Professional Documents
Culture Documents
Спецификация Toshiba LTM015A83B
Спецификация Toshiba LTM015A83B
FEATURES
(1) a-Si TFT-LCD
(2) 176(H) x 132(V) pixels TENTATIVE
(3) Transfletive type Mode (Normally White)
(4) 65,536/262,144 colors
(5) CPU memory bus I/F(8bit)
(6) Cell + FPC + Backlight
MECHANICAL SPECIFICATIONS
Item Specifications
Dimensional Outline (TYP.) 35.07(W) x 31.48(H) x 1.98(D) mm(Typ.)
Number of Pixels 176(x RGB)(W) x 132 (H) pixels
Active Area 29.568 (W) x 22.176 (H) mm
Pixel Pitch 0.168(W) x 0.168(H)
Weight (approximately) (TBD) g(Typ.)
ABSOLUTE MAXIMUM RATINGS
Item Min. Max. Unit Remarks
LED Forward Direction Current - 35 mA Per piece of LED
LED DC Reverse Withstand Voltage - 5 V Per piece of LED
LED Permissible Loss - 123 mW Per piece of LED
LED Peak Pulse Forward Direction Current - 100 mA Per piece of LED
Pulse width≦10ms, Duty
ratio≦1/10
Logic Power Supply -0.3 4.0 V
Operating Temperature -10 60 °C
Storage Temperature -30 70 °C
Storage Humidity (Max. wet bulb temp. = 39°C) 10 90 %(RH)
ELECTRICAL SPECIFICATION
Item Min. Typ. Max. Unit Remarks
Supply Voltage(VCI) 2.8 3.0 3.2 V *1
Supply Voltage(VDDIO) 2.7 3.3 3.6 V *1
LED forward Voltage --- (3.2) 3.5 V If=20mA, Per piece of LED
Power Consumption --- TBD TBD mW *1 Norm al mode Backlight on
*1 : Final number well be specified with actual LCD samples
OPTICAL SPECIFICATION (Ta=25°C)
Item Min. Typ. Max. Unit Remarks
Contrast Ratio (CR) 100 140 --- --- *2 Transmissive mode
Response Time (tON) --- 15 20 ms *2 Transmissive mode
(tOFF) --- 25 35 ms *2 Transmissive mode
2
Brightness*3 200 270 --- cd/m *2 *3 Transmissive m ode
Reflectance*4 (5.5) --- --- % *2
NTSC ratio --- (33) --- % *2 Transmissive mode
Optimum view angle --- 4:30 o’clock --- ---
*2 : Final number will be specified with actual LCD samples
*3 : LED Power=20mA×2LED
*4 : Diffuse Reflectance (SCE Mode)
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Matsushita Display Technology Co.,Ltd. or other rights of the third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology Co.,Ltd. or others.
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display
Technology Co.,Ltd. before proceeding with the design of equipment incorporating this product.
<Block diagram>
RGB
Back Light
176 x 132 pixels
LED
GRAM
DC/DC Vcom
Converter Panel
Gray scale
Controller Manipulation
Voltage
Generation
Circuit
D[0:7]
LED+
VEE
RES
LED-
VDD
FLM
VSS
WR
RD
CS
RS
0.3mm Pitch
Block A: Power On
Block B: Initialize
Block E2: Display Off Block E1: Display Off Block G: Set Standby
Block A: Power On
Step Register Setting Operation
1 Power On (VEE → VDD or VEE, VDD Simultaneously)
2 Delay 10ms
3 RESET=L
4 Delay 1ms
5 RESET=H
6 Delay 3ms
7 0000 -
8 0000 -
9 0000 -
10 0000 -
11 Delay 10ms
Block B: Initialize
Step Register Setting Operation
1 00A4 0001 CALB=”1”
2 Delay 150ms
3 0001 0100 SM=”0”,SS=”1”
4 0002 0300 BC=”1”,EOR=”1”
TRI : 65k colors=”0”
1230
5 0003 260k colors=”1”,
(9230)
BGR=”1”,HWM=”1”,ID=”11”,AM=”0”
6 0008 0404 FP=”0100”,BP=”0100”
7 000E 0010 VEM=”1”
8 0070 1000 GS=”0”,NL=”10000”,SCN=”00000”
9 0071 0001 REV=”1”
10 0030 0002 Gamma control 1
11 0031 0400 Gamma control 2
12 0032 0007 Gamma control 3
13 0033 0500 Gamma control 4
14 0034 0007 Gamma control 5
15 0035 0703 Gamma control 6
16 0036 0507 Gamma control 7
17 0037 0005 Gamma control 8
<Mating Connector>
FF12-22A-R11A or FF12-22A-R11B (DDK)
<Command/AC Timing>
Detail technical information of “command/data”, or “AC timing” can be available with following documents:
-IC specification of one-chip controller driver IC : R69501 (RENESAS)
About the method of driving LED, please consider the content of specifications of LED and LED-Dr
enough.
Warning
1) SPECIAL PURPOSES
a) Toshiba Matsushita Display Technology’s Standard LCD modules have not been customized for operation in extreme
environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.
b) Since they have not been designed for operation in extreme environments, they must never be used in devices that will
be exposed to temperatures above 50 degrees Celsius or below 0 degrees Celsius, to X-ray or Gamma-ray radiation,
or to abnormally high levels of vibration or shock which exceed Toshiba Matsushita Display Technology’s specification
limits.
c) In addition, since Toshiba Matsushita Display Technology’s Standard LCD modules have not been designed for use in
applications where performance failures could be life-threatening of catastrophic, they must never be installed in aircraft
navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in
military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production
of nuclear energy), or in critical medical device or patient life-support systems.
Caution
* 1) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the modules.
Sensitive parts inside LCD module may be damaged, and dusts or scratches may mar the displays. Toshiba Matsushita
Display Technology does not warrant the modules, if customer disassembled or modified them.
* 2) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT PERMIT this material to contact
the skin, if glass of LCD panel is broken. If liquid crystal material contacts the skin, mouth or clothing, take the following
actions immediately. In case contact to the eye or mouth, rinse with large amount of running water for more than 15
minutes. In case contact to the skin or clothing, wipe it off immediately and wash with soap and large amount of running
water for more than 15 minutes. The skin or closing may be damaged if liquid crystal material is left adhered. In case
ingestion, rinse out the mouth well with water. After spewing up by drinking large amount of water, get medical
treatment.
* 3) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GRASS that may cause injuring fingers or skin, when the glass is broken.
4) ABSOLUTE MAXIMUM RATINGS
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply
voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD
module may be damaged.
5) POWER PROTECTION CIRCUIT
Employ protection circuit for power supply, whenever the specification specifies it. A suitable protection circuit should be
applied, based on each system design. A fuse is not fitted to this module. Therefore, without a suitable power-supply
protection device, dust or partial circuit failure may cause overheating and/or burning , which may lead to injury.
6) DISPOSAL
Always comply with all applicable environmental regulations, when disposing of the LCD.
7) EDGES OF PARTS
Be careful with edges of glass parts, it may cause injuring.
For designing the system, give special consideration that the wiring and parts do not touch those edges.
<Revision History>