Professional Documents
Culture Documents
Warning Chime System: Section
Warning Chime System: Section
Warning Chime System: Section
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
BASIC INSPECTION .................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................10
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 PARKING BRAKE RELEASE WARNING CHIME
Work Flow ................................................................. 3 : Component Parts Location ....................................11 G
PARKING BRAKE RELEASE WARNING CHIME
FUNCTION DIAGNOSIS ............................... 4 : Component Description .........................................12
WARNING CHIME SYSTEM ............................... 4 DIAGNOSIS SYSTEM (METER) ....................... 13 H
Diagnosis Description ..............................................13
WARNING CHIME SYSTEM ....................................... 4
CONSULT-III Function (METER/M&A) ....................13
WARNING CHIME SYSTEM : System Diagram ...... 4
WARNING CHIME SYSTEM : System Description I
DIAGNOSIS SYSTEM (BCM) ........................... 16
...... 4
WARNING CHIME SYSTEM : Component Parts BUZZER .....................................................................16
Location ..................................................................... 5 BUZZER : CONSULT-III Function ...........................16 J
WARNING CHIME SYSTEM : Component De-
scription ..................................................................... 6 COMPONENT DIAGNOSIS ......................... 17
LIGHT REMINDER WARNING CHIME ....................... 6 POWER SUPPLY AND GROUND CIRCUIT .... 17 K
LIGHT REMINDER WARNING CHIME : System
COMBINATION METER ............................................17
Diagram ..................................................................... 6
COMBINATION METER : Diagnosis Procedure ....17 L
LIGHT REMINDER WARNING CHIME : System
Description ................................................................ 6 BCM (BODY CONTROL MODULE) ..........................18
LIGHT REMINDER WARNING CHIME : Compo- BCM (BODY CONTROL MODULE) : Diagnosis
nent Parts Location ................................................... 7 Procedure ................................................................18 M
LIGHT REMINDER WARNING CHIME : Compo- BCM (BODY CONTROL MODULE) : Special Re-
nent Description ........................................................ 7 pair Requirement .....................................................18
SEAT BELT WARNING CHIME .................................. 8 WCS
METER BUZZER CIRCUIT ............................... 20
SEAT BELT WARNING CHIME : System Diagram Description ...............................................................20
...... 8 Component Function Check ....................................20
SEAT BELT WARNING CHIME : System Descrip- Diagnosis Procedure ..............................................20 O
tion ............................................................................ 8
SEAT BELT WARNING CHIME : Component SEAT BELT BUCKLE SWITCH SIGNAL CIR-
Parts Location ........................................................... 9 CUIT .................................................................. 21 P
SEAT BELT WARNING CHIME : Component De- Description ...............................................................21
scription ................................................................... 10 Component Function Check ..................................21
Diagnosis Procedure ..............................................21
PARKING BRAKE RELEASE WARNING CHIME .... 10
Component Inspection .............................................22
PARKING BRAKE RELEASE WARNING CHIME
: System Diagram .................................................... 10 ECU DIAGNOSIS ......................................... 23
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM C
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
D
>> GO TO 2
2.CHECK SYMPTOM E
• Check the symptom based on the information obtained from the customer.
• Check to see if any other malfunctions are present.
F
>> GO TO 3
3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS G
Connect CONSULT-III and perform “SELF-DIAGNOSIS”. Refer to MWI-42, "CONSULT-III Function (METER/
M&A)".
Are self-diagnosis results normal? H
YES >> GO TO 4
NO >> Repair or replace the malfunctioning parts, GO TO 5
4.NARROW DOWN MALFUNCTIONING PARTS THROUGH SYMPTOM DIAGNOSIS I
Perform symptom diagnosis and repair or replace the identified malfunctioning parts.
J
>> GO TO 5
5.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally. K
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 1 L
WCS
AWNIA0290GB
COMBINATION METER
• The buzzer (1) for warning chime system is installed in the combi-
nation meter.
• The buzzer sounds when the combination meter receives a buzzer
output signal from each unit.
AWNIA0063ZZ
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter with
CAN communication line if it judges that the warning buzzer should be activated.
BCM warning function list
Warning functions Signal name
• Lighting switch position signal
Light reminder warning chime
• Door switch signal
Seat belt warning chime Seat belt buckle switch signal
ALNIA1068ZZ
1. Combination meter M24 2. Combination switch (lighting switch) 3. Seat belt buckle switch LH B202 M
M28
4. Door switch LH B68 (coupe) 5. BCM M16, M17, M18, M19 (view with 6. ABS actuator and electric unit (control
Door switch LH B8 (sedan) instrument panel removed) unit) WCS
E54 (with VDC)
E26 (without VDC)
7. Parking brake switch M73 (sedan with 8. Parking brake switch E35 (sedan with
M/T or coupe) (view with center con- CVT) [view with instrument panel low- O
sole removed) er cover (LH) removed]
Unit Description
• Judges whether the parking brake is released using the vehicle speed signal and the parking
brake switch signal, and sounds the buzzer if necessary.
Combination meter • Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM with CAN communication line.
• Receives a buzzer output signal from BCM with CAN communication line.
Transmits signals provided by various units to the combination meter with CAN communication
BCM
line.
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter with CAN communication line.
(control unit)
Seat belt buckle switch LH Transmits a seat belt buckle switch signal to the combination meter.
Combination switch
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Door switch LH Transmits the door switch signal to BCM.
Parking brake switch Transmits parking brake signal to combination meter.
AWNIA0292GB
DESCRIPTION
With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1ST or 2ND position, the
light warning chime will sound.
• BCM detects ignition switch in OFF or ACC position, door switch LH ON, and lighting switch in 1ST or 2ND
position. And then transmits buzzer output signal (light reminder warning chime) to combination meter with
CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled
• Lighting switch is at 1st or 2nd position
• Ignition switch is at OFF or ACC
• Door switch LH is ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF
• Ignition switch ON
• Door switch LH is OFF
ALNIA1068ZZ
1. Combination meter M24 2. Combination switch (lighting switch) 3. Seat belt buckle switch LH B202 M
M28
4. Door switch LH B68 (coupe) 5. BCM M16, M17, M18, M19 (view with 6. ABS actuator and electric unit (control
Door switch LH B8 (sedan) instrument panel removed) unit) WCS
E54 (with VDC)
E26 (without VDC)
7. Parking brake switch M73 (sedan with 8. Parking brake switch E35 (sedan with
M/T or coupe) (view with center con- CVT) [view with instrument panel low- O
sole removed) er cover (LH) removed]
Unit Description
Combination meter Receives a buzzer output signal from BCM via CAN communication line and sounds the buzzer.
Judges the light warning conditions from the signals provided by various switches and transmits a
BCM
buzzer output signal to the combination meter via CAN communication line if necessary.
LKIA0878E
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds.
• BCM receives seat belt buckle switch signal from combination meter with CAN communication line.
• BCM detects ignition switch turned ON and seat belt buckle switch LH ON. And then transmits buzzer output
signal (seat belt warning chime) to combination meter with CAN communication line.
• When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled
• Ignition switch OFF→ON
• Seat buckle switch LH is ON (driver seat belt not fastened)
WARNING CANCEL CONDITIONS
Cancels the warning if any of the following conditions is fulfilled.
• Ignition switch OFF
• Seat buckle switch LH is OFF (driver seat belt fastened)
• 90 seconds have passed since the start of the warning
ALNIA1068ZZ
1. Combination meter M24 2. Combination switch (lighting switch) 3. Seat belt buckle switch LH B202 M
M28
4. Door switch LH B68 (coupe) 5. BCM M16, M17, M18, M19 (view with 6. ABS actuator and electric unit (control
Door switch LH B8 (sedan) instrument panel removed) unit) WCS
E54 (with VDC)
E26 (without VDC)
7. Parking brake switch M73 (sedan with 8. Parking brake switch E35 (sedan with
M/T or coupe) (view with center con- CVT) [view with instrument panel low- O
sole removed) er cover (LH) removed]
Unit Description
• Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
Combination meter BCM via CAN communication line.
• Receives a buzzer output signal from BCM via CAN communication line and sounds the buzzer.
Judges the seat belt warning condition from the seat belt buckle switch signal received from the
BCM combination meter and transmits a buzzer output signal to the combination meter via CAN commu-
nication line if necessary.
Seat belt buckle switch LH Transmits seat belt buckle switch signal to combination meter.
AWNIA0263GB
DESCRIPTION
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication line.
• The combination meter judges whether the parking brake is released using the parking brake switch signal
from the parking brake switch, and sounds the warning buzzer if necessary.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled
• Vehicle speed is approximately 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
ALNIA1068ZZ
M
1. Combination meter M24 2. Combination switch (lighting switch) 3. Seat belt buckle switch LH B202
M28
4. Door switch LH B68 (coupe) 5. BCM M16, M17, M18, M19 (view with 6. ABS actuator and electric unit (control WCS
Door switch LH B8 (sedan) instrument panel removed) unit)
E54 (with VDC)
E26 (without VDC)
7. Parking brake switch M73 (sedan with 8. Parking brake switch E35 (sedan with O
M/T or coupe) (view with center con- CVT) [view with instrument panel low-
sole removed) er cover (LH) removed]
P
Unit Description
• Judges whether the parking brake is released using the parking brake switch signal from the
parking brake switch, and sounds the buzzer if necessary.
Combination meter
• Receives a vehicle speed signal from ABS actuator and electric unit (control unit) via CAN
communication line.
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter via CAN communication line.
(control unit)
Parking brake switch Transmits parking brake switch signal to the combination meter.
SELF-DIAGNOSIS MODE B
• Odo/trip meter and information display segment operation can be checked in self-diagnosis mode.
• Meters/gauges can be checked in self-diagnosis mode.
OPERATION PROCEDURE C
1. Turn the ignition switch OFF.
2. While pushing the odo/trip meter switch, turn the ignition switch ON again.
D
3. Push the odo/trip meter switch at least 3 times within 7 seconds after the ignition switch is turned ON.
4. The unified meter control unit is turned to self-diagnosis mode.
• All the segments on the odo/trip meter illuminate.
E
SKIB1206J
H
JSNIA0020GB
L
5. Push the odo/trip meter switch. Each meter/gauge should indicate as shown in the figure.
WCS
AWNIA2160ZZ
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF-DIAG RESULTS
Display Item List
Refer to WCS-25, "DTC Index".
DATA MONITOR
Display Item List
X: Applicable
MAIN SELECTION
Display item [Unit] Description
SIGNALS FROM MENU
SPEED METER [km/h] or [mph] X X Displays the value of vehicle speed signal.
Displays the value of vehicle speed signal, which is transmitted to
SPEED OUTPUT [km/h] or [mph] X X
each unit with CAN communication.
ODO OUTPUT X Displays the value, which is calculated by vehicle speed signal.
TACHO METER [rpm] X X Displays the value of engine speed signal, which is input from ECM.
Displays the value, which processes a resistance signal from fuel
FUEL METER [lit.] X X
gauge.
Displays the value of engine coolant temperature signal, which is in-
W TEMP METER [°C] or [°F] X X
put from ECM.
ABS W/L [ON/OFF] X Displays [ON/OFF] condition of ABS warning lamp.
VDC/TCS IND [ON/OFF] X Displays [ON/OFF] condition of VDC OFF indicator lamp.
SLIP IND [ON/OFF] X Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Displays [ON/OFF] condition of brake warning lamp.*
DOOR W/L [ON/OFF] X Displays [ON/OFF] condition of door warning lamp.
TRUNK/GLAS-H [ON/OFF] X Displays [ON/OFF] condition of trunk warning lamp.
HI-BEAM IND [ON/OFF] X Displays [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF] X Displays [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Displays [ON/OFF] condition of oil pressure warning lamp.
MIL [ON/OFF] X Displays [ON/OFF] condition of malfunction indicator lamp.
CRUISE IND [ON/OFF] X Displays [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF] X Displays [ON/OFF] condition of SET indicator.
ATC/T-AMT W/L [ON/OFF] X Displays [ON/OFF] condition of AT CHECK warning lamp.
FUEL W/L [ON/OFF] X Displays [ON/OFF] condition of low-fuel warning lamp.
WASHER W/L [ON/OFF] X Displays [ON/OFF] condition of low-washer fluid warning lamp.
AIR PRES W/L [ON/OFF] X Displays [ON/OFF] condition of tire pressure warning lamp.
KEY G/Y W/L [ON/OFF] X Displays [ON/OFF] condition of key warning lamp.
LCD X Displays the value of Intelligent Key system message indication.
SHIFT IND [P, R, N, D, L] X Displays [P, R, N, D, L] range position of CVT.
M RANGE SW [ON/OFF] X Displays [ON/OFF] condition of manual mode range switch.
Displays [ON/OFF] condition of except for manual mode range
NM RANGE SW [ON/OFF] X
switch.
AT SFT UP SW [ON/OFF] X Displays [ON/OFF] condition of CVT shift-up switch.
AT SFT DWN SW [ON/OFF] X Displays [ON/OFF] condition of CVT shift-down switch.
WCS
DATA MONITOR
Display item
Description
[Unit]
PUSH SW
Status of push button ignition switch judged by BCM.
[On/Off]
UNLK SEN -DR
Status of door lock assembly (door unlock sensor) judged by BCM.
[On/Off]
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN
[mph] communication line.
KEY SW-SLOT
Status of key slot judged by BCM.
[On/Off]
TAIL LAMP SW
Status of each switch judged by BCM using the combination SW readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM.
[On/Off]
DOOR SW -DR
Status of driver side door switch judged by BCM.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
C
Regarding Wiring Diagram information, refer to MWI-106, "COUPE : Wiring Diagram" (coupe) or MWI-124,
"SEDAN : Wiring Diagram" (sedan).
D
1.CHECK FUSES
Check for blown combination meter fuses. E
Terminals
(+) Continuity P
(–)
Connector Terminal
3
M24 4 Ground Yes
AWNIA1767ZZ
23
Is the inspection result normal?
Regarding Wiring Diagram information, refer to BCS-75, "COUPE : Wiring Diagram" or BCS-84, "SEDAN :
Wiring Diagram".
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M16 1
Battery voltage ALCIA0025ZZ
M17 11
Is the measurement normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M17 13 Yes
Does continuity exist?
YES >> Inspection End.
NO >> Repair or replace harness.
ALCIA0024ZZ
WCS
• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000005432763
BUCKLE SW D
When seat belt is fastened : OFF
When seat belt is unfastened : ON E
G
Regarding Wiring Diagram information, refer to WCS-55, "COUPE : Wiring Diagram-Coupe" or WCS-61,
"SEDAN : Wiring Diagram-Sedan".
H
1. CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector M24 terminal 35 and ground. I
35 - Ground
When driver seat belt is fastened : Approx. 12V J
When driver seat belt is unfastened : Approx. 0V
Is the inspection result normal? K
YES >> Replace combination meter. Refer to MWI-153, "Removal and Installation".
NO >> GO TO 2
2. CHECK SEAT BELT BUCKLE SWITCH CIRCUIT L
1. Turn ignition switch OFF.
2. Disconnect combination meter and seat belt buckle switch LH.s
3. Check continuity between combination meter harness connector M24 terminal 35 and seat belt buckle M
switch LH harness connector B202 terminal 1.
AWNIA0087ZZ
1– 2
When seat belt is : Continuity should not exist.
fastened
When seat belt is : Continuity should exist.
unfastened
Is the inspection result normal? WKIA1143E
TERMINAL LAYOUT
C
AWNIA1773ZZ
PHYSICAL VALUES F
Condition
Termi- Wire Reference value (V)
nal color
Item Ignition (Approx.)
G
Operation or condition
switch
1 W/L Battery power supply — — Battery voltage
Ignition switch ON or
H
2 O ON — Battery voltage
START
3 B Ground (Power)
— — 0 I
4 B Ground (Illumination)
5 R/Y Illumination output — —
Illumination switch pow- Refer to INL-10, "System Description".
9 GR/W — — J
er
10 O/L Mode switch ground ON — 0
Switch pressed 0 K
11 L/R Mode switch A ON
Switch released 5
Switch pressed 0
12 B/R Mode switch B ON L
Switch released 5
Ignition switch ACC or
14 V/Y ON — Battery voltage
ON
M
Air bag warning lamp in- Air bag warning lamp ON 3
15 BR/W ON
put Air bag warning lamp OFF 0
WCS
At idle [after warming up,
approx. 80°C (176°F)]
Water temperature out- NOTE:
16 G/W ON O
put The wave forms vary de-
pending on coolant tem-
perature.
SJIA1438J P
Signal ON 0
17 R/W AC PD CUT ON
Signal OFF 5
18 O/B Ambient sensor signal ON — 0 - 5 (Based on ambient temperature)
19 P Ambient sensor VDD ON — 5
20 B/Y Ambient sensor ground ON — 0
Speedometer operated
Vehicle speed signal out-
31 V/W ON [When vehicle speed is ap-
put (8-pulse)
prox. 40 km/h (25 MPH)]
PKIC0643E
A
The combination meter performs a fail-safe operation for the functions listed below when communication is
lost.
B
Function Specifications
Speedometer
Tachometer C
Zero indication.
Fuel gauge
Engine coolant temperature gauge
D
Illumination control Meter illumination Change to nighttime mode when communication is lost.
Odometer Freeze current indication.
Segment LCD
CVT position Display turns off. E
Buzzer Buzzer turns off.
ABS warning lamp
Brake warning lamp F
VDC OFF indicator lamp Lamp turns on when communication is lost.
Malfunction indicator lamp
G
SLIP indicator lamp
A/T CHECK warning lamp
Oil pressure warning lamp H
Master warning lamp
Air bag warning lamp
I
Warning lamp/indicator lamp High beam indicator Lamp turns off when communication is lost.
Turn signal indicator lamp
CRUISE indicator lamp J
SET indicator lamp
Intelligent Key system warning lamp
K
Driver and passenger seat belt warn-
ing lamp
Lamp turns off when disconnected.
Charge warning lamp
L
Security indicator lamp
Lamp will flash every second for 1 minute and then stay on con-
Low tire pressure warning lamp
tinuously thereafter.
M
DTC Index INFOID:0000000005778883
WCS
Reference
CONSULT-III display Malfunction
page
Malfunction is detected in CAN communication. O
CAUTION:
CAN COMM CIRC
Even when there is no malfunction on CAN communication system, malfunction may be MWI-45
[U1000]
misinterpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 sec-
onds) or 10A fuse [No. 19, located in the fuse block (J/B)] is disconnected. P
Malfunction is detected when an erroneous speed signal is input.
VEHICLE SPEED
CAUTION:
CIRC MWI-46
Even when there is no malfunction on speed signal system, malfunction may be misin-
[B2205]
terpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 seconds).
NOTE:
“TIME” indicates the following.
• 0: Indicates that a malfunction is detected at present.
WCS
P
ALMIA0127ZZ
7 ON 0V
Ground Step lamp Output Step lamp
(R/W) OFF Battery voltage
LOCK (actuator is activat-
Battery voltage
8 ed)
Ground All doors LOCK Output All doors
(V) Other than LOCK (actuator
0V
is not activated)
UNLOCK (actuator is acti-
Battery voltage
9 Front door LH UN- vated)
Ground Output Front door LH
(G) LOCK Other than UNLOCK (actu-
0V
ator is not activated)
UNLOCK (actuator is acti-
Rear door RH and Battery voltage
101 Rear door RH vated)
Ground rear door LH UN- Output
(G/Y) and rear door LH Other than UNLOCK (actu-
LOCK 0V
ator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(Y/R)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position
Engine switch (push
146 Ground switch) illumination Input Tail lamp
(R/Y) ground ON
JSNIA0010GB
JSNIA0010GB E
15 OFF Battery voltage
Ground ACC indicator lamp Output Ignition switch
(Y/L) ACC or ON 0V
F
Turn signal switch OFF 0V
G
17 Ignition switch
Ground Turn signal (RH) Output
(G/B) ON Turn signal switch RH
H
PKID0926E
6.5 V
I
Turn signal switch OFF 0V
J
18 Ignition switch
Ground Turn signal (LH) Output
(G/Y) ON Turn signal switch LH
K
PKID0926E
6.5 V
L
19 Room lamp timer Interior room OFF Battery voltage
Ground Output
(Y) control lamp ON 0V
When outside of the vehi- M
Close to 5V
21 Ignition switch cle is bright
Ground Optical sensor signal Input
(P/B) ON When outside of the vehi-
Close to 0V
cle is dark WCS
OFF (clutch pedal is not
0V
22 Clutch interlock Clutch interlock depressed)
Ground Input
(R/Y) switch switch ON (clutch pedal is de- O
Battery voltage
pressed)
24
Ground Stop lamp switch 1 Input — Battery voltage
(R/W)
P
OFF (brake pedal is not de-
0V
26 pressed)
Ground Stop lamp switch 2 Input Stop lamp switch
(O/L) ON (brake pedal is de-
Battery voltage
pressed)
11.8V
UNLOCK status 0V
30 OFF 0
Ground ACC feedback signal Input Ignition switch
(V/Y) ACC or ON Battery voltage
11.8 V
ON (when front door RH
0V
opens)
JPMIA0012GB
1.1V
ON 0V
38 OFF 5V
Rear window defog- Rear window de-
(GR/ Ground Input
ger ON signal fogger switch ON 0V
W)
JPMIA0013GB
10.2V D
Ignition switch OFF or ACC 0V
Engine switch ON 5.5V
41
Ground
Engine switch (push
Output (push switch) illu-
E
(W) switch) illumination OFF 0V
mination
42 LOCK indicator ON 0V
Ground LOCK indicator lamp Output F
(R) lamp OFF Battery voltage
45 Receiver & sensor
Ground Input Ignition switch ON 0V
(P) ground
G
46 Receiver & sensor OFF 0V
Ground Output Ignition switch
(V/W) power supply output ACC or ON 5.0V
H
Standby state I
OCC3881D J
47 Tire pressure receiv- Input/ Ignition switch
Ground
(G/O) er signal Output ON
OCC3880D
M
48 Selector lever P/N P or N position 12.0V
Ground Input Selector lever
(R/G) position signal Except P and N positions 0V
ON 0V WCS
O
49 Security indicator sig-
Ground Output Security indicator Blinking
(L/O) nal
P
JPMIA0014GB
11.3V
OFF Battery voltage
10.7V
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
51 Combination switch Combination Any of the conditions below
Ground Output
(L/W) OUTPUT 1 switch with all switch OFF
• Wiper intermittent dial 1
• WIper intermittent dial 2
• Wiper intermittent dial 3
• Wiper intermittent dial 6 JPMIA0032GB
10.7V
All switch OFF 0V
Front wiper switch INT
Front wiper switch LO
Combination
53
Combination switch switch
(LG/ Ground Output
OUTPUT 3 (Wiper intermit-
R)
tent dial 4)
Lighting switch AUTO
JPMIA0034GB
10.7V
All switch OFF 0V
Front fog lamp switch ON
Lighting switch 2ND
Combination
54 Combination switch switch Lighting switch flash-to-
Ground Output
(G/Y) OUTPUT 4 (Wiper intermit- pass
tent dial 4)
10.7V
55 ON Battery voltage
Front blower mo-
(BR/ Ground Front blower monitor Input
tor switch OFF 0V
W)
D
OFF (front door LH
58 Front door LH CLOSE)
Ground Front door LH switch Input
(SB) switch
E
JPMIA0011GB
11.8V
ON (front door LH OPEN) 0V F
59 Rear window defog- Rear window de- Active Battery voltage
Ground Output
(G/R) ger relay fogger Not activated 0V
G
JMKIA0063GB
L
M
When Intelligent Key is in
the passenger compart-
ment WCS
JMKIA0062GB
JMKIA0063GB
624 Ground
Front outside handle
Output
door RH request
(B/Y) RH antenna (-) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0063GB
644 Ground
Front outside handle
Output
door LH request
(V) LH antenna (-) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
During waiting
K
JMKIA0064GB
M
When operating either button on Intelligent Key
WCS
JMKIA0065GB
JPMIA0041GB
1.4V
JPMIA0037GB
1.3V
1.3V
JPMIA0041GB
1.4V D
E
Lighting switch high-beam
(Wiper intermittent dial 4)
F
JPMIA0036GB
JPMIA0037GB
I
1.3V
J
Any of the conditions below
with all switch OFF
• Wiper intermittent dial 1
K
• Wiper intermittent dial 2
• Wiper intermittent dial 3
JPMIA0040GB
1.3V L
78 Input/
Ground CAN-L — —
(P) Output
79 Input/ M
Ground CAN-H — —
(L) Output
OFF 0V
W C S
JPMIA0015GB
P
6.5V
ON Battery voltage
81 OFF or ACC 0V
Ground ON indicator lamp Output Ignition switch
(LG) ON Battery voltage
83 OFF 0V
Ground ACC relay control Output Ignition switch
(L) ACC or ON Battery voltage
84
Ground CVT shift selector Output — Battery voltage
(Y/R)
884 Ground
Front door RH re-
Input
Front door RH re-
(P/L) quest switch quest switch OFF (not pressed)
JPMIA0016GB
1.0V
ON (pressed) 0V
894 Ground
Front door LH re-
Input
Front door LH re-
(B/W) quest switch quest switch OFF (not pressed)
JPMIA0016GB
1.0V
JPMIA0041GB
1.4V D
F
JPMIA0037GB
1.3V
G
Combination
95 Combination switch switch
H
Ground Input Turn signal switch RH
(R/W) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3V
JPMIA0038GB
1.3V L
WCS
JPMIA0039GB
1.3V
O
JPMIA0041GB
1.4V
JPMIA0038GB
JPMIA0036GB
1.3V
1.3V
JPMIA0041GB
1.4V D
E
Lighting switch flash-to-
pass
F
JPMIA0037GB
1.3V
G
Combination
97 Combination switch switch
H
Ground Input Lighting switch 2ND
(R/B) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3V
JPMIA0038GB
1.3V L
WCS
JPMIA0040GB
1.3V
Pressed 0V O
P
98
Ground Hazard switch Input Hazard switch
(G/O) Not pressed
JPMIA0012GB
1.1V
110 ON 0V
Ground Trunk room lamp Output Trunk room lamp
(V/W) OFF Battery voltage
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
I
When the trunk JMKIA0062GB
1194 Rear bumper anten- lid request switch
(BR/ Ground Output
na (+) is operated with
W) ignition switch J
OFF
When Intelligent Key is not
in the antenna detection
K
area
JMKIA0063GB
L
127 OFF or ACC Battery voltage
Ignition relay (IPDM
(BR/ Ground Output Ignition switch
E/R) control ON 0V
W) M
WCS
130 Trunk room lamp Trunk room lamp OFF (trunk is closed)
Ground Input
(Y/G) switch switch
O
JPMIA0011GB
11.8V
ON (trunk is open) 0V P
JPMIA0016GB
1.0V
11.8V
ON (when rear door RH
0V
opens)
11.8V
ON (when rear door LH
0V
opens)
1: Sedan
2: With LH front window anti-pinch
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
P
Priority DTC
1 • B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
NOTE:
Details of time display
WCS
ABNWA0658GB
ABNIA1933GB
WCS
ABNIA1934GB
ABNIA1935GB
WCS
ABNIA1936GB
ABNIA1937GB
SEDAN
WCS
ABNWA0657GB
P
ABNIA1928GB
WCS
ABNIA1929GB
ABNIA1930GB
WCS
ABNIA1931GB
ABNIA1932GB
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is C
released
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
D
Diagnosis Procedure INFOID:0000000005432785
Perform a unit inspection for the parking brake switch. Refer to MWI-55, "Component Inspection".
Is the inspection result normal? K
YES >> Replace the combination meter. Refer to MWI-153, "Removal and Installation".
NO >> Replace the parking brake switch.
L
WCS
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure INFOID:0000000005432787
WCS
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.