Professional Documents
Culture Documents
D H Reasi 8 Bedded
D H Reasi 8 Bedded
D H Reasi 8 Bedded
EARTH WORK
Earth work in excavation by mechanical means (Hydraulic
excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in
4 width as well as 10 sqm on plan) including getting out and disposal of Cum 53.1 350 18585
excavated earth lead upto 50 m and lift upto 1.5 m, as directed by
Engineer-in-charge.
CEMENT CONCRETE
Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shuttering - All work up to plinth 5800 101210
7 Cum 17.45
level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone
aggregate 40 mm nominal size)
MASONRY WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class
8 designation 7.5 in superstructure above plinth level up to floor V level in Cum 0.65 8000 5200
all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)
PLASTERING
12 mm cement plaster finished with a floating coat of neat cement of 400 6360
10 Sqm 15.9
mix :1:4 (1 cement: 4 fine sand)
RCC
FORM WORK
Centering and shuttering including strutting, propping etc. and removal of
16 form for all heights : Lintels, beams, plinth beams, girders, bressumers and Sqm 98.4 550 54120
cantilevers
STEEL WORK
Providing and fixing stainless steel ( Grade 304) railing made of Hollow
tubes, channels, plates etc., including welding, grinding, buffing, polishing
and making curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c fixing the railing with
18 necessary accessories & stainless steel dash fasteners , stainless steel bolts Kg 45 450 20250
etc., of required size, on the top of the floor or the side of waist slab with
suitable arrangement as per approval of Engineer-incharge, (for payment
purpose only weight of stainless steel members shall be considered
excluding fixing accessories such as nuts, bolts, fasteners etc.).
PANEL WORK
Supply and fixing of PUF panel Doors, windows, partitions, roof made up
of GI powder coated 0.47mm thick sheet on both sides, with 50 mm thick
class 'O' PUF of min.38kg/m3 density sandwiched in between. The GI
sheet shall have 80 micron thick powder coating by hot dip galvanizing
with zinc coating not less than 180gm/sqm on both sides of the panel.
24 Scope includes bottom runner, inter connecting profiles, fixing Sqm 318.96 1850 590076
arrangements, silicon sealant application and all other accessories required
to complete the work as per site requirement. Colour: Powder coated,
complete with all necessary hardware, accessories, fittings and fixtures, as
per description in individual items, technical specifications, drawings and
instructions of the Engineer-Incharge. including GI Frames.
ROOFING
Providing at all heights, levels and locations 0.45 mm thick Galvalume
sheet of Alloy 31500/31000/40800, conforming to IS 1254, IS 737, IS
2676. The sheet shall be fixed using self drilling/self tapping SS screws of
size 5.5x65 mm with EPDM seal complete upto required pitch in
25 horizontal, vertical or curved surfaces i/c cutting to size and shape where Sqm 202.11 500 101055
required as per the direction of Engineer-in-Charge. The rate shall be
inclusive of all screws, seal, ridge, labour, scaffolding, machinery for
fixing and approved sealant where required etc. but excluding the cost of
purlins, rafters and trusses.
ALUMINUM WORK
Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate Z
sections and other sections of approved make conforming to IS: 733 and
IS: 1285, fixing with dash fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top, bottom and sides with
required EPDM rubber/neoprene gasket etc. Aluminium sections shall be
27 smooth, rust free,straight, mitred and jointed mechanically wherever Kg 8 550 4400
required including cleat angle, Aluminium snap beading for glazing /
paneling, C.P. brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately) : For fixed portion
Powder coated aluminium (minimum thickness of powder coating 50
micron)
Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate Z
sections and other sections of approved make conforming to IS: 733 and
IS: 1285, fixing with dash fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top, bottom and sides with
required EPDM rubber/neoprene gasket etc. Aluminium sections shall be
smooth, rust free,straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap beading for glazing / 550 7150
28 Kg 13
paneling, C.P. brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately) : For shutters of
doors, windows & ventilators including providing and fixing hinges/
pivots and making provision for fixing of fittings wherever required
including the cost of EPDM rubber / neoprene gasket required (Fittings
shall be paid for separately) Powder coated aluminium (minimum
thickness of powder coating 50 micron)
Providing and fixing aluminium hanging floor door stopper ISI marked
anodised (anodic coating not less than grade AC 10 as per IS : 1868) 240 480
32 Each 2
transparent or dyed to required colour and shade with necessary screws
etc. complete. With twin rubber stopper
Providing and fixing aluminium die cast body tubular type universal
hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on 650 1300
33 Each 2
the body, door weight upto 35 kg and door width upto 700 mm), with
necessary accessories and screws etc. complete.
Providing and fixing bright finished brass tower bolts (barrel type) with 320 1280
34 Each 4
necessary screws etc. complete : 150x10 mm
Providing and fixing bright finished brass 100 mm mortice latch and lock
35 with 6 levers and a pair of lever handles of approved quality with Each 1 1500 1500
necessary screws etc. complete.
FLOORING
Providing and fixing Ist quality ceramic glazed wall tiles conforming to
IS: 15622 (thickness to be specified by the manufacturer), of approved
make, in all colours, shades except burgundy, bottle green, black of any
39 size as approved by Engineer-in-Charge, in skirting, risers of steps and Sqm 29.16 3100 90396
dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade complete.
Providing and laying vitrified floor tiles in different sizes (thickness to be
specified by the manufacturer) with water absorption less than 0.08% and
conforming to IS: 15622, of approved make, in all colours and shades, laid
on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with
grey cement slurry @ 3.3kg/sqm including grouting the joints with white 3100 77500
40 Sqm 25
cement and matching pigments etc., complete. Size of Tile 800x800 mm
sqm make Kajaria/ Restile/Johnson or equivqlent (Basic cost of tile -
Rs.85/sft).Any difference in basic price and OHP at the time of approval
shall be adjusted for the laid area.No extra shall be payable for forming
any pattern in the flooring like border, cut tiles,etc.
FALSE CEILING
Providing and fixing false ceiling at all height including providing and
fixing of frame work made of special sections, power pressed from M.S.
sheets and galvanized with zinc coating of 120 gms/sqm (both side
inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm
wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre
to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x
50mm long with 6mm dia bolts, other flange of cleat fixed to the angle
hangers of 25x10x0.50 mm of required length with nuts & bolts of
required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to
centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm
with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm
centre to centre, shall be fixed in a direction perpendicular to G.I.
intermediate channel with connecting clips made out of 2.64 mm dia x 230
mm long G.I. wire at every junction, including fixing perimeter channels 600 47274
43 Sqm 78.79
0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the
perimeter of ceiling fixed to wall/partition with the help of rawl plugs at
450 mm centre, with 25mm long dry wall screws @ 230 mm interval,
including fixing of gypsum board to ceiling section and perimeter channel
with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,
including jointing and finishing to a flush finish of tapered and square
edges of the board with recommended jointing compound , jointing tapes ,
finishing with jointing compound in 3 layers covering upto 150 mm on
both sides of joint and two coats of primer suitable for board, all as per
manufacturer's specification and also including the cost of making
openings for light fittings, grills, diffusers, cutouts made with frame of
perimeter channels suitably fixed, all complete as per drawings,
specification and direction of the Engineer in Charge but excluding the
cost of painting with :. 12.5 mm thick tapered edge gypsum moisture
resistant board
Providing and fixing tiled false ceiling of specified materials of size
595x595 mm in true horizontal level, suspended on inter locking metal
grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/
sqm, both side inclusive) consisting of main "T" runner with suitably
spaced joints to get required length and of size 24x38 mm made from 0.30
mm thick (minimum) sheet, spaced at 1200 mm center to center and cross
"T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm
long spaced between main "T" at 600 mm center to center to form a grid of
1200x600 mm and secondary cross "T" of length 600 mm and size 24x25
mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle
of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of
size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the
grid including, required cutting/making, opening for services like
diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" 600 35178
44 Sqm 58.63
runners to be suspended from ceiling using GI slotted cleats of size 27 x
37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash
fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of
size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T,
bottom exposed width of 24 mm of all T-sections shall be pre-painted with
polyester paint, all complete for all heights as per specifications, drawings
and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated
Tegular edge global white color tiles of size 595x595 mm and 0.5 mm
thick with 8 mm drop; made of GI sheet having galvanizing of 100
gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia
holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro
statically polyester powder coated of thickness 60 microns (minimum),
including factory painted after bending and perforation, and backed with a
black Glass fiber acoustical fleece.
CURTAIN WORK
PAINTING
Finishing with Epoxy paint (two or more coats) at all locations prepared
46 and applied as per manufacturer’s specifications including appropriate Sqm 300 3500 1050000
priming coat, preparation of surface, etc. complete. On steel work
Applying one coat of water thinnable cement primer of approved brand 500 7500
49 Sqm 15
and manufacture on wall surface : Water thinnable cement primer
Finishing with Deluxe Multi surface paint system for interiors using
Primer as per manufacturers specifications : Two or more coats applied on 300 4500
50 Sqm 15
walls @ 1.25 ltr/10 sqm over and including one coat of Special primer
applied @ 0.75 ltr /10 sqm
Painting Steel work with Deluxe Multi Surface Paint to give an even
51 shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of Sqm 33.5 350 11725
primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
SCRUB STATION
Providing and fixing of Two Tap Scrub Station as per the specification as
follows
1.Deep sloping basin
2. Two High mount spout/taps with elbow operated flow regulator (length
of flow regulator approximately 18-24cms)
3. Tap should have provision for manual aeration of water
4. 304 stainless steel polished and ground
5. Wall Mounted Design with provision for back panel wall bracket
fixation
52 6. Provision for Scrub Solution Stand with long handle for pumping Each 1 105000 105000
7. Sizes
a. Width – Approximately 130-140 cms
b. Height of Back Panel of sink – 90 -95 cms
c. Height of Sink from Ground – 100-110 cms
d. Depth of Sink from Top of the Sink – 40-45 cms
e. Height of Tap from the top of the sink – 25-28 cms
f. Gap Between two taps – 65- 68 cms
g. Protrusion of Sink from Wall – 45-50 cms
-
Providing and fixing PTMT Waste Coupling for wash basin and sink, of
54 approved quality and colour. Waste coupling 31 mm dia of 79 mm length Each 3 450 1350
and 62mm breadth weighing not less than 45 gms
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including 300 900
55 Each 3
P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia
-
Providing and fixing gun metal gate valve with C.I. wheel of approved 3000 6000
56 Each 2
quality (screwed end) : 25 mm nominal bore
-
Providing and fixing PTMT grating of approved quality and colour.
57 Rectangular type with openable circular lid 150 mm nominal size square Each 5 850 4250
100 mm diameter of the inner hinged round grating.
-
Providing and fixing C.P. brass long nose bib cock of approved quality
58 conforming to IS standards and weighing not less than 810 gms. 15 mm Each 10 1850 18500
nominal bore
-
Providing and fixing white vitreous china pedestal type water closet
(European type W.C. pan) with seat and lid, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with manually controlled
59 device (handle lever), conforming to IS : 7231, with all fittings and Each 4 9500 38000
fixtures complete, including cutting and making good the walls and floors
wherever required : W.C. pan with ISI marked white solid plastic seat and
lid
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1
60 metre long with S.S. triangular plate to Eureopean type W.C. of quality Each 4 1650 6600
and make as approved by Engineer - in - charge.
-
Providing and fixing PVC pipes, fittings including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings with
61 one step PVC solvent cement and testing of joints complete as per M 80 250 20000
direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work -
Exposed on wall
-
Providing and fixing PVC pipes, fittings including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings with
62 one step PVC solvent cement and testing of joints complete as per M 80 350 28000
direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work-
Exposed on wall
-
Providing and fixing PVC pipes, fittings including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings with
63 one step PVC solvent cement and testing of joints complete as per M 80 565 45200
direction of Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work -
Exposed on wall
-
Supplying and installing ready made PVC Septic tank including the cost of
carriage, trenching, placing at the level below ground level as specified as
64 per the direction of engineer in charge (Provision for Each 1 550000 550000
CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid
separately) 3. 25 to below 35 flush capacity
Providing and fixing C.P. brass angle valve for basin mixer and geyser 1050 12600
70 Each 12
points of approved quality conforming to IS:8931 :15mm nominal bore
FURNITURES
Providing & Fixing mid back chair .The seat & back are made up of
12mm thick hotpressed plywood, upholstered with fabric & moulded with
Polyurethane foam seat and back covers. The back foam should designed
with contouredlumbar support for extra comfort .The seat has extra thick
foam on front edge to give extra comfort.Mid back size 475 mm Width x
580 mm Height mm. And seat size 470 mm Width x 480 mm
Thepolyurethane foam should bemoulded with density = 45 kg/m3 and 7500 15000
71 Each 2
hardness = 16 +/2 kg on hampdem machine at 25% compression .Armrest
are injection moulded from black copolymer polypropylene. The
mechanism should befixed 360 degree revolving type,Upright position
locking, tilt tension adjustment, seat back tilting ratio 1:3. The pneumatic
height adjustment has an adjustment stroke of 12 cm. The pedestal should
be injection moulded in black 33 % glass filled in nylon 66 with 5 nos
twin wheel castors. The pedestal should be 66.3 cm pitch-center diameter.
Providing & Fixing table of size 5.58 ft X 2.5ft made up of 18mm particle
board with lamination on both sides. Side partitions, drawers, racks, lock
and laches etc including all complete both side laminated top. with 18 mm
thick door and 9 mm thick both side laminated drawer bottom and back
panel including necessary approved hinge, telescopic slide ,multipurpose
lock ,hanger rod of 25mm dia 16 gauge nickel plated MS Pipe ,2nos. tower 8500 8500
72 Each 1
bolt of barrel type having size 150 x 10mm, 4 nos. magnetic catcher triple
strip vertical type of approved quality, 128 mm handle , kd/minifix fitting,
edges to be sealed with PVC edge bending tape 2.00 mm thick of
approved brand fixture and finishing etc.. complete job. as per approved
shade and colour and as per Architecture drawing and Engineer in
Charge. .
SIGNAGES
Design, providing and fixing Digital Printed vinyl signage boards with
73 transparent 3mm acrylic Sheet with 4 nos. SS Studs of Size 48" x 18". Each 3 1050 3150
Complete as per the per the direction of Engineer in charge.
Design, providing and fixing Digital Printed vinyl signage boards with
74 transparent 3mm acrylic Sheet with 4 nos. SS Studs of Size 16" x 10". Each 20 300 6000
Complete as per the per the direction of Engineer in charge.
Total
5118652.5
ELECTRICAL WORKS.
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable in surface /
recessed medium class PVC conduit, with modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable etc. as required. switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable etc. as required.
Supplying and fixing of following sizes of medium class PVC conduit along
with accessories in surface/recess including cutting the wall and making good
the same in case of recessed conduit as required.(ISI Make)
a 20 mm 250 Metre 30
b 25 mm 200 Metre 35
Supplying and fixing two module stepped type electronic fan regulator on the
9 existing modular plate switch box including connections but excluding 4 Each 120
modular plate etc. as required.
Supplying and fixing of following ways surface/ recess mounting, vertical type,
415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder
painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth
11
bar, din bar for mounting MCBs (but without MCBs and incomer ) as
required . (Note : Vertical type MCB TPDB is normally used where 3 phase
outlets are required.)
4 way (4 + 12), Double door 1 Each 1800
Supplying and fixing following rating, four pole, 415 V, isolator in the existing
12 MCB DB complete with connections, testing and commissioning etc. as
required.
a 100 A 1 Each 1200
Supplying and fixing following way, single pole and neutral, sheet steel, MCB
distribution board, 240 V, on surface/ recess, complete with tinned copper bus
13
bar, neutral bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc. as required. (But without MCB/RCCB/Isolator)
Supplying and fixing following way, horizontal type three pole and neutral,
sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with
tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,
powder painted including earthing etc. as required. (But without
MCB/RCCB/Isolator)
a 6 way (4 + 18), Double door 1 Each 2200
15 S/F OF SP MCB
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve,
miniature circuit breaker suitable for inductive load of following poles in the
existing MCB DB complete with connections, testing and commissioning etc.
as required.
a 6/32 A SP MCB 36 Each 120
Providing and fixing following rating and breaking capacity and pole MCCB
with thermomagnetic release and terminal spreaders in existing cubicle panel
16
board including drilling holes in cubicle panel, making connections, etc. as
required.
100 A, 16 KA,TPMCCB 1 Each 6000
17 EARTHING
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories,
a and providing masonry enclosure with cover plate having locking arrangement 2 Set 11000
and watering pipe etc. with charcoal/ coke and salt as required.
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop
b earthing along with existing surface/ recessed conduit/ submain wiring/ cable 75 Metre 42
as required.
Providing and fixing earth bus of 50 mm X 5 mm copper strip on
c 0.45 Metre 2000
surface for connections etc. as required.
18 END TERMINATION
Supply and making end termination with brass compression gland, earth clip
and aluminium lugs for following size of PVC insulated and PVC
sheathed/XLPE aluminium conductor cable fo 1.1KV grade as required.
a 2x10 sqmm(19mm) 2 Each 880
b 3.5 x 25 sq.mm(28mm) 2 Each 1300
c 3.5 x 35 sq.mm(32mm) 2 Each 1560
d 4 X 10 sq. mm (25mm) 2 Each 900
19 Fire Detection &Alarm System
Supplying, installation, testing & commissioning sector panel suitable for
following zones, complete with visual indications for short circuit fault, open
a circuit fault, fire condition and all other standard facilities as per IS:2189 with 1 Each 10200
mimic diagram for all area/zone covered, complete with all connections,
interconnections as required. 2/4 ZONE
Supplying, installation, testing & commissioning of smoke detector with 1350
b 14 Each
builtin LED and mounting base complete with all connections etc. as required.
Supply of 20W LED tube fitting sleek with decorative end cap, powder coated
20.2 CRCA steel channel complete with all electrical accessories like electronic 3 Each 330
ballast, lamp holder, 20W LED lamp etc complete as required.
Supply and fixing of 18 W LED bulb and batten with its all accessories.[ISI
20.3 5 Each 230
MAKE]
Supply and installation of 1200 mm sweep ceiling fan, white colour, 5 star 2200
21 4 Each
rated as Per BEE complete with blades, down rod shackle, canopy etc.
Supplying and fixing following way, horizontal type three pole and neutral,
sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with
22 tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,
powder painted including earthing etc. as required. (But without
MCB/RCCB/Isolator)
12 way (4 + 36), Double door 1 Each 2700
23 CABLE SUPPLY & LAYING
Supplying, laying and clamping of one number PVC insulated and PVC
sheathed armoured aluminium power cable 1.1 KV grade of following sizes
using clamps noted along with the cables, spacing of clamps not exceeding 60
cm, making good the damages colour washing etc.
a 2 x 10 sqmm 25 Metre
b 4 x 10 sq.mm 25 Metre
c 3.5 x 25 sq.mm 25 Metre
d 3.5 x 35 sq.mm 75 Metre
FOR HVAC & LDB
Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed
armoured copper power cable, 1.1 KV grade of the following sizes using
23 clamps noted along with the cables, spacing of clamps not exceeding 60cms,
making good the damages , colour washing etc. as required (Make:Havells/
Glostar/Nicco/Finolex/Polycab)
23.1 4 X 4 sq.mm Copper Cable 65 Metre
b 4 X 16 sq.mm Copper Cable 65 Metre
24 S/F of TPN RCBO
Supplying and fixing following rating, four pole, (three phase and neutral) 415
volts RCBO, having a sensitivity current upto 100/300 milliamperes in the
existing MCB PDB complete with connections, testing and commissioning etc.
as required.
a 63 A 4P RCBO 100mA 1 Each 4200
25 S/F of TP MCB
Supplying and fixing 6 amps to 63 amps rating, 415 Volts, "C" series,
miniature cirucuit breaker suitable for lighting and other loads of following
poles in the existing MCB DB complete with connections, testing and
commissioning etc as required.(Make: Legrand/Havells/HPL)
a 63 A TP MCB 1 Each 1100
b 40 A TP MCB 1 Each 900
Supply and installation of Co2 Fire Extinguisher (Trolley Mount - Wheel
26 Operating) Type 4.5KG with MS clamps etc. for fixing on wall/wooden 1 No 2800
partition with 01 year warranty. I.S. No. 13849.
Supply and fixing RJ45 Keystone IO jack with cover and face plate, including
27 crimbing/Punching of UTP 4 Pair CAT 6E LAN Cables on both ends with 18 Each 8200
RJ45 Connector.
Supply and installation of wall mount 6 U CCTV DVR/NETWORK Cabinet 1800
28 1 Each
Box with lock including 3 power socket plug
Supply and installation of 10MP 10-Port Gigabit PoE Managed Switch with its
29 1 Each 6200
all accessories
30 Supply and fixing of Basic landline phone set complete with its all accessories. 1 Set 750
Supplying and fixing of metalic 415 V, 200A Copper Busbar distribution
31 1 Each
chamber with its all accessories.
o Work includes Earthing and supplying and fixing of suitable sized cables.
1 LS
50000
b Supply and fixing of 3+1 coaxial pure copper CCTV camera cable -172 Metre
1 LS
c Supply and fixing of BNC connector and DC jack for CCTV Cameras-8 Nos 50000
d Supply and fixing of 12V 36 Amps SMPS with its all accessories-1 Each
e Supply and fixing of 1 TB Hard disk Drive with its all accessories-1 Each
f Supply and fixing of 4 Channel DVR with its all accessories-1 Each.
Supply and installation of wall mount 6 U CCTV DVR/NETWORK Cabinet
g
Box with lock including 3 power socket plug -1 Each.
Supply and installation of 10MP 5-Port Gigabit PoE Managed Switch with its
h
all accessories-1 Each
35 HVAC-DUCTABLE SPLIT AIR CONDITIONER
PART A
SITC of DX type double skinned air handling units, ceiling suspended/ floor
mounting type with capacities listed below, complete with suitable DIDW
blower (as per approved make), blower section, static presure of 150 mm of
water column, built in pre filter, fine filter & hepa filter 99.97% effieciency
down to 0.3 microns and controls connected to condensing units, insulated SS
drain pan 6 row cooling coil, electric motor , direct driven package with TEFC
motor class B insulation, suitable for 3 phase, 415V 50Hz supply, suitable
1 AHU panel & cabling. AHU temp & speed control panel, ARI certified, with
0.70 mm sheet for outer skin and plain GP 0.63 mm sheet for inner skin 47mm
thick PUF panel, belt guards, suitable supports for suspending from slab,
vibration isolator, strip heater etc. conforming to specifications. Consider
ambient temerature range of (-7 degree to max 40 degree)Proper heating coils
should be added:
11 Providing & fixing charges of fine (EU 7) , pre (EU4) & hepa filters (EU13) 1 Nos 14800
PART C
12 DUCT/DUCT INSULATION / ACOUSTIC INSULATION
Supply, installation, balancing and commissioning of factory fabricated GSS
sheet metal rectangular/round ducting complete with neoprene rubber gaskets,
elbows, splitter dampers, vanes,
hangers, supports etc. as per approved drawings and specifications of following
sheet thickness complete as required.
12.1 Thickness 0.63 mm sheet 71 Sqm 1050
12.2 Thickness 0.80 mm sheet 10 Sqm 1150
Supplying and fixing of following thickness duly laminated aluminum foil of
mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct
13 after applying suitable adhesive for Nitrile rubber. The joints shall be sealed
with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation
complete as per specifications and as required.
13.1 19mm 86 Sqm 495
FIRE DAMPER
Supplying, Fixing,testing and commissioning of fire dampers in supply air
duct/main branch and return air path as and where required of required sizes i/c
control wiring,the damper shall be motorized and spring return so as to close
14 the damper in the event of power failure automatically and open the same in
case of power being restored. The spring return action shall be inbuilt
mechanism and not externally mounted. The damper shall also be closed in the
event of fire signal complete as required and as per specifications.
19500
4400
14000
11004
28000
350
3280
4720
1568
1760
960
1152
224
250
13500
7500
7000
480
10500
1800
1200
2700
500
1900
500
2200
4320
6000
22000
3150
900
1760
2600
3120
1800
10200
18900
650
1600
21120
16800
3500
990
1150
8800
8800
2700
0
0
0
0
0
0
0
4200
1100
900
2800
147600
1800
6200
750
50000
50000
385000
220000
4750
4750
0
8000
1200
175000
120000
2200
14800
74550
11500
42570
6400
6200
6400
12400
20400
1613278