inputs at pins (42) (Y) and (44) (C) of
IC501 (AV_SW)?
NO
Check the line between pins (3)
(Y)/(4) (C) of J504 and pins (42)/
(44) of IC501.
YES
Are there the S-VIDEO signal outputs at pins (59) (Y) and (57) (C) of NO Check the line between IC501 and SC501 (Q501 thru Q504,
connector (SC501) on the TERMINAL unit? etc.).
YES
Are there the S-VIDEO signal inputs at pins (59) (Y) and (57) (C) of NO Check the line between SC501 and SC2203 connectors.
connector (SC2203) on the MAIN unit?
YES
Are there the S-VIDEO signal inputs at pins (AL17) (Y) and (AL16) (C) NO Check the line between SC2203 and IC8001 (Q2201 and
of IC8001 (CPU)? Q2205, etc.).
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel Check IC8001 and its peripheral circuits. (IC8151 thru IC8154,
of IC8001? etc.)
LVDS_TX_0_DATA0_P/N (C7/B7), LVDS_TX_0_DATA1_P/N (E7/D7),
LVDS_TX_0_DATA2_P/N (C6/B6), LVDS_TX_0_DATA3_P/N (C5/B5), NO
LVDS_TX_0_DATA4_P/N (E5/D5), LVDS_TX_0_CLK_P/N (E6/D6),
LVDS_TX_1_DATA0_P/N (B4/A4), LVDS_TX_1_DATA1_P/N (E4/D4),
LVDS_TX_1_DATA2_P/N (B3/A3), LVDS_TX_1_DATA3_P/N (B1/B2),
LVDS_TX_1_DATA4_P/N (F5/F6), LVDS_TX_1_CLK_P/N (C2/C3)
YES
Check the panel module.
4–3
LC65D64U
No video (4)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Is there the analog video signal output (VIDEO) at pin(13) of Are there the video signal outputs (IF_OUT_P/N) at the pins(19) and
tuner(TU1101)? (20) of tuner(TU1101)?
NO NO
Check TU1101 and its peripheral Check TU1101 and its peripheral
circuits (SDA/SCL_3_5, etc.). circuits (SDA/SCL_3_5, etc.).
YES YES
Is there the analog video signal output at pin (61) of connector Are there the video signal outputs at pins (72) and (70) of connector
(SC501) on the TERMINAL unit? (SC501) on the TERMINAL unit?
NO NO
Check the line between TU1101 Check the line between TU1101
and SC501 (Q510, etc.). and SC501.
YES YES
Is there the analog video signal input at pin (61) of connector Are there the video signal inputs at pins (72) and (70) of connector
(SC2203) on the MAIN unit? (SC2203) on the MAIN unit?
NO NO
Check the line between SC2203 Check the line between SC2203
and SC501 connectors. and SC501 connectors.
YES
YES
Is there the analog video signal input at pin (AM19) of IC8001 (CPU)? Are there the video signal inputs at pin (AM33) and (AM34) of IC8001
(CPU)?
NO NO
Check the line between IC8001 Check the line between IC8001
and SC2203 (Q2214, etc.). and SC2203 (L2204, C2229,
YES etc.).
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001?
LVDS_TX_0_DATA0_P/N (C7/B7), LVDS_TX_0_DATA1_P/N (E7/D7), LVDS_TX_0_DATA2_P/N (C6/B6), LVDS_TX_0_DATA3_P/N (C5/B5),
LVDS_TX_0_DATA4_P/N (E5/D5), LVDS_TX_0_CLK_P/N(E6/D6),
LVDS_TX_1_DATA0_P/N (B4/A4), LVDS_TX_1_DATA1_P/N (E4/D4), LVDS_TX_1_DATA2_P/N (B3/A3), LVDS_TX_1_DATA3_P/N (B1/B2),
LVDS_TX_1_DATA4_P/N (F5/F6), LVDS_TX_1_CLK_P/N (C2/C3)
YES NO
Check the panel module. Check IC8001 and its peripheral
circuits. (IC8151 thru IC8154,
etc.)
4–4
LC65D64U
HDMI: No external input video [INPUT-4] HDMI: No external input video [INPUT-5]
Is INPUT-4 selected on the input select menu screen? Is INPUT-5 selected on the input select menu screen?
NO NO
Select INPUT-4 on the input select menu screen for Select INPUT-5 on the input select menu screen for the
the right input signal. right input signal.
Does the HOT PLUG detection function? Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC801 Does the DDC5V signal come from pin (18) of SC1601
to pin (72) of IC1604 (HDMI-SW)? to pin (32) of IC1604 (HDMI-SW)?
NO NO
Check the line between the input termi- Check the line between the input terminals
nals of SC801 and IC1604. of SC1601 and IC1604.
SC801 pin(18) IC801 pin(39)
SC802 pin(19) SC1603 pin(3)
IC1604 pin(72)
YES YES
Does the HPD signal come from pin (56) of IC1604 to Does the HPD signal come from pin (16) of IC1604 to
pin (19) of SC801? pin (19) of SC1601?
YES YES
NO NO
Check the line between IC1604 and Check the line between IC1604 and
SC801. SC1601.
IC1604 pin(56) SC1603 pin(4) IC1604 pin(16) IC1607 pin(4)
SC802 pin(18) IC801 pin(25) SC1601 pin(19)
IC807 pin(4) SC801 pin(19)
Are there the TMDS signal inputs at pins (27/28) (CLK-/+), (29/30) (D0-/ Are there the TMDS signal inputs at pins (18/19) (CLK-/+), (21/22)
+), (32/33) (D1-/+), (34/35) (D2-/+), all of IC803? (D0-/+), (24/25) (D1-/+), (27/28) (D2-/+), all of IC1604?
NO NO
Is IC802 (EEPROM) accessed by I2C, with HDMI Is IC1601 (EEPROM) accessed by I2C, with HDMI con-
connected, to read the DDC_I2C SCL/SDA data? nected, to read the DDC_I2C SCL/SDA data?
NO NO
Check the DDC line and its peripheral circuits. (IC801 Check the DDC line and its peripheral circuits. (IC1601
YES and its peripherals). and its peripherals).
Are there the TMDS signal inputs at pins (58/59) (CLK-/+), (61/62) (D0-/
+), (64/65) (D1-/+), (67/68) (D2-/+), all of IC1604?
NO
Check the TMDS line between IC803 and IC1604
(SC802 and SC1603, etc.).
YES YES
Are there the TMDS signal inputs at pins (AM1/AM2) (CLK-/+), (AN1/AN2) (D0-/+), (AM3/ NO Check IC1604, IC8001 and their peripheral
AM4) (D1-/+), (AP2/AN3) (D2-/+), all of IC8001 (CPU)? circuits.
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C7/B7), LVDS_TX_0_DATA1_P/N (E7/D7), (IC8151 thru IC8154, etc.)
LVDS_TX_0_DATA2_P/N (C6/B6), LVDS_TX_0_DATA3_P/N (C5/B5),
LVDS_TX_0_DATA4_P/N (E5/D5), LVDS_TX_0_CLK_P/N (E6/D6), Is IC8451 (EEPROM for HDCP) accessed
LVDS_TX_1_DATA0_P/N (B4/A4), LVDS_TX_1_DATA1_P/N (E4/D4), by I2C (SCL2/SDA2) to read HDCP data?
LVDS_TX_1_DATA2_P/N (B3/A3), LVDS_TX_1_DATA3_P/N (B1/B2), Check IC8451 and its peripheral circuits.
LVDS_TX_1_DATA4_P/N (F5/F6), LVDS_TX_1_CLK_P/N (C2/C3),
YES
Check the panel module.
4–5
LC65D64U
NO
Select INPUT-6 on the input select menu screen for the right input
signal.
NO
Check the line between the input terminals of
SC1602 and IC1604.
YES
Does the HPD signal come from pin (36) of IC1604 to pin (19) of
SC1602?
NO
Check the line between IC1604 and SC1602.
IC1604 pin (36) IC1608 pin (4)
SC1602 pin (19)
YES
Are there the TMDS signal inputs at pins (38/39) (CLK-/+), (41/42) (D0-/+), (44/45)
(D1-/+), (47/48) (D2-/+), all of IC1604?
NO
Is IC1603 (EEPROM) accessed by I2C, with HDMI connected, to
read the DDC_I2C SCL/SDA data?
NO
Check the DDC line and its peripheral circuits. (IC1603 and its
peripherals).
YES
Are there the TMDS signal inputs at pins (AM1/AM2) (CLK-/+), (AN1/AN2) (D0-/+), NO Check IC1604, IC8001 and their peripheral circuits.
(AM3/AM4) (D1-/+), (AP2/AN3) (D2-/+), all of IC8001 (CPU)?
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits. (IC8151 thru
LVDS_TX_0_DATA0_P/N (C7/B7), LVDS_TX_0_DATA1_P/N (E7/D7), IC8154, etc.)
LVDS_TX_0_DATA2_P/N (C6/B6), LVDS_TX_0_DATA3_P/N (C5/B5),
LVDS_TX_0_DATA4_P/N (E5/D5), LVDS_TX_0_CLK_P/N (E6/D6), Is IC8451 (EEPROM for HDCP) accessed by I2C
LVDS_TX_1_DATA0_P/N (B4/A4), LVDS_TX_1_DATA1_P/N(E4/D4), (SCL2/SDA2) to read HDCP data? Check IC8451
LVDS_TX_1_DATA2_P/N (B3/A3), LVDS_TX_1_DATA3_P/N (B1/B2), and its peripheral circuits.
LVDS_TX_1_DATA4_P/N (F5/F6), LVDS_TX_1_CLK_P/N (C2/C3)
YES
Check the panel module.
4–6
LC65D64U
No video (6)
NO
Select INPUT-7 on the input select menu screen for the right input
signal.
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? Check IC8001 and its peripheral circuits. (IC8151
LVDS_TX_0_DATA0_P/N (C7/B7), LVDS_TX_0_DATA1_P/N (E7/D7), thru IC8154, etc.)
LVDS_TX_0_DATA2_P/N (C6/B6), LVDS_TX_0_DATA3_P/N (C5/B5), NO
LVDS_TX_0_DATA4_P/N (E5/D5), LVDS_TX_0_CLK_P/N (E6/D6),
LVDS_TX_1_DATA0_P/N (B4/A4), LVDS_TX_1_DATA1_P/N (E4/D4),
LVDS_TX_1_DATA2_P/N (B3/A3), LVDS_TX_1_DATA3_P/N (B1/B2),
LVDS_TX_1_DATA4_P/N (F5/F6), LVDS_TX_1_CLK_P/N (C2/C3),
YES
Check the panel module.
4–7
LC65D64U
No audio (1)
Is INPUT-1 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” Is the audio output selected for “VARIABLE” on
on the menu screen? the menu screen?
YES Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES
Does the audio signal come from pins (4) (L) and (5) (R) Does the audio signal come from pins (4) (L) and (5) (R) of
of input terminal (J501) to pins (8) (L) and (13) (R) of input terminal(J503) to pins (7) (L) and (12) (R) of IC501
IC501 (AV_SW) on the TERMINAL unit? (AV_SW) on the TERMINAL unit?
NO NO
Check the line between J501 and IC501. YES Check the line between J503 and IC501.
YES
Does the audio signal come from pins (20) (L) and (18) (R) of IC501 to pins (51) (L) and (53) (R) of connector (SC501)?
NO
Check the line between IC501 and SC501 its
peripheral circuits.
YES
Are there the audio signal inputs at pins (51) (L) and (53) (R) of connector NO Check the line between SC501 and SC2203.
(SC2203) on the MAIN unit?
YES
Does the audio signal come from pins (51) (L) and (53) (R) of SC2203 to pins (35) NO Check the line between IC1403 and SC2203.
(L) and (36) (R) of IC1403 (CODEC)?
YES
Does the audio signal come from pins (4) (COD_LRCK), (5) (COD_BCK) and (6) NO Check the line between IC1403 and IC8001.
(COD_SDOUT) of IC1403 to pins (AK24), (AH24) and (AJ24) of IC8001 (CPU)?
YES
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) NO Check the line between IC8001 and IC1402.
(DSP_BCKIN), (AL25) (DSP_SDIN1) and (L32) (DSP_SDIN2) of IC8001 to pins
(2), (3), (6) and (4) of IC1402 (SOUND_DSP)?
YES
Does the audio signal come from pins (19) (DSP_SDOUT1) and (21) NO Check the line between IC1402 and IC1403.
(DSP_SDOUT3) of IC1402 to pins (11) and (12) of IC1403 (CODEC)?
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) (DSP_BCKIN) NO Check the line between IC8001 and IC1403.
and (AL24) (DSP_MCLK) of IC8001 to pins (8), (9) and (10) of IC1403?
YES
Does the audio signal come from pins (17) (SPOUT_LP) and (18) (SPOUT_RP) of NO Check the line between SC2203 and
IC1403 to pins (21) (SP_LP) and (25) (SP_RP) of connector(SC2203) on the MAIN IC1403(D1305, D1312, Q1306 and Q1307,
unit? etc.).
YES
Are there the audio signal inputs at pins (21) (SP_LP) and (25) (SP_RP) of con- NO Check the line between SC501 and SC2203.
nector (SC501) on the TERMINAL unit?
YES
Does the audio signal come from pins (21) (SP_LP) and (25) (SP_RP) of SC501 to NO Check the line between SC501 and IC2701,
pins (5) (SP_LP) and (9) (SP_RP) of IC2701 (AMP) on the TERMINAL unit? and their peripheral circuits (AMP_MUTE line,
etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
4–8
LC65D64U
No audio (1)
INPUT-3 No audio
Is INPUT-3 selected on the input select menu screen? Is the audio output selected for “VARIABLE” on the menu
NO screen?
YES Set the audio output to “FIXED”.
Does the audio signal come from pins (5) (L) and (4) (R) of input Check the line between J901 and P901, and their peripheral cir-
terminal (J901) to pins (3) (L) and (1) (R) of P901 on the SIDE NO cuits.
unit?
YES
Are there the audio signal inputs at pins (3) (L) and (1) (R) of Check the line between P501 and P901.
P501 on the TERMINAL unit? NO
YES
Does the audio signal come from pins (3) (L) and (1) (R) of P501 Check the line between P501 and IC501, and their peripheral cir-
to pins (6) and (11) of IC501 on the TERMINAL unit? NO cuits.
YES
Does the audio signal come from pins (20) (L) and (18) (R) of Check the line between IC501 and SC501 its peripheral circuits.
IC501 to pins (51) (L) and (53) (R) of connector (SC501)? NO
YES
Are there the audio signal inputs at pins(51)(L) and (53)(R) of Check the line between SC501 and SC2203.
connector(SC2203) on the MAIN unit? NO
YES
Does the audio signal come from pins (51) (L) and (53) (R) of Check the line between IC1403 and SC2203.
SC2203 to pins (35) (L) and (36) (R) of IC1403 (CODEC)? NO
YES
Does the audio signal come from pins (4) (COD_LRCK), (5) Check the line between IC1403 and IC8001.
(COD_BCK) and (6) (COD_SDOUT) of IC1403 to pins (AK24), NO
(AH24) and (AJ24) of IC8001 (CPU)?
YES
Does the audio signal come from pins (AJ25) (DSP_LRCK), Check the line between IC8001 and IC1402.
(AK25) (DSP_BCKIN), (AL25) (DSP_SDIN1) and (L32)
(DSP_SDIN2) of IC8001 to pins (2), (3), (6) and (4) of IC1402 NO
(SOUND_DSP)?
YES
Does the audio signal come from pins (19) (DSP_SDOUT1) and Check the line between IC1402 and IC1403.
(21) (DSP_SDOUT3) of IC1402 to pins (11) and (12) of IC1403 NO
(CODEC)?
Does the audio signal come from pins (AJ25) (DSP_LRCK), Check the line between IC8001 and IC1403.
(AK25) (DSP_BCKIN) and (AL24) (DSP_MCLK) of IC8001 to NO
pins (8), (9) and (10) of IC1403?
YES
Does the audio signal come from pins (17) (SPOUT_LP) and (18) Check the line between SC2203 and IC1403(D1305, D1312,
(SPOUT_RP) of IC1403 to pins (21) (SP_LP) and (25) (SP_RP) NO Q1306 and Q1307, etc.).
of connector (SC2203) on the MAIN unit?
YES
Are there the audio signal inputs at pins (21) (SP_LP) and (25) Check the line between SC501 and SC2203.
(SP_RP) of connector (SC501) on the TERMINAL unit? NO
YES
Does the audio signal come from pins (21) (SP_LP) and (25) Check the line between SC501 and IC2701, and their peripheral
(SP_RP) of SC501 to pins (5) (SP_LP) and (9) (SP_RP) of NO circuits (AMP_MUTE line, etc.).
IC2701 (AMP) on the TERMINAL unit?
YES
Is the audio output from IC2701 as specified? Check IC2701 and its peripheral circuits.
NO
YES
Check the connector (P2701), speakers and their peripheral cir-
cuits.
4–9
LC65D64U
No audio (2)
[HDMI analog audio input] INPUT-6 No audio [PC analog audio input] INPUT-7 No audio
Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” on the Is the audio output selected for “VARIABLE” on the
menu screen? menu screen?
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Does the audio signal come from pins (4) (L) and (2) (R) of input termi- Does the audio signal come from pins (2) (L) and (3) (R) of input
nal (J1601) to pins (43) (L) and (44) (R) of IC1403 (CODEC) on the terminal (J2201) to pins (46) (L) and (47) (R) of IC1403 (CODEC)
MAIN unit? on the MAIN unit?
NO NO
Check the line between J1601 and IC1403, and their Check the line between J2201 and IC1403, and their
peripheral circuits. peripheral circuits.
YES YES
Does the audio signal come from pins (4) (COD_LRCK), (5) (COD_BCK) and (6) (COD_SDOUT) of IC1403 to pins (AK24), (AH24) and (AJ24) of
IC8001 (CPU)?
NO
Check the line between IC1403 and IC8001.
YES
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) NO Check the line between IC8001 and IC1402.
(DSP_BCKIN), (AL25) (DSP_SDIN1) and (L32) (DSP_SDIN2) of IC8001 to
pins (2), (3), (6) and (4) of IC1402 (SOUND_DSP)?
YES
Does the audio signal come from pins (19) (DSP_SDOUT1) and (21) NO Check the line between IC1402 and IC1403.
(DSP_SDOUT3) of IC1402 to pins (11) and (12) of IC1403 (CODEC)?
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) NO Check the line between IC8001 and IC1403.
(DSP_BCKIN) and (AL24) (DSP_MCLK) of IC8001 to pins (8), (9) and (10) of
IC1403?
YES
Does the audio signal come from pins (17) (SP_LP) and (18) (SP_RP) of NO Check the line between SC2203 and IC1403 (Q1313,
IC1403 to pins (21) (SP_LP) and (25) (SP_RP) of connector(SC2203) on the Q1314, etc.).
MAIN unit?
YES
Are there the audio signal inputs at pins (21) (SP_LP) and (25) (SP_RP) of con- NO Check the line between SC501 and SC2203.
nector (SC501) on the TERMINAL unit?
YES
Does the audio signal come from pins (21) (SP_LP) and (25) (SP_RP) of NO Check the line between SC501 and IC2701, and their
SC501 to pins (5) (SP_LP) and (9)(SP_RP) of IC2701(AMP) on the TERMINAL peripheral circuits (AMP_MUTE line, etc.).
unit?
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
4 – 10
LC65D64U
No audio (3)
No audio at UHF/VHF broadcast signal reception No audio at digital broadcast signal reception
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” on the menu Is the audio output selected for “VARIABLE” on the
screen? menu screen?
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is there the SIF signal output at pin (15) of tuner (TU1101) on the TER- Are there the video signal outputs (IF_OUT_P/N) at the pins (19)
MINAL unit? and (20) of tuner (TU1101) on the TERMINAL unit?
NO NO
Check the tuner (TU1101) and its peripheral circuits. Check the tuner(TU1101) and its peripheral circuits.
YES YES
Does the SIF signal come from pin (15) of tuner (TU1101) to pin (75) of Are there the video signal outputs at pins (72) and (70) of connec-
connector (SC501)? tor (SC501) on the TERMINAL unit?
NO NO
Check the line between TU1101 and SC501, and their Check the line between TU1101 and SC501.
peripheral circuits (Q1101, Q1102, etc.).
YES YES
Is there the SIF signal input at pin (75) of connector (SC2203) on the Are there the video signal inputs at pins(70) and (72) of connec-
MAIN unit? tor(SC2203) on the MAIN unit?
NO NO
YES Check the line between SC501 and SC2203. Check the line between SC2203 and SC501 connec-
YES
tors.
Does the SIF signal come from pin (75) of SC2203 to pin (AN23) of Are there the video signal inputs at pin (AM33) and (AM34) of
IC8001 (CPU) on the MAIN unit? IC8001 (CPU)?
NO NO
Check the line between IC8001 and SC2203. Check the line between IC8001 and SC2203 (L2204,
C2229, etc.).
YES YES
Does the audio signal come from pins (4) (COD_LRCK), (5) (COD_BCK) and (6) (COD_SDOUT) of IC1403 to pins (AK24), (AH24) and (AJ24) of
IC8001 (CPU)?
NO
Check the line between IC1403 and IC8001.
YES
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) NO Check the line between IC8001 and IC1402.
(DSP_BCKIN), (AL25) (DSP_SDIN1) and (L32) (DSP_SDIN2) of IC8001 to
pins(2), (3), (6) and (4) of IC1402 (SOUND_DSP)?
YES
Does the audio signal come from pins (19) (DSP_SDOUT1) and (21) NO Check the line between IC1402 and IC1403.
(DSP_SDOUT3) of IC1402 to pins (11) and (12) of IC1403 (CODEC)?
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) NO Check the line between IC8001 and IC1403.
(DSP_BCKIN) and (AL24) (DSP_MCLK) of IC8001 to pins (8), (9) and (10) of
IC1403?
YES
Does the audio signal come from pins (17) (SPOUT_LP) and (18) NO Check the line between SC2203 and IC1403 (D1305,
(SPOUT_RP) of IC1403 to pins (21) (SP_LP) and (25) (SP_RP) of connector D1312, Q1306 and Q1307, etc.).
(SC2203) on the MAIN unit?
YES
Are there the audio signal inputs at pins (21) (SP_LP) and (25) (SP_RP) of NO Check the line between SC501 and SC2203.
connector (SC501) on the TERMINAL unit?
YES
Does the audio signal come from pins (21) (SP_LP) and (25) (SP_RP) of NO Check the line between SC501 and IC2701, and
SC501 to pins (5) (SP_LP) and (9) (SP_RP) of IC2701(AMP) on the TERMI- their peripheral circuits (AMP_MUTE line, etc.).
NAL unit?
YES
4 – 11
LC65D64U
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
4 – 12
LC65D64U
No audio (4)
YES
[INPUT-4 input] If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
[INPUT-5 input] If no video appears, refer to “No external input video (HDMI) [INPUT-5]”.
[INPUT-6 input] If no video appears, refer to “No external input video (HDMI) [INPUT-6]”.
YES
Is the HDMI_MUTE line as specified? NO Check Q1301, IC1302 and their peripheral
circuits.
YES
Does the audio signal come from pins (4) (COD_LRCK), (5) (COD_BCK) and (6) NO Check the line between IC1403 and IC8001.
(COD_SDOUT) of IC1403 to pins (AK24), (AH24) and (AJ24) of IC8001 (CPU)?
YES
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) (DSP_BCKIN), NO Check the line between IC8001 and IC1402.
(AL25) (DSP_SDIN1) and (L32) (DSP_SDIN2) of IC8001 to pins (2), (3), (6) and (4) of
IC1402 (SOUND_DSP)?
YES
Does the audio signal come from pins (19) (DSP_SDOUT1) and (21) (DSP_SDOUT3) of NO Check the line between IC1402 and IC1403.
IC1402 to pins (11) and (12) of IC1403 (CODEC)?
Does the audio signal come from pins (AJ25) (DSP_LRCK), (AK25) (DSP_BCKIN) and NO Check the line between IC8001 and IC1403.
(AL24) (DSP_MCLK) of IC8001 to pins (8), (9) and (10) of IC1403?
YES
Does the audio signal come from pins (17) (SPOUT_LP) and (18) (SPOUT_RP) of NO Check the line between SC2203 and IC1403
IC1403 to pins (21) (SP_LP) and (25) (SP_RP) of connector (SC2203) on the MAIN (D1305, D1312, Q1306 and Q1307, etc.).
unit?
YES
Are there the audio signal inputs at pins (21) (SP_LP) and (25) (SP_RP) of connector NO Check the line between SC501 and SC2203.
(SC501) on the TERMINAL unit?
YES
Does the audio signal come from pins (21) (SP_LP) and (25) (SP_RP) of SC501 to pins NO Check the line between SC501 and IC2701,
(5) (SP_LP) and (9) (SP_RP) of IC2701 (AMP) on the TERMINAL unit? and their peripheral circuits (AMP_MUTE line,
etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
4 – 13
LC65D64U
If no video appears, refer to “No external input video (HDMI) Are there the video signal outputs (IF_OUT_P/N) at the pins(19) and
[INPUT-4/5/6]”. (20) of tuner (TU1101) on the TERMINAL unit?
NO
Is the HDMI_MUTE line as specified? Check the tuner (TU1101) and its peripheral circuits.
NO YES
Check Q1301, IC1302 and their peripheral circuits. Are there the video signal outputs at pins (72) and (70) of connector
(SC501) on the TERMINAL unit?
NO
Check the line between TU1101 and SC501.
YES
Are there the video signal inputs at pins (72) and (70) of connector
(SC2203) on the MAIN unit?
NO
Check the line between SC2203 and SC501 connec-
YES tors.
Are there the video signal inputs at pin (AM33) and (AM34) of IC8001
(CPU)?
NO
Check the line between IC8001 and SC2203 (L2204,
YES
C2229, etc.).
YES
Is there the SPDIF signal (OPT_OUT) output at pin (AP11) of IC8001 (CPU)?
NO
Check the IC8001 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin(2) of IC1304 NO Check the line between IC8001 and IC1304.
(SPDIF_BUFF&MUTE)?
YES
Is there the MUTE signal input at pin (1) of IC1304? NO Check the MUTE_A_ALL and ACDET signals, and their peripheral
circuits (Q1304, Q1312, D1310, etc.).
YES
Is there the SPDIF signal input at pin (1) of D1306 (OPTICAL NO Check D1306 and its peripheral circuits.
OUTPUT)?
4 – 14
LC65D64U
Is the audio output from the monitor set at “VARIABLE” or “FIXED” NO Check the bus line (SCL0/SDA0) and IC1403.
on the menu screen?
YES
Are there the audio signal outputs at pins (24) (LINE_L) and (25) NO Check IC1403 and its peripheral circuits.
(LINE_R) of IC1403 (CODEC)?
YES
Does the audio signal come from pins (24) (LINE_L) and (25) NO Check the line between IC1403 and SC2203.
(LINE_R) of IC1403 to pins (29) and (31) of SC2203 on the MAIN
unit?
YES
Are there the audio signal inputs at pins (29) (LINE_L) and (31) NO Check the line between SC501 and SC2203 connectors.
(LINE_R) of SC501 on the TERMINAL unit?
YES
Does the audio come from pins (29) (LINE_L) and (31) (LINE_R) of NO Check the line between J505 and SC501, and their peripheral cir-
SC501 to pins (2) (L) and (4) (R) of J505? cuits.
Check the LINE_MUTE line and its peripheral circuits (Q507 thru
Q509, etc.).
4 – 15
LC-65D64U
CHAPTER 5. MAJOR IC INFORMATIONS Service
LC-65D64U
Manual
5–1
LC-65D64U
1.10. IC8001 (RH-iXC138WJQZQ)
This LSI is FULL HIGH-DEFINITION 1080P DIGITAL TV SYSTEM-ON-A-CHIP. It combines a cable/terrestrial 4/1024-QAM and 8/16-VSB receiver, a
transport processor, a digital audio processor, a high definition (HD) MPEG video decoder, 2D graphics processing, digital processing of analog video
and audio, analog video digitizer and DAC functions, stereo high-fidelity audio DACs, a 330-MHz millions of instructions per second (MIPS) proces-
sor, and a peripheral control unit providing a variety of television control functions.
The cable/terrestrial receiver directly samples a tuner output with an analog-to-digital converter (ADC). The LSI digitally resamples and demodulates
the signal with recovered clock and carrier timing, filters and equalizes the data, and passes soft decisions to an ATSC A/53 and ITU-T J.83 Annex A/
B/C-compatible decoder. It has an MPEG-2 Digital Video Broadcasting (DVB)-compliant transport processor with advanced section filtering capability,
DVB descrambler, and an MPEG-2 (MP@HL profile) video decoder.
Audio support includes a BTSC and a Dolby AC3/MPEG-2 Layer 1, 2, audio decoder. The LSI provides analog and digital audio/video outputs. A
SPDIF output and a pair of analog outputs (L-R) are provided via the integrated audio DACs. The NTSC analog video decoder is supported by its own
motion adaptive deinterlacing and 3D comb filtering, including 1080i deinterlacing.
The LSI includes advanced 2D graphics processing. Two transport stream inputs are included. The LSI incorporates a complete MIPS32(r)-based
microprocessor subsystem including caches with bridging to memory and a local bus, where external peripherals can be attached. Integrated periph-
erals include two USB 2.0, three UARTs, counter/timers and GPIO controllers.
5–2
LC-65D64U
— MEMO —
5–3
LC-65D64U
CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM
LC-65D64U
Service Manual
㪍㪌㩹㩹㪣㪚㪛㩷㪧㪸㫅㪼㫃
㪈㪐
H
㪈 㪏
㪪㪚㪍㪉㪇㪈
㪈 㪇㪅㪌㪪㪣㩷㪥㪘㪉㪉
㪠㪥㪭㪄㪈㵘㪬㪥㪠㪫 㪨㪚㪥㪮㪄㪞㪉㪎㪎㪮㪡㪨㪱
䇼㪣㪮䇽
㪋㪈
㪈
㪨㪚㪥㪮㪄㪞㪈㪌㪐㪮㪡㪨㪱 䇼㪣㪧䇽
㪣㪚㪛
㪈㪉
G 㪪㪚㪍㪉㪇㪊
㪏㪇
㪨㪚㪥㪮㪄㪞㪈㪉㪍㪮㪡㪨㪱
㪨㪚㪥㪮㪄㪞㪈㪉㪎㪮㪡㪨㪱
F
㪙㪄㪙
㪈 㪈㪉 㪈 㪈㪉
㪈 㪈㪉 㪈 㪈㪉 㪈 㪍
㪙㪄㪙 䇼㪣㪘䇽
㪋
㪈
䇼㪣㪚㪄㪉䇽 㪈㪉 䇼㪧㪣䇽
㪌 㪈
㪈 㪋㪈 㪈 㪈 㪉㪇 㪈 㪋
䇼㪣㪮䇽 䇼㪣㪧䇽 䇼㪣㪙䇽
E 䇼㪢㪤䇽
㪠㪥㪭㪄㪉㵘㪬㪥㪠㪫 㪧㪦㪮㪜㪩㵘㪬㪥㪠㪫
㪢㪼㫐 㪩㪪㪄㪉㪊㪉㪚
㪦㪧㪫㪠㪚㪘㪣
䇼㪣㪘㪄㪉䇽 㪊 㪦㪬㪫㪧㪬㪫 㪙㪚㪤㪊㪌㪌㪊
㪨㪚㪥㪮㪄㪞㪈㪉㪌㪮㪡㪨㪱
㪈 㪈㪉
䌈䌄䌍䌉
䇼㪧㪛䇽 㪈㪉
㪈 䇼㪧㪛䇽
䌈䌄䌍䌉
䇼㪭㪛䇽 㪈
㪈㪌
㪚㫆㫄㫇㫆㫅㪼㫅㫋
㪤㪘㪠㪥
D 㪜㪌㪌㪏
䇼䌐㪜䇽
㪈
㪟㪛㪤㪠㩷㪘㪬㪛㪠㪦
䇼㪟㪤䇽 㪍 㪈 㪨㪚㪥㪮㪄㪞㪈㪉㪋㪮㪡
㪈 㪉㪈
㪭㪆㪣㪩
㪪㪠㪛㪜 㪙㪄㪙
㪈 㪈㪉 㪈 㪈㪉 㪛㪄㫊㫌㪹
㪜㪋㪋㪏 㪉 㪈 㪈 㪍
䇼㪩㪘䇽
㪈 㪈㪉 㪈 㪈㪉 㪈 㪈㪌 䇼㪤㪘䇽 䇼㪤㪘䇽 䇼㩷㪧㪜㩷䇽
㪉㪈
䇼㪬㪪䇽
㪨㪚㪥㪮㪄㪞㪈㪊㪊㪮㪡㪨㪱 㪈 䇼㪭㪛䇽
㪨㪚㪥㪮㪄㪞㪈㪊㪉㪮㪡㪧㪱
㪈
㪪 㪭㪆㪣㪩
㪠㪥㪭㪄㪊㵘㪬㪥㪠㪫
㪨㪚㪥㪮㪄㪞㪈㪊㪋㪮㪡㪨㪱
䇼㪪㪩䇽
B
A
㪣㪜㪛 䇼㪩㪘䇽 㪈㪌 㪈
1 2 3 4 5 6 7 8 9 10
6–1
LC-65D64U
㪍㪌㩹㪣㪚㪛㩷㪧㪸㫅㪼㫃
㪈㪐㪉㪇㬍㪈㪇㪏㪇
㪈 㪏㪇 㪈 㪏㪇
㪪㪚㪍㪉㪇㪈 㪪㪚㪍㪉㪇㪉
㪈 㪇㪅㪌㪪㪣㩷㪥㪘㪉㪉㪉 㪇㪅㪌㪪㪣㩷㪥㪘㪉㪉㪉
䇼㪣㪮䇽
㪈 㪠㪥㪭㪄㪋㵘㪬㪥㪠㪫
㪈
䇼㪣㪧䇽
㪣㪚㪛㩷㪚㫆㫅㫋㵘㪬㪥㪠㪫
㪉
㪪㪚㪍㪉㪇㪊 㪪㪚㪍㪉㪇㪋
㪏㪇 㪈 㪏㪇 㪈
㪡㪨㪱
㪥㪮㪄㪞㪈㪉㪎㪮㪡㪨㪱
㪙㪄㪙
㪈㪉 㪈 㪈㪉 㪈
㪈㪉 㪈 㪈㪉 㪈
㪙㪄㪙
㪨㪚㪥㪮㪄㪞㪉㪎㪌㪮㪡㪨㪱 䇼㪧㪧㪉䇽 㪈
䇼㪣㪚㪄㪈䇽
㪈 㪊
㪈 㪊
䇼㪧㪧㪉䇽 㪈㪉
䇼㪧㪧㪊䇽 䇼㪧㪧㪊䇽
㪧㪦㪮㪜㪩㵘㪬㪥㪠㪫
㪈 㪉
㪈 㪉
㪠㪥㪭㪄㪌㵘㪬㪥㪠㪫
㪪㪬㪙
㪡㪨㪱 㪧㪦㪮㪜㪩 㪈
䇼㪧㪧㪈䇽 㪬㪥㪠㪫 䇼㪣㪘㪄㪈䇽
㪊
䇼㪧㪧㪈䇽
㪈 㪊
㪈 㪊
㪈
䇼㪣㪙䇽
䇼㪧㪨䇽 㪐
㪨㪚㪥㪮㪄㪞㪈㪉㪊㪮㪡㪨㪱
㪈
㪏
㪨㪚㪥㪮㪄㪞㪈㪉㪋㪮㪡㪨㪱
䇼㪧㪨䇽 㪙㪄㪙
㪨㪚㪥㪮㪄㪞㪉㪎㪍㪮㪡㪨㪱
㪈㪉 㪈 㪈㪉 㪈
㪈
㪈 㪍
䇼㩷㪧㪜㩷䇽 㪈㪉 㪈 㪈㪉 㪈
㪏
㪘㪤㪧 㪙㪄㪙
䇼㪘㪚䇽
㪫㪜㪩㪤㪠㪥㪘㪣
㪋 㪈
㪜㪉㪇㪏 㪘㪭㪄㪪㪮
㪩
䇼㪪㪧䇽
㪨㪚㪥㪮㪄㪞㪈㪊㪌㪮㪡㪨㪱
㪪 㪭㪆㪣㪩 㪚㫆㫄㫇㫆㫅㪼㫅㫋 㪭㪆㪣㪩 㪣㪩㪄㫆㫌㫋
㪠㪥㪭㪄㪍㵘㪬㪥㪠㪫
䇼㪪㪣䇽
10 11 12 13 14 15 16 17 18 19
6–2
LC-65D64U
[2] SYSTEM BLOCK DIAGRAM
6GTOKPCN
#859+6%*
5/#(
/#+0
%8$5 8+&'1
%8$5.4 8.4
+0276
;2D2T /CKP;8
%QORQPGPV %1/2
/CKP /CKP%%D
1WV
8+&'1 /CKP%T
G %8$5.4
%8$5
8.4
%8$5 *&8&
+0276
58KFGQ 5 5
#7&+1 #+0.4
8+&'1 1WV
%8$5
%1/2
%8$5 %8$5
8.4 #/2
8
(TQO5+&' 5+&' #/2A/76'
;2D2T %1/2 56#0&$;
㪠㪚㪉㪎㪇㪈
䇼㪪㪧䇽 㪪㪧㩷㪘㪤㪧 2416'%6
㪧㪉㪎㪇㪈 +%
52 㪜㪯㪫㪄㪪㪧
㪰㪛㪘㪈㪋㪎㪪㪱
4GUGV
+(VQ/#+0+(
4
F (TQO%27 (
4
5%
#WFKQ1WV .4 &KUENGVG
&KUENGVG
%QPPGEVQTHQT
/WVG
/WVG
8DTV /QFGN&GVGEV
2
)#+0
8
+% +%
/1&'.A&'6=?
+%
8 +%
8
8 &#% 2TQNFKQO
+% 5% +%
/(2
8 &#% )CVG
4(+0 67 /(2 %QPPGEVQT
+% (TQO*&/+4Z /*\ 2#0'.&GVG
#PCNQI .+0'A/76' +1 65 65
&KIKVCN %8$5 *&/+A/76' +%
-*\8
/
6WPGT +%
-*\8
E +% 2
%8$55;2D2T
#)%#(6
+%A
&A+(
65+0176
.8&5176
5;0% +%
+%
+%A +%
6$ 6*% 866
+%A :VCN
+%
-*\8 +%A
+%
+(KP &&4
#)%#(6 /D
5+(
*&/+KP %08UU
8A# *8
#+0.4 +0 +%
8 4)$KP
8 㪠㪚㪐㪇㪇㪊
%1&'% 52176A.4
+0
6Z&4Z& #-'3 176
㪩㪪㪉㪊㪉㪚㩷㪫㫏㪩㫏 +0
8 *2.4 &KIKVCN+0 +%
45% 㪠㪪㪣㪏㪊㪉㪉㪇 &8+#=?
+0 176
*&/+A.4 &8+%.- $%/ 2
0QRKP4%2CUUVJTQWIJ +0 &8+*5;0%
4)$A.4 ࠺ࡃ࠶ࠣ
+0 176 .+0'A.4 /*\
&8+85;0% &KIKVCN#8FGEQFG/CKP%27 㩄㩒㩂㩊
D :: VCN
&8+&'
7#46$
7#46%
6Q456
5QWPF&52 ''241/ 0A%27A456
75$
+0276 &57$ : VCN 8*+0,7; MDKV 4'5'6
4)$ /*
+%
-*\
+% 0A54'5'6
''241/
C +0276 *&/+ 4:AZ
+%
-*\8 0A&$)A456
/*\
+%
8+%
''241/ 6/&559
+0276 +%
*&/+ 5++
8
4:AZ ''241/ +P : VCN
8
/*\ +%
+P +% 2
*&/+4: 㩉㩖㩎ᦠㄟߺ↪ (.#5*
+P 5++ 㩄㩒㩂㩊 /D
5+&' 5GNA
;%D%T
&
+0276 %8$5
%1/2%8$5 .4
6Q6GTOKPCN
+(VQ/#+0+(
+%
''241/
+0276 5% +%
*&/+A 6/&5
B 5++
6GTOKPCN
, *16'.
75$
ޣ4#ޤ
ޣ4#ޤ
.'&
4%
12%
.'&
A
1 2 3 4 5 6 7 8 9 10
6–3
LC-65D64U
RKP
RKP
+%
((%
㧸㧯㧰
ޣ.2ޤ
ޣ.2ޤ
2
2
92 䌃䌯䌮䌤䌯䌲
&'6'%6
%106 㪣㪚㪛
㪧㪘㪥㪜㪣
((%
䌃䌯䌮䌤䌯䌲
㪈㪐㪉㪇㬍㪈㪇㪏㪇
ޣ.9ޤ5%
ޣ.9ޤ2
R
R
5*+2A'020'.A'0
((%
((%
$7
8
+% $7
8
4GUGV +% 6Q*&/+
)CVG *&/+A%'%A+0
456A*(.5A%2.&
㧮㧸
%'%A1A7%1/
%'%A+A7%1/
(TQO%27 (.#5A9A%2.&
&'6A20.8
45A$7(A%06
9CXGNGPIVJ
5%
%QPPGEVQTHQT
41/5'.
$7
8 (4#/'4.7&6'/2=?15A5'6
/QFGN&GVGEV
+1
4Z&6Z& +1 56$ 8QP
(TQO%27
+% 56$A%27
/1&'.A&'6=?
5% +%
(TQO%27 8DTV +08'46'4 +08'46'4
)CVG
%QPPGEVQTHQT
9*(7 +%
RKP
2#0'.&GVGEV +%
ޣ.$ޤ
/%
2
''241/A5%.5&#
RKP
RKP
4Z&6Z&
ޣ.%ޤ
ޣ.%ޤ
7#46 /QPKVQT/KEQO $7
8
6JGTOKUVGT 6*'4/1 +%
#& 92 ''241/
#(6 #& 5%5,
20.A&'6=? '44A20.
.8&5176
RKP
+% /*\ /*\
ޣ.$ޤ
#%A&'6
866 :VCN
2/A4'3%$1165 +1
+1
+% 0A54'5'6 +1
&&4
/D ޣ.#ޤ ޣ.#ޤ
+06 #& +1 +1 +1
RKP
RKP
%08UU
ޣ.#ޤ
R
+%
219'4
8 219'4
$%/
8
2
࠺ࡃ࠶ࠣ↪
㩄㩒㩂㩊
&'6A20.8&'6A8&'6A8
ޣ22ޤ219'4
2+0
*2A2.7)
+1
ޣ22ޤ219'4
2+0
12%A.'&219A.'&A4219A.'&A).'&A;1;#-7
7#46$
7#46%
75$
25A10
$CEM7R
˴$7
8
ޣ22ޤ219'4
#%A&'6
$7
8
2+0
ޣ2&ޤ219'4˴2
2+0
-';-';56#0&$;219
/#+0
˴#8
+% ˴#8
(.#5* ˴&8
˴&8 748
˴&8
˴&8 $78
˴8.8
˴&8
*2 2.7)
˴&8
4%
12%
˴GVE 20.A10
(TQO%27
ޣ23
ޤ2+0
$7 8
219'4
IC8502
IrSimple
ޣ4#ޤ2
R ޣ-/ޤ2
R ޣ#%ޤ
ޣ4#ޤ2
R ޣ-/ޤ2
R
R
㪠㫉㪪㫀㫄㫇㫃㪼
.'& -';
㪤㪜㪥㪬
㪧㪦㪮㪜㪩
㪠㪥㪧㪬㪫
4% 㪚㪟㪄㪬㫇㪆㪛㫆㫎㫅
12% 㪭㫆㫃㪄㪬㫇㪆㪛㫆㫎㫅
.'&
10 11 12 13 14 15 16 17 18 19
6–4
LC-65D64U
CHAPTER 7. PRINTED WIRING BOARD ASSEMBLIES
LC-65D64U
Service Manual
1 2 3 4 5 6 7 8 9 10
7–1
LC-65D64U
11 12 13 14 15 16 17 18 19
7–2
LC-65D64U
VER1
KOUJO1
I P9001
D9606
Q9602
LUG2202
D9608
C9613
P9701
R9306
C9612
C9616
R9705
L9603
C9631 D9701 P9301
D9601 C9709
C9711
R9704
TL2668 C9624 Q9702 R9736
FL8004
P2603
R2623
C2606
R2621
C9645
R2633 D9607 R9618 D9702
L9602
C9625
R2634TL2653
C9622
TL2667 Q2602 D9609
L9641 R9307
TL2666 L9601
R9615
C9646
C9618
C9619
R2632C2610
H C9621
C9620
Q2601
R9302
D9602 IC8452
C2605R2620
R8453
R2619
C2604
TL2654
C8458
C8174
C8186 C8204
FL2615
P2602
R8025
R8239
C8189
R8266
R8197
R2629
R2636
R8254 R8222 R8032
R8018
R8015
R8265
R8238
R8196
IC8153 R8095
R8082R8083
R8008 R8005 R8069
TP8049
C2246 R8098
G
C2247 R8099
R8253 R8221 D8002 C8135 C8136
R8035
R8135
R8264
TP8084
R8237
R8195
X8001
R8011
TP8047
TP8042 TP8016 R2279
C8203 C8200 C2238
R8023
FL8001
R2280
TP8002
R8130
C8607
L8001 C2240L2206C2236
C2229
R8088
C2241
TP8010
L2204
L2207
R8132
C8175
C8201
R8089
R8087
R8086
R8085
C8134
C8190 C8202 C2239L2205C2235
R8123 R8003
TP8081
R8236
R8194
R8605 TP8022
R8193
R8602
R8262
R8002
C8089
R8106
R8040
R8618 R8249 R8219
R8617 IC8601 R8094
R8261
R8234
R8192
R8607 TP8077
C8127 R8056
R8608 C8198 C8119 R8046
R8610 C8118 R8045
R8158
R8615
R8620 C8147 R8109
C8148
R8110
C8131 R8072
IC8001 C8132 R8073
BAR1 C8133 R8074
R8156
C8129 R8070
C8130
R8071
R8155
C8121 R8048
BAR3
C8123 R8050
C8197 C8122
R8154
R8049
R8026
C8165
R8905
C8172 C8196 C8124
R8051
R8182 R3343
R8233
R8191
R2601 R2602
E C8173 R8183
R8260
R8218
R8151 R8152 R8153
R8248
R3348
R8232
R8190
TL2663 Q2603
R8259
R2635
IC8151
TL2665
R3347
R8108
R8247 R8217
R2603
R8107
R8189
C8145
R8258
R8231
TP8001TP8044
C8146
R3346
R9209
R8024 R8143
C8141
R8104
R8117
R8125
R8113
R8127
R8126
R8128
R8006
R8139
C8139
R8102
R8146
R8103 C8142
C8153 C8155
R3345
C8140
R9007
R8101
R2616
C8164
R8188
TP8012
C8171
R8257
FL8005
L2605 TP8015
TP8045
L2610 TP8048
TP8051
R8246 R8216
P2601
D L2604
R8269
R8268
R8187
IC8152
L2609
R8245 R8215
L2603
R8186
R8255
R8228
L2611
L2608 C8151
L2602
L2607
P9202
L2601
C L2606
R9023 C9003
C9007
C9002
C9001
LUG2201 LUG2203
C9008
R9024
IC9003 IC9001
C9009
D9005
IC1304
Q9001
R9206
R9002
R9022
R1333
D9001
C1310
R1311
R9021 FB9002
FB9003
SG1610
R1603
SC9202
P2203
D1306
B FDC1
SC1601
SC9001
1 2 3 4 5 6 7 8 9 10
7–3
LC-65D64U
SC2203
C8515
R9306 R8511 SC9201
R8510
R9014
IC8502 R8514
R8512 FDC3
R1331
R1327
R8502
R8513
Q1303
Q1313
P9301 R8515
R1325
C9708
R2035
C8514
C2209
R2312
R2311
C8513
R8508
R8509
R2309
R2310
IC2203
R2051C2015
R2052C2014
X8501
P2001
LUG2204
R2016
R9004
C9010 IC9704
R8503
R9303
R9304
R2066
D9303
C2020
R9013
R9005
R2017
C9304
IC9004
IC2008
C9719
R2015 R2075
R2041D2003 R2077
IC9301 R9305
R9311
C2018R2061
C2017R2060
C9301 R2072
R2048 R2014
R9740
C9302 C9303 R9741R2068 C2026
R9738
R9739
D9301 D9302
C8458
R1412
R2220 R2283
R1417
R1419
R1420
R2211
R2213
R2202
R2219
R2209
R2216 R2203 R2201
R2210
R2207
R2218 R2206 R2205 R2217
Q2206
Q2203
R2276
R1413
Q2202
Q2201
R2277 Q2205
R2273
C2232
TP2202
IC1402
C2234 C2233
R2274
C2231
C2246 R8098
TP2203
C1405
C2247 R8099
R1403
C1411
R1421
C1417
R1449
R2279
C1418
C2238 C1412
R2280
C2240L2206C2236
R2269
C2229
C2241
L2204
L2207
R2316
R2010
R2270
C2239L2205C2235
R2278
R2275
TP2204 R2047FB2005
R2272
R2235
Q2216
C2237
C2230 R2009FB2004
C8093 C2005
LF1 R2008FB2003
C8107 C8091 C2004
C8089
R8040
C1431
C1432
R8094
R1407
C1457
R1416
R8058
C8128 TP8078
C8125 R8052 FB3301 R3334TL3304
C3301
C3328
C3319
R3335
R1418
P2002
C8126
R8054
TP8076 R3321
C8127 R8056
TP8077 R3315
C3325 C3337
TL3302
C1419
C3327
C8119 R8046
FB3302
C3330
C8147 R8109
C8148
R8110 C3312 R3313
R8906
C8131 R8072
C1437
C3311
X1401
C8132 R8073 R3312
C8133 R8074 C3310
C8129 R8070 IC3301 R3310
P2201
C3309
R3330
C8130
R8071 R8907
C8121 R8048 C3308 R3308 C1401
C8123 R8050
C3307
C8122 R8049 R3307
R8026
R8905
C8124
R8051 C3306
R3316
R1435 R1436
FB3304
P2202
C3336
C3314
C3324
C3323C3322
R9012 R3327
R3326
R8908
C3313
R3340
C3332
R3348
R3322
C3331 FB3303
R3347
C1438
D1311 R1337
R8909
R3346
R1336 R1312
R8146
R3345
P8011TP8014
TP8013 D1307 D1312 D1314 D1309
P8012
TP8045
P8015
C3219
D1303
TP8048
TP8051 X3201
D1305
D1313
D1308
D1304 R1308
R1304
R1341 R1309
SC1603
R3233
R1739
R1740
R1741
R1742
R1743
R1744
R1745
R1746
R1677
R1676
Q1620
R1725
R1726
D1310
Q1619 TH2001
R1606
C2223
L2202
R1605
R1681 Q1610
R1679
R1625
R8012
Q2213
D2208
C2222
C2220
C2218
R2225C2212
R2223C2211
C2221
C2219
C2217
IC1604
IC2202
FB2208
R1727 C2215
R2242
R2252
LUG2205
TP1633
C2216
R2233 R2238
D2207
D2206
D2205
R2230 D2203
C3202 R2212R2215
D2202
C2228
IC2201
FB2202R2208
FB2201R2204
C2214
C2227
IC1608
C1676
R2229
FB2206
R1613
R1617
C1604
R1618
R1614
FB1602
FB1601
R1615
C1603
R1619
SG1604
SG1603
SG1609
SG1615
SG1621
SG1601
SG1607
SG1613
SG1619
SG1602
SG1608
SG1614
SG1620
SG1616
SG1610
R1603
R1601
SG1622
J2201
SC1601 SC1602
J1601 SC2201
11 12 13 14 15 16 17 18 19
7–4
LC-65D64U
1 2 3 4 5 6 7 8 9 10
7–5
LC-65D64U
11 12 13 14 15 16 17 18 19
7–6
LC-65D64U
TL2289 TL2285
TL2317 TL2282
TL2280
TL2278 TL2272
TL2277 TL2314 TL2269 TL2275TL2266TL2311 TL2309
TL2271 TL2307
TL2305TL2303
TP2206 TL2236
TL2284 TL2316
TL2283 TL2288 TL2256 TL2281 TL2274
TL2279 TL2273
TL2247 TL2270
TL2313 TL2276TL2268 TL2228
TL2310
TL2308
TL2306TL2304
R2314 TL2229 TL2249
TL2242
R2313 TL2245
TL2287 R2306 R2308
TL2265
TL2226
TL2224
TL2312TL2207 TL8506 TL8505
TL2299 R8507 TL8501
TL9334
I TL2257 TL2300TL2250 TL2302 TL2255 TL2234 TL2227 TL2223
TL2225 TL2208 TL9353
R2307
TL2252 TL2244 TL2240 TL2267 TL9327
TL9330
TL9333 TL9326
TL2298 C2002 TL8507 R8506
TL8502 TL9335 TL9
TL2315
C8512
TL2301 TL2286 TL2243 TL2233 TL2209
IC2001
TL2251 TL2241TL2235 R1326 R2003 TL8508 C8507
TL9
TL9381 TL9316
TL2239 TL2237 TL9212
C8508
FDC4 TL9332
TL9336TL9345 TL9329
TL9328 TL9383
Q2006
TL2254 R1328R1321 C8510 TL
TL931
TL2238 R1318 Q2001
R1330
TL9219 C8509 TL9331
Q1314
R2007C2003 X2002 TP2007TL9211 TL9380
TL9344
R2001
TL2248 TL2246 TL2253
R2076
Q1302 C8511
R2050
Q2007 TL9379
R2034
C2001 TL9213 R2006
C1456 R1448 C1454
C8456 T
R2046 R2049 TL9337
TL9352 TL9340
TL9343
TL9346
TL9349
R1329
R1317
R2070
R2071
R2005
C1449 TL2011 TL2014
TL2007TL2009
C1452
R1440
C2016
C2010 TP2009
R2036 TL9209 TL8503 TL8504
R2026
TL9720 TL2006 TP2013TL9210
R1447
R1446
R1445
R1443
TL2012 TL2001
TL2008 TL2010 C8503 C8501 TL9342 TL9348
TL9339 TL9351
R2013
R9008
TL9354
C1455
R2025
TL2013 C8504 C8502 TL9338
TL9341 TL9347
TL9350
C2012
R9201
TL8455 TL9357
C1453
R1444
R8474
R8475
TL8454
R8456
R8457
R9010 TL9310
IC1406
R9011
C2008
TL8456
IC8501
IC9002
R2023
R2024
R1442 C1447
R1441
C8453C8452 C8460
C8451 C8462C8461 TL935
TL8453
C1450
C1451 TP2003
TP2011 TL
C1448
IC2002 C8506
H
R2012
R2042
R9312
C9004
R8501
IC8451
IC8454
TP2001 R9009 C8505
R1439 R2033R2032
R1438 TP2014
R9308
R9205
TL2201 TP2005
TL2212
C1445
TL2221
R1437
C1442
R2004
R2029
R2011
R2019
TL2203 TP2004
R2287
R2286
R2221
R2214
R2289
R2288
R2058
R2044
C2013
TL2222 IC2007
TL2220 C1443 R2293 R2078
TP2015 TP2012
R2291
TL2219 R2292 R2284
R2290 R2266
Q2204
TL2218
Q2217
TL2217
Q2207
Q2215
IC1405
TL2216
TL2215
TL2214 C2208
TL2213 C2206 C2202
C1444
G TL2202
FB2001
R2265 TP2201
R2236
R2271
Q2214
TL2005 TL2210
C2242
C2029
R2263
C2028
TL2004 R2222
R1422 R2224
R1431 C1429
TL2003
R2267
R1432 C1430
TL2002
R1425
R1414
C1440
C1441
C2027
C1414
Q2209
R3344
C1415 C1424
C2204
FL3301
R3320
R3319 R3349
R1415
C1426
C1425
R8043
R8053
R8021
R1408 R3331 R8057 TP8074
IC1403
R1409 TL2335
C1427
R8062
R1410 R8064 R8904
R1411 TL2333
F R8063 FB8007
C1428
C1406 TL2332
R1427 C1433
R1428 C1434
C3333
R8111 R8077
FB8008
R1405
R1406
R3329
C8905 C8909
R1450
TL2211 FB8009
R1402
R3341 TL2331
TL2334
C1408
C3302 FB8010
R1401
R8078
C3334
C3329
IC1401
TL2336
FB8011
R3318
R8075
R8066 TL8005
C1402
TL8006
C1403
C3315
TL2329 R8067
C3335 R8068
C3326 TL8008 TL80
R8084
C1436
C1435
R3317
C3316
TL2322
R3353
C3303
TL2323
TL2325 IC1404
TL2324 R1434
IC3302
TL3301
R2297
R2298
TL2321
E TL2326
C3304 R3235
C3211
C3209
C3208
R3224
R1335
C8082
C3224R3209 C3221 C3217
C3207
TL2320
C3201
C3203C3206
C3228
TL2328 R1315
R1314
Q1309 Q1307
R3212
C1301
C3205
TL1611
C3231
C3218
R1602
FB1603
Q1616
R1301
C1607
Q1305
IC1301
R3234
R1322R1324
C1609
C3210
R1684
R1627
R1303
C1653R1686
R2304
R2305R2294R2256
D D1605
R3207
C1675
C3230
D1601 R1604
C3229
IC1607
IC1603
TP2205 D1614
Q1301
Q1304
R1685R1687
R1729
C3204
R2296
R2295
TL2290
Q1618
R1630
C1678
R2300
C1615
C1620
D1611
D1613
R1680 C1613
C1612
TL1618
R1641
R1683
R1307IC1302 C1619
IC1609
C1648
R1678C1674 C1637
R1671 R1673
R1668 R1669
C1640
C1641
R1688
R1610
C2225
C2226
R2247
C1630 TL1613
C1673 C1636
C1638C1646C1634
D2211
R1674 R1640
C1652
C2224
R2243
D1607
C1679
TL1622 C1621 R1665
R1623
TL2296 TL2297
C1642
C1628 C1624
D1604
C1618
C1633 Q1609
Q1603
R1724
TL2264 TL2263TL2262TL2260
1 2 3 4 5 6 7 8 9 10
7–7
LC-65D64U
R9602
C9606
R9607
R9601
R9608 TL9005TL9003TL9002TL9001
TL9701
R9603
C9609
TL9702
TL9715 TL9710 C9605
TL9724
TL9708 TL9733
TL9717 TL9716 TL9711 C9601
TL9325 R9606 IC9601
TL9729
TL9731
TL9732
TL9723
R9035
R9034
TL9334 TL9324 TL9323
TL9382 R9605 C9611
TL9734
TL9730
TL9727
TL9728
TL9725
TL9726
53 C9005
C9608
TL9333 TL9327
TL9330 TL9326 R9604
C9610
R9613
L9335 TL9313 TL9322 TL9321 R9629
C9718
TL9603
TL9315
TL9381 TL9316 TL9320 TL9319
TL9312 C9602
R9609
C9710
TL9332
36TL9345 TL9329
TL9328 TL9383 TL9314
TL9317 TL9311TL9318 D9703
FB2603
IC9703
C9615
TL9601
C9623
TL9331 IC9605
TL9375 TL2601
TL9344
L9380
D9713
C9643
TL2652 TL2669
C9614
Q9701
C9617
TL9379 TL9301
TL9722C9713
IC9602
TL9302 R9614
C9629
2L9337
TL9340
TL9343
TL9346
TL9349 TL2621
R9316R9318
TL9378
Q9301
R9616
R9617
C9641
C9642
IC2602
R9314
TL9602 TL2610
TL9342 TL9348
TL9339 TL9351 D9603
4 D9643 C9607 D9641 IC9641
TL9338
TL9341 TL9347
TL9350 TL2609
R9644
TL9384 R9642 TL9604
C2609
R9625
R9611
R9645
TL9355
R2638R2637 C2602
TL9359
IC2601
TL8457
R9308
R2631
C8229 C8178 C8176 TL2648 TP2605
R2604
C8228 TP2601 TP2604
C8206
C8205
TL2635 TP2603
R8214
TL2634 TL2637
TL2636
R8029
R8037
R8030
R8055
TL2631 TL2638
TL2633
R8223
R8224
R8213
R8007 R8010 R8009
FB2602
R8016
TL9385 TL2629
TL2630
R8017
R8140
TL2632
TL9386
TL9303 C8184
R8212
C8185
R9324
R8034
R8116
R8031
R9317
C8227 C8216
C8180 C8182 R8033 R8028 R8027
C8226 C8179 C8177
R8180
R8093
R8122
R8211
R8120 C8606
TP8055
R9018
C8092
R8611
R8014
TP8020
R8179 R8178
C8072
C8074
C8084
C8073
C8070
R9313
R8013
R8096 TP8041
C8078
R8141
R8612
R8097 R8036
TP8625
C8088
R8114
R8210
C8090 R9310
C8114
C8608
C8100
C8077
R8177
C8099
C8071 TP8050
C8215 C8611 TP8626
R8209
C8101
R8043
C8115
C8043
R8053
R8021
R8059C8044
C8046
C8050
R8175
R8164
FL8002
C8225
R8062
R8064 R8904
C8610
C8902 C8056 C8053
R8616
C8214 C8609
C8019
R8198
R8063 FB8007
C8901
C8912 C8914 C8916
32 C8020 C8213
C8605
R8111 R8077
C8041
C8913 C8915
FB8008
C8903C8907
R8199
TL8151
R8200
2334 C8210
C8025
C8013 C8039
R8271R8270
C8194C8195
C8096 C8192
R8201
36
C8010 C8037
C8109
FB8011 C8031
R8075 C8149
TP8052 C8209
C8004 C8045 R8181 TL8152
C8008
C8006
C8009
C8052 R8163
R8202
C8104
IC8155
TL8006 C8035 R8168
C8036
C8193
R8174
C8063
C8007
TL8008 TL8007 C8112 C8207
C8040
C8057
C8030
C8028
C8061
R8084
R3352
TP8054 C8066 C8060 C8034 C8224 C8159 C8157
R8173
R3350 C8029
C8051
R8100
R3351
R8208
C8002
R8129
C8012
R8172
C8059 TL9605
C8032
C8062
C8016
C8079
R8171
TL2655
TL2656
C8075
C8024
R8144
R8207
R8039 C8026
C8106
C8069R8038
TL2662
TL2661
TL2660
R8167
R8170
C8105
C8064
C8081 TL2651
TL2641
FB8002 C8076 R8251
C8065
R8137
R8136
C8067
FL8007
R8206
C8003
R8001 TL2640TL2645
FL8006
C8082
C8080
C8168 TL2658
TL2644
R8124 C8167
C8014 TL8033C8085 C8223 C8222 R2622 TL2643
TL2659
C8161 C8163 C8217 R2615TL2639TL2642
FB8003
TL2657 TL2603
R8205
FL8009
FB2608
TL2628
R8150
C8086
TL1611
R1602 FB2607TL2627
FB1603
Q1616
TL8029
R8204
C1607
TL2626
C1609 TL1619 FB2606
IC8002
D1603
R1627
R1723
D1605
R8203
Q1605 C8169
TL1616 C8170
IC1601
R8226
R8225
R1612 FB2605TL2625
Q1602
C8218
C8219
R1630 R1629
TL1609 C8220 C8160 C8162 TL2623
R1607
C1615
Q1607
TL9201
D1611
D1613
C1613
R1620
FB2604TL2624
TL9203
TL9241
TL1606 TL9206 TL9240
TL9239
R9204
R9212
TL9224
R9207
TL9204
TL9223
R9208
R9202
TL9221
R9211
TL9208
TL9202 TL9207
TL9205 TL9222 C9006
LF2
TL9006 TL9008
TL1303 TL1304
TL9010 TL9007 TL9004
TL9275 FDC2
BAR4
11 12 13 14 15 16 17 18 19
7–8
LC-65D64U
[2] TERMINAL Unit
H TERMINAL Unit
(Side-A)
1 2 3 4 5 6
7–9
LC-65D64U
6
TP502
C2735
Q2701
R2747 C2739
R2751 R2750 R2749
C2736
IC502 P2702
C572
5
Q2703 Q2702 R2746 R2745
R2740 R2743
C2746
D2705
CAME1
FB2706
FB2708
FB2707
TP2701
FB2709
R2719
R2718
R2708
C2703
C2747
FB2701
R578
FB503
R2701
P502
R577 C568
Q509 Q507
SC501
Q508
C2710
FB504
R576
R583 R584
R587 R586
C2717
C2724
C2712
C2711
R2709 R2726
C2704
R2702 R2725
R528 C501
R519 C503
C2705
R2703 R2730
C2713 IC2701
R2752
R2706 R2731 L2702 C2730
4
R534
R532
R530
R525
R524
R521
C2706
R2710 R2742
L1101
C552
C549
R2715 C2741
C534
C533
C531
C529
C528
C526
C525
C519 C523
C516 C521
C577
C576
C515
C1111 R2741 Q2704 FB2702
R2705
R1117
C547
C1110
D524
C1128
C2748
C2723
R2717
C2716
IC503 R2707
C1125
C543
R1129
D506
C510
C537 R2754 FB2703 C2740
C509
C1108 R1128 C1122 R1130 R2713
FB514 C550 R513
C1124
C2744
C2745
C1112 C1121 R508 D2703
7 – 10
R1121 R573 C546 R507
IC1103
R1107 C1120 R1127
R529
R544
Q506
P2701
R526
R567
R564
R571
C507
R1110 R1125 Q505
R505
C2743
D512 R1109 C1119 C559 R568 IC501 C518
R1123 C1133 C545 R504 D2702
C1118
C506
FB510 C1107 R562 R559
R522
R503 C524
Q504
C1117
Q1101
R556
R553
R1126
R1124
R1113 C1132 C1115 Q503 FB2704
C544
D511 R561 R502
R557
L2704
L2703
C530
C505
C2738
C512
FB509 R1115 C1113 R1122 C564 R501
R1119 C2742
R1114 R549
C1116
C1114
C539
Q502
FB508
R516
R546
R543
R551 Q501
C504
FB2705
P501
C2728
C2727
C1104 R550 C574
D2701
R1103 C1131
C520
C517
C514
R520
R518
R517
D513 R589
C527 R588
D523 R523
D509 C522
R514
D514 C513
C554
R533
C532 R531
C536 R537
R527
R538
R595
C2737
R597
R1106
R596
FB507
R515
R1116
Q510 C2731
C575
R1102 C541
R594
R593
D507 IC1102 C1106 IC1101
D508
FB506 R511 R1101 R1111 R1104
C1105 R1105 C1103 TP2702
3
R2714
R512 C511
TU1101
FB505 R509
R510 C502 C1102 C563
D519
FB1102 R569
FB1101
C562
C561
R585
FB520 R565
R566
TP503 C566 TP501
TP1101
C569
C570
FB522
FB523
FB521
R580
R579
R582
R581
C553
C565
R572
C560 C551
D521
FB524
R563
C1101 D520 C548
R574
C573
R542
R541
R591
R548
D516
D515
D522
D517
FB517
C555
FB512
C542
FB516
FB515
FB513
FB502
C535
FB511
C540
FB518
C556
C557
R560
R554
R552
R545
C538
R539
R540
D518
R535
R536
C558
R558
R555
R590
FB519
J504
J506
J505
J503 J502 J501
2
TERMINAL Unit
(Side-A Chip)
1
G
H
A
E
F
LC-65D64U
[3] SIDE Unit
1 2 3 4 5 6 7 8 9 10
7 – 11
LC-65D64U
k2 k1
k3
R915
FB904 R911
I
D904
J902
FB905 R912
D905
P901
R913
D906
FB906
R906
D903
FB901
G
R914
R907
LUG902
F
C903
J901
FB902
R909
v1
R908
C904
FB903 R910
E
Q802 IC807
R834
R838
C829
R803
D803
C827
IC804
Q801
R833
Q803
FB802
C806 C808
R828
R825
R826
D801
C807 C809
C813 C819
D D809
R801
C815
SG801 C832
R817
R827
C814
L801 C818 R813
SG805
SC801
C833
SG802
L803 R829
SG806
SG803
L804 L805
SG807 IC803
L806
SC802
SG804
L802
R837
SG808
L807
R810
D805
C831 C820
C811
C830
C817
R816
C822
C823
C810 C821
R814
Q804
R811
R831
C816
Q805
C825
R808
R807
Q807
D810
IC805
R812
IC806
D802
Q806
R802 IC802
R836
C802
C803
J802 C824
FB805 R835 C826
C804
R823
C828
R804
R822 D806
C801
C805
IC801
R805
B R820
R809
P801
R821
R819
VA802
J801
VA801
LUG901
1 2 3 4 5 6 7 8 9 10
7 – 12
LC-65D64U
[4] R/C, LED Unit
3
H
R101
C107
C102
R/C, LED Unit (Side-A) R/C, LED Unit (Side-A Chip)
SLD101
RMC101
G
D101
R132
IC101
C105
C104
R136
R135
F
R102
R105
D103
R117
R137
R108
Q104
R109
R104
R107 Q102
Q103
D114
R138
R106
Q105
R121
R126
R110
R123
Q106
R127 D115
D R122
Q107
R124
C110
C108
C101
R103
RMC102
C
R119
R120
D116
R116
C103
IC102
R118
C111
B
P101
R139 R140
P102
1 2 3 4 5 6
7 – 13
LC-65D64U
[5] KEY Unit
S155
D152
G S154
S152
F
R151
D151
S151
R152
S153
D
R154
S156
S157
B
D155
A
P151
1 2 3 4 5 6
7 – 14
LC-65D64U
CHAPTER 8. SCHEMATIC DIAGRAM
LC-65D64U
Service Manual
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
8–1
LC-65D64U
[2] SCHEMATIC DIAGRAM
KEY Unit
1 2 3 4 5 6 7 8 9 10
8–2
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8–3
LC-65D64U
11 12 13 14 15 16 17 18 19
8–4
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8–5
LC-65D64U
11 12 13 14 15 16 17 18 19
8–6
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8–7
LC-65D64U
11 12 13 14 15 16 17 18 19
8–8
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8–9
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 10
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 11
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 12
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 13
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 14
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 15
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 16
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 17
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 18
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 19
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 20
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 21
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 22
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 23
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 24
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 25
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 26
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 27
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 28
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 29
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 30
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 31
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 32
LC-65D64U
TERMINAL 2/3
1 2 3 4 5 6 7 8 9 10
8 – 33
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 34
LC-65D64U
TERMINAL 3/3
1 2 3 4 5 6 7 8 9 10
8 – 35
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 36
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 37
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 38
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 39
LC-65D64U
11 12 13 14 15 16 17 18 19
8 – 40
LC-65D64U
1 2 3 4 5 6 7 8 9 10
8 – 41
PartsGuide
LC65D64U
PARTS GUIDE
No. SY7C3LC65D64U
MODELS LC-65D64U
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
3
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
4
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
5
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
6
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
7
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
8
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
10
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
11
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
12
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
13
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
14
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
15
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
16
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
17
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
18
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
19
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
20
LC65D64U
[8] NOTE (Conductive cloth tape)
1
2
3
4
5
6
2
1
3
21
LC65D64U
[9] NOTE (Temperature-proof cover)
Added cover parts
1 Cover partcode: PSPAGA386WJ00 Q'ty 5
2 Cover partcode: PSPAKA237WJ00 Q'ty 1
1 1 1 1 1
Attention
Please peel off the covers when you remove Rear Cabinet.
And please use the NEW cover when you install Rear Cabinet.
(When using the cover again, keep in mind the decrease in the adhesive power of the cover.
The purpose of using the NEW cover is to prevent the cover from peeling off.)
22
LC65D64U
[10] CABINET AND MECHANICAL PARTS
42
67
67 41 67
5
67
67 5-1
31 5-2
37
1 38
1-1 1-7
1-8 67
4
1-10 1-7
1-8
1-7 67
1-2 1-7
1-6
1-8
31
1-7
81
1-7 76
1-8
81
1-9 1-5 10
81 81 63
71
64
53 2-2
69
12
1-4
61 1-3
81
74 26
54 7 73
74
62 7 6 2-1
55
67
67 58 6-1
49 83 82 2
67 67 6-2
84 67
56 32 72
67
48
36 60 72
33
50 24 23 70
43 39
45 43 19
23 21
25 3-4 35
29 67 25 24 47
28 57 27
24 27 67
67 86
25 24
25 25
51
27 25 34 3-2
67 15
25 3-3 80
65 77
65 3
65 67 46
80
17 20 44 66
65 67
52 9
11 75
16
14 30
67 13 40 68
17
85 22 30
74 22
65 59 8
23
18 79-1
65 79-2 79-3
21 23 22
74 22 79 79-4
16 27
27 23
23 23 79-3 79-4
27 79-4
23 23
18 65 79-5
79-3
27 23 79-4 79-3
23 78
79-5
78
23
LC65D64U
24
LC65D64U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
X1 X2 X3 X4
X8 X9 X10
25
LC65D64U
[12] PACKING PARTS (NOT REPLACEMENT ITEM)
S7
S8
S5
S5
S6
S5
S1
S3
S4
S9
S5 S5
S5
S5
S2
26
LC65D64U
27
LC-65D64U
COPYRIGHT ©2007
XXXX BYSHARP CORPORATION
ALL RIGHTS RESERVED.
SHARP CORPORATION
AV Systems Group
Dec. 2007 CS Promotion Center
TQ2410-S SH. DS Yaita,Tochigi 329-2193, Japan