Professional Documents
Culture Documents
Deeplay-Eks-2018-001 - InLineStructureInstallationOnJLay
Deeplay-Eks-2018-001 - InLineStructureInstallationOnJLay
Deeplay-Eks-2018-001 - InLineStructureInstallationOnJLay
Ramp Angle vs. Vessel X-coordinate PLET X- coordinate vs. PLET Angle
ILS Structure Installation Analyses on J-Lay
Step by Steps Static Analyses Results
Von Mises Stress vs. Pipe Lift Off Tension vs. Bending Moment at ILS
• In General On these case, The Critical Static analyses during Installation happen when ILS near Surface,
before the dynamic Buoyancy module active.
ILS Structure Installation Analyses on J-Lay
Step by Steps Static Analyses Results
Step by Step ILS Installation Analyses Sheetname : 8Pr-ILS-D-1LS-Cur000 at file DeepLay-ILS-Installation-Rev01.xlsx
Step Ramp Pipe Length Vessel & T ens Catenary Profile ILS Coord & Angles T ension at Vm Stresses at ILS Anchor Flange Pipe Lift Off
Angle Upper Lower X Coord X Coord Length X Proj Gain X Coord Z Coord Angle T ens Bottom T ens ILS-U ILS-L Sagbend BM Shear T ension Monitor at RB
( ) (m) (m) (m) (m) (m) (m) (m) (m) (m) (m) ( deg ) ( Te ) ( Te ) (MPa) (MPa) (MPa) (MPa) (kN*m) (kN) (kN) (m) (m)
1 85.40 1500.0 10.0 -765.0 -842.6 1390.0 537.4 852.6 -843.6 6.9 86.1 46.9 3.5 144.7 64.9 210.1 158.3 76.2 11.4 45.7
2 85.40 1500.0 50.0 -725.0 -802.6 1390.0 537.4 852.6 -806.1 -33.0 85.7 44.7 3.6 162.2 104.6 229.1 171.7 84.8 12.6 41.5 -0.188 -0.320
3 85.40 1500.0 100.0 -675.0 -752.6 1395.0 542.4 852.6 -759.9 -82.9 85.0 44.7 3.6 143.0 110.4 236.0 176.7 88.0 13.0 40.7 -0.154 -0.260
4 83.20 1600.0 100.0 -625.0 -702.1 1450.0 648.0 802.0 -711.5 -82.6 82.7 45.8 4.8 245.2 215.7 251.2 186.7 93.8 14.5 41.7 -0.324 -0.557
5 83.20 1600.0 100.0 -625.0 -702.1 1445.0 643.0 802.0 -713.2 -82.4 81.0 36.7 4.7 166.6 241.8 141.1 167.9 85.4 15.6 32.6 -0.217 -0.371
6 81.00 1500.0 150.0 -575.0 -651.6 1450.0 648.5 801.5 -670.3 -131.8 80.0 36.8 4.8 280.8 228.5 127.7 185.3 80.2 14.5 31.8 -0.421 -0.735
7 81.00 1500.0 200.0 -525.0 -601.6 1440.0 638.5 801.5 -637.7 -179.7 76.2 26.5 4.6 89.7 168.4 137.7 125.6 60.3 8.6 21.3 -0.096 -0.148
8 81.00 1500.0 250.0 -475.0 -551.6 1440.0 638.5 801.5 -598.7 -228.5 75.5 26.5 4.6 77.8 159.3 145.5 119.9 56.8 7.9 20.5 -0.072 -0.105
9 81.00 1500.0 300.0 -425.0 -501.6 1440.0 638.5 801.5 -560.3 -277.2 74.8 26.5 4.6 71.1 153.3 150.5 116.8 54.5 7.9 19.7 -0.058 -0.080
10 81.00 1500.0 350.0 -375.0 -451.6 1440.0 638.5 801.5 -522.1 -325.8 74.1 26.5 4.5 68.2 149.9 152.9 116.9 54.4 7.9 18.8 -0.053 -0.070
11 81.00 1500.0 400.0 -325.0 -401.6 1440.0 638.5 801.5 -484.3 -374.3 73.4 26.5 4.5 68.2 148.7 153.2 117.5 54.7 7.8 18.0 -0.052 -0.070
12 81.00 1500.0 450.0 -275.0 -351.6 1440.0 638.5 801.5 -447.0 -422.6 72.6 26.5 4.5 68.6 147.8 153.3 118.1 55.0 7.7 17.2 -0.053 -0.071
13 81.00 1500.0 500.0 -225.0 -301.6 1440.0 638.5 801.5 -410.3 -470.8 71.7 26.5 4.5 69.1 146.8 153.4 118.8 55.2 7.6 16.4 -0.054 -0.073
14 81.00 1500.0 550.0 -175.0 -251.6 1440.0 638.5 801.5 -374.3 -518.8 70.8 26.5 4.5 69.8 145.9 153.3 119.4 55.3 7.4 15.6 -0.056 -0.076
15 81.00 1500.0 600.0 -125.0 -201.6 1440.0 638.5 801.5 -339.1 -566.5 69.8 26.5 4.5 70.8 145.1 153.1 119.9 55.4 7.3 14.7 -0.058 -0.079
16 81.00 1500.0 650.0 -75.0 -151.6 1440.0 638.5 801.5 -304.7 -614.0 68.6 26.5 4.5 71.8 144.2 152.8 120.4 55.3 7.1 13.9 -0.060 -0.083
17 81.00 1500.0 700.0 -25.0 -101.6 1440.0 638.5 801.5 -271.3 -661.1 67.3 26.5 4.5 73.0 143.2 152.4 120.8 55.2 7.0 13.1 -0.062 -0.087
18 81.00 1500.0 750.0 25.0 -51.6 1440.0 638.5 801.5 -238.9 -707.9 65.9 26.5 4.5 74.3 142.0 151.8 121.1 55.1 6.8 12.3 -0.065 -0.092
19 81.00 1500.0 800.0 75.0 -1.6 1440.0 638.5 801.5 -207.6 -754.1 64.3 26.5 4.5 75.7 140.5 151.0 121.2 54.8 6.6 11.5 -0.068 -0.097
20 81.00 1500.0 850.0 125.0 48.4 1440.0 638.5 801.5 -177.7 -799.8 62.4 26.5 4.5 77.2 138.8 150.0 121.1 54.3 6.4 10.8 -0.071 -0.103
21 81.00 1500.0 900.0 175.0 98.4 1440.0 638.5 801.5 -149.2 -844.8 60.3 26.5 4.4 78.9 136.6 148.5 120.6 53.7 6.3 10.0 -0.074 -0.109
22 81.00 1500.0 950.0 225.0 148.4 1440.0 638.5 801.5 -122.5 -888.9 57.8 26.5 4.4 80.7 133.8 146.5 119.7 52.7 6.0 9.2 -0.078 -0.116
23 81.00 1500.0 1000.0 275.0 198.4 1440.0 638.5 801.5 -97.7 -931.8 55.0 26.5 4.4 82.7 130.4 143.7 118.1 51.4 5.8 8.5 -0.082 -0.123
24 81.00 1500.0 1050.0 325.0 248.4 1440.0 638.5 801.5 -75.1 -973.2 51.7 26.5 4.4 84.7 126.0 139.9 118.1 49.6 5.6 7.8 -0.086 -0.130
25 81.00 1500.0 1100.0 375.0 298.4 1440.0 638.5 801.5 -55.0 -1012.8 47.8 26.5 4.4 86.7 120.8 134.7 118.2 47.0 5.3 7.1 -0.090 -0.138
26 81.00 1500.0 1150.0 425.0 348.4 1440.0 638.5 801.5 -37.9 -1049.8 43.2 26.5 4.4 88.5 116.5 127.8 118.3 43.6 5.1 6.5 -0.094 -0.144
27 81.00 1500.0 1200.0 475.0 398.4 1445.0 643.5 801.5 -23.9 -1083.6 37.8 26.5 4.4 89.7 111.1 121.3 118.4 39.0 4.7 5.9 -0.096 -0.148
28 81.00 1500.0 1250.0 525.0 448.4 1445.0 643.5 801.5 -13.4 -1113.2 31.6 26.6 4.4 89.9 104.9 113.8 118.4 33.1 4.4 5.4 -0.096 -0.149
29 81.00 1500.0 1300.0 575.0 498.4 1450.0 648.5 801.5 -6.3 -1137.7 24.6 26.7 4.4 88.5 98.3 105.6 118.2 25.9 4.0 5.0 -0.093 -0.143
30 81.00 1500.0 1350.0 625.0 548.4 1460.0 658.5 801.5 -2.2 -1156.2 17.0 26.8 4.4 84.9 92.6 98.1 116.9 17.8 3.5 4.7 -0.085 -0.129
31 81.00 1500.0 1400.0 675.0 598.4 1465.0 663.6 801.4 -0.5 -1168.5 9.1 27.0 4.5 78.8 89.5 92.7 113.0 9.6 3.0 4.6 -0.073 -0.107
32 81.00 1500.0 1450.0 725.0 648.4 1475.0 673.6 801.4 -0.1 -1174.2 1.6 27.1 4.6 71.2 95.5 93.7 115.9 13.3 3.3 4.6 -0.057 -0.078
33 81.00 1500.0 1500.0 775.0 698.4 1530.0 728.6 801.4 -0.1 -1174.4 0.2 27.2 4.6 68.9 130.5 119.2 116.0 42.6 5.1 4.6 -0.052 -0.070
ILS Structure Installation Analyses on J-Lay
Step by Steps Dynamic Analyses Results with Hs : 1.0m on Worst Heading & Period
Top Tension vs. Bottom Tension Von Mises Stress at Tensioner vs. Lift Off
ILS Structure Installation Analyses on J-Lay
Step by Steps Dynamic Analyses Results with Hs : 1.0m on Worst Heading & Period
Von Mises Stress at ILS-T vs. Max. Bending Moment at ILS Von Mises Stress at ILS-B vs. Max. Tension at ILS
• In General On these case, The Critical Dynamic analyses during Installation happen when ILS near Surface,
before the dynamic Buoyancy module active and near seabed when the ILS structure in contact with Seabed
during landing.
THANK YOU
http://www.linkedin.com/company/deeplay-energy-services/