Professional Documents
Culture Documents
Genesis WG4 Speaker Installation Sheet
Genesis WG4 Speaker Installation Sheet
Genesis WG4 Speaker Installation Sheet
Installation
Install this device in accordance with the latest edition of NFPA
72 and the local authority having jurisdiction.
WG4WA-S Outdoor-rated wall/ceiling speaker (25/70 V), multi- 4. Place the gasket over the backplate, and then feed the
tap, white with ALERT marking field wiring through the wire slots on the gasket and the
WG4WN-S Outdoor-rated wall/ceiling speaker (25/70 V), multi-
backplate. See Figure 2, item 2.
tap, white 5. Secure the backplate to the electrical box with four
WG4RN-S Outdoor-rated wall/ceiling speaker (25/70 V), multi- screws.
tap, red
6. Connect the wiring to the terminal strip.
WG4WF-S Outdoor-rated wall/ceiling speaker (25/70 V), multi-
tap, white with FIRE marking 7. Connect the speaker to the audio NAC. Observe polarity.
See Figure 2.
WG4RF-S Outdoor-rated wall/ceiling speaker (25/70 V), multi-
tap, red with FIRE marking 8. Set the speaker voltage.
The default speaker voltage is 70 V. For 25 V, reposition
Table 2: Accessories the speaker voltage selection switch S3. See Figure 2,
Number Description item 3.
WG4WTS [1] Outdoor-rated surface skirt, white - for Genesis WG4 9. Set the wattage.
speaker or speaker/strobe
The wattage default setting is Z corresponding to 1/4 watt.
WG4RTS [1] Outdoor-rated surface skirt, red - for Genesis WG4
To select a different wattage, align the S1 indicator to the
speaker or speaker/strobe
desired wattage setting. See Table 3 and Figure 2, item 1.
WGRGSKT Appliance replacement gasket
10. Position the cover over the backplate, and then secure it
[1] The trim skirt is outdoor-rated when used with the 449 weatherproof with the six cover screws.
box.
11. Test the unit for proper operation.
© 2011 UTC Fire & Security. All rights reserved. 1/4 P/N 3101852 • REV 2.0 • ISS 21MAR11
Figure 1: Exploded view of assembly Figure 3: Assembled
1
3
4
2
2
3 1
6
1. Optional skirt 3. Front cover
2. Backplate 4. Cover screws (6X)
SPKR - SPKR -
SPKR + SPKR +
3
DETAIL A
1. S1 wattage-setting switch (see Table 3.) 3. S3 speaker voltage-setting switch. UP position is 70 V (default);
2. Wire slot DOWN position is 25 V.
2W T 90 89.7
1W X 87.1 86.9
DO NOT PAINT
Z A
1/2 W Y 84.0 83.9
1/4 W Z 80.8 80.8
Z
A
dBA = Decibels, A-weighted.
UL 1480: Sound level output at 10 ft. (3.05 m) measured in a
reverberant room using 400 to 4,000 Hz band-limited pink noise.
Regulatory information
Manufacturer Edwards, A Division of UTC Fire & Security
A
Z
A Z
34202, USA
Year of manufacture The first two digits of the DATE MFG
number (located on the product identification
DO NOT PAINT
label) are the year of manufacture.
North American Meets: UL 1480
standards Follow: NFPA 72
Maintenance FCC compliance This device complies with part 15 of the
FCC Rules. Operation is subject to the
This unit is not serviceable or repairable. Should the unit fail to following two conditions: (1) This device may
operate, contact the supplier for replacement. not cause harmful interference, and (2) this
device must accept any interference
Perform a visual inspection and an operational test twice a received, including interference that may
year or as directed by the local authority having jurisdiction. cause undesired operation.
Industry Canada This Class A digital apparatus complies with
Caution: Do not change the factory-applied finish. compliance Canadian ICES-003