Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

Guide to the Configuration of RTN Equipment

Networking Diagram

8
7 9

NE 1 NE 2
10 11
Node B RTN 905 2E RTN 905 2E RNC
NE 1 receives services from the NodeB and transmits the services 12 13
to the RNC through NE 2.

1 Configuring NE Attributes
2 Configuring Microwave Links
NE IDs must be unique network-wide. Configure the IP address of a gateway NE
based on the external DCN.
You can configure data for 1+0, 1+1, and XPIC microwave links by hop.
Set the NE name, NE ID, and NE IP address according to the engineering plan.
Tx high Tx low
Tx high Station Tx Freq. 19200M
NE Name NE 1 NE 2
Tx low Station Tx Freq. 18780M
NE ID 9-1 9-2 NE 1 NE 2 IF Channel Bandwidth 14MHz
RTN 905 2E RTN 905 2E
NE IP Address 129.9.0.1 129.9.0.2 Guaranteed Capacity Modulation QPSK
Note: Full Capacity Modulation 128QAM
See A1 and B for configuring a 1+0 microwave link.
See A2 and B for configuring 1+1 microwave links. TX Power(dBm) 16
See A3 and B for configuring XPIC microwave links. Power to Be Received(dBm) -16
1 A1. Configuring Basic Parameters for a 1+0 Microwave Link

1
2
2

4
3

6 3
A2. Configuring Basic Parameters for 1+1 Microwave Links B. Configuring IF and RF Parameters

3 3 4 4

A3. Configuring Basic Parameters for XPIC Microwave Links


5 5
1

3 3

6
3 Configuring a PLA Group Configuring VLAN-based E-Line Services

A PLA group can improve the Ethernet service bandwidth and reliability.

1
3

4
5

2
1

2 4

4 Configuring Ethernet Services


Configuring VLAN-based E-LAN Services
Ethernet services are classified into E-Line services and E-LAN services.

VLAN-based E-Line Service


VLANs can be used to separate E-Line services so that these services share one physical channel.
Service 1 NE 1 NE 2
Port 1 Port 1 Service 1
VLAN ID: 100 E-line Port 3 Port 3 E-line VLAN ID: 100 3
Transmission
Service 1 Port 2 e Network E Port 2 Service 1
E-lin - line
VLAN ID: 200 VLAN ID: 200
2
VLAN-based E-LAN Service
VLANs can be used to separate E-LAN services. In this case, a virtual bridge is divided into multiple
sub-switching domains. NE 2
SVLAN 300 User G2
NE 1 Port 1
CVLAN 100
SVLAN 300
Transmission Port 2 User H2
User G1 Port 1 Port 3 Network
Port 3
CVLAN 100
CVLAN 100 SVLAN 400 1 4 5
802.1ad bridge

Port 2 NE 3 6
User H1 Transmission SVLAN 300
Port 1 User G3
CVLAN 100 Network
Port 4 CVLAN 100
SVLAN 400 Port 3 Port 2
User H3
802.1ad bridge SVLAN 400 CVLAN 100 HUAWEI TECHNOLOGIES CO., LTD.
802.1ad bridge http://support.huawei.com
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.

You might also like