Professional Documents
Culture Documents
P-39 Airacobra: Safety Precautions
P-39 Airacobra: Safety Precautions
Specification:
Length: 1788mm(70.4")
Wing span: 2040mm(80.3")
Wing area: 78.5sq.dm(8.5sq.ft)
Wing loading: 93g/sq.dm(30.5oz/sq.ft)
Flying weight: 7.3kg(16.1bs)
Radio: 6ch & 8servos INSTRUCTION MANUAL
Engine: 30cc gasoline engine
4-cycle .180
Spinner
18″X10
We strongly recommen you use the thread lock for all the screws when you build your model.
Accessory list for the coming installation steps.
3 Assemble the aileron to main wing with instant type AB glue. Be careful
to ensure the moving parts of the hinges are able to move freely.
Strut
3-way
pressure inlet
1 Apply instant AB glue to aileron and pin hinge.
4 Install the servo as the illustration below
3-way
pressure inlet Pin hinge(24x24mm)
6
3-way 3-way
Strut pressure inlet pressure inlet Strut
Air inlet
2 5
Quick release connector
Keep some space about 1mm width between
Install the nylon control horn and connect the linkage.
aileron and trailing edge.
Pressure reduction inlet
Ø0.2mm
Switch Trailing
edge Retainer
Ø1.7mm Rod (2x300mm)
Aileron
Clevis
Clevis
Screw (2x10mm)
Lock Nut (3mm )
Washer(3x15mm)
3mm 150mm
Washer 1mm
Make sure they are in
the right position while
Screw (3x40mm) installing.
Clevis
2
Retainer 2
Rod (2x300mm) 2
TP Screw (2.3x12mm) 8
Screw (3x30mm) 2
Servo tray(68.5x56.5x2mm) 2
Wooden Block(20x20x8mm) 4
Pin hinge(24x24mm) 8
Washer(3x15mm) 2
Lock Nut (3mm ) 2
Washer(3x15mm) 2 Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Pin hinge(24x24mm)
8
2 15
70 Epoxy the landing gear to the wing steadily.
73 Adjustment. 11 Install the nylon control horn and connect the linkage.
13 Mount the gear door and the wheel to the retract.
Wheel (100mm)
Retainer Bushing (8X4mm)
Rod (2x300mm)
Clevis
RUDDER
Screw (2x10mm)
40mm
40mm
Note:rubber wheels oleo struts
and retracts are optional.
Top view
TP Screw (2.3x12mm)
Collar (5mm)
TP Screw (2.3x12mm)
8
1.5mm 5mm
Top view
Collar (5mm) Rod (2x300mm)
ELEVATOR
Clevis
30mm
3mm Screw (2x10mm)
30mm Lock Nut (3mm )
Washer(3x15mm)
14 3
16 Epoxy the wheel house to the wings carefully.
19 According to the rib template drill holes in one wing and
epoxy wood dowel in them. 65 Epoxy plies to relevant position inside the fuselage as
below for assembling the cowling. 68 Epoxy the exhaust to appropriate position in the
fuselage as illustration.
TP Screw (2.3x8mm)
Rib template (2mm ply)
1
Wood dowel (6x30mm)
2
Main wing joiner
1 1.5mm
6mm
Rib template (2mm ply)
TP Screw (2.3x8mm)
6
Wood dowel (6x30mm) Pvc part
Note:Please fix the air tube before Ply (15x15x3mm)
6 2
assemble the wheel house to the wing.
100mm
A A` Wooden Block
For servo wire R10mm
30mm TP Screw (2.3x8mm)
1.5mm 8 Wooden supporter
Ply (15x15x3mm)
A=A' 8
4 13
60 Install the servo.
63 The servos installation finished sketch map.
22 Epoxy the main wing hardly together with wing joiner.
25 Assemble the wings to the fuselage with screw
and blind nut as below.
Clevis
2
Copper joiner switch servo
2
Screw (2x10mm) Reinforcement Plate
2 Screw(6x50mm)
Nut (2mm ) 2
2 Blind Nut (6mm)
Washer(2x5mm) 2
2 Rudder servo Securely glue together. If coming off during flights, you 'll Reinforcement Plate
lose control of your airplane which leads to accidents! 1
61 Mount the servo of nose wheel to the fuselage. Accessory list for the coming installation steps.
23 Drill holes to appropriate position in the front of mid
wing and epoxy wood dowel in them.
Accessory list for the coming installation steps.
6mm 11mm
80mm
12 5
27 The side sketch map of the engine installation finished.
30 Assemble the accelerator push rod to the engine. 55 Install the rudder servo to appropriate position
in the fuselage. 58 Assemble the wheel and oleo strut to
the retract as illustration.
Washer (2mm)
1 Brass collar (5mm)
Washer(4x8mm)
162 mm Washer (4x8mm) Screw (4x25mm)
Rod (2x650mm) 4
Washer(4x8mm)
Set Screw (2mm) Note:rubber wheels oleo struts
1
and retracts are optional.
Screw (4x25mm)
Set Screw (3x4mm) 2
1 Steering fullarm (60x6mm) Washer(4x8mm)
2
Aluminum shaft(5x50mm)
1
Steering fullarm (60x6mm)
1
Set Screw (2mm) Wheel (75 mm)
1
Collar (5mm)
2
TP Screw(3x20mm)
Elevator servo
5.2mm
1.8mm
Rudder servo
Blind Nut
TP Screw(3x20mm)
Blind Nut (4mm) 4
4
Screw (4x35mm)
Washer (4x8mm)
wheel (90mm) Steel wire (0.5x1500mm)
1 2
Bushing (8X4mm) Clevis
2 2
Lock Nut (4mm ) 2 Copper joiner
2
TP Screw(3x20mm)
4mm Air tank
4 Screw (2x10mm)
2
1 Nut (2mm )
Switch 2
1
Washer(2x5mm)
Clevis 2
Washer (4x8mm) 1
Rod (2x300mm)
Air pressure line 1
Fuel spray line Retainer
Washer (4x8mm)
Screw (4x25mm)
1
Spring Washer (4mm) Fuel supply line
Nut (4mm)
6 11
49 Keep some space about 1mm width between
the tailing edge and the rudder. 52 The sketch map after the rudder shaft assemble finished. 33 Mount the fuel tank to the fuselage. Accessory list for the coming installation steps.
Pin hinge(24x24mm) 6
Tailing U-style wire (150x25mm)
edge 1
Steel wire (0.5x3000mm) 2
Cut away the rubber tube when
the epoxy glue dried. Matal douel (4x30mm) 4
Rudder
Lock Nut (3mm ) Rib template (2mm ply) 1
Stab joiner (12x310mm)
Steel wire 1
Screw (3x80mm) Clevis
2
Aluminum tube Copper joiner
Washer(3x15mm) 2
1mm Screw (2x10mm)
Clevis 2
Nut (2mm )
Clevis Screw (3x80mm) 2
2 1 Washer(2x5mm)
Washer(3x15mm) Copper joiner 2 Note: Customers can choose nylon stabbing fix the tank, 2
Make sure they are in 2
the right position while Lock Nut (3mm ) 2 Steel wire (0.5x3000mm) We don’t suppty nylon stabbing. Plastical tube(3x30mm)
installing.
2 2
51 54 35 37
Drill a small hole to appropriate position in the fuselage Assemble the throttle servo to appropriate
for installing the plastical tube and a hole in the rudder Install the servo. Set the U-style wire through the enlargd hole as below.
position in the fuselage.
for assembling the rudder shaft.
Steel wire
3mm
Clevis
75mm 90mm 2
Copper joiner
2
30mm Screw (2x10mm)
Steel wire (0.5x3000mm)
2
Nut (2mm ) 2
2
U-style wire (150x3mm)
Washer(2x5mm) 1
2
10 7
38 According to the rib template drill holes to the tail of
fuselage and assemble the "U"style wire as illustration. 41 Trim slot to appropriate position in the stabilizer .
44 Glue the elevator to the stabilizer by CA and epoxy.
47 Connect the elevator and the serer via the steel wire.
1x20mm
4mm
Rib template (2mm ply)
Elevator servo
Stab joiner (12x310mm)
39 Drill two holes at the stabilizer root base via rib template
and epoxy the wood dowel in them. 42 Apply instant type CA glue to elevator and pin hinge.
45 Install the servo. Accessory list for the coming installation steps.
Tailing
edge
2.5mm
Elevator 30mm
80mm
1mm 25mm
8 9