Instructions Manual
FOR
THE PARALLEL LATHES
_ OF B GROUP
BASIC TYPE: SNB 360CONTENTS.
Introduction
Description and operating range
Labte transport
Foundation and lathe installation
Lathe starting
Controls specification
Lathe kinematics
Gears list
Bearings list
Lubrication
Electric equipment
Lathe maintenance and adjusting
Feeds and threads adjusting on the lathe
Chuck mounting and dismounting instruc tions
‘Taper turning device
Footstock fast blocking mechanism use instructions
‘Accident prevention to lathe operating instructions
Normal accessories
‘Special accessories
Guarantees
Instructions Manual drawing listInstructions Manual
FOR THE PARALLEL LATHES
OF 8 GROUP
BASIC TYPE: SNB 360
INTREPRINDEREA DE STRUNGURI ARAD
Machine manufacturing number:
‘The continuons improvement of the machine — tools required by the technical
progress, to the apparition of certain contradictions between the delivered machine and
the Instructions Manual, and that is wh; are asking our beneficiaires that when ordering
spare parts to always indicate beside the lathe manufacturing number also the part number
marked on the spare part and indicated in the Instructions Manual.INTRODUCTION
‘The INSTRUCTIONS MANUAL is intentede to explain the parallel lathe of the SNB
+. type and by analogy the SNB 400 type installation, starting and servicing,
Before starting the lathe is very important to know its component parts, and a parti-
=is¢ care should be given to all its moving parts corresponding lubrication, Following exactly
+ instructions given in this manual you will succed in preventing damages and the pro
ing resultst will be of a high quality.
Before starting the machine, all the controlling elements should be carefully stu
=24, WE MENTION THAT THIS MACHINE CAN BE MADE WITH THE GEARBOX IN
40 VERSIONS (with mechanical clutches and electromagnetic clutches). CONTROL ELE-
ENTS AND THE BEST PART OF THE MAINTENANCE AND ADJUSTING PROCEDURES,
RE FUNCTION OF THE GEARBOX VERSION AND THEREFORE WE RECOMMEND
<5 DRAW NOT CONCLUSIONS FOLLOWING THE DRAWINGS IN THIS MANUAL INS-
[CTIONS BUT TO READ FIRST CAREF ULLY THE MANUAL TEXT.
The proccesing accuracy of each machine is checked to our works by a high precision
-strumentation
‘This checking being made with the autmost care the required precision is guaran-
in the acceptance conditions. To loose not this precision, the lathe should be transported
i mounted with care.
If you will observe all the things presented in this Manual you will be certainly
satisfied by the capacity and precision of the delivered lathe.
INTREPRINDEREA DE STRUNGURI ARADDESCRIPTION AND OPERATING RANGE
‘The parallel lathes of SNB 360 and SNB 400 type are of medium size with a maximum
cessing diameter over the slide ways of 360 mm and 400 mm respectively, and the main
movement drive installed power is of 7,5/6,1 kW. They can be used with a particular effici-
ency both in unique works and those of small and medium series, when proccesing in chuck
between centres. These lathes are manufactured in many versions namely:
— with stand with or without bridg.
— with the span between centres of 750, 1000, 1500 and 2000 mm
— wiht various ranges of the main shaft rotative speeds
‘These variants allow their adoption to various production requirements, The kine-
matics and construction of these lathes allows the following processings:
— longitudinal turning with manual or mechanic lead
— cross turning with manuel or mechanic lead
— boring with manual or mechanic lead and tool chucking in the tool holder
— metric threads, whitworth threads, module and Diametral Pitch threading
‘The parallel lathes of SNB 360 and SNB 400 type can be provided by a series of spe-
cial accessories as:
— taper turning device
— four dies faceplate
— threading indicator
— feed measuring device
— hydraulic duplicator
— hydraulic turning fixture
and their utilization considerably increases their performance, boardening at the same time
their utilization range.
TECHNICAL FEATURES OF SNB 360, AND SNB 400 LATHE THE| ELECTRIC AND
MECHANICAL VERSION
1. MAIN FEATURES SNB 360 SNB 400
— maximum processing diameter over
the stand, mm) 360 400
— main shaft height as against the stand
flat guide, mm 175 190
— span between centres, mm 730 750
1000 1000
1500 1500
2000 2000
— maximum processing diameter over
the slide, mm 185 210
— maximum rotating diameter in th:
bridge strain, mm 580 510
— maximum diameter of bar processing
through the main shaft, mm 30 50
— minimax. processing diameter with
travelling rest with small aperture, mm 14/0100
— min’max. processing diameter with
travelling rest with big aperture, mm 90/0180
— min/max. processing diameter with
ceatre rest with small aperture, mm @ 6/0100
— min/max. processing diameter with
centre rest with big aperture, mm 990/0180SNB 360 ‘SNB 400
2. HEADSTOCK,
— main shaft_end: short cone with STAS
7960 (DIN 55.022) bayonnet washers, size 6
— main shaft bore diameter, mm 52
— main shaft bore cone, mm Morse 6
— main shaft direct, speed steps number
— electric and mechanic version 18
— geometrical progression ration 1,25
— direct speed range rpm, 25-2000
3, FEED BOX AND THREADS
— longitudinal and cros feeds possible number 66
— longitudinal feeds range mmirot, 0,024—4.224
— cross feeds range mmrot. 0.008—1.40
— metric threads number 35
— metric threads range, mm 0.588
— Whitworth threads number 37
— Whitworth threads range 88-1
— module threads number 35
— module threads range 0.5—88
— Diametral Pitch threads number 37
— Diametral Pitch threads range ba—1
4, SLIDE AND CHUKS
— tool maximum section mm? 25x25 2x2
— tool slide rotating angle
— cross slide screw pitch, mm
— tool holder screw pitch,
—a division of the graduated ring
corresponds to @ cross slide shifting of, mm
— ditto of toolholder slide mm
— longitudinal slide maximum travel, — mm.
— transversal slide max. travel mm
— longitudinal slide travel to a hand-
wheel full rotation, mm
‘The repetition accuracy of uncoupling to the
plug of the longitudinal slide:
— idle running, mm
— under load, to the finishing operations, mm
— under load, roughing out operations, | mm
= tool slide maximum travel mm
5. CARRIAGE
— lead screw pitch, mm
— rack modulus, mm,
— longitudinal rapid feed amount, m/min
— cross rapid feed amount mimin
6. FOOTSTOCK
— spindle sleeve diameter, mm
— centre cone of spindle sleeve bore Morse
= footstock cross shift, mm
— footstock travel, mn
7. DRIVE
— Main motor: three-phase asynchronous
motor with base 380 V, 50 cps, IP 44
— motor power, kW
— Rapid feed motor: asynchronous rpm,
220/380 V. 50 cps, IP 44
225
0.025
0.05
975,
1475,
1975
225
233
7.5/6.1
3000/1500SNB 360 SNB 400
— motor power, kw 0.55
— motor speed rpm. 1000
3. COOLING PUMP
— water electric pump, 0,15 kW, 3000
pal 220/380 V, 90 eps, flow rate about
1m’ to 4,5 m water column
9. SIZE SNB 360 SNB 400
centres span 750 ~--1000»«-1500- 2000» 750«= 1000» 15002000
— length, (mm) 2250 2500-3000 «3500-2250 «25003000» 3500
— width (mm) 1120 1120
— height, (nm) 1400 1415
10. WEIGHT OF,
MACHINE (kg) 1550 1900 2000-2100 «2150-2200» 23002400
ateLATHE TRANSPORT 1
‘The free of package lathe transport should be carried out according to the diagram
presented in Fig, 2 of the Manual Instructions.
bar should be
introduced, and over its ends the cable eyes should be passed, and the cable further hocked to
‘Through special hole provided in the big leg of the lathe. a metalli
the crane hook. The same procedure should be applied for the lathe small leg
It should be carefully prevented the paint or various parts deterioration during
transport, and to this end, mild wood pieces should be ‘nserted under the cable in the contact
places.
When the lathe is packed (in case), its transportation should be carried out according
to the instructions printed on the case,
‘Unpacking should be done with great care, avoiding the lathe impairment by the
tools used to unpacking, To this end, it is recommended to take off firstly the case upper
cover followed by the other parts dismantling.
|
|
|
|
ey oP