Professional Documents
Culture Documents
Cat Electronic Technician 2019C v1.0 Cylinder Cutout Results - THY07138 - CYLCUT - 2020-08-07 - 16.07.06.xml 12.8.2020 09:09
Cat Electronic Technician 2019C v1.0 Cylinder Cutout Results - THY07138 - CYLCUT - 2020-08-07 - 16.07.06.xml 12.8.2020 09:09
Cat Electronic Technician 2019C v1.0 Cylinder Cutout Results - THY07138 - CYLCUT - 2020-08-07 - 16.07.06.xml 12.8.2020 09:09
12.8.2020 09:09
Test Summary
Parameter Value
Dealer Name: Teknox
Dealer Code:
Engine Serial Number: THY07138
Engine Model: C9 330D (THY07138)
Total Time: 1295 hours
Total Fuel: 37705 L
General
Parameter Value
Site Name:
Site Location:
Operator:
Dealer Name: Teknox
Dealer Code:
Date/Time Test Completed: 7.8.2020 16:06:23
Service Tool Serial Number: ET805973
Service Tool Version: 2019C v1.0
Cylinder Status
Cylinder Status
Cylinder 1 OK
Cylinder 2 OK
Cylinder 3 OK
Cylinder 4 OK
Cylinder 5 OK
Cylinder 6 Questionable
file:///C:/ProgramData/Caterpillar/Electronic%20Technician/temp/STPLReport1.HTM 12.8.2020
Page 2 of 4
Injector Code
**Warranty claim will be invalid if the injector code entered does not match the code
stamped on the physical injector.
Injector ECM Code Stamped Code
Injector 1 000000003B12297920E9 **********
Injector 2 000000003B12297975B3 **********
Injector 3 000000003B1229802839 **********
Injector 4 000000003B12297915CD **********
Injector 5 000000003B12297964A1 **********
Injector 6 000000003B12297929D6 **********
Fuel Delivery
Cylinder Fuel Delivery
Cylinder 1 21,910 mm3
Cylinder 2 23,251 mm3
Cylinder 3 23,756 mm3
Cylinder 4 22,731 mm3
Cylinder 5 21,691 mm3
Cylinder 6 21,184 mm3
All Firing Fuel Delivery: 16,505 mm3
Symptoms
Symptom Value
Low Power No
High Power No
Rough Idle (Engine Lope) No
Rough Running Under Load No
Hard Starting No
Stumble/Miss on Acceleration No
file:///C:/ProgramData/Caterpillar/Electronic%20Technician/temp/STPLReport1.HTM 12.8.2020
Page 3 of 4
Excessive Smoke No
Engine Information
Parameter Value
Engine Model: C9 330D (THY07138)
Engine Serial Number: THY07138
Equipment ID: 336D C9
Rated Peak Torque: 1356 N-m at 1400 rpm
Rated Power: 213 kW at 1800 rpm
Total Time: 1295 hours
Total Fuel: 37705 L
Total Distance: Unavailable
Personality Module Part Number: 4470861-00
Personality Module Release Date: JUL13
Personality Module Description: 330D-HEX-C9-HI_LSP
ECM Serial Number: 10897514JM
Test Conditions
The following conditions must be met for the automatic Cylinder Cutout Test:
1) Engine Speed must be between 825 rpm and 975 rpm (engine speed will be
automatically adjusted)
2) Engine Coolant Temperature must be 65 Deg C or higher
3) No default injector serial numbers (000000000000) allowed.
4) Injection Actuation Pressure must not vary by +/- 1500 kPa
5) Throttle position must not vary by +/- 5 %
6) No engine performance related active diagnostic codes are allowed
If at any time any of these conditions are not met, the test will automatically be aborted.
Note: Ensure transmission is in neutral or electrical load is removed from generator set.
Note: Fan cycling, A/C compressor cycling, or changes in engine load will invalidate this
test.
1) If the fan is not controlled by the engine ECM, please enable the fan if possible.
2) WARNING: If the ECM controls the fan, the fan will be turned ON automatically upon
starting this test.
file:///C:/ProgramData/Caterpillar/Electronic%20Technician/temp/STPLReport1.HTM 12.8.2020
Page 4 of 4
Comments
Run this test before and after repairing a cylinder to confirm a successful repair. Include
printed or electronic copies of the test results with any injectors that are returned to the
factory. Mark injectors with the cylinder number from which they were removed.
file:///C:/ProgramData/Caterpillar/Electronic%20Technician/temp/STPLReport1.HTM 12.8.2020