Professional Documents
Culture Documents
Workzone GT-UDM-02 Manual en
Workzone GT-UDM-02 Manual en
DISTANCE MEASURER
Instruction Manual
03 Warranty details
04 Introduction
05 Proper use
06 Safety advice
09 Additional safety advice for lasers
10 Disposal of device
10 Battery instructions Ultrasonic Distance Measurer
11 List of contens
12 Description of parts / scope of delivery
14 Operation Warranty Details
14 Insert battery
14 Displays The product is guaranteed to be free from defects in workmanship and
15 Avoiding measurement errors parts for a period of 12 months (dependant on product) from the date
17 Distance measurement of purchase. Defects that occur within this warranty period, under nor-
18 Addition (without M+storage) mal use and care, will be repaired, replaced or refunded at our discre-
19 Addition (with M+storage) tion. The benefits conferred by this warranty are in addition to all rights
20 Area and remedies in respect of the product that the consumer has under the
22 Area addition in area mode Competition and Consumer Act 2010 and similar state and territory laws.
23 Volume
Our goods come with guarantees that cannot be excluded under the
25 Volume addition in volume mode
Australian Consumer Law. You are entitled to a replacement or refund
26 Temperature display
for a major failure and for compensation for any other reasonably
27 Battery display
foreseeable loss or damage. You are also entitled to have the goods
27 Switching off the device
repaired or replaced if the goods fail to be of acceptable quality and the
28 Cleaning
failure does not amount to a major failure.
28 Storage
28 Disposal of device
29 Technical data
We congratulate you on your new ultrasound distance measurer The electronic multi-measurement device GT-UDM-02 deter-
and are convinced that you will be satisfied with this state-of-the-art mines the distance of an object through electronically generated
device. The device conforms to the relevant safety regulations. high-speed signals. The measurement result can be read off of the
In order to guarantee that this device will always function and display. The device has a computer chip and a key indicator and
perform and in order to ensure your personal safety, please read memory function, can be used for automatic area calculation and
through these instructions before using the device and, above all, volume counting and is an ideal device for the construction and fur-
follow the safety advice! All activities carried out on and with this nishing industry (e.g. property brokers, furniture designers and crafts-
device are only permitted to be carried out to the extent that they men, etc.).
have been described in these operating instructions. The device has a laser orientation function, i.e. it emits a red laser
If you should pass this ultrasound distance measurer on, please beam with which it can easily aim at an object during use. The
include these instructions. automatic temperature comparison of the device provides a more
precise measurement result and indicates the exact environmental
Packaging temperature at the same time.
Packaging is for protection from transport damage. Packaging
consists of raw materials that can be reused or returned to the raw
materials circuit.
Remove all parts from the packaging before operating the device.
The electronic multi-measurement device GT-UDM-02 is a class II laser Take environmental influences into consideration!
device and conforms with international safety guidelines 21CFR Do not expose the device to rain. Do not use the device in a damp
1040.10, 1040.11 and EN 60825-1:2007 or wet environment. Ensure that your work area is well lit. Do not
Do not remove the labels from the device. use the device in locations where there is a risk of fire or explosion,
e.g. near flammable liquids or gases.
eyes of another person. Do not look at the laser beam with binocu- Additional safety advice for lasers
lars or a magnifying glass.
Use the correct device!
The proper use is described in these operating instructions. Caution! Laser beams!
Warning! The use of attachment devices or accessories other than
those recommended in these instructions or carrying out work with Do not look into the laser beam.
this device that is not in accordance with proper use can lead to risk
of accidents. Do not look at the laser beam with optical instruments
Check your device for damage!
Do not drop the device. Check the device for damage before • This laser complies with class 2 according to EN 60825-1:2007.
starting work. • Do not exchange the laser diode for another type. Have a defective
Ensure that the device functions properly. Do not use the device if a laser repaired by a customer service workshop.
part is defective. • Only use the laser for aiming.
Keep your devices in a safe place! • Never look directly/intentionally into the laser beam.
Unused devices and batteries are to be stored in a dry place that is • Do not use any optical devices to look at the laser beam.
not accessible for children. • Do not set up the tool in such a position that the laser beam could
Repairs: cross people at head level.
This device complies with the respective safety guidelines. Repairs • Do not allow children near the laser.
are only to be carried out by authorised specialists and with original
replacement parts.
Please also note the following:
Not using the device according to these operating
instructions, could void your warranty.
Disposal of device • Avoid contact with skin, eyes and mucous membranes. Upon
Please dispose of this product and battery responsibly at contact with battery acid, rinse the affected areas with plenty of
end of life. Do not throw away with household waste. Please clear water and immediately call on a doctor.
contact your retailer or local authority for details of recycling • Remove dead batteries from the device and dispose of them
schemes operating in your area. responsibly. Replace with a suitable new 9V battery.
1. Ultrasound transmitter/receiver 10. Measurement reference --- The distance can be calculated from
2. Direction-finding laser the baseline or the top of the device. By pressing the BASE
3. Double row LCD display key the measurement reference can be switched.
The data in the top row show the current measurement result – Battery compartment on reverse (not shown)
and the data in the bottom row show the memory/calculation – 9 V block battery, size 6F22 (not shown)
result 2 1
4. BASE – The distance measurement can be calculated from two
points. Pressing the BASE key can set the distance measurement 10
between the baseline and top of the device.
5. FT/M – Push this button lightly in order to switch between
metres and feet. Keep the button pressed down for approx. 2
seconds in order to display the environmental temperature.
6. MODE – Push this button briefly in order to delete the measure-
ment or return to the menu, in order to change over to the 3
length, area or volume mode. Keep the button pressed down
for approx. 2 seconds, in order to save the length, area or volu- 4
me measurement. 5 7
7. +/= - Press this button lightly in order to add the measured
6 8
length, area or volume. Keep the button pressed down for
approx. 2 seconds, in order to read and display the last saved
length, area or volume value.
9
8. READ – Press this button in order to start the measurement.
Keep the button pressed down and move the device during the
measurement process so that dynamic values can be read off.
9. Spirit level
10
A) Plus
B) Length/area/volume L=length W=width H=height
C) Measurement display from where the device measures. • If the measured result is outside of the indicated area: The error
D) Memory message “Err” is shown in the bottom row of the display.
E) Memory, calculation result
F) Current measurement result
G) Displayed with insufficient power supply
H) square foot 8. With the addition of various parameters (e.g. length plus area), the
I) Cubic foot “+” is ignored and the display shows the same result as the previous
J) Metre / square metre / cubic metre measurement.
Tips: • Press the READ button again in order to carry out a second mea-
A. The measured object should have a hard surface and not be blocked by surement – the measurement value appears in the upper section of
obstacles; the display;
B. In order to obtain precise results, select a large, smooth, hard surface;
C. If the measured surface is too small, irregular or too soft, chipboard
can be used on the surface of the measured object;
D. This device can not be used to measure through glass; • Press the +/= button again in order to display the sum in the bottom
E. The device should be further than 60 cm away from the measured section of the display;
object during measurement;
F. In order to achieve a more precise measurement result, the temperature
of the device should correspond to the environmental temperature.
• By repeating the above steps, the addition is continued.
Addition (without M+storage)
• Press the READ button – the measurement value appears in the Addition (with M+storage)
upper section of the display; • Carry out the measurement. Save the final result by keeping the
MODE button pressed for at least 2 sec., until a double beeping
tone sounds. “M+“ will appear in the display.
• Press the +/= button in order to enter the addition mode – the “+”
symbol appears in the display and the result will be shown in the
bottom section of the display at the same time (press the +/= button • Start new measurement as described - press the READ button;
again in order to stop the addition);
• Press the +/= button in order to switch into the addition mode – “+”
will appear in the display;
• Adding memory to last measurement result: Press +/= for at least • The width symbol “W“ in the display flashes and shows the next
2 sec. until a double beeping tone sounds. “M” will disappear from the measurement to be carried out. Press the READ button in order to
display. Only the saved value will be shown in the bottom of the display. obtain the width measurement, which is shown in the upper section
of the display (Step 2);
The area is automatically shown in the lower section of the display;
• Press the +/= button briefly – the result of the last measurement +
saved measurement will appear in the display.
• Pressing the READ button again switches back and forth between
length and width in the upper section of the display;
− Press the MODE button in order to delete the data from the
Area display – now a new area calculation can be carried out.
• Press the MODE button in order to switch into the area mode and − In order to switch the measurement mode, press the MODE button
appears to calculate the area of a space; again;
Tips:
With single pressing of the MODE button, you can switch back and
forth between the length, area and volume. If there is data available
• The length symbol “L“ in the display flashes and show the first mea- in the display, pressing the MODE button will delete the current
surement that you have carried out. Press the READ button in order data – the mode remains unchanged.
to obtain the length measurement, which is shown in the upper section
of the display (Step 1);
Area addition in the area mode: • Press the +/= button – the sum of both areas appears in the bottom
• Keep the MODE button pressed down in order to save the calcu- section of the display;
lated area from the first measurement; at the same time, the “M+”
symbol appears on the display. A double beeping tone will sound;
• After obtaining the desired area from the second calculation, press
+/= in order to switch into the addition mode. The “+“ symbol • The length symbol “L“ in the display flashes to indicate that the
appears in the display. length measurement is taking place. Press the READ button in order
to measure the length, the result appears in the upper section of the
display. (Step 1)
• The width symbol “W“ in the display flashes to indicate the next Volume addition in the volume mode:
measurement to be carried out. Press the READ button in order to • Press the MODE button in order to store the calculated volume
measure the width, the result appears in the upper section of the from the first measurement – the “M+“ symbol appears in the display;
display. (Step 2);
• Press the +/= button – the sum of both volumes will appear in the Battery display
lower section of the display; Empty battery: Here, the symbol constantly appears in the display
in order to remind you to change the battery.