Professional Documents
Culture Documents
Vdocuments - MX Kruger Criticalspeeds Shafts
Vdocuments - MX Kruger Criticalspeeds Shafts
Vdocuments - MX Kruger Criticalspeeds Shafts
TBN017.0/1998
1-5
Technical Bulletin - TBN017.0/1998
1.2) 2.3)
wL3
δstI=
8EI
WA(3L2 − 4A 2 )
δst2=
24EI
(2) Maximum static deflection on load
only (δst2)
2.4)
2.1 )
WL3
δst2=
WL 3
3EI
δst2=
48EI
2.2 ) where :
w = weight of shaft, kg
W = weight of wheel, kg
E = modulus of elasticity, kg/m2
for shaft C40=200 x108 kg/m2
WB(L2 − B2 ) 3 / 2
δst2= I = moment of inertia=πD4/64, m4
9 3EIL L = length of shaft, m
Table I
2-5
Technical Bulletin - TBN017.0/1998
Example 1
Given the following specifications, find
the critical speed. (b) Total maximum static deflection
(δst)
= 0.00018 + 0.000139
= 0.000319 m
Diameter of shaft, D = 40 mm
30 g
Weight of wheel, W = 7.5 kg Nc =
Shaft length, L = 1.37 m π δst
Length, A = 0.205 m
Moment of inertia, I = 125.66 x 10-9 m4 30 9.81
=
Modulus of Elasticity, E= 200 x108 kg/m2 π 0.000319
(C40)
Shaft weight, w=1.37 x 9.87 =1675 rpm
=13.52 kg ---- refer to Table I
(a) Deflection from shaft weight only Safety factor 25%, therefore max.
operation speed = 1675 x 0.75
(δst I)
= 1256 rpm
5wL3
δstI= ---------------- refer to Fig. 1.1
384EI
5(13.52)(1.37 ) 3
=
384(200x10 8 )(125.66x10 −9 )
=0.00018 m
WA(3L2 − 4A 2 )
δst2= --refer to Fig. 2.3
24EI
7.5(0.205)[3(1.37 ) 2 − 4(0.205) 2 ]
=
24(200 x10 8 )(125 .66x10 −9 )
=0.000139 m
3-5
Technical Bulletin - TBN017.0/1998
Example 2
To check critical speed for KAT 12/12 S3 (b) Deflection from load only (δst2)
with 2-bearing, one side of the bearing
overhung. WA(3L2 − 4 A 2 )
δst2=
24EI
=0.000107 m
Diameter of shaft, D = 35 mm
Weight of wheel, W = 5.4 kg
Moment of inertia, I = 73.66 x 10-9 m4 (c) Total maximum static deflection
Modulus of Elasticity, E= 200 x108 kg/m2 (δst)
(C40)
δst =δstI+δst2
=0.000109 +0.000107
Check Critical Speed For Long Span
=0.000216m
30 g
Nc =
π δst
Length, A = 0.197 m
Length, L = 1.114 m
Shaft weight,w = 8.9 kg 30 9.81
=
π 0.000216
δstI=
384EI
Safety Factor 25%, therefore max.
operation speed = 2035 rpm x 0.75
5(8.9)(1.114 ) 3 = 1526 rpm
=
384(200 x10 8 )(73.66x10 −9 )
=0.000109 m
4-5
Technical Bulletin - TBN017.0/1998
Check Critical Speed For Overhung (d) Critical Speed at overhung (Nc)
30 g
Nc =
π δst
30 9.81
=
π 0.000228
Length, A = 0.5215
= 1980rpm
Length, L = 0.534 m
shaft weight,w = 4.27 kg
wL3 Conclusion
δstI=
8EI
Long Span
Critical Speed = 2035 rpm
4.27(0.534) 3 Max. operation speed = 1526 rpm
=
8(200x10 8 )(73.66x10 −9 )
Overhung
=0.000055 m Critical Speed = 1980 rpm
Max. operation speed = 1485 rpm
(b) Deflection from load only (δst2) Therefore, the max. operation speed for
this KAT 12/12 S3 should be according
WA 3 to the overhung, ie. whichever lesser,
δst2= which is = 1485 rpm
3EI
5.4(0.5215) 3
=
3(200 x10 8 )(73.66x10 −9 )
=0.000173 m
δst =δstI+δst2
=0.000055+0.000173
=0.000228m
5-5