Professional Documents
Culture Documents
Síntesis y Caracterización de Zeolitas Y A Partir de Fuentes Alternativas de Silicio y Aluminio
Síntesis y Caracterización de Zeolitas Y A Partir de Fuentes Alternativas de Silicio y Aluminio
Please cite this article as: L.B. Bortolatto, R.A.A. Boca Santa, J.C. Moreira, D.B. Machado, M.A.P.M.
Martins, Má.A. Fiori, N.C. Kuhnen, H.G. Riella, Synthesis and characterization of Y zeolites from
alternative silicon and aluminium sources, Microporous and Mesoporous Materials (2017), doi: 10.1016/
j.micromeso.2017.04.030.
This is a PDF file of an unedited manuscript that has been accepted for publication. As a service to
our customers we are providing this early version of the manuscript. The manuscript will undergo
copyediting, typesetting, and review of the resulting proof before it is published in its final form. Please
note that during the production process errors may be discovered which could affect the content, and all
legal disclaimers that apply to the journal pertain.
ACCEPTED MANUSCRIPT
Graphic abstract
PT
RI
U SC
AN
M
D
TE
C EP
AC
1
ACCEPTED MANUSCRIPT
1 Synthesis and characterization of Y zeolites from alternative silicon and aluminium
2 sources
3
a
4 Larissa B. Bortolatto, aRozineide A. A. Boca Santa, aJarina C. Moreira, aDiego B. Machado,
b
5 Maria Ana P. M. Martins, aMárcio A. Fiori, aNivaldo C. Kuhnen, aHumberto G. Riella
6
PT
a
7 Departamento de Engenharia Química e Engenharia de Alimentos, Universidade Federal de
8 Santa Catarina, 88040-900, Florianópolis – SC, Brasil
b
9 Departamento de Química, Universidade do Sul de Santa Catarina, 88704-090,
RI
10 Tubarão –SC, Brasil.
11
SC
12 Abstract. The synthesis of zeolites from alternative sources of silicon and aluminium are
13 promising routes to obtaining zeolitic materials. Such materials are typically applied in
U
14 catalytic and adsorptive processes, to obtain new products and at separation and purification
AN
15 processes. In order to obtain a material with environmentally friendly features, this research
16 was focused on the study of an effective and viable route for the synthesis of Y zeolite from
17 different sources of silicon and aluminium. In this research two types of metakaolin were used:
M
18 metakaolin residue (MKR) and metakaolin (MK). An experimental design was carried out as a
19 tool to evaluate the effects of time and temperature parameters and they influence on the
D
20 crystallization of zeolites with analytical reagents. The raw materials and the products obtained
TE
23 DTG), BET surface area analysis, Scanning Electron Microscopy (SEM), Scanning Electron
24 Microscopy with field emission (SEM / FEG) and Transmission Electron Microscopy (TEM).
25 The results obtained from the analysis and characterization showed that the route developed
C
26 through hydrothermal reaction for the synthesis of Y zeolite is significantly efficient. The
AC
27 synthesized zeolites were compared with a commercial zeolite and yielded promising results,
28 thus proving the efficiency of the proposed method. As a result of the experimental planning,
29 time was verified to be a key factor in the crystallinity of the zeolitic material.
30 Keywords. synthesis zeolite Y, waste purification, kaolin, metakaolin.
31
32 1. Introduction
33 The concern with the environment is fundamental nowadays, and thus the presence of
34 environment preservation methods has been increasing significantly. Numerous researches
2
ACCEPTED MANUSCRIPT
1 have been carried out aiming to develop new materials, such as zeolites, which are also known
2 as molecular sieves. Zeolites, due to their physical-chemical and morphological properties, are
3 promising materials which can be applied for the development of highly efficient technologies
4 and contribute for the preservation of the environment [1]. Since, the synthetic zeolites can be
5 produced with different sizes of pores according to the industrial needs of application.
6 In the zeolite's channels and cavities of interconnected molecular dimensions,
PT
7 compensation ions, water molecules or other adsorbates and salts can be found. The structure
8 of the zeolites imparts the same properties of great importance to the industrial processes [2,3].
RI
9 Currently more than 119 types of zeolitic structures are known, such as the type Y zeolites,
10 from the class of faujasites, which are of great industrial importance [4].
SC
11 Y zeolites (ZEO-Y) are formed by aluminosilicate crystals with the aspect of fine
12 powder and characterized by the presence of small micropores in their crystals [5]. The
13 material is employed in several processes, e.g. as selective adsorbents in separation processes
14
U
and in the purification of hydrocarbons, and, in their acid form, are the main component of
AN
15 catalysts utilized in petrol cracking.
16 The environmental friendly matters related to the production of zeolites also include the
M
17 integral or partial reuse of industrial waste, lowering the extraction of raw material and the
18 environmental liability deposited. Among the residues with an economic and technological
D
19 potential are the ones derived from the paper sludge, which, depending on the processing,
20 contain cellulose, calcium carbonate and a high concentration of kaolin in their structure [6].
TE
21 In this context, this research has been elaborated in order to evaluate the best processing
22 conditions for the attainment of ZEO-Y using different materials as the raw material for the
EP
23 synthesis. The zeolite Y was considered for the study because it presents numerous important
24 applications and an important role in the chemical industry, since it has a highly stable
crystalline structure, a large pore cavity and also large pore surface area [7]. Therefore, a (32)
C
25
26 experimental design was conducted and nine samples of ZEO-Y were synthetized from
AC
27 analytic reagents (ZEO-Y-AR) with the goal of testing the best temperature and reaction times.
28 From the best results obtained in th e synthesis of ZEO-Y-AR other two synthesis were carried
29 out employing two different kaolins as the source of aluminosilicates, in order to test
30 alternative raw materials for the attainment of ZEO-Y.
31 The kaolins utilized were a natural kaolin (NK) and one derived from paper sludge.
32 Kaolin is a mineral with good properties for zeolite production and has been used in a large
33 number of works [8]. Its microstructure has favorable SiO2 and Al2O3 concentrations for the
34 process, as can be seen in Table 4. Other minerals such as fly ash or mixtures of materials have
3
ACCEPTED MANUSCRIPT
1 been used [8]. However, the choice of the raw material used for the synthesis must consider the
2 future application of the produced zeolite. The kaolins were prepared and submitted to a heat
3 treatment, turning into natural metakaolin (ZEO-Y-NM) and purified metakaolin from
4 industrial white paper residues (ZEO-Y-WM).
5 The research has scientific merit since no other studies including the formulation and
6 synthesis of ZEO-Y from three alternative processes, including the evaluation of metakaolin
PT
7 derived from residues of the paper sludge , were found in the literature.
8
RI
9 2. Methodology
10 2.1. Materials
SC
11 The analytical reagents employed as a source of silicate and aluminium were sodium
12 silicate, Na2SiO3 (28,7% of SiO2, 8,09% of Na2O), produced by Manchester Chemistry, and
13 sodium aluminate, Na2Al2O4, from Sigma-Aldrich, respectively. Sodium hydroxide (NaOH) in
14
U
the form of micropearls, from Vetec, was utilized as a mineralizing agent and as a source of
AN
15 alkaline metal added to the process, and deionized water was used as a solvent.
16 A sample of commercial Y zeolite, provided by Petrobras' Research and Development
M
17 Ceter (CENPES), will be used as a comparison pattern (in a few essays) for the synthetized
18 zeolites.
D
19 The natural kaolin and the kaolin-rich industrial residues derived from paper sludge
20 were obtained from companies situated in the southern region of Brazil. Hydrochloric acid
TE
21 (HCl) was also utilized for the purification of residual kaolin. The methodology used to purify
22 the kaolin obtained from the paper residue was prepared according to the studies of Boca Santa
EP
23 et al. [9].
24
C
25
26 2.2. Experimental Design
AC
27 Based on the International Zeolite Association (IZA) [4] and in the works of Karami
28 and Rohani (2009) [7], a study of the best formulations for the attainment of ZEO-Y was
29 carried out. In order to obtain the best parameters and determine the main variations in
30 temperature and time for the synthesis of ZEO-Y, a three-level and two-variable experimental
31 design (32) totalizing 9 experiments was carried out (as shown in Table 1). The temperature
32 parameters tested for the reaction were from 80 to 120ºC and the reaction time intervals were
33 from 5 to 7 h (Table 1).
4
ACCEPTED MANUSCRIPT
1 The response surfaces and statistical models were computationally obtained with the
2 help of the software STATISTICA 6.0.
3 The responses to evaluate the crystallinity percentage of synthetized ZEO-Y were
4 attained by integrating the area of the crystalline peaks (software Origin) in the X-ray
5 diffractograms (XRD) and subtracting the area regarding the amorphous halo according to the
6 results of each sample. A similar study was carried out by Boca Santa (2016) [8].
PT
7
8
RI
9 2.3. Method for the synthesis of ZEO-Y- AR
10 The zeolites were obtained through the hydrothermal synthesis in steel cylindrical
SC
11 reactors internally coated with polytetraurethane, projected with a storage volume of 35 mL.
12 Initially, 4.07 g of NaOH were dissolved in 19.95 mL of water and kept under stirring.
13 Subsequently, 2.09 g of Na2Al2O4 (sodium aluminate) and 22.72 g of a Na2SiO3 solution
14
U
(28,7% of SiO2, 8,09% of Na2O) were added. The resulting solution was then stirred and left to
AN
15 stand for 24 h at 25 ºC. In a second stage 0.14 g of NaOH and 13.09 g of Na2Al2O4 were
16 dissolved in 130.97 g of deionized water, with a subsequent addition of 142.43 g of a Na2SiO3
M
17 solution (28,7% of SiO2, 8,09% of Na2O). At the end of this stage 16.50 g of the solution
18 prepared in the first stage were added, resulting in a gel which was left to stand for 24 h (a
D
19 mandatory ageing step for the formation of ZEO-Y-AR). After this period the gel was
20 transferred to the reactor and heated (hydrothermal treatment). After the predetermined time
TE
21 frames the solidified product was cooled and rinsed with water until reaching a pH close to 9.
22 The resulting material was then centrifuged and oven-dried at 60 ºC for 24 h.
EP
23 The methodology described was carried out for the synthesis of the nine samples of
24 ZEO-Y-AR, with respective time spans and temperatures according to the experimental design
C
25 described in Table 1.
26
AC
PT
7 Temperatures above 900 ° C can cause formation of crystalline structures in the material.
8 The methodology employed for the synthesis of ZEO-Y-NM and ZEO-Y-WM
RI
9 consisted in the following procedures: 10 g of metakaolin and 15 g of sodium hydroxide were
10 dispersed in 100 g of deionized water and kept under stirring for 30 min, with a
SC
11 metakaolin/NaOH ratio of 1/1.5 in mass units, according to a test performed by Htay et al.
12 (2008) [10]; to adjust the Si/Al ratio to 2.5 [11] approximately 14 g of sodium silicate
13 (Na2SiO3) were dispersed in 50 g of deionized water and the mixture was stirred for 30 minutes
14
U
for gel formation; the material was left to stand for 24 h and, subsequently, was transferred to
AN
15 the steel reactor and stored in an oven at 100 ºC for 6 h (best temperature and time obtained
16 with ZEO-Y-AR). After this period the material was first rinsed with water to lower its Ph,
M
27 Jeol (model JSM-6390LV). The specific area of the synthetized zeolites was determined by the
28 Brunauer, Emmet and Teller (BET) method in a Quantachrome Autosorb-1 device, employing
29 the multipoint method with data from nitrogen adsorption isotherms at 77K in vapor pressures
30 ranging between 0.01 and 0.99.
31
32 3. Results and discussion
33
34 3.1. Characterization of ZEO-Y-AR
6
ACCEPTED MANUSCRIPT
1 3.1.1. XRD of ZEO-Y-AR
2 The samples synthesized from the analytical reagents (ZEO-Y-AR) in temperatures
3 from 80 to 120 ºC in time intervals from 5 to 7 h were analysed by XRD technique. The results
4 are described in Figure 1.
5 Synthesized ZEO-Y-AR (Figure 1 (9), identified with the inscription (Y)) presents
6 peaks corresponding to the criteria of commercial Y zeolite, with intense diffraction peaks at
PT
7 2θ = 6.20o; 10.30o; 11.80o; 15.80o; 18.60o; 20.0o; 23.56o; 26.93o; 31.20o; 34.00o and 37.60o.
8 According to the pattern obtained by IZA (2014) [4] with the JCPDS 43-0168 form, such
RI
9 peaks are typical of sodium Y zeolite.
10 The results indicated that at certain temperatures and heating times some samples did
SC
11 not present the characteristics required for being considered a type Y zeolite, while others did
12 not react, or reacted in small proportions, resulting in the non-formation of the crystalline
13 peaks pertaining to the type Y zeolite.
14
U
AN
15 3.1.2. Evaluation of the factorial 3² design
16
M
17 The XRD results from all samples were subjected to integral calculations through the
18 software Origin to evaluate de crystallinity percentage. The percentage was attained by
D
19 subtracting the area of the peaks pertaining to ZEO-Y and dividing by the total area. According
20 to the zealotical standards it was possible to observe the samples with the greatest conversion
TE
25 94.25%. Table 3 shows the variance analysis, ANOVA, which aimed to verify significant
26 differences between the averages and the factors that may influence a dependant variable over
AC
27 crystallinity. It is possible to observe that the F values are significant (considering p < 0.5).
28 Furthermore, it can be inferred that the interaction between the variables temperature and time
29 (linear terms) has a large influence on the model composition, as is confirmed by the quadratic
30 sum (QS). Thus, the time factor (linear term) and temperature factor (linear term) are defined
31 as more interactive factors to the model. The model obtained demonstrated a good correlation
32 with its data, since the value of R2 is 0.93.
33 The Pareto Diagram, illustrated in Figure 2, shows the variables’ effect values.
7
ACCEPTED MANUSCRIPT
1 Zhang et al. (2014) [12] observed in their study that time is the most significant
2 variable for the crystallinity in the synthesis of the zeolite. Melo et al. (2012) [13] highlight
3 that time is an important parameter to be considered, since, generally, crystallinity increases
4 over time.
5 The response surface of the model applied to crystallinity is presented in Figure 3.
6 The point of greatest crystallinity for ZEO-Y is close to the central point from the
PT
7 planning (time of 6 hours and temperature of 100 ºC), confirming the Y zeolite’s synthesis
8 conditions presented by IZA.
RI
9 Thus, for the synthesis of ZEO-Y-IR and ZEO-Y-WM a temperature of 100 ºC and a
10 period of 6 hours were selected.
SC
11
12 3.2. Characterization of Waste (WM) and Natural Metakaolin (NM) and synthetized
13 ZEO-Y
14 3.2.1. FTIR spectres of WM and NM
U
AN
15 Figure 4 presents the infrared absorption spectres in the WM (a) and NM (b) samples.
16 The bands observed near 3459 cm-1 represent the OH group. These molecules are able to
M
17 vibrate in different ways and involve symmetrical and asymmetrical stretching or flexion
18 combinations. The band at 2350 cm-1 is attributed to carbon dioxide [14]. For the metakaolin
D
19 obtained from the waste the sample should, ideally, contain a few traces of cellulose, due to the
20 band at 1636 cm-1, which represents the OH group present in cellulose. The bands at 1083
TE
21 cm−1, 801 cm−1and 464 cm−1 represent the modifications of kaolin into metakaolin. The
22 absorptions occurring at 1083 and 1084 cm-1 correspond to the Si-O-Si interactions, while the
EP
23 bands at 800 and 801 cm−1 correspond to the Al-O interactions, and the ones at 465 and 464
24 cm−1 are related to a O-Si-O coupling, characteristic of kaolins [15]. The width of the three last
C
PT
7 ZEO-Y.
8 Table 4 reports the results of the chemical analysis conducted by XRD in natural
RI
9 metakaolin (NM), metakaolin derived from the waste of white paper pulping (WM) and
10 samples of ZEO-Y-IR, ZEO-Y-IM and ZEO-Y-WM.
SC
11 From the results of chemical analysis, presented on Table 4 (a and b), it is possible to
12 observe that, for both metakaolin samples, silicone oxide (SiO2) and aluminium oxide (Al2O3)
13 are the major components, corresponding to 90% of the material. Iron oxide (Fe2O3) and
14
U
calcium oxide (CaO) present greater concentration in the paper sludge metakaolin. The
AN
15 SiO2/Al2O3 ratio is observed to be close to 1.0 and, since for the synthesis of Y zeolite the most
16 favorable ratio is 2.0, an adjustment was necessary in silicon concentration.
M
19 oxides obtained from the sample synthesized for experiment nine (ZEO-Y-IR). The oxide
20 percentages observed in ZEO-Y-IR are close to the percentage values of the commercial
TE
21 zeolite. The stoichiometric Si/Al ratios are of 4.21 for ZEO-Y-S and 3.10 for ZEO-Y-IR. The
22 values are in accordance with the literature for ZEO-Y [1]. According to Breck (1984) [2], for
EP
23 ZEO-Y the Si/Al ratio is bigger than 1.5, whereas Meier and Olson (1992) [17] found this ratio
24 to vary from, approximately, 2.0 to 8.0.
C
25 The XRF results in Table 4 (e and f) were collected form the ZEO-Y-WM and ZEO-Y-
26 NM samples, respectively. In the WM sample a significant increase in titanium and iron
AC
27 concentrations stands out. According to Hildebrando (2012) [18], the presence of impurities in
28 the starting materials, such as those previously mentioned and, specially, iron-based
29 substances, are prone to causing disruptions during the synthesis reactions. The latter tend to
30 remain insoluble during the crystallization stage, leading to a precipitation of undesired
31 species, such as insoluble silicates, thus interfering in the zeolites’ formation process.
32 The Si/Al ratio was of 2.43 for ZEO-Y-WM and 2.26 for ZEO-Y-NM. These
33 composition ratios are characteristic of ZEO-Y [19].
9
ACCEPTED MANUSCRIPT
1 The zeolites produced are essentially composed of silicon and aluminium, with a
2 smaller amount of sodium, characteristic of NaY zeolites.
3
4 3.2.4. Diffractograms of ZEO-Y-WM and ZEO-Y-NM.
5 Through the crystalline peaks in the diffractograms presented in Figure 6 the formation
6 of ZEO-Y can be observed, as listed on the JCPDS 43-0168 sheet. In the diffractogram
PT
7 pertaining to ZEO-Y-WM (Figure 6a) it is also possible to observe the presence of crystalline
8 peaks corresponding to type P zeolite (ZEO-P). According to Huo et al. (2013) [20] the
RI
9 formation of ZEO-P can occur in more prolonged synthesis. Farzanet et al. (1989) [21] state
10 that the formation of ZEO-Y might vary depending on the composition of the gel formed in the
SC
11 beginning of the process and, mostly, due to a temperature variation in the synthesis and the
12 crystallization time. Freitas et al. (2011) [22] add that the P phase is more stable than the Y
13 phase, and can occur in synthesis stemming from metakaolin. According to Liu et al. (2003)
14
U
[23] the control of reaction temperature is an important factor for obtaining ZEO-Y with a high
AN
15 purity level, since crystallization at lower temperatures favors the synthesis of metastable
16 zeolitic materials, i.e. faujasites, while high temperatures tend to form more
M
17 thermodynamically stable phases. Thus, this study initially prioritized the knowledge of the
18 best temperature and time for the synthesis, in order to obtain ZEO-Y of commercial quality.
D
19 An increase in crystallization temperature can affect the properties of the reactional gel and
20 influence particle size and, in some cases, reduce the dimensions and accelerate the diffusion
TE
21 between particles.
22 Through the calculation of the areas of the XRD peaks a crystallinity of 75 and 78%
EP
23 was detected for ZEO-Y-WM (Fig. 6a) and ZEO-Y-NM (Fig. 6b), respectively. These values
24 were considered significant for the production of ZEO-Y from matakaolin, especially if
C
PT
7 In the FTIR spectres of the samples synthesized from metakaolins, presented in Figure
8 7 (b – c), vibrational bands can be observed in the wavelengths of 3470 and 1640 cm-1
RI
9 regarding the functional groups OH, which are attributed to water molecules [19].
10 Furthermore, vibrational frequencies around 1005, 1000, 565, 563, 467 and 461 cm-1 suggest
SC
11 that a formation of zeolitic materials occurred in the ZEO-Y-WM and ZEO-Y-NM samples,
12 involving structural changes that can be observed by a change in length when compared to the
13 matakaolin samples (Figure 4), especially in a shift of the regions close to 1083 cm-1 to 1005
14
U
cm-1. These changes can be related to the formation of zeolitic structures, with similar
AN
15 characteristics reported by Htay and Oo (2008) [10].
16 The occurrence of the referred vibrations can also be observed in the spectre of Figure
M
23 nuclei. The synthesized zeolites present smaller crystallite sizes and greater dispersion in
24 particle size when compared to ZEO-Y-S. This can also explain the increase in the surface area
C
27 probably due to an impurity in the waste material. . The micrographs of ZEO-Y presented an
28 octahedral morphology similar to those present in the study conducted by Breck (1984) [2] and
29 Kovo et al. (2009) [26]. Htay and Oo (2008) [10] also obtained ZEO-Y with the same
30 characteristics in their studies.
31
32 3.2.7. Results of the specific area essays by the BET method
33 In Table 5 are presented the values of specific area determined by the BET method in
34 the synthesized zeolites and in the standard sample.
11
ACCEPTED MANUSCRIPT
1 Zeolites show distinct superficial areas, indicating a variation in the density of
2 micropores. According to Yates (1968) [27], the increase in specific area contributes to the ion
3 exchange capacity, high adsorption and catalysis efficiency, due to the presence of spacious
4 cavities in the crystalline structure. ZEO-Y-AR (sample 9), synthesized from analytic reagents,
5 presented a surface area similar to ZEO-Y-S. The results of the specific areas obtained in the
6 essay are according to the results found in the literature for type Y zeolite (RAHMAN et al.,
PT
7 2012) [28].
8 ZEO-Y-NM was the sample which presented the largest surface area in relation to the
RI
9 ZEO-Y-WM sample, indicating the presence of bigger proportions of micropores. The
10 increased area indicates that there was a good crystallinity of this material, as well as a larger
SC
11 quantity of zeolitic structure formed through the synthesis. This value of BET area, around
12 554.9 m2. g-1, is superior to the 246.7 m2.g-1 obtained by Liu et al. (2003) [23], who synthesized
13 Y zeolite with 75% crystallinity from metakaolin. Furthermore, the zeolite from metakaolin
14
U
derived from industrial waste presented the smallest specific area, possibly due to the
AN
15 impurities contained in the material.
16 The results obtained by the BET essay are according to those of the morphology
M
19 4. Conclusion
20 From the synthesis of ZEO-Y employing analytical reagents as a silicon and aluminium
TE
21 source, it was possible to verify that the synthesis method based on IZA standart was
22 extremely adequate to the attainment of the faujisite phase (Y zeolite). The XRD analysis
EP
23 showed the formation of a ZEO-Y-AR from analytical reagents with an elevated crystallinity
24 degree, which is according to the standards found for Y zeolite. The experimental design
C
25 permitted the evaluation of the importance of the variables time and temperature in the process,
26 as well as the attainment of parameters to perform the substitution of the analytical reagents by
AC
27 alternative materials for the synthesis of ZEO-Y, including natural metakaolin and metakaolin
28 derived from paper sludge..
29 The SEM allowed the observation of the growth of crystals obtained in the synthesized
30 samples from analytical reagents and from two kaolins, and the crystals were quite similar to
31 those of the standard sample used as a reference.
32 The production of ZEO-Y in industrial scale from Brazilian kaolins can benefit several
33 different sectors. The reproduction through different materials led to the conclusion that ZEO-
12
ACCEPTED MANUSCRIPT
1 Y, in the synthesis conditions employed, can be produced according to the necessities from
2 other raw materials as a source of aluminosilicates.
3
4 Acknowledgments
5 The authors wish to thank CAPES, LCME and UFSC for the support to this research.
6
PT
7 5. References
8
RI
9 [1] G.G. Pace, A.R. Montes, G.F. Rodrigues. Zeolitas: características, propriedades y
10 aplicaciones industriales. Editorial Innovacín Tecnológica. Facultad de Ingeniería UCV.
11 Madri. 2000.
SC
12
13 [2] D.W. Breck. Zeolite molecular sieves. John Wiley & Sons. Inc. New York. 1984.
14
15 [3] A.B Luz, A.R. Campos, E.A. Carvalho, L.C. Bertolino. Caulim. Rio de Janeiro:
U
16 CETEM/ Rochas e Minerais Industriais: Usos e Especificações. (2005) 231-262.
17
AN
18 [4] IZA. Iza synthesis commission – fau linde type y. D. M. Ginter. A. T. Bell. C. J.
19 Radke. 2016.
20
M
21 [5] J.R. Scheiber. L.A. Lima. P.H.L. Quintela. E.L. Silva. M.G.F. Rodrigues. Síntese da
22 zeólita e sua utilização como adsorvente para remoção de contaminantes orgânicos em
23 efluentes líquidos. in: X Encontro Brasileiro sobre Adsorção. EBA. Guarujá – SP. 2014.
D
24
25 [6] R.A.A. Boca Santa, A.M. Bernardin, H.G. Riella, N.C. Kuhnen. Geopolymer Synthetized
26 from Bottom Coal Ash and Calcined Paper Sludge. J. Clean. Prod. 57 (2013) 302-307.
TE
27
28 [7] D. KARAMI, S. ROHANI. Synthesis of pure zeolite Y using soluble silicate, a two-
29 level factorial experimental design. Chem. Eng. Process. 48 (2009) 1288–1292. atualizada
EP
30
31 [8] R.A.A. Boca Santa, C. Soares, H.G. Riella. Geopolymers with a high percentage of
32 bottom ash for solidification/immobilization of different toxic metals. J. Hazard. Mater. 318
C
33 (2016) 145–153.atualizada
34
AC
PT
10 Engineering. Federal University of Santa Catarina. Florianópolis- SC. 2013.
11
12 [16] A.G. San Cristóbal, R. Castelló, M.A.M. Luengo, C. Vizcayno. Zeolites prepared
RI
13 from calcined and mechanically modified kaolins: A comparative study. Appl. Clay Sci. 49
14 (2010) 239-246.
15
SC
16 [17] W.M. Meier, D.H. Olson, Atlas of Zeolite Structure Types 3ed. rev. London,
17 Butterworth; Heinemann, 1992.
18
19 [18] E.A. HILDEBRANDO, Síntese de zeólita do tipo faujasita utilizando rejeito de
U
20 caulim da Amazônia como fonte de silício e alumínio: Aplicação como adsorvente. Thesis.
21 University of São Paulo. São Paulo - SP. 2013.
AN
22
23 [19] Q. Li, Y. Zhang, Z. Cao, W. Gao, L. Cui. Inuence of synthesis parameters on the
24 crystallinity and Si/Al ratio of NaY zeolite synthesized from kaolin. Pet. Sci. China University
M
28 NaP zeolite with different morphologies. J. Therm. Anal. Calorim. 111 (2013) 365-369.
29
30 [21] F. Farzanet, M.K. Oskooie, M.M.A. Nejad. The synthesis of zeolites A, X and HS
TE
31 from natural iranian kaolinite and the study of the transformation of zeolites X to HS and
32 zeolites Y to P, by x-ray diffraction and scanning electron microscopy. J. Sci. Islamic Replubic
33 Iran. 1 (1989) 23-28.
EP
34
35 [22] V.A.A. Freitas, J.S.V. Lima, P.R.C. Couceiro. Caracterização e análise estrutural
36 da Hidroxisodalita sintetizada a partir de amostras de solo amazônico. Cerâmica. 57 (2011)
C
37 281-287.
38
AC
39 [23] X. Liu, Z. Yan, H. Wang, Y. Luo. In situ synthesis of NaY zeolite with coal based
40 kaolin. J. Nat. Gas Chem. 12 (2003) 63-70.
41
42 [24] S. Kulprathipanja. Zeolites in Industrial Separation and Catalysis. Germany:
43 Wiley-VCH, 2010.
44
45 [25] N. Taufiqurrahmi, A. R. Mohamed, S. Bhatia. Nanocrystalline Zeolite Y.
46 Synthesis and Characterization. Mat. Sci Engineering, 17 (2011) 1-6.
47
48 [26] A.S. Kovo, O. Hernandez, S. M. Holmes. Synthesis and characterization of zeolite
49 Y and ZSM-5 from nigerian ahoko kaolin using a novel, lower temperature, metakaolinization
50 technique. J. Mater. Chem. 19 (2009) 6207-6212.
14
ACCEPTED MANUSCRIPT
1
2 [27] D.J.C. Yates, Studies on the surface area of zeolites, as determined by physical
3 adsorption and x-ray crystallography. Can. J. Chemistry. 46 (1968) 1695-1701.
4
5 [28] M.M. Rahman, M.B. Awang, A.N.M. Yusof. Preparation, characterization and
6 application of zeolite-Y (Na-Y) for water fitration. Aust. J. Basic Appl. Sci. 6 (2012) 50-55.
7
8 Table 1. Factorial planning 3².
PT
9 Table 2. Percentages obtained by integrating the area of the crystalline peaks for the 9
10 samples of synthesized ZEO-Y-AR.
RI
11 Table 3. Analysis of variance values (ANOVA), model with quadratic correlation (R2)
12 of 0.93.
SC
13 Table 4. Composition in oxides of WM (a), NM (b), a standard sample (ZEO-Y-S) (c)
14 and synthesized (d) ZEO-Y-AR (sample 9), (e) ZEO-Y-WM and (f) ZEO-Y-NM.
15 Table 5. Specific surface area of synthesized ZEO-Y and standard sample.
16
U
AN
17 Figure 1. Diffractograms of the nine samples synthesized with analytical reagents
18 Figure 2. Pareto Diagram of the effects for the crystallinity model.
M
21 Figure 5. XRD of (a) natural kaolin and (b) metakaolin from natural kaolin, and kaolin
22 from paper sludge (c) and metakaolin from paper sludge (d). .
TE
25 ZEO-Y-S.
26 Figure 8. Micrographies obtained in SEM of the following materials: natural kaolin (a);
C
27 NM (b); ZEO-Y-S (c); ZEO-Y-AR (sample 9) (d); ZEO-Y-WN (e) and ZEO-Y-NM (f).
28
AC
29
30
31
32
33
34
35
36
15
ACCEPTED MANUSCRIPT
1 Synthesis and characterization of Y zeolites from alternative silicon and aluminium
2 sources
3
a
4 Larissa B. Bortolatto, aRozineide A. A. Boca Santa, aJarina C. Moreira, aDiego B. Machado,
b
5 Maria Ana P. M. Martins, aMárcio A. Fiori, aNivaldo C. Kuhnen, aHumberto G. Riella
6
PT
a
7 Departamento de Engenharia Química e Engenharia de Alimentos, Universidade Federal de
8 Santa Catarina, 88040-900, Florianópolis – SC, Brasil
b
9 Departamento de Química, Universidade do Sul de Santa Catarina, 88704-090,
RI
10 Tubarão –SC, Brasil.
11
SC
12 Abstract. The synthesis of zeolites from alternative sources of silicon and aluminium are
13 promising routes to obtaining zeolitic materials. Such materials are typically applied in
U
14 catalytic and adsorptive processes, to obtain new products and at separation and purification
AN
15 processes. In order to obtain a material with environmentally friendly features, this research
16 was focused on the study of an effective and viable route for the synthesis of Y zeolite from
17 different sources of silicon and aluminium. In this research two types of metakaolin were used:
M
18 metakaolin residue (MKR) and metakaolin (MK). An experimental design was carried out as a
19 tool to evaluate the effects of time and temperature parameters and they influence on the
D
20 crystallization of zeolites with analytical reagents. The raw materials and the products obtained
TE
23 DTG), BET surface area analysis, Scanning Electron Microscopy (SEM), Scanning Electron
24 Microscopy with field emission (SEM / FEG) and Transmission Electron Microscopy (TEM).
25 The results obtained from the analysis and characterization showed that the route developed
C
26 through hydrothermal reaction for the synthesis of Y zeolite is significantly efficient. The
AC
27 synthesized zeolites were compared with a commercial zeolite and yielded promising results,
28 thus proving the efficiency of the proposed method. As a result of the experimental planning,
29 time was verified to be a key factor in the crystallinity of the zeolitic material.
30 Keywords. synthesis zeolite Y, waste purification, kaolin, metakaolin.
31
32 5. Introduction
33 The concern with the environment is fundamental nowadays, and thus the presence of
34 environment preservation methods has been increasing significantly. Numerous researches
16
ACCEPTED MANUSCRIPT
1 have been carried out aiming to develop new materials, such as zeolites, which are also known
2 as molecular sieves. Zeolites, due to their physical-chemical and morphological properties, are
3 promising materials which can be applied for the development of highly efficient technologies
4 and contribute for the preservation of the environment [1]. Since, the synthetic zeolites can be
5 produced with different sizes of pores according to the industrial needs of application.
6 In the zeolite's channels and cavities of interconnected molecular dimensions,
PT
7 compensation ions, water molecules or other adsorbates and salts can be found. The structure
8 of the zeolites imparts the same properties of great importance to the industrial processes [2,3].
RI
9 Currently more than 119 types of zeolitic structures are known, such as the type Y zeolites,
10 from the class of faujasites, which are of great industrial importance [4].
SC
11 Y zeolites (ZEO-Y) are formed by aluminosilicate crystals with the aspect of fine
12 powder and characterized by the presence of small micropores in their crystals [5]. The
13 material is employed in several processes, e.g. as selective adsorbents in separation processes
14
U
and in the purification of hydrocarbons, and, in their acid form, are the main component of
AN
15 catalysts utilized in petrol cracking.
16 The environmental friendly matters related to the production of zeolites also include the
M
17 integral or partial reuse of industrial waste, lowering the extraction of raw material and the
18 environmental liability deposited. Among the residues with an economic and technological
D
19 potential are the ones derived from the paper sludge, which, depending on the processing,
20 contain cellulose, calcium carbonate and a high concentration of kaolin in their structure [6].
TE
21 In this context, this research has been elaborated in order to evaluate the best processing
22 conditions for the attainment of ZEO-Y using different materials as the raw material for the
EP
23 synthesis. The zeolite Y was considered for the study because it presents numerous important
24 applications and an important role in the chemical industry, since it has a highly stable
crystalline structure, a large pore cavity and also large pore surface area [7]. Therefore, a (32)
C
25
26 experimental design was conducted and nine samples of ZEO-Y were synthetized from
AC
27 analytic reagents (ZEO-Y-AR) with the goal of testing the best temperature and reaction times.
28 From the best results obtained in th e synthesis of ZEO-Y-AR other two synthesis were carried
29 out employing two different kaolins as the source of aluminosilicates, in order to test
30 alternative raw materials for the attainment of ZEO-Y.
31 The kaolins utilized were a natural kaolin (NK) and one derived from paper sludge.
32 Kaolin is a mineral with good properties for zeolite production and has been used in a large
33 number of works [8]. Its microstructure has favorable SiO2 and Al2O3 concentrations for the
34 process, as can be seen in Table 4. Other minerals such as fly ash or mixtures of materials have
17
ACCEPTED MANUSCRIPT
1 been used [8]. However, the choice of the raw material used for the synthesis must consider the
2 future application of the produced zeolite. The kaolins were prepared and submitted to a heat
3 treatment, turning into natural metakaolin (ZEO-Y-NM) and purified metakaolin from
4 industrial white paper residues (ZEO-Y-WM).
5 The research has scientific merit since no other studies including the formulation and
6 synthesis of ZEO-Y from three alternative processes, including the evaluation of metakaolin
PT
7 derived from residues of the paper sludge , were found in the literature.
8
RI
9 6. Methodology
10 6.1. Materials
SC
11 The analytical reagents employed as a source of silicate and aluminium were sodium
12 silicate, Na2SiO3 (28,7% of SiO2, 8,09% of Na2O), produced by Manchester Chemistry, and
13 sodium aluminate, Na2Al2O4, from Sigma-Aldrich, respectively. Sodium hydroxide (NaOH) in
14
U
the form of micropearls, from Vetec, was utilized as a mineralizing agent and as a source of
AN
15 alkaline metal added to the process, and deionized water was used as a solvent.
16 A sample of commercial Y zeolite, provided by Petrobras' Research and Development
M
17 Ceter (CENPES), will be used as a comparison pattern (in a few essays) for the synthetized
18 zeolites.
D
19 The natural kaolin and the kaolin-rich industrial residues derived from paper sludge
20 were obtained from companies situated in the southern region of Brazil. Hydrochloric acid
TE
21 (HCl) was also utilized for the purification of residual kaolin. The methodology used to purify
22 the kaolin obtained from the paper residue was prepared according to the studies of Boca Santa
EP
23 et al. [9].
24
C
25
26 6.2. Experimental Design
AC
27 Based on the International Zeolite Association (IZA) [4] and in the works of Karami
28 and Rohani (2009) [7], a study of the best formulations for the attainment of ZEO-Y was
29 carried out. In order to obtain the best parameters and determine the main variations in
30 temperature and time for the synthesis of ZEO-Y, a three-level and two-variable experimental
31 design (32) totalizing 9 experiments was carried out (as shown in Table 1). The temperature
32 parameters tested for the reaction were from 80 to 120ºC and the reaction time intervals were
33 from 5 to 7 h (Table 1).
18
ACCEPTED MANUSCRIPT
1 The response surfaces and statistical models were computationally obtained with the
2 help of the software STATISTICA 6.0.
3 The responses to evaluate the crystallinity percentage of synthetized ZEO-Y were
4 attained by integrating the area of the crystalline peaks (software Origin) in the X-ray
5 diffractograms (XRD) and subtracting the area regarding the amorphous halo according to the
6 results of each sample. A similar study was carried out by Boca Santa (2016) [8].
PT
7
8
RI
9 6.3. Method for the synthesis of ZEO-Y- AR
10 The zeolites were obtained through the hydrothermal synthesis in steel cylindrical
SC
11 reactors internally coated with polytetraurethane, projected with a storage volume of 35 mL.
12 Initially, 4.07 g of NaOH were dissolved in 19.95 mL of water and kept under stirring.
13 Subsequently, 2.09 g of Na2Al2O4 (sodium aluminate) and 22.72 g of a Na2SiO3 solution
14
U
(28,7% of SiO2, 8,09% of Na2O) were added. The resulting solution was then stirred and left to
AN
15 stand for 24 h at 25 ºC. In a second stage 0.14 g of NaOH and 13.09 g of Na2Al2O4 were
16 dissolved in 130.97 g of deionized water, with a subsequent addition of 142.43 g of a Na2SiO3
M
17 solution (28,7% of SiO2, 8,09% of Na2O). At the end of this stage 16.50 g of the solution
18 prepared in the first stage were added, resulting in a gel which was left to stand for 24 h (a
D
19 mandatory ageing step for the formation of ZEO-Y-AR). After this period the gel was
20 transferred to the reactor and heated (hydrothermal treatment). After the predetermined time
TE
21 frames the solidified product was cooled and rinsed with water until reaching a pH close to 9.
22 The resulting material was then centrifuged and oven-dried at 60 ºC for 24 h.
EP
23 The methodology described was carried out for the synthesis of the nine samples of
24 ZEO-Y-AR, with respective time spans and temperatures according to the experimental design
C
25 described in Table 1.
26
AC
PT
7 Temperatures above 900 ° C can cause formation of crystalline structures in the material.
8 The methodology employed for the synthesis of ZEO-Y-NM and ZEO-Y-WM
RI
9 consisted in the following procedures: 10 g of metakaolin and 15 g of sodium hydroxide were
10 dispersed in 100 g of deionized water and kept under stirring for 30 min, with a
SC
11 metakaolin/NaOH ratio of 1/1.5 in mass units, according to a test performed by Htay et al.
12 (2008) [10]; to adjust the Si/Al ratio to 2.5 [11] approximately 14 g of sodium silicate
13 (Na2SiO3) were dispersed in 50 g of deionized water and the mixture was stirred for 30 minutes
14
U
for gel formation; the material was left to stand for 24 h and, subsequently, was transferred to
AN
15 the steel reactor and stored in an oven at 100 ºC for 6 h (best temperature and time obtained
16 with ZEO-Y-AR). After this period the material was first rinsed with water to lower its Ph,
M
27 Jeol (model JSM-6390LV). The specific area of the synthetized zeolites was determined by the
28 Brunauer, Emmet and Teller (BET) method in a Quantachrome Autosorb-1 device, employing
29 the multipoint method with data from nitrogen adsorption isotherms at 77K in vapor pressures
30 ranging between 0.01 and 0.99.
31
32 7. Results and discussion
33
34 7.1. Characterization of ZEO-Y-AR
20
ACCEPTED MANUSCRIPT
1 7.1.1. XRD of ZEO-Y-AR
2 The samples synthesized from the analytical reagents (ZEO-Y-AR) in temperatures
3 from 80 to 120 ºC in time intervals from 5 to 7 h were analysed by XRD technique. The results
4 are described in Figure 1.
5 Synthesized ZEO-Y-AR (Figure 1 (9), identified with the inscription (Y)) presents
6 peaks corresponding to the criteria of commercial Y zeolite, with intense diffraction peaks at
PT
7 2θ = 6.20o; 10.30o; 11.80o; 15.80o; 18.60o; 20.0o; 23.56o; 26.93o; 31.20o; 34.00o and 37.60o.
8 According to the pattern obtained by IZA (2014) [4] with the JCPDS 43-0168 form, such
RI
9 peaks are typical of sodium Y zeolite.
10 The results indicated that at certain temperatures and heating times some samples did
SC
11 not present the characteristics required for being considered a type Y zeolite, while others did
12 not react, or reacted in small proportions, resulting in the non-formation of the crystalline
13 peaks pertaining to the type Y zeolite.
14
U
AN
15 7.1.2. Evaluation of the factorial 3² design
16
M
17 The XRD results from all samples were subjected to integral calculations through the
18 software Origin to evaluate de crystallinity percentage. The percentage was attained by
D
19 subtracting the area of the peaks pertaining to ZEO-Y and dividing by the total area. According
20 to the zealotical standards it was possible to observe the samples with the greatest conversion
TE
25 94.25%. Table 3 shows the variance analysis, ANOVA, which aimed to verify significant
26 differences between the averages and the factors that may influence a dependant variable over
AC
27 crystallinity. It is possible to observe that the F values are significant (considering p < 0.5).
28 Furthermore, it can be inferred that the interaction between the variables temperature and time
29 (linear terms) has a large influence on the model composition, as is confirmed by the quadratic
30 sum (QS). Thus, the time factor (linear term) and temperature factor (linear term) are defined
31 as more interactive factors to the model. The model obtained demonstrated a good correlation
32 with its data, since the value of R2 is 0.93.
33 The Pareto Diagram, illustrated in Figure 2, shows the variables’ effect values.
21
ACCEPTED MANUSCRIPT
1 Zhang et al. (2014) [12] observed in their study that time is the most significant
2 variable for the crystallinity in the synthesis of the zeolite. Melo et al. (2012) [13] highlight
3 that time is an important parameter to be considered, since, generally, crystallinity increases
4 over time.
5 The response surface of the model applied to crystallinity is presented in Figure 3.
6 The point of greatest crystallinity for ZEO-Y is close to the central point from the
PT
7 planning (time of 6 hours and temperature of 100 ºC), confirming the Y zeolite’s synthesis
8 conditions presented by IZA.
RI
9 Thus, for the synthesis of ZEO-Y-IR and ZEO-Y-WM a temperature of 100 ºC and a
10 period of 6 hours were selected.
SC
11
12 7.2. Characterization of Waste (WM) and Natural Metakaolin (NM) and synthetized
13 ZEO-Y
14 7.2.1. FTIR spectres of WM and NM
U
AN
15 Figure 4 presents the infrared absorption spectres in the WM (a) and NM (b) samples.
16 The bands observed near 3459 cm-1 represent the OH group. These molecules are able to
M
17 vibrate in different ways and involve symmetrical and asymmetrical stretching or flexion
18 combinations. The band at 2350 cm-1 is attributed to carbon dioxide [14]. For the metakaolin
D
19 obtained from the waste the sample should, ideally, contain a few traces of cellulose, due to the
20 band at 1636 cm-1, which represents the OH group present in cellulose. The bands at 1083
TE
21 cm−1, 801 cm−1and 464 cm−1 represent the modifications of kaolin into metakaolin. The
22 absorptions occurring at 1083 and 1084 cm-1 correspond to the Si-O-Si interactions, while the
EP
23 bands at 800 and 801 cm−1 correspond to the Al-O interactions, and the ones at 465 and 464
24 cm−1 are related to a O-Si-O coupling, characteristic of kaolins [15]. The width of the three last
C
PT
7 ZEO-Y.
8 Table 4 reports the results of the chemical analysis conducted by XRD in natural
RI
9 metakaolin (NM), metakaolin derived from the waste of white paper pulping (WM) and
10 samples of ZEO-Y-IR, ZEO-Y-IM and ZEO-Y-WM.
SC
11 From the results of chemical analysis, presented on Table 4 (a and b), it is possible to
12 observe that, for both metakaolin samples, silicone oxide (SiO2) and aluminium oxide (Al2O3)
13 are the major components, corresponding to 90% of the material. Iron oxide (Fe2O3) and
14
U
calcium oxide (CaO) present greater concentration in the paper sludge metakaolin. The
AN
15 SiO2/Al2O3 ratio is observed to be close to 1.0 and, since for the synthesis of Y zeolite the most
16 favorable ratio is 2.0, an adjustment was necessary in silicon concentration.
M
19 oxides obtained from the sample synthesized for experiment nine (ZEO-Y-IR). The oxide
20 percentages observed in ZEO-Y-IR are close to the percentage values of the commercial
TE
21 zeolite. The stoichiometric Si/Al ratios are of 4.21 for ZEO-Y-S and 3.10 for ZEO-Y-IR. The
22 values are in accordance with the literature for ZEO-Y [1]. According to Breck (1984) [2], for
EP
23 ZEO-Y the Si/Al ratio is bigger than 1.5, whereas Meier and Olson (1992) [17] found this ratio
24 to vary from, approximately, 2.0 to 8.0.
C
25 The XRF results in Table 4 (e and f) were collected form the ZEO-Y-WM and ZEO-Y-
26 NM samples, respectively. In the WM sample a significant increase in titanium and iron
AC
27 concentrations stands out. According to Hildebrando (2012) [18], the presence of impurities in
28 the starting materials, such as those previously mentioned and, specially, iron-based
29 substances, are prone to causing disruptions during the synthesis reactions. The latter tend to
30 remain insoluble during the crystallization stage, leading to a precipitation of undesired
31 species, such as insoluble silicates, thus interfering in the zeolites’ formation process.
32 The Si/Al ratio was of 2.43 for ZEO-Y-WM and 2.26 for ZEO-Y-NM. These
33 composition ratios are characteristic of ZEO-Y [19].
23
ACCEPTED MANUSCRIPT
1 The zeolites produced are essentially composed of silicon and aluminium, with a
2 smaller amount of sodium, characteristic of NaY zeolites.
3
4 7.2.4. Diffractograms of ZEO-Y-WM and ZEO-Y-NM.
5 Through the crystalline peaks in the diffractograms presented in Figure 6 the formation
6 of ZEO-Y can be observed, as listed on the JCPDS 43-0168 sheet. In the diffractogram
PT
7 pertaining to ZEO-Y-WM (Figure 6a) it is also possible to observe the presence of crystalline
8 peaks corresponding to type P zeolite (ZEO-P). According to Huo et al. (2013) [20] the
RI
9 formation of ZEO-P can occur in more prolonged synthesis. Farzanet et al. (1989) [21] state
10 that the formation of ZEO-Y might vary depending on the composition of the gel formed in the
SC
11 beginning of the process and, mostly, due to a temperature variation in the synthesis and the
12 crystallization time. Freitas et al. (2011) [22] add that the P phase is more stable than the Y
13 phase, and can occur in synthesis stemming from metakaolin. According to Liu et al. (2003)
14
U
[23] the control of reaction temperature is an important factor for obtaining ZEO-Y with a high
AN
15 purity level, since crystallization at lower temperatures favors the synthesis of metastable
16 zeolitic materials, i.e. faujasites, while high temperatures tend to form more
M
17 thermodynamically stable phases. Thus, this study initially prioritized the knowledge of the
18 best temperature and time for the synthesis, in order to obtain ZEO-Y of commercial quality.
D
19 An increase in crystallization temperature can affect the properties of the reactional gel and
20 influence particle size and, in some cases, reduce the dimensions and accelerate the diffusion
TE
21 between particles.
22 Through the calculation of the areas of the XRD peaks a crystallinity of 75 and 78%
EP
23 was detected for ZEO-Y-WM (Fig. 6a) and ZEO-Y-NM (Fig. 6b), respectively. These values
24 were considered significant for the production of ZEO-Y from matakaolin, especially if
C
PT
7 In the FTIR spectres of the samples synthesized from metakaolins, presented in Figure
8 7 (b – c), vibrational bands can be observed in the wavelengths of 3470 and 1640 cm-1
RI
9 regarding the functional groups OH, which are attributed to water molecules [19].
10 Furthermore, vibrational frequencies around 1005, 1000, 565, 563, 467 and 461 cm-1 suggest
SC
11 that a formation of zeolitic materials occurred in the ZEO-Y-WM and ZEO-Y-NM samples,
12 involving structural changes that can be observed by a change in length when compared to the
13 matakaolin samples (Figure 4), especially in a shift of the regions close to 1083 cm-1 to 1005
14
U
cm-1. These changes can be related to the formation of zeolitic structures, with similar
AN
15 characteristics reported by Htay and Oo (2008) [10].
16 The occurrence of the referred vibrations can also be observed in the spectre of Figure
M
23 nuclei. The synthesized zeolites present smaller crystallite sizes and greater dispersion in
24 particle size when compared to ZEO-Y-S. This can also explain the increase in the surface area
C
27 probably due to an impurity in the waste material. . The micrographs of ZEO-Y presented an
28 octahedral morphology similar to those present in the study conducted by Breck (1984) [2] and
29 Kovo et al. (2009) [26]. Htay and Oo (2008) [10] also obtained ZEO-Y with the same
30 characteristics in their studies.
31
32 7.2.7. Results of the specific area essays by the BET method
33 In Table 5 are presented the values of specific area determined by the BET method in
34 the synthesized zeolites and in the standard sample.
25
ACCEPTED MANUSCRIPT
1 Zeolites show distinct superficial areas, indicating a variation in the density of
2 micropores. According to Yates (1968) [27], the increase in specific area contributes to the ion
3 exchange capacity, high adsorption and catalysis efficiency, due to the presence of spacious
4 cavities in the crystalline structure. ZEO-Y-AR (sample 9), synthesized from analytic reagents,
5 presented a surface area similar to ZEO-Y-S. The results of the specific areas obtained in the
6 essay are according to the results found in the literature for type Y zeolite (RAHMAN et al.,
PT
7 2012) [28].
8 ZEO-Y-NM was the sample which presented the largest surface area in relation to the
RI
9 ZEO-Y-WM sample, indicating the presence of bigger proportions of micropores. The
10 increased area indicates that there was a good crystallinity of this material, as well as a larger
SC
11 quantity of zeolitic structure formed through the synthesis. This value of BET area, around
12 554.9 m2. g-1, is superior to the 246.7 m2.g-1 obtained by Liu et al. (2003) [23], who synthesized
13 Y zeolite with 75% crystallinity from metakaolin. Furthermore, the zeolite from metakaolin
14
U
derived from industrial waste presented the smallest specific area, possibly due to the
AN
15 impurities contained in the material.
16 The results obtained by the BET essay are according to those of the morphology
M
19 8. Conclusion
20 From the synthesis of ZEO-Y employing analytical reagents as a silicon and aluminium
TE
21 source, it was possible to verify that the synthesis method based on IZA standart was
22 extremely adequate to the attainment of the faujisite phase (Y zeolite). The XRD analysis
EP
23 showed the formation of a ZEO-Y-AR from analytical reagents with an elevated crystallinity
24 degree, which is according to the standards found for Y zeolite. The experimental design
C
25 permitted the evaluation of the importance of the variables time and temperature in the process,
26 as well as the attainment of parameters to perform the substitution of the analytical reagents by
AC
27 alternative materials for the synthesis of ZEO-Y, including natural metakaolin and metakaolin
28 derived from paper sludge.
29 The SEM allowed the observation of the growth of crystals obtained in the synthesized
30 samples from analytical reagents and from two kaolins, and the crystals were quite similar to
31 those of the standard sample used as a reference.
32 The production of ZEO-Y in industrial scale from Brazilian kaolins can benefit several
33 different sectors. The reproduction through different materials led to the conclusion that ZEO-
26
ACCEPTED MANUSCRIPT
1 Y, in the synthesis conditions employed, can be produced according to the necessities from
2 other raw materials as a source of aluminosilicates.
3
4 Acknowledgments
5 The authors wish to thank CAPES, LCME and UFSC for the support to this research.
6
PT
7 6. References
8
RI
9 [1] G.G. Pace, A.R. Montes, G.F. Rodrigues. Zeolitas: características, propriedades y
10 aplicaciones industriales. Editorial Innovacín Tecnológica. Facultad de Ingeniería UCV.
11 Madri. 2000.
SC
12
13 [2] D.W. Breck. Zeolite molecular sieves. John Wiley & Sons. Inc. New York. 1984.
14
15 [3] A.B Luz, A.R. Campos, E.A. Carvalho, L.C. Bertolino. Caulim. Rio de Janeiro:
U
16 CETEM/ Rochas e Minerais Industriais: Usos e Especificações. (2005) 231-262.
17
AN
18 [4] IZA. Iza synthesis commission – fau linde type y. D. M. Ginter. A. T. Bell. C. J.
19 Radke. 2016.
20
M
21 [5] J.R. Scheiber. L.A. Lima. P.H.L. Quintela. E.L. Silva. M.G.F. Rodrigues. Síntese da
22 zeólita e sua utilização como adsorvente para remoção de contaminantes orgânicos em
23 efluentes líquidos. in: X Encontro Brasileiro sobre Adsorção. EBA. Guarujá – SP. 2014.
D
24
25 [6] R.A.A. Boca Santa, A.M. Bernardin, H.G. Riella, N.C. Kuhnen. Geopolymer
26 Synthetized from Bottom Coal Ash and Calcined Paper Sludge. J. Clean. Prod. 57 (2013)
TE
27 302-307.
28 [7] D. KARAMI, S. ROHANI. Synthesis of pure zeolite Y using soluble silicate, a two-
29 level factorial experimental design. Chem. Eng. Process. 48 (2009) 1288–1292.
EP
30
31 [8] R.A.A. Boca Santa, C. Soares, H.G. Riella. Geopolymers with a high percentage of
32 bottom ash for solidification/immobilization of different toxic metals. J. Hazard. Mater. 318
C
33 (2016) 145–153.
34
AC
PT
10 resíduo da indústria de papel. Master Thesis. Department of Chemical Engineering and Food
11 Engineering. Federal University of Santa Catarina. Florianópolis- SC. 2013.
12
RI
13 [16] A.G. San Cristóbal, R. Castelló, M.A.M. Luengo, C. Vizcayno. Zeolites prepared
14 from calcined and mechanically modified kaolins: A comparative study. Appl. Clay Sci. 49
15 (2010) 239-246.
SC
16
17 [17] W.M. Meier, D.H. Olson, Atlas of Zeolite Structure Types 3ed. rev. London,
18 Butterworth; Heinemann, 1992.
19
U
20 [18] E.A. HILDEBRANDO, Síntese de zeólita do tipo faujasita utilizando rejeito de
21 caulim da Amazônia como fonte de silício e alumínio: Aplicação como adsorvente. Thesis.
AN
22 University of São Paulo. São Paulo - SP. 2013.
23
24 [19] Q. Li, Y. Zhang, Z. Cao, W. Gao, L. Cui. Inuence of synthesis parameters on the
M
25 crystallinity and Si/Al ratio of NaY zeolite synthesized from kaolin. Pet. Sci. China University
26 of Petroleum (Beijing). 7 (2010) 403-409.
27
D
28 [20] Z. Huo, X. Xu, Z. Lv, J. Song, M. He, Z. Li, Q. Wang, L. Yan, Y. Li. Thermal
29 study of NaP zeolite with different morphologies. J. Therm. Anal. Calorim. 111 (2013) 365-
30 369.
TE
31
32 [21] F. Farzanet, M.K. Oskooie, M.M.A. Nejad. The synthesis of zeolites A, X and HS
33 from natural iranian kaolinite and the study of the transformation of zeolites X to HS and
EP
34 zeolites Y to P, by x-ray diffraction and scanning electron microscopy. J. Sci. Islamic Replubic
35 Iran. 1 (1989) 23-28.
36
C
37 [22] V.A.A. Freitas, J.S.V. Lima, P.R.C. Couceiro. Caracterização e análise estrutural
38 da Hidroxisodalita sintetizada a partir de amostras de solo amazônico. Cerâmica. 57 (2011)
AC
39 281-287.
40
41 [23] X. Liu, Z. Yan, H. Wang, Y. Luo. In situ synthesis of NaY zeolite with coal based
42 kaolin. J. Nat. Gas Chem. 12 (2003) 63-70.
43
44 [24] S. Kulprathipanja. Zeolites in Industrial Separation and Catalysis. Germany:
45 Wiley-VCH, 2010.
46
47 [25] N. Taufiqurrahmi, A. R. Mohamed, S. Bhatia. Nanocrystalline Zeolite Y.
48 Synthesis and Characterization. Mat. Sci Engineering, 17 (2011) 1-6.
49
28
ACCEPTED MANUSCRIPT
1 [26] A.S. Kovo, O. Hernandez, S. M. Holmes. Synthesis and characterization of zeolite
2 Y and ZSM-5 from nigerian ahoko kaolin using a novel, lower temperature, metakaolinization
3 technique. J. Mater. Chem. 19 (2009) 6207-6212.
4
5 [27] D.J.C. Yates, Studies on the surface area of zeolites, as determined by physical
6 adsorption and x-ray crystallography. Can. J. Chemistry. 46 (1968) 1695-1701.
7
8 [28] M.M. Rahman, M.B. Awang, A.N.M. Yusof. Preparation, characterization and
9 application of zeolite-Y (Na-Y) for water fitration. Aust. J. Basic Appl. Sci. 6 (2012) 50-55.
PT
10
11 Table 1. Factorial planning 3².
RI
12 Table 2. Percentages obtained by integrating the area of the crystalline peaks for the 9
13 samples of synthesized ZEO-Y-AR.
SC
14 Table 3. Analysis of variance values (ANOVA), model with quadratic correlation (R2)
15 of 0.93.
16 Table 4. Composition in oxides of WM (a), NM (b), a standard sample (ZEO-Y-S) (c)
17
U
and synthesized (d) ZEO-Y-AR (sample 9), (e) ZEO-Y-WM and (f) ZEO-Y-NM.
AN
18 Table 5. Specific surface area of synthesized ZEO-Y and standard sample.
19
M
24 Figure 5. XRD of (a) natural kaolin and (b) metakaolin from natural kaolin, and kaolin
25 from paper sludge (c) and metakaolin from paper sludge (d). .
EP
28 ZEO-Y-S.
29 Figure 8. Micrographies obtained in SEM of the following materials: natural kaolin (a);
AC
30 NM (b); ZEO-Y-S (c); ZEO-Y-AR (sample 9) (d); ZEO-Y-WN (e) and ZEO-Y-NM (f).
31
32
33
34
35
36
37
29
ACCEPTED MANUSCRIPT
1
PT
RI
U SC
AN
M
D
TE
EP
C
AC
ACCEPTED MANUSCRIPT
Table 1
Variables -1 0 +1
A – reaction time (h) 5 6 7
o
B – Temperature ( C) 80 100 120
Experiments Blocks A B
1 1 6 120
2 1 7 100
PT
3 1 5 80
4 2 5 100
RI
5 2 7 120
6 2 6 80
7 3 7 80
SC
8 3 5 120
9 3 6 100
U
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Table 2
Samples 1 2 3 4 5 6 7 8 9
(%) Crystallinity 80,33 90,80 42,72 62,73 76,01 72,41 88,52 85,95 94,25
PT
RI
U SC
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Table 3
Factors SS df MS F p
Time (h) L 680,96 1 680,96 14,0817 0,03306
Time (h) Q 124,08 1 124,08 2,56596 0,20751
Temperature (°C) (L) 248,84 1 248,84 5,14586 0,10808
Temperature (°C) (Q) 136,67 1 136,67 2,82635 0,19132
PT
1L by 2L 776,74 1 776,74 16,0623 0,02787
Error 145,07 3 48,36
RI
SS total 2112,4 8
U SC
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Table 4
PT
Fe2O3 1,64 0,42 < 0,05 < 0,05 0,92 0,29
CaO 2,03 0,06 < 0,05 < 0,05 0,75 <0,05
MgO 1,63 < 0,05 0,05 0,06 0,95 0,09
RI
K 2O 0,48 0,93 0,06 < 0,05 0,23 0,54
Na2O 0,34 0,18 11,71 14,67 14,88 16,42
SC
MnO < 0,05 < 0,05 < 0,05 < 0,05 <0,05 <0.05
P2O5 0,16 0,07 < 0,05 < 0,05 <0,05 <0,05
U
LoI 0,60 0,35 13,68
AN 13,43 16,38 13,63
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Table 5
PT
(d) ZEO-Y-NM 554,9
RI
U SC
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 1
3000 Y
Y Y Y YY Y Y Y Y (9)
Y
0
2000
PT
(8)
0
2000
(7)
RI
0
1000
(6)
SC
Intensity (cps)
2000
0
1000
(5)
U
0
280
AN
(4)
500
M
(3)
2500
(2)
D
0
TE
1000
(1)
0
10 20 30 40 50
2 θ (°)
C EP
AC
ACCEPTED MANUSCRIPT
Figure 2
1Lby2L -4,00778
PT
(1)Time (h)(L) 3,752567
RI
(2)Temperature (ºC)(L) 2,268448
SC
Temperature (ºC)(Q) 1,681174
U
Time (h)(Q) 1,601861
AN
p=,1
Standardized Effect Estimate (Absolute Value)
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 3
Response Surface
Crystallinity (%)
100
PT
90
80
70
RI
Cristallinity (%)
60
50
40
SC
30
20
10
5
12
U
0
12
5
7,
11
2
7,
0
0
11
6,
> 90
8
5
6,
10
AN
Te
6
6,
0
m
10 < 82
4
6,
pe
95 2
6,
ra
h)
0
e( < 72
tu
5,
90
re
Tim
5,
(ºC
85
6
< 62
5,
4
)
80
5,
2
< 52
5,
75
0
4,
M 8
< 42
< 32
< 22
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 4
2350
80 (a)
1636
3450
40
801
464
Transmitance (%)
PT
1083
0
RI
80
2350
465
SC 1595
3450
800
60
1084
40
U (b)
AN
4000 3500 3000 2500 2000 1500 1000 500
-1
Wavenumber (cm )
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 5
800
K
K
(a)
Q
600
PT
Q (b)
Intensity (cps)
400
RI
C
(c)
K P K C C C
SC
200
(d)
U
0
10 20 30 40 50
AN
2θ (°)
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 6
2500
Y
2000
1500
(a) ZEO-Y-WM
1000
Y Y Y Y
Intensity (cps)
PT
500 P Y Y Y YY
YY Y Y
0
2500 10 20 30 40 50
Y
RI
2000
1500
(b)ZEO-Y-NM
SC
1000
Y Y Y Y
500 Y Y Y YY
Y Y
Y Y
U
0
10 20 30 40 50
2 Theta (°)
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 7
60 60
1640
50
457 570
40 40
710
1640
30
1005
PT
3472
563
20
20
467
3470
1000
Transmittance (%)
10
0
04000
RI
3500 3000 2500 2000 1500 1000 50080 2000 1500 1000 500
(c) ZEO-Y-NM 1640 (d) ZEO-Y-S
60
60
1640
SC
40
40
565
1005
570
3470
1005
690
461
20 20
U
3470
460
0
AN
0
Wavernumber (%)
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Figure 8
PT
RI
U SC
AN
M
D
TE
EP
C
AC
ACCEPTED MANUSCRIPT
Highlights
• Synthesis of Y zeolite from analytical reagents, natural kaolin, and kaolin from
paper sludge
• Experimental design to evaluate the time and temperature on the crystallization
• Time was verified to be a key factor in the crystallinity of the Y zeolitic.
• Hydrothermal reaction for the synthesis of Y zeolite is significantly efficient.
PT
RI
U SC
AN
M
D
TE
C EP
AC