Professional Documents
Culture Documents
Indoor Unit Outdoor Unit WH-SDC09H3E8 WH-SDC12H9E8 WH-SDC16H9E8 WH-UD09HE8 WH-UD12HE8 WH-UD16HE8 Destination Europe Turkey
Indoor Unit Outdoor Unit WH-SDC09H3E8 WH-SDC12H9E8 WH-SDC16H9E8 WH-UD09HE8 WH-UD12HE8 WH-UD16HE8 Destination Europe Turkey
Destination
Europe
Turkey
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the products dealt with in this service information by anyone else could result in serious injury or death.
WARNING This indication shows the possibility of causing death or serious injury.
CAUTION This indication shows the possibility of causing injury or damage to properties only.
Symbol with white background denotes item that is PROHIBITED from doing.
Symbol with dark background denotes item that must be carried out.
Carry out test run to confirm that no abnormality occurs after the installation. Then, explain to user the operation, care and
maintenance as stated in instructions. Please remind the customer to keep the operating instructions for future reference.
WARNING
Do not use unspecified cord, modified cord, joint cord or extension cord for power supply cord. Do not share the single outlet with
1.
other electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.
2. Do not tie up the power supply cord into a bundle by band. Abnormal temperature rise on power supply cord may happen.
3. Keep plastic bag (packaging material) away from small children, it may cause suffocation.
4. Do not use pipe wrench to install refrigerant piping. It might deform the piping and cause the unit to malfunction.
5. Do not purchase unauthorized electrical parts for installation, service, maintenance and etc. They might cause electrical shock or fire.
Do not modify the wiring of Indoor Unit for installation of other components (i.e. heater, etc). Overloaded wiring or wire connection
6.
points may cause electrical shock or fire.
7. Do not add or replace refrigerant other than specified type. It may cause product damage, burst and injury etc.
Do not use joint cable for Indoor / Outdoor Unit connection cable. Use specified Indoor / Outdoor Unit connection cable, refer to
instruction CONNECT THE CABLE TO THE INDOOR UNIT and connect tightly for Indoor / Outdoor Unit connection. Clamp the cable
8.
so that no external force will be acted on the terminal. If connection or fixing is not perfect, it will cause heat up or fire at the
connection.
Do not install outdoor unit near handrail of veranda. When installing outdoor unit at veranda of high rise building, child may climb up to
9.
outdoor unit and cross over the handrail and causing accident.
10. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.
11. Do not sit or step on the unit, you may fall down accidentally.
For electrical work, follow local wiring standard, regulation and this installation instruction. An independent circuit and single outlet
12.
must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.
For water circuit installation work, follow to relevant European and national regulations (including EN61770) and local plumbing and
13.
building regulation codes.
Engage dealer or specialist for installation. If installation done by the user is defective, it will cause water leakage, electrical shock or
14.
fire.
This is a R410A model, when connecting the piping, do not use any existing (R22) pipes and flare nuts. Using such same may
cause abnormally high pressure in the refrigeration cycle (piping), and possibly result in explosion and injury. Use only R410A
15. refrigerant.
Thickness or copper pipes used with R410A must be 0.8 mm or more. Never use copper pipes thinner than 0.8 mm.
It is desirable that the amount of residual oil is less than 40mg/10m.
When install or relocate Indoor Unit / Outdoor Unit, do not let any substance other than the specified refrigerant, e.g. air etc. mix into
16.
refrigerant cycle (piping). Mixing of air etc. will cause abnormal high pressure in refrigeration cycle and result in explosion, injury etc..
17. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock or fire.
Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or installation is not
18.
properly done, the set will drop and cause injury.
This equipment is strongly recommended to be installed with Residual Current Device (RCD) on-site according to the respective
19.
national wiring rules or country–specific safety measures in terms of residual current.
During installation, install the refrigerant piping properly before run the compressor. Operation of compressor without fixing
20. refrigeration piping and valves at opened condition will cause suck-in of air, abnormal high pressure in refrigeration cycle and result in
explosion, injury etc.
During pump down operation, stop the compressor before remove the refrigeration piping. Removal of refrigerant piping while
21. compressor is operating and valves are opened will cause suck-in of air, abnormal high pressure in refrigerant cycle and result in
explosion, injury etc.
Tighten the flare nut with torque wrench according to specified method. If the flare nut is over tightened, after a long period, the flare
22.
may break and cause refrigerant gas leakage.
After completion of installation, confirm there is no leakage of refrigerant gas. It may generate toxic gas when the refrigerant contacts
23.
with fire.
Ventilate the room if there is refrigerant gas leakage during operation. Extinguish all fire sources if present. It may cause toxic gas
24.
when the refrigerant contacts with fire.
25. Only use the supplied or specified installation parts, else, it may cause unit vibrate loose, water leakage, electrical shock or fire.
The unit is only for use in closed water system. Utilization in an open water circuit may lead to excessive corrosion of water piping and
26.
risk of incubating bacteria colonies, particularly Legionella, in water.
27. If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and information.
28. Select a location where in case of water leakage, the leakage will not cause damage to other properties.
When installing electrical equipment at wooden building of metal lath or wire lath, in accordance with electrical facility standard, no
29.
electrical contact between equipment and building is allowed. Insulator must be installed in between.
Any work carried out on the Indoor Unit / Outdoor Unit after removing any panels which is secured by screws, must be carried out
30.
under the supervision of authorized dealer and licensed installation contractor.
This unit must be properly earthed. The electrical earth must not be connected to a gas pipe, water pipe, the earth of lightening rod or
31. a telephone. Otherwise there is a danger of electrical shock in the event of an insulation breakdown or electrical earth fault in the
outdoor unit.
Do not use joint cable for outdoor connection cable. Use specified outdoor connection cable, refer to instruction CONNECT THE
32. CABLE TO THE OUTDOOR UNIT and connect tightly for outdoor connection. Clamp the cable so that no external force will be acted
on the terminal. If connection or fixing is not perfect, it will cause heat up or fire at the connection.
CAUTION
Do not install the Indoor Unit / Outdoor Unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates
1.
at surrounding of the unit, it may cause fire.
Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts. Take care of the
2.
liquid refrigerant, it may cause frostbite.
3. Do not install this appliance in a laundry room or other high humidity location. This condition will cause rust and damage to the unit.
4. Make sure the insulation of power supply cord does not contact hot part (i.e. refrigerant piping) to prevent from insulation failure (melt).
Do not apply excessive force to water pipes that may damage the pipes. If water leakage occurs, it will cause flooding and damage to
5.
other properties.
6. Do not touch the sharp aluminium fin, sharp parts may cause injury.
Do not release refrigerant into the atmosphere. The product contains fluorinated greenhouse gases and that its functioning relies upon
7.
such gases.
Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room and damage
9.
the furniture.
11. Ensure the correct polarity is maintained throughout all wiring. Otherwise, it will cause electrical shock or fire.
After installation, check the water leakage condition in connection area during test run. If leakage occurs, it will cause damage to other
12.
properties.
Installation work.
13. It may need two or more people to carry out the installation work. The weight of Indoor Unit / Outdoor Unit might cause injury if carried
by one person.
Note:
Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled indoor water inlet
temperature of 12°C and water outlet temperature of 7°C.
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled indoor water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.
Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and ∆T
= 5°C.
10
11
Note:
Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled indoor water inlet
temperature of 12°C and water outlet temperature of 7°C.
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled indoor water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.
Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and ∆T
= 5°C.
12
13
14
Note:
Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled indoor water inlet
temperature of 12°C and water outlet temperature of 7°C.
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled indoor water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.
Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and ∆T
= 5°C.
15
High Efficiency
Environment Protection
- Non-ozone depletion substances refrigerant (R410A)
Protection Feature
- Random auto restart after power failure for safety restart operation
- Gas leakage protection
- Prevent compressor reverse cycle
- Inner protector to protect compressor
Serviceability Feature
- Breakdown Self Diagnosis function
- System Status Check Buttons for servicing purpose
- System Pumpdown Button for servicing purpose
- Front maintenance design for outdoor unit
16
1 0.2 3
MPa 0.4
bar
4
Buttons / Indicator
3
Quick Menu button
1 (For more details, refer to the separate
Quick Menu Guide.)
10:34am, Mon
Back button
2 1 2
Returns to the previous screen
3 LCD Display 40 ˚c
4
Main Menu button 23 44
For function setup ˚c ˚c 18 ˚c
ON/OFF button
5
Starts/Stops operation 4
2
Operation indicator
6 Illuminates during operation, blinks during
alarm.
1 5
6
Left Right
Press centre
Down
Enter button
Fixes the selected content.
No glove
No pen
17
10:34am, Mon
1 2
5
40 ˚c
1
23 44 6
˚c ˚c 18 ˚c
7
Display
1 Mode selection
AUTO • Depending on the preset outdoor *1, *2 COOL • The fan coil unit is either turned
temperature, the system selects ON or OFF.
HEAT or *1 COOL operation mode. • The outdoor unit provides cooling
Auto Heat Auto Cool to the system.
AUTO • Depending on the preset outdoor *1, *2 COOL • The outdoor unit provides cooling
+ TANK temperature, the system selects + TANK to the system.
HEAT + TANK or *1 COOL + TANK • The system controls the booster
operation mode. heater in the water tank.
Auto Heat Auto Cool
HEAT • The panel/floor HEAT operation is TANK • The water tank is either turned
either turned ON or OFF. ON or OFF.
• The outdoor unit provides heat to • The outdoor unit provides heat to
the system. the water tank.
HEAT • The outdoor unit provides heat to * The direction icons point to the currently
+ TANK the water tank and the system. active mode.
• This mode can be selected only
when the water tank is installed. • Room operation / Tank operation.
• Deice operation.
2 Operation icons
The status of operation is displayed.
Icon will not display (under operation OFF screen) whenever operation is OFF except weekly timer.
Holiday operation status Weekly Timer operation status Quiet operation status
Zone:Room Thermostat Demand Control or
Powerful operation status
→Internal sensor status SG ready or SHP status
Room Heater status Tank Heater status Solar status
Bivalent status
(Boiler)
*1 The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.
*2 Only displayed when COOL mode is unlocked (This means when COOL mode is available).
18
Before starting to install the various menu settings, please initiate the Remote Controller by selecting the language of
operation and installing the date and time correctly.
It is recommended that the installer conducts the following initialization of the Remote Controller.
Selecting the language LCD blinking
Press and wait while the display is
initializing.
After the initial settings have been completed, you can select a quick menu from the following options and edit the setting.
1 Press to display the quick menu.
Select ON/OFF
19
After the initial settings have been completed, you can select a quick menu from the
following options and edit the setting.
10:34am, Mon
1 2
40 ˚c
23 44
˚c ˚c 18 ˚c Select ON/OFF
Quick Menu
Force
Force DHW Powerful Quiet
Heater
Weekly Force
Error Reset R/C Lock
Timer Defrost
20
Powerful
30
• The Powerful mode operates for 30 minutes.
60
• The Powerful mode operates for 60 minutes.
90
• The Powerful mode operates for 90 minutes.
■ Note:
• Powerful is disabled when operation is turned OFF.
21
Select “Yes”.
• Select “Yes” using buttons.
Select “Edit”.
• If you select “Delete”, the timer setting of
the selected pattern will be deleted.
■ Note:
• If the time overlaps with another pattern,
"Set time is overlapped!" will appear on
the screen.
22
23
• Timer is set.
Weekly
Timer After 1 sec delay.
Select “Yes”.
• If you select “No”, the screen will return to the Main Screen.
■ Note:
• Timer is disabled when Force Heater is turned on or Heat-Cool SW is enabled.
• If you have preset the Weekly Timer on 2 zones, you must repeat the same procedure with Zone 2.
24
Force
Defrost
Error Reset
25
1 Function setup
1.1 Weekly timer
Once the weekly timer is set Timer setup
up, User can edit from Quick Select day of the week and
Menu. set the patterns needed
To set up to 6 patterns of (Time / Operation ON/OFF / Mode)
operation on a weekly basis.
Timer copy
• Disabled if Heat-Cool SW is
pressed or if Force Heater
is on. Select day of the week
26
*1 The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised serviceartners.
p
*2 Only displayed when COOL mode is unlocked (This means when COOL mode is available).
27
2.4 Compressor
Shows the compressor
performance.
Select and retrieve
2.5 Heater
Total hours of ON time for
Room heater/Tank heater.
Select and retrieve
3 Personal setup
3.1 Touch sound
Turns the operation sound
ON
ON/OFF.
3.2 LCD contrast
Sets the screen contrast.
3.3 Backlight
Sets the duration of screen
backlight.
1 min
24h
28
3.7 Language
Sets the display language for
ENGLISH / FRANÇAIS /
the top screen.
DEUTSCH / ITALIANO /
ESPAÑOL / DANISH /
• For Dutch, Greek, Finnish SWEDISH / NORWEGIAN /
and Turkish, please refer to
POLISH / CZECH
the English version.
3.8 Unlock password
4 digit password for all the
settings.
0000
4 Service contact
4.1 Contact 1 / Contact 2
Preset contact number for
installer.
Select and retrieve
29
30
31
32
5.11 External SW
No
10 °C Set T ON temperature
Set T OFF
5 °C
temperature
Set Antifreeze
5 °C
temperature
80 °C Set Hi limit
33
No
No
5.15 SG ready
No
Yes
No
5.18 Heat-Cool SW
No
*1 The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised serviceartners.
p
*2 Only displayed when COOL mode is unlocked (This means when COOL mode is available).
34
Heating ON
Compensation temperatures in
curve compensation curve or
direct input.
35
T for heating ON
Temperature for
0 °C
heater ON
Cooling ON
temperatures in
Compensation curve
compensation curve or
direct input.
• If 2 zone system is selected, the 4 temperature points must also be input for Zone 2.
• “Zone 1” and “Zone 2” will not appear on the display if only 1 zone system.
Water temp. for cooling ON Direct
T for cooling ON
*1 The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised serviceartners.
p
*2 Only displayed when COOL mode is unlocked (This means when COOL mode is available).
36
6.3 Auto
Automatic switch from Heat to Outdoor temperatures for switching from Heat
Cool or Cool to Heat. to Cool or Cool to Heat.
6.4 Tank
Setting functions for the tank.
Floor operation time (max) /
• Available only if connected to Tank heat up time (max) /
the tank. Tank re-heat temp. /
Sterilization
Set temperature to
-8 °C perform reboil of tank
water.
37
Sterilization
Sterilization may be set for 1 or
more days of the week.
Sterilization: Time
Time of the selected day(s) of the week to
sterilize the tank.
0:00 ~ 23:59
ON
38
Contact 1 / Contact 2
Contact 1 / Contact 2
Contact name or number.
39
7
1
5-1
2
5-2
3
9 8
40
Air outlet
41
<Top View>
500
340
<Front View> <Side View>
892
980
250
129.5
30.6
49
88.3
58.9 156
141.9
326.9 100
<Bottom View>
424.5
404.1
45
56.1
339.3
51.5
54.6
180
360 69.5
437.3
476
Relative position between the indoor unit and the installation plate <Front View>
Installation
plate
Indoor Unit
body
≥1556 from
756
ground
Bolt -
size M8
Unit: mm
Installation
70 160 200
plate
42
<Top View>
900
355
320
400
20
40
<Side view> <Front View> 900
<Side View>
253 40 320
318.5 218 110
165
243
1340
615
356.5
<Back view>
30
Unit: mm
43
Water
Pressure
Gauge
Expansion
Liquid Vessel
Side Water Capillary
Expansion (3-Way Flow Tube
Strainer Valve Strainer Valve) Switch
Water
Inlet
(Connect
Water to
Refrigerant Pump
Temp. Sanitary
Sensor Tank)
Defrost Water Inlet
Sensor Temp.
Sensor
Pipe
Temp.
Sensor
Heat Control
Air Exchanger Panel
Temp.
Sensor
Muffler
Compressor Discharge
Temp. Sensor
Compressor Tank
Temp. Sensor
Compressor
Model Piping size Rated Length (m) Max Min. Piping Max. Piping Additional
UX09*E5*, UX12*E5*, For Heat For
Elevation Length Length Refrigerant
UD12*E5*, Gas Liquid Pump Indoor Hydromodule
(m) (m) (m) (g/m)
UD16*E5*, UX09*E8*, Unit + Tank
UX12*E8*,
UX16*E8*, UD09*E8*, Ø15.88 mm Ø9.52 mm
UD12*E8*, (5/8") (3/8")
7 5 20 3 30 50
UD16*E8*
Example:
If piping length is 30m, the quantity of additional refrigerant should be 1000g. [(30-10)m x 50 g/m = 1000g]
GWP (R410A) = 2088
44
Expansion
Vessel (10L) External Internal
Thermostat Thermostat
Fan Coil Unit
Indoor Unit Air purge valve (Heating / Cooling)
T
TH
Water
Inlet External Nothing
Pressure Thermistor
Gauge
Panel Heater Unit
OLP × 4 (Heating)
3-Way valve 2-Way valve
Extra Pump
Water
Flow
Sensor
HEX
Floor Heating Panel
Pump (Heating)
TH
Water
Outlet TH
Water Outlet 2 OLP
THt Heater
Heater:
OD 9kW series: 3kW
OD 16kW series: 6kW
WATER
R410A Cold Water
Outdoor Unit Supply
R410A
DHW Tank
Buffer
Zone1
Tank Zone1
Mixing Fan Coil Unit Room Thermo (4 option )
Water Temp (Heating / Cooling)
Valve Pump Thermistor
Buffer
Tank
Thermistor
External Internal
Indoor Unit Thermostat Thermostat
2-Way valve
3-Way valve Panel Heater Unit
(Heating)
T
External Without
Thermistor
FloorHeating Panel
Zone2 Zone2
Mixing Fan Coil Unit Room T hermo (4 option )
OLP Solar Water Temp (Heating / Cooling)
THt Valve Pump Thermistor
Panel
Thermistor
Heater
External Internal
Thermostat Thermostat
Outdoor Unit 2-Way valve
Panel Heater Unit
(Heating)
T
External Without
Thermistor
DHW Tank
Hex
T
Pool Pool
Addtional Pump Thermistor
Outdoor Sensor
45
L2 FUSE1 SUB
RELAY
L3
N RY-V2 RY-V3
SSR1 SSR200 SSR201 SSR202 SSR203 SSR204 SSR205 SSR206 SSR207 PTC
SC M
CIRCUIT
NOISE FILTER
POWER SUPPLY 1
WATER
WATER PUMP
3-phase M M M M M M M M
PUMP 1~ 1~ M RELAY
AC400V 50Hz 1~ 1~ 1~ 1~ 1~ 1~ 1~ FUSE201 REACTOR REACTOR
1
WH-SDC09H3E8 WH-UD09HE8
46
FUSE2 3~
5
RECTIFICATION CIRCUIT
RY-HT (L1)
RY-PWR2
RY-HT1
RY-HT2
RY-HOT
RY-HT (L2)
SC
FUSE3
CIRCUIT
RY-HT (L3)
RECTIFICATION
NOISE FILTER
HEATER
HEATER
FUSE2
4-WAY VALVE
BACKUP HEATER
M M
CIRCUIT
ELCB
RECTIFICATION
RY-BOOSTER
L
BOOSTER HEATER
N
POWER SUPPLY 2
NOISE FILTER
1-phase
AC230V 50Hz
7.2
RCCB
L1
L2 FUSE1 SUB
RELAY
L3
N RY-V2 RY-V3
SSR1 SSR200 SSR201 SSR202 SSR203 SSR204 SSR205 SSR206 SSR207 PTC
SC M
CIRCUIT
NOISE FILTER
POWER SUPPLY 1
WATER
WATER PUMP
3-phase M M M M M M M M
PUMP 1~ 1~ M RELAY
AC400V 50Hz 1~ 1~ 1~ 1~ 1~ 1~ 1~ FUSE201 REACTOR REACTOR
1
2-WAYS 3-WAYS EXTRA WATER WATER POOL SOLAR MIXING MIXING
VALVE VALVE PUMP PUMP PUMP WATER WATER VALVE VALVE 2
ZONE1 ZONE2 PUMP PUMP ZONE1 ZONE2 NOISE
FUSE202 FILTER
3
FUSE203
4 MS
FUSE2 3~
47
5
RECTIFICATION CIRCUIT
RY-PWR2
RY-HT1
RY-HT2
RY-HOT
RY-HT (L1)
SC
L1
RY-HT (L3)
RECTIFICATION
NOISE FILTER
L2
HEATER
HEATER
4-WAY VALVE
BACKUP HEATER M M
L3
CIRCUIT
FUSE2
RECTIFICATION
POWER SUPPLY 3
NOISE FILTER
3-phase
AC400V 50Hz
RY-BOOSTER
BOOSTER HEATER
WH-SDC12H9E8 WH-UD12HE8 WH-SDC16H9E8 WH-UD16HE8
8.1
8.1.1
BL OLP BL
80±3°C
1 1 OLP
80±3°C
2 2 BR OLP BR 2 2 W
O 80±3°C O W
REACTOR 3 3 3 3
GR
4 4 1 1 W
RCCB W W
R
(LA1) 2 1 B BR Y O R
G BL BACKUP HEATER
B
(LA2) 2 1
W W W TERMINA L
Y A BOARD
(LA3)
AC1-L1 L2 L1 G03 FUSE2
BL 20A 500V AC2-N1
B (BLU) (WHT) (WHT) (GRN)
(BLK)
(BLU)
(G RY)
(YLW)
(N)
(RED)
(ORG)
(WHT)
(BRW)
HT1-L1
HT1-L2
HT1-L3
AC2-L1
AC2-L2
AC2-L3
AC2-N2
Indoor Unit
ACL3 RCCB/ELCB
W SIGNAL FUSE3 (BLK) BL (L1)
400V 25A DETECTION T3.15 A L250V
NOISE LJP2
l∆n=30mA AC1-L2 CIRCUIT (WHT)
POWER SUPPLY 1
FILTER W (N1)
Y (YLW)
3~phaseAC400V 50Hz
RY-HT (L1)
RY-HT (L2)
RY-HT (L3)
CIRCUIT CN6
WH-SDC09H3E8
FUSE1
AC1-L3 T6.3 A L250V 230V 30A~40A
BL (BLK) RECTIFICATION OLP BOOSTER
l∆n=30mA
POWER SUPPLY 2
RY-BOOSTER
CIRCUIT
CIRCUIT ROOM TEMP.
ZONE 1 GROUNDING
TERMINAL AC1-N
1 SW1 SW2
OUTDOORAIR
G01 SENSOR
G (GRN)
2
TANK
DATA
R (RED)
COMMUNICATION SENSOR
3 CIRCUIT
G02 ELECTRONIC CONTROLLER
G (GRN) CN4
4 (MAIN)
EXTERNAL
CONTROL 1
TO OUTDOOR UNIT
8. Wiring Connection Diagram
5 NOISE
RECTIFICATION BL
CN-PUMP1 FILTER CONTROL
(WHT)
CIRCUIT CIRCUIT BL PANEL
W 7 7 W 1
M BL 4 4 BL 4
GROUNDING WATER R 3 3 R 5 CN3
PUM P
WATER RY-CON TACT1
BR 2 2 BR 6
PUMP
48
B 1 1 B 7 BOILER
CIRCUIT CONTACT
SSR1
G G
EXTRA
WATER BASE PAN WATER CONNECTING PUMP
PIPING PIPING BAR
BOOSTER
MIXING MIXING HEATER
ROOM THERMO 2 ROOM THERMO 1 VALVE 1 VALVE 2
L N COO L HEAT L N COO L HEAT N OPEN CLOSE N OPEN CLOSE
OLP
80±3°C
B
CN-OLP1 1
(WHT) 2
B
RY-V2
RY-V3
CN201 W
5
CN209 CN202 CN203 1 BR
W 1
POOL WATER CN-COMM 3 CN-CN T W
W (WHT) CN-F LWSEN FLOW
SSR202 SIGNAL SIGNAL (YLW) W B
PUMP 4 1 (WHT) BL SENSOR
DETECTION DETECTION W 4
CN-PWR202 1 1 CN-PWR2
CIRCUIT CIRCUIT (YLW) W
SOLAR WATER 2 2 (BLU)
SSR204
SSR205
SSR206
SSR207
SSR203 ACN (WHT) W 1 1
PUMP ACL (BLK) CN-PWR (BLK)
t° WATER OUTLET TEMP. SENSOR (THERMISTOR)
BL
SIGNAL CN-TH1
3 (WHT) t° REFRIGERANT TEMP. SENSOR (THERMISTOR)
ERROR W DETECTION
RY1 1 2 CN-PWR4
SIGNAL CN-PWR204 2 W CIRCUIT 6 t° WATER INLET TEMP. SENSOR (THERMISTOR)
1 (BLK)
(YLW) 3
CN208
WATER PUMP B 3 CN-PWR3 CN-TH3 1
DCN (BLU) t° HEX WATER OUTLET TEMP. SENSOR (THERMISTOR)
ZONE 1 SSR200 R (WHT) 2
ELECTRONIC CONTROLLER DC P (RED) 1 (GRN)
CN1 CN2
WATER PUMP (SUB)
ZONE 2 SSR201
1
REMARKS:
CN-CN T CLOSE OPEN N CLOSE OPEN N HEAT COOL N L W : WHITE
(WHT) 2-WAY 3-WAY ROOM THERMO 1 O : ORANGE
5 CN205 CN204 CN207 CN206 CN210 VALVE VALVE BLUE
ORANGE WHITE
R : RED
B : BLUE
BLACK WHITE
BLUE 3 1 BL : BLACK
BROWN Y : YELLOW
ORANGE 2 2
DC DC VCC BIT2 BIT1 BLACK
BR : BROWN
GND 10V BROWN 1 3 G : GREEN
RED
WHITE
SG
ORANGE GR : GRAY
ZONE 2
ZONE 1
ZONE 2
ZONE 1
SWITCH
SENSOR
SENSOR
SENSOR
Y/G : YELLOW/GREEN
COMP. SW
EXTERNAL
SIGNAL
SIGNAL
HEAT/COOL
POOL TEMP.
ROOM TEMP.
ROOM TEMP.
LEAD WIRE FIXING FOR HEATER
DEMAND
OPTIONAL BROWN ELCB : EARTH LEAKAGE CIRCUIT BREAKER
SOLAR TEMP.
WATER TEMP.
WATER TEMP.
BUFFERTANK
LEAD WIRE FIXING FOR OLP
RCCB
BL OLP BL (LB1)
80±3°C
8.1.2
1 1 OLP (LB2)
80±3°C
2 2 BR OLP BR 2 2 W
O 80±3°C O W (LB3)
REACTOR 3 3 3 3
4 4 1 1 W
RCCB W W (N)
R
(LA1) B 2 1 B BR Y O R BL
G BL BACKUP HEATER GR
(LA2) Y 2 1 400V 25A~40A
W W W TERMINA L l∆n=30mA
POWER SUPPLY 2
A B BOARD
3~phaseAC400V 50Hz
(LA3) BL
AC1-L1 L2 L1 G03 FUSE2
20A 500V AC2-N1
B (BLU) (WHT) (WHT) (GRN)
(BLK)
(BLU)
(GRY)
(YLW)
(RED)
(N) W
(ORG)
(WHT)
(BRW)
HT1-L1
HT1-L2
HT1-L3
AC2-L1
AC2-L2
AC2-L3
AC2-N2
ACL3
SIGNAL FUSE3 (BLK) BL GROUNDING
400V 25A DETECTION T3.15 A L250V
NOISE
l∆n=30mA AC1-L2 CIRCUIT
POWER SUPPLY 1
Y (YLW) FILTER
3~phaseAC400V 50Hz
RY-HT (L1)
RY-HT (L2)
RY-HT (L3)
CIRCUIT CN6
FUSE1
AC1-L3 T6.3 A L250V
BL (BLK) RECTIFICATION OLP BOOSTER
CIRCUIT SIGNAL HEATER
GROUNDING NOISE FILTER
CIRCUIT DETECTION
CIRCUIT ROOM TEMP.
RY-BOOSTER
TERMINAL AC1-N
BOARD W (WHT)
CN5
1 SW1 SW2
OUTDOORAIR
G01 SENSOR
G (GRN)
2
TANK
DATA
R (RED)
COMMUNICATION SENSOR
3 CIRCUIT
G02 ELECTRONIC CONTROLLER
G (GRN) CN4
4 (MAIN)
EXTERNAL
CONTROL 1
TO OUTDOOR UNIT
5 NOISE
RECTIFICATION BL
FILTER
WH-SDC12H9E8 WH-SDC16H9E8
M BL 4 4 BL 4
GROUNDING WATER R 3 3 R 5 CN3
PUM P
WATER RY-CON TACT1
BR 2 2 BR 6
49
B 1 1 B 7
PUMP BOILER
CIRCUIT CONTACT
SSR1
G G
EXTRA
WATER BASE PAN WATER CONNECTING PUMP
PIPING PIPING BAR
BOOSTER
MIXING MIXING HEATER
ROOM THERMO 2 ROOM THERMO 1 VALVE 1 VALVE 2
L N COO L HEAT L N COO L HEAT N OPEN CLOSE N OPEN CLOSE
OLP
80±3°C
B
CN-OLP1 1
(WHT) 2
B
RY-V2
RY-V3
CN201 W
5
CN209 CN202 CN203 1 BR
W CN-CN T 1
POOL WATER CN-COMM 3 W
W (WHT) CN-F LWSEN FLOW
SSR202 SIGNAL SIGNAL (YLW) W B
PUMP 4 1 (WHT) BL SENSOR
DETECTION DETECTION W 4
CN-PWR202 1 1 CN-PWR2
CIRCUIT CIRCUIT (YLW) W
SOLAR WATER 2 2 (BLU)
SSR204
SSR205
SSR206
SSR207
SSR203 ACN (WHT) W 1 1
PUMP ACL (BLK) CN-PWR (BLK)
t° WATER OUTLET TEMP. SENSOR (THERMISTOR)
BL
SIGNAL CN-TH1
3 (WHT) t° REFRIGERANT TEMP. SENSOR (THERMISTOR)
ERROR W DETECTION
RY1 1 2 CN-PWR4
SIGNAL CN-PWR204 2 W CIRCUIT 6 t° WATER INLET TEMP. SENSOR (THERMISTOR)
1 (BLK)
(YLW) 3
CN208
WATER PUMP B 3 CN-PWR3 CN-TH3 1
DCN (BLU) t° HEX WATER OUTLET TEMP. SENSOR (THERMISTOR)
ZONE 1 SSR200 R (WHT) 2
ELECTRONIC CONTROLLER DC P (RED) 1 (GRN)
CN1 CN2
WATER PUMP
(SUB)
ZONE 2 SSR201
1
REMARKS:
CN-CN T CLOSE OPEN N CLOSE OPEN N HEAT COOL N L W : WHITE
(WHT) 2-WAY 3-WAY ROOM THERMO 1 O : ORANGE
5 CN205 CN204 CN207 CN206 CN210 VALVE VALVE BLUE
ORANGE WHITE
R : RED
B : BLUE
BLACK WHITE
BLUE 3 1 BL : BLACK
BROWN Y : YELLOW
ORANGE 2 2
DC DC VCC BIT2 BIT1 BLACK
BR : BROWN
GND 10V BROWN 1 3 G : GREEN
RED
WHITE
SG
ORANGE GR : GRAY
ZONE 2
ZONE 1
ZONE 2
ZONE 1
SWITCH
SENSOR
SENSOR
SENSOR
Y/G : YELLOW/GREEN
COMP. SW
EXTERNAL
SIGNAL
SIGNAL
HEAT/COOL
POOL TEMP.
ROOM TEMP.
ROOM TEMP.
LEAD WIRE FIXING FOR HEATER
DEMAND
OPTIONAL BROWN ELCB : EARTH LEAKAGE CIRCUIT BREAKER
SOLARTEMP.
WATER TEMP.
WATER TEMP.
BUFFERTANK
LEAD WIRE FIXING FOR OLP
8.2
MAGNETIC RELAY
GR 4 2 W REACTOR
PTC R R
O 8 6 O O
1 0
1
MAGNETIC RELAY W W
31 32 2
REACTOR
B B
G G G BL 2 2
R U
1 1 W
2
L1-IN FUSE201 L1-OUT O T W O
B (BLU) 20A 500V (BLU) B
REACTOR
REACTOR Y Y
L2-IN L2-OUT A1 A2 BL BL
Y (YLW) (YLW) Y
L3-IN FUSE202 L3-OUT W
BL (BLK) 20A 500V NOISE FILTER CIRCUIT (BLK) BL W REACTOR W
N-OUT 1
N-IN FUSE203 W
W (WHT) 20A 500V (WHT) W W W
3 1 CN-RY2 2 1 CN-RY1
N-IN
L3-L
L2-L
L1-L
L3-IN
L2-IN
(GREEN) (WHITE)
L3-P1
L2-P1
L1-P1
L1-P2
L2-P2
L3-P2
(RED)
(RED)
(BLUE)
(BLUE)
YELLOW
(GRAY)
L3-OUT
L2-OUT
(WHITE)
(WHITE)
(BLACK)
(BLACK)
(YELLOW)
(YELLOW)
(YELLOW)
(ORANGE)
(ORANGE)
1 BL 1
HIGH PRESSURE 2 CN-HPS
SENSOR W
3 3 (RED)
R
4
FUSE2
RY-PWR2
CIRCUIT
T3.15A L250V
BLUE RED
RECTIFICATION
CN-V1
(YELLOW)
50
TRADEMARK
1 RY-V1
ELECTRO
MAGNETIC COIL RECTIFICATION COMPRESSOR TERMINAL
(2-WAY VALVE) CIRCUIT
3
FUSE3
CN-HOT
(BLUE) T3.15A L250V
1 RY-HOT
ELECTRO
MAGNETIC COIL
(4-WAY VALVE) SWITCHING POWER
3 SUPPLY CIRCUIT RECTIFICATION P
CIRCUIT (RED) U R MS
CN-HT1 U 3~
(WHITE) (BLUE) V B
V
1 RY-HT1 (YELLOW) W Y
COMPRESSOR W
CRANKCASE N
HEATER COMPRESSOR
3 1
ELECTRONIC CONTROLLER (MAIN) CN-FM1
1 RY-HT2 (WHITE) 4 M
TERMINAL BASE PAN UPPER FAN MOTOR
BOARD CN-HT2
HEATER (BLACK)
1 3 7
(OPTIONAL)
1
2
BL AC-BLK02 CN-FM2
3 (BLACK) COMMUNICATION (RED) 4 M LOWER FAN MOTOR
TO CIRCUIT
INDOOR W AC-WHT02
UNIT 4 (WHITE)
R COM3 7
5 (RED) CN-TANK CN-DIS CN-TH1 CN-TH2 CN-TH3 CN-EV1 CN-PSW1
(WHITE) (WHITE) (WHITE) (BLUE) (YELLOW) (WHITE) (BLUE)
1 3 1 2 1 4 1 2 1 2 1 6 1 2
Y/G
t° t° t° t° t° t° R
R
M
(THERMISTOR)
(THERMISTOR)
(THERMISTOR)
(THERMISTOR)
(THERMISTOR)
(THERMISTOR)
BL : BLACK Y : YELLOW
BR : BROWN O : ORANGE
G : GREEN GR : GRAY
Y/G : YELLOW/GREEN COMPRESSOR (TANK) TEMP. SENSOR
OUTDOOR PIPE (COND.) TEMP. SENSOR
(BLK)
(BLU)
(N) (GRY)
(YLW)
(RED)
(ORG)
(WHT)
(BRW)
HT1-L1
HT1-L2
HT1-L3
AC2-L1
AC2-L2
AC2-L3
AC2-N2
ACL3
RCCB/ELCB
W SIGNAL FUSE3 (BLK) BL (L1)
400V 25A DETECTION T3.15 A L250V
NOISE LJP2
l∆n=30mA AC1-L2 CIRCUIT (WHT)
POWER SUPPLY 1
FILTER W (N1)
Y (YLW)
3~phaseAC400V 50Hz
RY-HT (L1)
RY-HT (L2)
RY-HT (L3)
WH-SDC09H3E8
CIRCUIT 12V
FUSE1 5V 5V
AC1-L3 T6.3 A L250V 230V 30A~40A
BL (BLK) RECTIFICATION
R143 R141 CN6 l∆n=30mA
OLP BOOSTER
RY-BOOSTER
CIRCUIT 50V
CIRCUIT HEATER
GROUNDING
TERMINAL AC1-N
BOARD W (WHT) ROOM TEMP.
ZONE 1
C83 R136
1 0.1µ 1k
SW1 SW2 16V
G01 CN5
G (GRN)
2 OUTDOORAIR
DATA C98 C89 SENSOR
R (RED)
COMMUNICATION ELECTRONIC CONTROLLER 1µ 1µ
3 CIRCUIT 16V 16V
(MAIN) TANK
G02 G2 G2
G (GRN)
SENSOR
4
9. Electronic Circuit Diagram
G2
TO OUTDOOR UNIT
5 NOISE 5V
CN4
RECTIFICATION FILTER
CN-PUMP1 CIRCUIT
(WHT) CIRCUIT PC1
EXTERNAL
4 1 CONTROL 1
W 7 7 W 1
K
3 2 ZD2 R1 BL
C123 20V 10k
A
M BL 4 4 BL 4 1µ CONTROL
GROUNDING WATER R 3 3 R 5 WATER 50V BL PANEL
PUM P R24
BR 2 2 BR 6 10k
B 1 1 B 7
PUMP
CIRCUIT
51
C93 CN3
G G LF3 100p RY-CON TACT1
50V BOILER
WATER BASE PAN WATER CONNECTING
PIPING PIPING BAR CONTACT
SSR1
MIXING MIXING EXTRA
ROOM THERMO 2 ROOM THERMO 1 VALVE 1 VALVE 2 PUMP
L N COO L HEAT L N COO L HEAT N OPEN CLOSE N OPEN CLOSE
5V_2 5V BOOSTER
HEATER
L4
R81 R86 *RY-HTL3
CN201 W 5 10k 10k 12V OLP
CN209 CN202 CN203 *RY-HTL2 80±3°C
1 W 3
POOL WATER CN-COMM W 1 B
SSR202 C63 *RY-HTL1
PUMP (YLW) W 1 1000p 5V 2
SIGNAL SIGNAL 4
50V B
DETECTION DETECTION CN-OLP1
SOLAR WATER CIRCUIT CIRCUIT CN-CN T 5V (WHT)
(WHT)
SSR204
SSR205
SSR206
SSR207
PUMP SSR203
ACN (WHT) W 1 C88 C91
ACL (BLK) CN-PWR (BLK) 1µ 220µ
BL 16V 10V C92
ERROR 3 0.1µ
RY1 16V 1 BR
SIGNAL 5V_2 G2
RY-V2
RY-V3
2 W FLOW
CN208 SIGNAL 3 B
W 2 R128 R132 R135 R139 R140 4 BL SENSOR
WATER PUMP 1 DETECTION
CN-PWR204 2 W 20k 820 20k 20k 20k R130
ZONE 1 SSR200 1 CIRCUIT 1% 1% 1% 1% 1% CN-F LWSEN
(YLW) 3 10k
CN-PWR4 (WHT)
(BLK) 1
WATER PUMP 20V 2 t° WATER OUTLET TEMP. SENSOR (THERMISTOR)
ZONE 2 SSR201 ELECTRONIC CONTROLLER 3
B 3 4 t° REFRIGERANT TEMP. SENSOR (THERMISTOR)
(SUB) DCN (BLU)
R 5
DC P (RED) 6 t° WATER INLET TEMP. SENSOR (THERMISTOR)
1
CN-PWR3
1 (GRN) CN-TH1
(WHT)
CN-CN T 1
CN-PWR202 1 W 1
(WHT)
(YLW) W 2 t°
2 HEX WATER OUTLET TEMP. SENSOR (THERMISTOR)
5 2 C73 C79 C81 C84 C90
CN205 CN204 CN207 CN206 CN210 CN-PWR2 G6 1µ 1µ 1µ 1µ 1µ CN-TH3
(BLU) 16V 16V 16V 16V 16V G2 (WHT)
G2
CN1 CN2
SG
ZONE 2
ZONE 1
ZONE 2
ZONE 1
CLOSE OPEN N CLOSE OPEN N HEAT COOL N L
SWITCH
SENSOR
SENSOR
SENSOR
COMP. SW ROOM THERMO 1
EXTERNAL
2-WAY 3-WAY
SIGNAL
SIGNAL
HEAT/COOL
POOL TEMP.
ROOM TEMP.
ROOM TEMP.
DEMAND
OPTIONAL VALVE VALVE
SOLARTEMP.
WATER TEMP.
WATER TEMP.
BUFFERTANK
9.1.2
RCCB
BL OLP (LB1)
80±3°C
1 1 OLP (LB2)
80±3°C
2 2 BR OLP BR 2 2 W
O 80±3°C O W (LB3)
REACTOR 3 3 3 3
4 4 1 1 W
RCCB W W (N)
R
(LA1) 2 1 B BR Y O R BL
G BL BACKUP HEATER GR
B 400V 25A~40A
(LA2) 2 1
W W W TERMINA L l∆n=30mA
POWER SUPPLY 2
Y A B BOARD
3~phaseAC400V 50Hz
(LA3)
AC1-L1 L2 L1 G03 FUSE2
BL 20A 500V AC2-N1
B (BLU) (WHT) (WHT) (GRN)
(BLK)
(BLU)
(GRY)
(YLW)
(N)
(RED)
(ORG)
(WHT)
(BRW)
HT1-L1
HT1-L2
HT1-L3
AC2-L1
AC2-L2
AC2-L3
AC2-N2
ACL3
W SIGNAL FUSE3 (BLK) BL GROUNDING
400V 25A DETECTION T3.15 A L250V
NOISE
AC1-L2 CIRCUIT
POWER SUPPLY 1
l∆n=30mA FILTER
Y (YLW)
3~phaseAC400V 50Hz
RY-HT (L1)
RY-HT (L2)
RY-HT (L3)
CIRCUIT 12V
FUSE1 5V 5V
AC1-L3 T6.3 A L250V
BL (BLK) RECTIFICATION
SIGNAL R143 R141 CN6
GROUNDING NOISE FILTER CIRCUIT 6.49k 6.49k C121
CIRCUIT DETECTION 1% 1% 1µ OLP BOOSTER
CIRCUIT 50V
HEATER
RY-BOOSTER
TERMINAL AC1-N
BOARD W (WHT) ROOM TEMP.
ZONE 1
TO OUTDOOR UNIT
5 NOISE 5V
CN4
RECTIFICATION FILTER
CN-PUMP1 CIRCUIT
(WHT) CIRCUIT EXTERNAL
WH-SDC12H9E8 WH-SDC16H9E8
PC1
4 1 CONTROL 1
W 7 7 W 1
K
3 2 ZD2 R1 BL
C123 20V 10k
A
M BL 4 4 BL 4 1µ CONTROL
GROUNDING WATER R 3 3 R 5 WATER 50V BL PANEL
PUM P R24
BR 2 2 BR 6 10k
B 1 1 B 7
PUMP
CIRCUIT
52
C93 CN3
G G LF3 100p RY-CON TACT1
50V BOILER
WATER BASE PAN WATER CONNECTING
PIPING PIPING BAR CONTACT
SSR1
MIXING MIXING EXTRA
ROOM THERMO 2 ROOM THERMO 1 VALVE 1 VALVE 2 PUMP
L N COO L HEAT L N COO L HEAT N OPEN CLOSE N OPEN CLOSE
5V_2 5V BOOSTER
HEATER
L4 12V
R81 R86 *RY-HTL3
CN201 W 5 10k 10k 12V OLP
CN209 CN202 CN203 *RY-HTL2 80±3°C
1 W 3
POOL WATER CN-COMM W 1 B
C63 *RY-HTL1
PUMP SSR202 (YLW) W 1 2
SIGNAL SIGNAL 4 1000p 5V
50V B
DETECTION DETECTION CN-OLP1
SOLAR WATER CIRCUIT CIRCUIT CN-CN T 5V (WHT)
(WHT)
SSR204
SSR205
SSR206
SSR207
PUMP SSR203
ACN (WHT) W 1 C88 C91
ACL (BLK) CN-PWR (BLK) 1µ 220µ
BL 16V 10V C92
ERROR 3 0.1µ
RY1 16V 1 BR
SIGNAL 5V_2 G2
RY-V2
RY-V3
2 W FLOW
CN208 SIGNAL 3 B
W 2 R128 R132 R135 R139 R140 4 BL SENSOR
WATER PUMP 1 DETECTION
CN-PWR204 2 W 20k 820 20k 20k 20k R130
ZONE 1 SSR200 1 1% 1% 1% 1% 1% CN-F LWSEN
(YLW) 3
CIRCUIT 10k
CN-PWR4 (WHT)
(BLK) 1
WATER PUMP 20V 2 t° WATER OUTLET TEMP. SENSOR (THERMISTOR)
ZONE 2 SSR201 ELECTRONIC CONTROLLER 3
B 3 4 t° REFRIGERANT TEMP. SENSOR (THERMISTOR)
(SUB) DCN (BLU)
R 5
DC P (RED) 6 t° WATER INLET TEMP. SENSOR (THERMISTOR)
1
CN-PWR3
1 (GRN) CN-TH1
(WHT)
CN-CN T 1
CN-PWR202 1 W 1
(WHT)
(YLW) W 2 t°
2 HEX WATER OUTLET TEMP. SENSOR (THERMISTOR)
5 2 C73 C79 C81 C84 C90
CN205 CN204 CN207 CN206 CN210 CN-PWR2 G6 1µ 1µ 1µ 1µ 1µ CN-TH3
(BLU) 16V 16V 16V 16V 16V G2 (WHT)
G2
CN1 CN2
SG
ZONE 2
ZONE 1
ZONE 2
ZONE 1
CLOSE OPEN N CLOSE OPEN N HEAT COOL N L
SWITCH
SENSOR
SENSOR
SENSOR
COMP. SW
ROOM THERMO 1
EXTERNAL
2-WAY 3-WAY
SIGNAL
SIGNAL
HEAT/COOL
POOL TEMP.
ROOM TEMP.
ROOM TEMP.
DEMAND
OPTIONAL VALVE VALVE
SOLAR TEMP.
WATER TEMP.
WATER TEMP.
BUFFERTANK
MAGNETIC RELAY REACTOR
GR 4 2 W R R
9.2
PTC
O 8 6 O O
1 0 1
MAGNETIC RELAY
2
31 32 W W
REACTOR
B B
G G G BL 2 2
R U
1 1 W
L1-IN FUSE201 O O 2
L1-OUT T W
B (BLU) 20A 500V (BLU) B REACTOR
REACTOR Y Y
L2-IN L2-OUT A1 A2 BL BL
Y (YLW) (YLW) Y
L3-IN FUSE202 L3-OUT W
BL (BLK) 20A 500V NOISE FILTER CIRCUIT (BLK) BL W REACTOR W
1
Outdoor Unit
N-IN
L3-L
L2-L
L1-L
L3-IN
L2-IN
(GREEN) (WHITE)
L3-P1
L2-P1
L1-P1
L1-P2
L2-P2
L3-P2
(RED)
(RED)
(BLUE)
(BLUE)
(GRAY)
L3-OUT
L2-OUT
CN-HPS
(WHITE)
(BLACK)
(WHITE)
(BLACK)
13V
(YELLOW)
(RED)
(YELLOW)
(YELLOW)
(ORANGE)
(ORANGE)
1 BL 1
HIGH 2
PRESSURE 2 5V
W 3 R358
SENSOR 3 20k
FUSE2
R 4 RY-PWR2
CIRCUIT
13V
T3.15A L250V
C213 C169
RECTIFICATION
1µ 220µ 5V VccFM
16V 10V IC9
VCC R318
9
16 1 7.5k
CN-V1 4 PC12 1
FUSE3
15 2
(YELLOW
T6.3A L250V
P
1 RY-V1 14 3 (RED) U R MS
ELECTRO U 3~
13 4 RECTIFICATION (BLUE) V B
MAGNETIC COIL RECTIFICATION V
(2-WAY VALVE) 12 5 3 2 VccFM CIRCUIT Y
3 CIRCUIT (YELLOW) W
*R164 W
11 6 N
CN-HOT VccFM COMPRESSOR
(BLUE) 10 7 Q27 e
1 RY-HOT GND 8 1
ELECTRO 10k
53
1 PC13 4 b CN-FM1
MAGNETIC COIL C78 UPPER
(4-WAY VALVE) SWITCHING POWER 4.7k 0.47µ (WHITE) 4 M FAN
C72 630V
3 SUPPLY CIRCUIT 13V 1000P c 5 MOTOR
50V R168 R170 6
CN-HT1 4.42k 10.0k
(WHITE) IC7 7
VCC 2 3
9 1% 1%
1 RY-HT1 1 16
COMPRESSOR G3
CRANKCASE 2 15 R172 C74 R392 C80 5V VccFM
HEATER 5.11k 10µ 200k 0.047µ
3 14 1% 50V 25V
3 C160 R376
0.01µ 4 13 7.5k
CN-HT2 13V 4 PC10 1
(BLACK) 5 12
TERMINAL 1 RY-HT2 6 11 IC8
VCC
BOARD BASE PAN 9
7 10 1 16
HEATER 13V
1 C159 2 15 3 2
3 0.01µ 8 GND
(OPTIONAL) 3 14 *R370 1
2 BL VccFM CN-FM2
AC-BLK02 4 13
(RED) 4 M LOWER
TO 3 (BLACK) 5 12 FAN
W AC-WHT02 C157 5 MOTOR
INDOOR COMMUNICATION 0.01µ 6
4 6 11
UNIT (WHITE) CIRCUIT 7
R COM3 7 10
D33
D34
D35
D36
5 C84 C185
(RED) 8 GND R375 0.047µ
0.047µ 200k
C158 25V 25V
0.01µ
Y/G 5V
5V G3
G2
t° t° t° t° t° t° R
(50kΩ, 3950)
(50kΩ, 3950)
(15kΩ, 3950)
R
(4.96kΩ, 3800)
(4.96kΩ, 3800)
(4.96kΩ, 3800)
M
DEFROST TEMP.
EVA EXIT TEMP.
DISCHARGE TEMP.
ELECTRO MAGNETIC COIL
SENSOR (THERMISTOR)
SENSOR (THERMISTOR)
SENSOR (THERMISTOR)
SENSOR (THERMISTOR)
SENSOR (THERMISTOR)
SENSOR (THERMISTOR)
AC2-L1 AC1-L1
AC2-L2 HT1-L2 HT1-L1 AC1-L2
AC2-N2 G02
CN-OLP1
HT1-L3
AC2-L3
AC2-N1 G03
G01
CN1
DATA
AC1-N
AC1-L3
CN-FLWSEN
CN2
CN-TH1
CN-TH3
CN-CNT
54
55
CN-FM1
CN-FM2
CN-V1
CN-HOT
CN-RY2
CN-HT1
CN-TH2
CN-HT2
CN-PSW1
CN-RY1
CN-TH3
CN-TH1
CN-TANK CN-EV2
CN-HPS
CN-DIS CN-EV1
56
L1-OUT
FG202
L2-OUT
L3-OUT
N-OUT
N-IN L3-IN
57
Wall
100 mm
or more Indoor Outdoor
15 mm
100 mm 100 mm
or more or more Sleeve for tube
assembly
Approx. 5 - 7 mm
(Unit in mm)
11.1.4.1 Access to Internal Components
More than 375 More than 375
Wall 5 5
Wall
WARNING
Indoor Unit
body Please follow the steps below for take out front plate.
≥1556 from Before removing the front plate of indoor unit, always
756
ground
switch off all power supply (i.e. indoor unit power
supply, heater power supply and Tank Unit power
supply).
Bolt -
size M8 1. Remove the 2 mounting screws which located at
bottom of the front plate.
Installation
70 160 200
plate 4
58
Slots
Installation plate 4
Water Inlet
Screws 5 Water Outlet
CAUTION
Do not over tighten, over tightening cause water leakage.
59
Packing 3
Drain Elbow 2
60
connecting
terminal board
For model S*C09*3E8
5mm or
Power Supply Isolating Recommended more
Cable Size No loose strand (gap between
Cord Devices RCD
when insert wires)
5 × minimum
1 2 20A 30mA, 4P, type A Conductor Conductor Conductor not
1.5 mm
3 × minimum fully insert over insert fully insert
2 2 15/16A 30mA, 2P, type AC
1.5 mm
61
Disconnect the
Remote controller
wiring
62
Claw (2 places)
Existing Remote
Wall to which
the remote
controller cover
controller is
Hook (6 places)
fixed
Hole for
screw
Screw Claw (2 places)
(field supply)
Air purge valve 9
Remote controller
Connect the remote
terminal board
control wiring
Top case Remove the coating.
Approx. 6 mm
Bottom case (Back side)
(Back side)
63
WARNING
Be careful not to touch parts other than RCCB/ELCB test button
when the power is supplied to Indoor Unit. Else, electrical shock
may happen. Before obtaining access to terminals, all supply
circuits must be disconnected.
64
11.1.10.1 Maintenance for Water Filter Is water pressure higher than 0.05 MPa?
65
Outdoor Indoor
Installer setting
System setup
Optional PCB connectivity - No
2. Room Thermostat
Indoor unit receive Room Thermo signal (ON/OFF) from Remote controller
to control HP and circulation pump.
Outdoor Indoor There is a build-in thermistor in the remote controller.
Installer setting
System setup
Optional PCB connectivity - No
Outdoor Indoor
Room
Thermostat
(Field supply)
Setting of remote controller
Installer setting
System setup
Optional PCB connectivity - No
66
Max : 30m
Thermistor Setting of remote controller
Installer setting
System setup
Optional PCB connectivity - No
Buffer tank
Floor heating 1 Floor heating 2
Connect floor heating to 2 circuits through buffer tank as shown in the figure.
Install mixing valves, pumps and thermistors (specified by Panasonic) on both circuits.
Remove remote controller from indoor unit, install it in one of the circuit and use it as Room Thermostat.
Install external Room Thermostat (field supply) in another circuit.
Both circuits can set circulation water temperature independently.
Install buffer tank thermistor on buffer tank.
It requires connection setting of buffer tank and ∆T temperature setting at heating operation separately.
This system requires optional PCB (CZ-NS4P).
67
Outdoor Indoor
Radiator
Pump 2 Setting of remote controller
Thermistor 2
Installer setting
System setup
Mixing valve 1 Pump 1 Optional PCB connectivity - Yes
Zone 2 :Sensor
Floor heating Room
Buffer tank Water temperature
Connect floor heating or radiator to 2 circuits through buffer tank as shown in figure.
Install pumps and thermistors (specified by Panasonic) on both circuits.
Install mixing valve in the circuit with lower temperature among the 2 circuits.
(Generally, if install floor heating and radiator circuit at 2 zones, install mixing valve in floor heating circuit.)
Remote controller is installed on indoor unit.
For temperature setting, select circulation water temperature for both circuits.
Both circuits can set circulation water temperature independently.
Install buffer tank thermistor on buffer tank.
It requires connection setting of buffer tank and ∆T temperature setting at heating operation separately.
This system requires the optional PCB (CZ-NS4P).
Mind that if there is no mixing valve at the secondary side, the circulation water temperature may get higher than
setting temperature.
Zone 2
Swimming pool
Thermistor 1
T
Heat EXT
Buffer tank
Floor heating 1 Swimming pool
Connect floor heating and swimming pool to 2 circuits through buffer tank as shown in figure.
Install mixing valves, pumps and thermistors (specified by Panasonic) on both circuits.
Then, install additional pool heat exchanger, pool pump and pool sensor on pool circuit.
Remove remote controller from indoor unit and install in room where floor heating is installed. Circulation water
temperature of floor heating and swimming pool can be set independently.
Install buffer tank sensor on buffer tank.
It requires connection setting of buffer tank and ∆T temperature setting at heating operation separately. This system
requires the optional PCB (CZ-NS4P).
68
Installer setting
System setup
Optional PCB connectivity - Yes
T
Heat EXT
Swimming pool
In this application, cooling mode cannot be selected. (not display on remote controller)
Zone 2 :Sensor
Room
Thermistor 2 Water temperature
Operation setup
Heat
T for heating ON – 1°C
Cool
T for cooling ON – 1°C
(CAUTION)
Thermistor 1 does not affect operation directly. But error happens if it is not installed.
Please adjust flow rate of zone 1 and zone 2 to be in balance. If it is not adjusted correctly, it may affects the
performance.
(If zone 2 pump flow rate is too high, there is possibility that no hot water flowing to zone 1.)
Flow rate can be confirmed by “Actuator Check” from maintenance menu.
69
Outdoor Indoor
Tank thermistor
Booster heater
This is an application that connects the DHW tank to the indoor unit through 3-way valve.
DHW tank’s temperature is detected by tank thermistor (specified by Panasonic).
Outdoor Indoor
This is an application that connects the DHW tank to the indoor unit through 3-way valve before connect the solar
water heater to heat up the tank. DHW tank’s temperature is detected by tank thermistor (specified by Panasonic).
Solar panel’s temperature is detected by solar thermistor (specified by Panasonic).
DHW tank shall use tank with built-in solar heat exchange coil independently.
Heat accumulation operates automatically by comparing the temperature of tank thermistor and solar thermistor.
During winter season, solar pump for circuit protection will be activated continuously. If does not want to activate the
solar pump operation, please use glycol and set the anti-freezing operation start temperature to -20°C.
This system requires optional PCB (CZ-NS4P).
Floor heating
This is an application that connects the buffer tank to the indoor unit.
Buffer tank’s temperature is detected by buffer tank thermistor (specified by Panasonic).
This system requires optional PCB (CZ-NS4P).
70
This is an application that connects the buffer tank to the indoor unit before connecting to the solar water heater to
heat up the tank.
Buffer tank’s temperature is detected by buffer tank thermistor (specified by Panasonic).
Solar panel’s temperature is detected by solar thermistor (specified by Panasonic).
Buffer tank shall use tank with built-in solar heat exchange coil independently.
During winter season, solar pump for circuit protection will be activated continuously. If does not want to activate the
solar pump operation, please use glycol and set the anti-freezing operation start temperature to -20°C.
Heat accumulation operates automatically by comparing the temperature of tank thermistor and solar thermistor.
This system requires optional PCB (CZ-NS4P).
Boiler connection
Boiler
This is an application that connects the boiler to the indoor unit, to compensate for insufficient capacity by operate
boiler when outdoor temperature drops & heat pump capacity is insufficient.
Boiler is connected parallel with heat pump against heating circuit.
There are 3 modes selectable by remote controller for boiler connection.
Besides that, an application that connects to the DHW tank’s circuit to heat up tank’s hot water is also possible.
(Operation setting of boiler shall be responsible by installer.)
This system requires optional PCB (CZ-NS4P).
Depending on the settings of the boiler, it is recommended to install buffer tank as temperature of circulating water
may get higher. (It must connect to buffer tank especially when selecting Advanced Parallel setting.)
WARNING
Panasonic is NOT responsible for incorrect or unsafe situation of the boiler system.
CAUTION
Make sure the boiler and its integration in the system complies with applicable legislation.
Make sure the return water temperature from the heating circuit to the indoor unit does NOT exceed 55°C.
Boiler is turned off by safety control when the water temperature of the heating circuit exceed 85°C.
71
Resistance (Ω)
12000
11.2.3.1 Connecting with external 10000
device (optional) 8000
6000
All connections shall follow to the local national
4000
wiring standard. 2000
It is strongly recommended to use manufacturer- 0
recommended parts and accessories for -30 -20 -10 0 10 20 30
installation. ˚C
Tank sensor characteristic
For connection to main PCB 4 .
1. Two-way valve shall be spring and electronic type,
9. Room sensor zone 1 cable shall be (2 × min 0.3
refer to “Field Supply Accessories” table for details.
Valve cable shall be (3 × min 1.5 mm2), of type mm2) double insulation layer of PVC-sheathed or
designation 60245 IEC 57 or heavier, or similarly rubber-sheathed.
10. Outdoor air sensor cable shall be (2 × min 0.3
double insulation sheathed cable.
* note: - Two-way Valve shall be CE marking mm2) double insulation layer of PVC-sheathed or
compliance component. rubber-sheathed.
11. Tank OLP cable must be (2 × min 0.5 mm2),
- Maximum load for the valve is 9.8VA.
2. Three-way valve shall be spring and electronic double insulation layer of PVC-sheathed or
type. Valve cable shall be (3 × min 1.5 mm2), of rubber-sheathed cable.
type designation 60245 IEC 57 or heavier, or
similarly double insulation sheathed cable.
* note: - Shall be CE marking compliance
component. Main PCB 4
- It shall be directed to heating mode when
it is OFF. Power Supply 2
RCCB/ELCB
- Maximum load for the valve is 9.8VA.
3. Room thermostat cable must be (4 or 3 × min 0.5
Power Supply 1
mm2), of type designation 60245 IEC 57 or RCCB/ELCB
Bind optional
cables with
heavier cord, or similarly double insulation these bands
sheathed cable.
4. Maximum output power of booster heater shall be
≤ 3 kW. Booster heater cable must be (3 × min 1.5
mm2), of type designation 60245 IEC 57 or
heavier.
5. Extra pump cable shall be (2 × min 1.5 mm2), of For S*C09*3E8
72
IEC 57 or heavier.
6. Mixing valve zone 1 and zone 2 cable shall be (3 Bind all optional Holder (Clampe
× min 1.5 mm2), of type designation 60245 IEC 57 cables with these For S*C12/16*9E8
bands
or heavier.
How to guide the optional cables and power supply cord
7. Room sensor zone 1 and zone 2 cable shall be (2
(view without internal wiring)
× min 0.3 mm2), double insulation layer (with
insulation strength of minimum 30V) of PVC-
sheathed or rubber-sheathed cable.
8. Buffer tank sensor, pool water sensor and solar
sensor cable shall be (2 × min 0.3 mm2), double
insulation layer (with insulation strength of
minimum 30V) of PVC-sheathed or rubber-
sheathed cable.
9. Water sensor zone 1 and zone 2 cable shall be (2
× min 0.3 mm2), double insulation layer of PVC- Optional cables:
• 3-way valve cable
sheathed or rubber-sheathed cable. • 2-way valve cable
10. Demand signal cable shall be (2 × min 0.3 mm2), • Booster heater cable • Power Supply 1 cord
• Extra pump cable • Power Supply 2 cord
double insulation layer of PVC-sheathed or • Boiler contact cable • Indoor Unit/Outdoor
Unit Connecting cable
rubber-sheathed cable.
Optional cables:
11. SG signal cable shall be (3 × min 0.3 mm2), • Pump zone 1 cable
double insulation layer of PVC-sheathed or • Pump zone 2 cable
• Solar pump cable
rubber-sheathed cable. • Pool pump cable from optional
12. Heat/Cool switch cable shall be (2 × min 0.3 mm2), • Room thermostat zone 1 cable PCB
• Room thermostat zone 2 cable
double insulation layer of PVC-sheathed or • Mixing valve zone 1 cable
• Mixing valve zone 2 cable
rubber-sheathed cable.
Optional cables:
13. External compressor switch cable shall be (2 × • External control cable
min 0.3 mm2), double insulation layer of PVC- • Tank sensor cable
• Outdoor air sensor cable
sheathed or rubber-sheathed cable. • Tank OLP cable
• Remote controller cable
• Room sensor zone 1 cable
• Room sensor zone 2 cable
• Buffer tank sensor cable
• Pool sensor cable
• Water sensor zone 1 cable
• Water sensor zone 2 cable from optional PCB
• Demand signal cable
• Solar sensor cable
• SG signal cable
• Heat/Cool switch cable
• External Compressor switch cable
73
Solar Ext.
Pump comp.
SW
OLP for booster Error
heater Heat/
signal Cool
Zone 1 room sensor SW
Outdoor air sensor Zone 1
Tank sensor Pump Vcc
SG
Bit1
signal
External control Zone 2 Bit2
Remote controller Pump
Boiler contact
Extra pump
Zone 2 Zone 1 Buffer Pool Zone 2 Zone 1 Demand Solar
Booster heater room room Tank water water water signal sensor
sensor sensor sensor sensor sensor sensor
CON CON H C N L
2-way 3-way Optional ■ Signal inputs
valve valve Thermostat 1
74
75
Slot
Connector
WARNING
This section is for authorized and licensed electrician/water system
installer only. Work behind the front plate secured by screws must
only be carried out under supervision of qualified contractor,
installation engineer or service person.
3. On the wall near the Indoor Unit, attach the
11.2.3.6 Network Adaptor 8 Installation adaptor by screwing screws through the holes
(Optional) in the back cover.
1. Open the Control Board Cover 6 , then
connect the cable included with this adaptor to
the CN-CNT connector on the printed circuit
board.
Pull the cable out of the Indoor Unit so that there
is no pinching. Screws
If an optional PCB has been install in the Indoor
Unit, connect the CN-CNT connector to Optional
PCB 7 .
CN-CNT cable
(Take care not to
pinch the cable)
For S*C09*3E8
For S*C12/16*9E8
76
Cord clamp
Cable tie
77
Name Function
A: Main screen Display information
A B: Menu Open/Close main menu
C: Triangle (Move) Select or change item
D: Operate Start/Stop operation
B
E: Back Back to previous item
C F: Quick Menu Open/Close Quick menu
D G: OK Confirm
E F G
10:34am, Mon
24 40˚c
˚c 18˚c 6
2 3 4
Name Function
Heating Cooling
5: Display tank temp Display current tank temperature (it is set temperature when enclosed by line)
78
17:26, Wed
Start
Language 12:00, Wed
ENGLISH
When any button is pressed, language
FRANCAIS setting screen appears.
DEUTSCH (CAUTION) If initial setting is not
performed, it does not go into menu.
ITALIANO
Select Confirm
24h
When language is set, setting screen of
time display appears (24h/am/pm)
am/pm
Select Confirm
Select Confirm
17:26, Wed
Start
Select Confirm
79
3
Heater capacity Capacity select
4
Anti freezing Yes/No
5
Tank connection
Yes/No
6 Only when the selection for optional PCB is Yes
Buffer Tank connection
Yes/No ∆T setup
7 Only when the selection for Tank connection is Yes
Tank heater External/Internal Heater ON time setup
8
Base pan heater Yes/No A/B
9
Alternative outdoor sensor Yes/No
10
Bivalent connection Yes/No Bivalent setup
11
External SW
Yes/No
12 Only when the selection for optional PCB is Yes
Solar connection
Yes/No Tank setup Solar setup
13 Only when the selection for optional PCB is Yes
External Error signal
Yes/No
14 Only when the selection for optional PCB is Yes
Demand control
Yes/No
15 Only when the selection for optional PCB is Yes
SG ready
Yes/No Capacity setup
16 Only when the selection for optional PCB is Yes
External Compressor SW Yes/No
17
Circulation liquid
Water/glycol
18 Only when the selection for optional PCB is Yes
Heat-Cool SW Yes/No
19
Force Heater Auto/Manual
80
22
∆T for heating ON ∆T for heating setup
23
Outdoor temp. for heater ON O/D temp for heater ON setup
27
Outdoor temp. for
Cool Heat change temp. setup
Only when the (Cool to Heat)
selection for Tank
is Yes 28
Tank Floor operation time (max.) Max. operation time for Heat & Cool mode setup
29
Tank heat up time (max.) Max. operation time for Tank mode setup
30
Tank re-heat temp. Tank re-heat temp. setup
31
Sterilization Sterilization day and temp. and time setup
32
Service setup Pump maximum speed Pump maximum speed setup Air purge
33
Pump down Pump down ON / OFF
34
Dry concrete ON (Dry concrete)
81
2. Zone & Sensor Initial setting: Room and Water temp. System setup 17:26, Wed
Optional PCB connectivity
If no Optional PCB connectivity
Zone & Sensor
Select sensor of room temperature control from the following 3 items
Water temperature (circulation water temperature) Heater capacity
Room thermostat (Internal or External) Anti freezing
Room thermistor
Select Confirm
When there is Optional PCB connectivity
Select either 1 zone control or 2 zone control.
If it is 1 zone, select either room or pool, select sensor
If it is 2 zone, after select sensor of zone 1, select either room or pool for zone
2, select sensor
(CAUTION) In 2 zone system, pool function can be set at zone 2 only.
3. Heater capacity Initial setting: Depend on model System setup 17:26, Wed
Optional PCB connectivity
If there is built-in Heater, set the selectable heater capacity. Zone & Sensor
(CAUTION) There are models which cannot select heater. Heater capacity
Anti freezing
Select Confirm
(CAUTION) If set No, when the water temperature is reaching its freezing Select Confirm
temperature or below 0°C, the water circulation circuit may freeze and
cause malfunction.
82
Please set “Tank heater” to “ON” in the “Function setup” from remote controller Select Confirm
when using heater to boil the tank.
External A setting which is using booster heater installed on Internal A setting which is using backup heater of indoor unit to
DHW tank to boil the tank. boil the tank.
The permissible heater capacity is 3kW and below. The operation to boil the tank with heater is as below.
The operation to boil the tank with heater is as below.
In addition, be sure to set suitable “Tank heater: ON
time”
HP thermo OFF
HP thermo OFF
HP
HP
Booster heater
Booster heater
Pump
Pump
83
When the boiler operation is “ON”, “boiler contact” is “ON”, “_”(underscore) will be displayed below the boiler icon.
Please set target temperature of boiler to be the same as heat pump temperature.
When boiler temperature is higher than heat pump temperature, zone temperature cannot be achieved if mixing valve is not installed.
This product only allows one signal to control the boiler operation. Operation setting of boiler shall be responsible by installer.
84
If follow Swiss standard power connection, need to turn on DIP SW of main unit Select Confirm
PCB. ON/OFF signal used to ON/OFF tank heater (for sterilization purpose)
85
19. Force Heater Initial setting: Manual System setup 17:26, Wed
External compressor SW
Under manual mode, user can turn on force heater through quick menu. Circulation liquid
If selection is 'auto', force heater mode will turn automatically if pop up error Heat-Cool SW
happen during operation. Force heater
Force heater will operate follow the latest mode selection, mode selection is
dsiable under force heater operation. Select Confirm
20. Water temp. for heating ON Initial setting: compensation curve 55°C
Decide temperature
of 4 points as shown
Set target water temperature to operate heating operation. Hot water temperature in diagram
Compensation curve: Target water temperature change in conjunction with
outdoor ambient temperature change.
Direct: Set direct circulation water temperature. 35°C
In 2 zone system, zone 1 and zone 2 water temperature can be set separately. Outdoor
-5°C 15°C temperature
compensation curve
24°C
Set temp difference between out temp & return temp of circulating water of
Heating operation.
When temp gap is enlarged, it is energy saving but less comfort. When the Return
gap gets smaller, energy saving effect gets worse but it is more comfortable.
Setting range is 1°C ~ 15°C Out — Return = 1°C ~ 15°C
ON
23. Outdoor temp. for heater ON Initial setting: 0°C
86
24. Water temp. for cooling ON Initial setting: compensation curve 20°C
In 2 zone system, zone 1 and zone 2 water temperature can be set separately. 20°C 30°C
compensation curve
Set temp difference between out temp & return temp of circulating water of
Cooling operation.
When temp gap is enlarged, it is energy saving but less comfort. When the Return
gap gets smaller, energy saving effect gets worse but it is more comfortable.
Return — Out = 1°C ~ 15°C
Setting range is 1°C ~ 15°C
Auto
26. Outdoor temp. for (Heat to Cool) Initial setting: 15°C Heat Outdoor temp. rising
Set outdoor temp that switches from heating to cooling by Auto setting.
Setting range is 5°C ~ 25°C
Cool
Timing of judgement is every 1 hour
15°C
27. Outdoor temp. for (Cool to Heat) Initial setting: 10°C Heat Outdoor temp. dropping
Set outdoor temp that switches from Cooling to Heating by Auto setting.
Setting range is 5°C ~ 25°C
Cool
Timing of judgement is every 1 hour
10°C
Tank
5min ~ 4h
87
Select
33. Pump down Service setup 17:26, Wed Service setup 17:26, Wed
Pump down operation
Pump down: Pump down: in progress!
Operate pump down operation
ON ON
OFF
Confirm Confirm
45°C
34. Dry concrete
40°C 40°C
Operate concrete curing operation. 35°C 35°C
Select Edit, set temp for every stage (1~99 1 is for 1 day). 30°C
Setting range is 25~55°C
35. Service contact Service setup 17:26, Wed Contact-1: Bryan Adams
Service contact: ABC/ abc 0-9/ Other
Able to set name & tel no. of contact
Contact 1 ABCDEFGHIJKLMNOPQR
person when there is breakdown
etc. or client has trouble. (2 items) Contact 2 STUVWXYZ abcdefghi
jklmnopqrstuvwxyz
Select Confirm Select Enter
88
89
If piping length is over 10 m, additional refrigerant should be added as shown in the table.
Example:
If piping length is 30 m, the quantity of additional refrigerant should be 1000g. [(30-10)m × 50 g/m = 1000g]
GWP (R410A) = 2088
90
or 0mm
10 Saddle
re
or 0mm
mo
mo
10
re
Indoor/Outdoor connecting cable
- For UX09*E5*, UX12*E5*, UD12*E5*, UD16*E5* use 4-CORE WIRE
min 4.0mm 2 or 6.0mm 2
- For UX09*E8*, UX12*E8*, UX16*E8*, UD0 9*E8*, UD12*E8*,
UD16*E8* use 6-CORE WIRE min 1.5mm 2
Type designation 60245 IEC 57 or heavier cord
m
m e
00 or ø9.52mm (3/8") Liquid refrigerant piping
10 r m
o
ø15.88mm (5/8") Gas refrigerant piping
30
or 0mm
mo
re
[ Check that the cables do not
touch the compressor, etc. ]
E Model A B C D E F
UX09*E5*,UX12*E5*,
C
F
UD12*E5*,UD16*E5*,
(Anchor pitch)
UD12*E8*,UD16*E8*
A B (Unit : mm)
(Anchor pitch)
After selecting the best location, start installation according to Installation Diagram.
1. Fix the unit on concrete or rigid frame firmly and horizontally by bolt nut (ø10 mm).
2. When installing at roof, please consider strong wind and earthquake. Please fasten the installation stand firmly
with bolt or nails.
Drain elbow 1
Rubber cap 2 x8
91
92
Liquid side
Indoor unit
Two-way valve Outdoor unit
Close
Gas side
Vacuum CLOSE
pump OPEN
1 Connect a charging hose with a push pin to the Low side of a charging set and the service port of the 3-way
valve.
Be sure to connect the end of the charging hose with the push pin to the service port.
2 Connect the center hose of the charging set to a vacuum pump with check valve, or vacuum pump and
vacuum pump adaptor.
3 Turn on the power switch of the vacuum pump and make sure that the needle in the gauge moves from
0 cmHg (0 MPa) to –76 cmHg (–0.1 MPa). Then evacuate the air approximately ten minutes.
4 Close the Low side valve of the charging set and turn off the vacuum pump. Make sure that the needle in the
gauge does not move after approximately five minutes.
Note: BE SURE TO FOLLOW THIS PROCEDURE IN ORDER TO AVOID REFRIGERANT GAS LEAKAGE.
5 Disconnect the charging hose from the vacuum pump and from the service port of the 3-way valve.
6 Tighten the service port caps of the 3-way valve at a torque of 18 N•m with a torque wrench.
7 Remove the valve caps of both of the 2-way valve and 3-way valve. Position both of the valves to “OPEN”
using a hexagonal wrench (4 mm).
8 Mount valve caps onto the 2-way valve and the 3-way valve.
Be sure to check for gas leakage.
CAUTION
If gauge needle does not move from 0 cmHg (0 MPa) to –76 cmHg (–0.1 MPa), in step 3 above take the following measure:
If the leak stops when the piping connections are tightened further, continue working from step 3 .
If the leak does not stop when the connections are retightened, repair the location of leak.
Do not release refrigerant during piping work for installation and reinstallation. Take care of the liquid refrigerant, it may cause
frostbite.
93
7
3
2
4 8
N2 R-###
2
An example illustrations of setup for
refrigerant leak detection.
Step 2: Refrigerant leak detection through Electronic halogen leak detector and/or ultrasonic leak detector:
1. Use any one of below detector to check leaking.
Electronic halogen leak detector.
Switch on the unit.
Cover the test area from direct draft.
Pass the detection probe near test area and wait for audible and visible signals.
Ultrasonic Leak Detector
Make sure the area is quiet.
Switch on the ultrasonic leak detector.
Move the probe along your air conditioning system to test for leaks, and mark for repair.
2. Any leak detected at this level shall be repaired and retested, starting from “Step 1: Pressure test”.
NOTE:
Always recover the refrigerant and Nitrogen gas into recovery cylinder after completion of a test.
You must use the detection equipment with Detectable Leak Rate of 10-6 Pa.m3/s or better.
Do not use refrigerant as test medium for system with total refrigerant charge more than 5kg.
Test shall be performed with dry Nitrogen or another non-flammable, non-reactive, dried gas. Oxygen, air or
mixtures containing them shall not be used.
Next, remove the moisture, or repair, and redo the refrigerant leak testing, starting from “Step 1: Pressure test”.
(Low/Gas)
pressure gauge (High/Liquid) pressure gauge
Handle 2
Vacuum pump 2
94
WARNING
This equipment must be properly earthed.
Earth Wire
must be
longer than
others cables Earth Wire
for safety must be
reason. longer than
others cables
for safety
reason.
CAUTION
For three phase model never operate the unit by pressing the
electromagnetic switch.
Never correct the phase by switching over any of the wires
inside the unit.
• Select required direction and apply protective bushing provided in accessories to protect cables from sharp edges.
• Once all wiring work has been completed, tie the cable and cord together with the binding strap so that they do not touch other parts such as the
compressor and bare copper pipes.
Outdoor Unit
Indoor/outdoor unit
terminal board Protective
bushing 3 Selection
of direction
Cord clamp
Banding strap
(Field Supply) Apply cut
95
Wire stripping
Indoor/outdoor Conductor fully Conductor over Conductor not
insert insert fully insert
10 ± 1 mm
connecting terminal
board
5 mm or more
(gap between wires)
No loose strand when insert ACCEPT PROHIBITED PROHIBITED
96
97
12.1.4.1 Target Water Temperature Control of Standard System (Optional PCB not
connected)
There are 2 types of temperature control selection which are Compensation and Direct.
Temperature control type selection by installer:
1) Compensation : Wlo, WHi, ODLo, ODHi can be set at installer menu.
2) Direct : Direct Water Temperature Set
Remote control setting by user:
1) Compensation : Shift value ±5°C from the compensation curve
2) Direct : Direct water temperature set change
*This setting at is only able to set when the room sensor select as Water Temperature.
*Instead of water temperature, user will set target room temperature when room sensor select as Room Thermistor
or Internal Room Thermostat.
Compensation Direct
A (Base Temperature)
Value from the curve + User shift value set Direct value from user setting
- B (shift temperature) value is depend on the room sensor selection at remote controller as below table:
B (Shift Temp.) B shift value is depend on the room sensor selection at remocon as table below
Sensor Selection
Water temperature B=0
External Room Thermostat B=0
Cool Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
Internal Room Thermostat B = 1 * (room set temp. (R/C) – actual room temp.)
& Max/Min Regulation of B: (Max: 5°C ; Min: -5°C)
Room Thermistor
Heat Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
B = follow Heating PI control contents
98
Heating Cooling
Max 55°C 20°C
Min 20°C 5°C
W (LO)
W (HI)
However, when powerful mode is requested by remote control during heating mode, the higher value of HLo or Whi
will be used for A calculation.
*There are 2 compensation curves (for heating and cooling). During heating mode, the heating curve is used and
during cooling mode, the cooling curve is use.
Tw
Tw_Hi
+5
Tw_Lo ±5 Shift value
-5
To_Lo To_Hi To
99
Cool mode:
- Target water temperature setting:
Max = 20°C Min= 5°C
100
Cancel condition
- Heating zone 1 is OFF by remote control or Timer or Auto mode AND
- Cooling zone 1 is OFF by remote control or Timer or Auto mode.
Compensation Direct
A (Base Temperature)
Value from the curve + User shift value set Direct value from user setting
* During heat mode and compensation select, if powerful mode is activated, higher value of WLo or WHi will be use
as curve value.
- B (shift temperature) value is depend on the room sensor selection at remote controller as below table:
B (Shift Temp.) B shift value is depend on the room sensor selection at remocon as table below
Sensor Selection
Water temperature B=0
External Room Thermostat B=0
Cool Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
Internal Room Thermostat B = 1 * (room set temp. (R/C) – actual room temp.)
& Max/Min Regulation of B: (Max: 5°C ; Min: -5°C)
Room Thermistor Heat Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
B = follow Heating PI control contents
Pool Function Selected B = Delta value setting from remocon
*B = 0 regardless of which sensor selection, if SHP control bit is enable except Pool function select (maintain Pool “B”
value)
** Pool function also can be select at Zone 1 when optional PCB is connected and Zone 1 system is select.
Maximum/minimum regulation of Target Water Temperature.
Heating Cooling
Max 55°C 20°C
Min 20°C 5°C
Target Zone 1 Water Temperature (Heat mode only) during SG ready control
- If buffer tank selection is “NO” then following shift is carried out.
o While digital input is “10” or “11” then,
Final Target Zone 1 water temperature
= Target Zone 1 water temperature* (SG ready % setting (remote control menu))%
- If buffer tank selection is “YES”
o No shift of Target Zone 1 Water Temperature. Target Buffer Tank Temperature will change accordingly.
* Refer to “Buffer tank temperature control”
101
Cancel condition
- Heating zone 2 is OFF by remote control or Timer or Auto mode AND
- Cooling zone 2 is OFF by remote control or Timer or Auto mode.
Compensation Direct
A (Base Temperature)
Value from the curve + User shift value set Direct value from user setting
* During heat mode and compensation select, if powerful mode is activated, higher value of WLo or WHi will be use
as curve value.
- B (shift temperature) value is depend on the room sensor selection at remote controller as below table:
B (Shift Temp.) B shift value is depend on the room sensor selection at remocon as table below
Sensor Selection
Water temperature B=0
External Room Thermostat B=0
Cool Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
Internal Room Thermostat B = 1 * (room set temp. (R/C) – actual room temp.)
& Max/Min Regulation of B: (Max: 5°C ; Min: -5°C)
Room Thermistor Heat Mode:
B = 0 ; when Zone OFF or Zone Room Thermo OFF
B = follow Heating PI control contents
Pool Function Selected B = Delta value setting from remocon
*B = 0 regardless of which sensor selection, if SHP control bit is enable except Pool function select (maintain Pool “B”
value)
** Pool function also can be select at Zone 2 when optional PCB is connected and Zone 2 system is select.
Maximum/minimum regulation of Target Water Temperature.
Heating Cooling
Max 55°C 20°C
Min 20°C 5°C
Target Zone 2 Water Temperature (Heat mode only) during SG ready control
- If buffer tank selection is “NO” then following shift is carried out.
o While digital input is “10” or “11” then,
Final Target Zone 2 water temperature
= Target Zone 1 water temperature* (SG ready % setting (remote control menu))%
- If buffer tank selection is “YES”
o No shift of Target Zone 2 Water Temperature. Target Buffer Tank Temperature will change accordingly.
* Refer to “Buffer tank temperature control”
102
* There will be no zone sensor connected to zone 1 (No zone sensor error), mixing valve and zone pump will not
operate.
* There will be no zone sensor connected to zone 1 (No zone sensor error), mixing valve and zone pump will not
operate.
103
COOL
MODE
Heat To Cool
Setting Temp. Cool To Heat
Setting Temp.
HEAT
MODE
Outdoor Ambient
Control details:
o To enable the unit to operate either heat or cool mode automatically, heat to cool set temperature and
cool to heat set temperature can be set by control panel.
o Automatic operation is judged based on control panel setting temperature and outdoor ambient
temperature.
* Minimum setting of heat to cool set temperature is 1°C higher than cool to heat set temperature.
Judgement control:
o If outdoor ambient temperature < Heat to Cool Set Temperature, unit will operate in Heat Mode or else
the unit will operate in Cool Mode.
o If current operation is Cool mode, outdoor ambient temperature > Cool to Heat Temperature, unit will
maintain Cool mode operation or else the unit will operate Heat mode.
o If current operation is Heat mode, outdoor ambient temperature > Heat to Cool Temperature, unit will
maintain Heat mode operation or else the unit will operate Cool mode.
o Every 60 minutes the outdoor ambient temperature is judged.
o When Auto + Tank mode is selected, operation mode switching is judged by both outdoor ambient
temperature and indoor air temperature.
104
Compressor
ON
19°C
16°C
Compressor
OFF
Outdoor Ambient
Temperature
Auto Mode Cooling Only operation will start once the outdoor ambient temperature reaches 19°C and
compressor will continue to run until the outdoor ambient temperature drops to 16°C.
Due to this limitation,
If Heat to Cool temperature is set lower than 19°C, the compressor will not operates until the outdoor
ambient temperature reaches 19°C or higher.
o Tank Thermo ON
* When tank thermo ON, water pump will ON for 3 minutes then only heat pump turn ON.
* Tank water set temperature = tank set temperature or 51°C whichever lower.
105
1) When tank temperature achieve heat pump OFF condition, refer below condition:
Condition 1: When Internal Tank Heater is select and Tank Heater ON
- Heat pump will turn OFF, water pump continue ON and room heater will continue ON if tank temperature
below tank heater thermo ON condition. 3 ways valve will only switch to room side after tank temperature
reach tank heater thermo OFF condition.
Condition 2: When Tank Heater select OFF OR when External Tank Heater is select and Tank heater ON
- If tank temperature achieve tank thermo OFF, heat pump turn OFF, water pump turn OFF, room heater OFF
and 3 ways valve switch to room side.
2) When tank temperature achieve heat pump ON condition, water pump ON, heat pump ON and room heater turn
OFF.
a) Tank temperature > tank water set temperature continuously for 20 seconds after heat pump thermos OFF
due to water thermo. (Heat pump turn OFF but water pump continue ON and room heater turn ON to achieve
tank set temperature) OR
b) Tank temperature > tank set temperature + [1°C] for continuously 20 seconds. (Heat pump OFF, water pump
OFF, room heater OFF and 3 ways valve switch to room side)
a) Tank temperature < tank water set temperature + R/C setting (Tank re-heat temp)
(Water pump turn ON OR continue ON, heat pump ON and 3 ways valve switch to tank side or maintain at
tank side)
106
107
108
Others <Tank water set temperature + R/C setting (Tank re-heat temperature)
109
ON Fan Speed ON
Outdoor Fan:
30 sec
OFF
110
Pump ON Request
YES
ON Water Pump
NO
Pump ON Time
≥ 70 Sec?
YES
NO
Water Flowrate Abnormal
> 15 Sec?
YES
111
However, the following sequences do not follow maximum pump duty setting by remote control.
- Pump down mode
- Air purge mode
- Normal deice
(P - Q)
150
140
130
120
110
100
Pressure, P (kpa)
90
80
70
60
Max Duty C5
50
40
30
12kW Rated Duty 8B
20
Min Duty 50 9kW Rated Duty 7A
10
0
0 10 20 30 40 50 60
Water Flow Rate, Q (L/min)
WH-SDC16H9E8
(P - Q)
150
140
130
120
110
100
Pressure, P (kpa)
90
80
70
60
50 Max Duty C5
40
30 Rated Duty 9C
20 Min Duty 50
10
0
0 10 20 30 40 50 60
Water Flow Rate, Q (L/min)
112
Content:
- AC type water pump install for this zone water pump control. When optional PCB connected, 230V output will
drive this zone pump.
- There are three pump can be connected through Optional PCB. (Zone 1 Pump, Zone 2 Pump, & Pool Pump)
* Zone 1 pump [P1] use to circulate zone 1 water circuit & Zone 1 mixing valve [M1] adjust to control the
Zone 1 target water temperature.
* Zone 2 pump [P2] use to circulate zone 2 water circuit & Zone 2 mixing valve [M2] adjust to control the
Zone 2 target water temperature.
* When Pool Function select as Zone 2 circuit, [P2] use to circulate water to heat exchanger which use to
transfer heat to pool water.
* Pool pump [P3] circulates the pool water through the heat exchanger to get warm water.
* Zone 1 & Zone 2 water pump need to turn OFF when antifreeze deice pump stop control activate and turn
ON back after the antifreeze deice pump stop control end under setting of "NO" buffer tank connection.
113
114
Pump ON
10s
Flow SW ON?
YES
NO to normal mode
Water In > 80°C for 10s
YES
Pump OFF
>10 mins
YES
115
116
Control content:
- This Heater protection control will activate only if the backup heater is enable at custom setup by remote
controller. Once fulfil the start condition, room heater will turn ON together (base on max heater capacity
selection) and stop together if stop condition is fulfilled.
* If the heater is request to turn ON OLP feedback will be detected.
Starting conditions:
1. During normal deice operation 4~9
2. Water outlet temperature < 10°C or
Outdoor air temperature < -10°C or
Water inlet temperature < 27°C
Stop condition:
1. When normal deice end or
2. Water outlet temperature > 45°C
117
The remote control Tank set Temperature range will change according to the External and Internal Tank Heater use.
Heater OFF
Heater ON
* TANK HEATER DELAY TIMER is clear when tank heat-up interval end.
118
* Backup Heater Turn ON/OFF all together according to the selected heater capacity.
Tank Temp.
65°C
Backup
Heater
Operation
Heat Pump
Operation
Time
119
Control contents:
o Base pan heater is ON during deice operation and continues ON for 10 minutes after deice operation
ends.
Cancel condition:
o When outdoor temperature > 6°C after deice end or
o When operation is not at heating mode or
o Base pan heater ON timer count is completed.
Cancel conditions:
o When outdoor air temperature is > 7°C or
o When operation is not at heating mode.
Start condition:
- Tank heater function select YES by remote controller
Control contents:
a) When there is only one heater source (Room Heater or Tank Heater) request to turn ON, operate same as
normal room heater and tank heater operation.
b) When both backup heater and booster heater request to turn ON at same time, will turn ON only ONE heater
source. Under normal condition, tank heater has priority to turn ON except below condition.
i. Backup Heater Priority to Turn ON when
- Request Backup heater turn ON at Hex Protection control during deice.
- Request Backup Heater turn ON at Hex Protection Control during low water temperature.
- Request Backup Heater turn ON at Anti-frost control.
- Heat pump error and Force Mode operate.
c) When switching from booster heater to backup heater OR backup heater to booster heater, need to delay 5
seconds in between Turn OFF one heater source and Turn ON another heater source.
120
Control contents:
1) After fulfil start condition, indoor will operate the force heater operation according to below mode condition
Heat mode Only : Turn ON backup heater to achieve room heat pump target water temperature.
Heat + Tank mode : Turn ON backup heater to heat up room OR Turn ON Heater to Boil up tank water.
Cool mode Only : Water pump and backup heater will OFF in force heater mode
Cool + Tank mode : Operate pump and internal Heater OR External heater to Boil up tank water.
Tank mode Only : Operate pump and internal Heater OR External heater to Boil up tank water.
* For heat mode condition, backup heater will only turn ON if the backup heater is enable regardless of Room
Heater Selection
* For tank mode condition, If internal heater selected backup heater will turn ON to boil up tank water.
If external heater selected, booster heater will turn ON to boil up tank water regardless of tank heater
selection
121
Control contents:
During the time set by remote control, powerful will activate according to 2 shift up controls. However, this function is
applicable only for heating. Remote control will transmit the signal to indoor unit once this function is select then
transmit OFF signal to indoor when the timer is complete. Indoor will transmit signal to outdoor for frequency control.
* If “Direct Type” temperature control is select, this powerful shift up setting is not effective.
Start condition
- Powerful function is select by remote control.
End Condition
- OFF/ON button is pressed.
- Powerful function is OFF by remote control.
122
Quiet level
There are 3 level (Level 1, Level 2, Level 3) to set by quick menu function on remote control.
Control content
Once the quiet function is select, the remote control will transmit the signal to indoor and outdoor unit.
Start condition
- Quiet mode is set on remote control.
- Quiet mode is request ON by weekly timer.
Stop condition
If any of below condition is achieve.
- OFF/ON button is pressed.
- Quiet mode is OFF by remote control.
- Quiet mode is request OFF by weekly timer.
Start condition
- Tank connection set to “YES” by remote control
- Sterilization function selects “YES”.
- Sterilization signal received from remote controller by timer.
- Tank mode request ON.
Stop condition
- When boiling timer is completed. Boiling timer (Remote control set maximum operation time) start counting
once tank achieve boiling set temperature OR
- After 8 hours of operation since sterilization start.
- Tank mode request OFF.
Control content:
- During sterilization function activation time, target tank set temperature will internally change to boiling set
temperature.
- During sterilization activates, heat pump and heater (external or internal) will operate as normal tank mode to
achieve the boiling set temperature.
- Sterilization operation will end when stop condition is fulfill.
- After sterilization is complete, tank set temperature will resume to normal operation.
* Tank temperature may not achieve boiling set temperature if tank heater is select OFF OR external compressor
switch.
123
OFF
ON
Control content
- Heating outdoor ambient thermos OFF control only applicable when heat pump operate in heat mode. (This
control will not activate when running in tank side)
- Heat pump and water pump will turn OFF when outdoor ambient is higher than outdoor thermo OFF set
temperature.
- Heat pump thermos ON when outdoor ambient < outdoor thermos OFF set temperature + 1°C.
124
Control Detail:
- Remocon can select either the extra outdoor ambient sensor is connected or not. (YES/NO)
- The alternative outdoor ambient sensor will connect to indoor unit main PCB terminal.
Remocon setting:
Force DHW function can be activate under quick menu.
Control Content:
a) when press the Force DHW function during operation OFF condition:
- When receive this Force DHW bit from remocon, indoor will run tank only mode regardless of the mode
selection.
- After tank temperature achieve tank thermo off temperature, turn OFF force DHW bit and return to operation
OFF with previous mode selection.
* when operation OFF or mode change request from remocon during force DHW mode operation, End force
DHW mode and follow the new request operation.
* Once receive force DHW mode from remocon, indoor direct start tank mode and consider tank thermo ON.
Thermo OFF only when achieve tank thermo OFF depend on the Tank System Setting.
125
Start condition:
a) After [5] min from previous Zone pump off. AND
b) Outdoor air temp < [3] °C OR Outdoor sensor is abnormal. AND
c) Zone water temperature < [6]°C OR Zone Sensor Short or Open
Cancel condition:
a) After water Zone pump ON [4] min AND
b) Outdoor air temp ≥ [4]°C OR
c) During -5 °C ≤ Outdoor air temp < [4] °C OR
Zone water temperature sensor > [8] °C
d) During Outdoor air temp < [-5] °C
Zone water temperature sensor > [20] °C
*However, Zone water temperature sensor is Open or Short, Condition C and D is ignored.
126
a) Solar function can only enable when the Optional PCB is connected.
b) Few part as below need to install to control the solar operation:
- Solar Panel
- Solar Pump
- Solar Panel Sensor
- Tank Sensor (Buffer tank sensor OR DHW Tank sensor depend on the connection direction)
* During Solar Connection to the system, installer need to alert on the high water temperature may flow to the
zone circuit or DHW piping circuit. Therefore pipe which withstand higher water temperature need to be
installed.
127
* Condition c) ignore if the solar system is connect to DHW tank (control active under operation OFF
time for Tank connection case)
- Solar pump stop condition:
a) Solar panel temperature < Delta T turn OFF setting temp (R/C) + Tank temperature (depend on
selection, DHW or Buffer) OR
b) Tank hot water temp >= Solar HI Limit Temp (R/C) + [2]°C
**However, During Cool mode this function cannot activate if Tank selection is “Buffer Tank".
**Solar pump can operate even if Heat pump is under error stop.
128
a) Alternative Mode
- Only one heat source operates at one time, either heat pump or boiler depends on condition.
Control detail:
During Operation ON at Heat mode or Tank mode or Heat + Tank Mode
- Boiler signal turn ON and heat pump and water pump turn OFF when:
a. Outdoor ambient < Outdoor Ambient Set AND
b. Boiler prohibit flag = 0
** However indoor water pump can operate when Anti-freeze control condition fulfilled.
- Boiler signal turn OFF and heat pump and water pump turn ON when:
a. Outdoor ambient > Outdoor Ambient Set + [2°C] OR
b. Boiler prohibit flag = 1
b) Parallel Mode
- Parallel mode allows heat pump and boiler ON at the same time. Boiler operates as an additional heating
capacity when low heat pump capacity at low ambient condition.
Control detail:
During operation ON at Heat mode or Tank mode or Heat + Tank mode
- Boiler signal turns ON when:
a. Outdoor ambient < Outdoor Ambient Set AND
b. Boiler prohibit flag = 0
- Boiler signal turns OFF when:
a. Outdoor ambient > Outdoor Ambient Set + [2°C] OR
b. Boiler prohibit flag = 1
129
Start condition:
a. Water outlet ≥ 85°C continues for 5 minutes.
b. Water inlet ≥ 85°C continues for 5 minutes.
c. Zone1 water temp ≥ 75°C continues for 5 minutes.
d. Zone2 water temp ≥ 75°C continues for 5 minutes.
Contents:
After start condition fulfilled, set boiler prohibit flag = 1
Cancel condition:
- After 30 minutes from start condition fulfilled.
Contents:
Set boiler prohibit flag = 0
130
Maker Characteristic
Siemen (REV200) Touch panel
Siemen (RAA20) Analog
Indoor Unit
9 L (label)
10 Siemen REV200
Cooling 11 L1 (label)
Heating 12 L2 (label)
9 : Terminal Bord No.
Connect only heating line for heating only model. And connect both
heating and cooling line for heat + cool model.
Indoor Unit
9 L (label)
10 Siemen RAA20
Cooling 11 Y1 (label)
Heating 12 Y2 (label)
9 : Terminal Bord No.
Connect only heating line for heating only model. And connect both
heating and cooling line for heat + cool model.
Control Content:
External room thermostat control activate only when remote thermostat connection select YES by Indoor
control panel.
When indoor running heat mode, refer thermo On/Off from heating line feedback. And when indoor running
cool mode, refer thermo On/Off from cooling line feedback.
Heat pump Off immediately when receive thermo off feedback.
131
Control contents:
1 3 ways valve switch Off:
o During 3 ways valve switch Off time, the hot water will provide heat capacity to heating side.
2 3 ways valve switch On:
o During 3 ways valve switch On time, the hot water will provide heat capacity to tank side.
3 Stop condition:
o During stop mode, 3 ways valve will be in switch off position.
NO
L
N1 M
N2
* During pump down and force mode, fix 3 ways valve in close condition.
Control contents:
1 When indoor running in heat mode, OPEN the 2 ways valve.
2 When indoor running in cool mode, CLOSE the 2 ways valve.
3 Stop condition:
a. During stop mode, fix 2 ways valve in close condition.
NO
L
N1 M
N2
132
5V
External
12V Controller
mico
1
2
Panasonic
PCB
CN-THERMO
External Control Switch Control Panel OFF/ON Control Panel Power LED System Status
ON ON ON ON
ON OFF OFF OFF
OFF ON ON OFF
OFF OFF OFF OFF
10:34am , Mon
1 2
Turned off by external switch.
40 ˚c
23 44 CANCEL
˚c ˚c 18 ˚c
REMOTE ON
CONTROLLER OFF
LED
REMOTE ON ON
CONTROLLER
SIGNAL OFF OFF
ON
EXTERNAL
OFF
CONTROLLER
SWITCH
ON
UNIT OFF
133
Purpose:
- Heat pump ON/OFF function is use to turn OFF the high power consumption device (Heat pump, & Heater)
when there is energy or electric current limitation. Other optional function still can be operate under heat
pump and heater OFF condition.
Control Detail:
- This External Compressor Switch is possible to connect to Optional PCB only.
- Once the remocon select External Compressor Switch connection "YES", & Dip Switch on PCB "OFF"
This heat pump ON/OFF function will activate
- The ON/OFF signal of this External Compressor Switch is same as External Switch.
- When the External Compressor Switch is ON:
a) Heat pump system operate normally
- When the External Compressor Switch is OFF:
a) Heat pump, Indoor water pump & Heater ( Booster heater & Backup Heater ) need to turn OFF
b) Solar, Boiler and zone control can be operate follow normal control condition.
* pump delay OFF also included in this control
(There is NO pop up screen like External Switch when this External Compressor Switch is OFF.)
Purpose:
- Heater ON/OFF function is use to turn OFF the heater (backup heater & booster heater) when there is
energy or electric current limitation. Heat pump and other optional function still can operate.
Control detail:
- This External Compressor Switch is possible to connect to Optional PCB only.
- Once the remocon select External Compressor Switch connection "YES", & Dip Switch on PCB "ON"
This heater ON/OFF function will activate
- When the External Compressor Switch is ON:
a) Heat pump and heater operate normally
- When the External Compressor Switch is OFF:
a) Backup heater and booster heater cannot operate even heater request is ON.
b) Heat pump and option function (Solar, Boiler and zone control) can be operate follow normal control
condition.
(There is NO pop up screen like External Switch when this External Compressor Switch is OFF.)
134
Control contents:
- Heat/Cool Switch can only be set when Cool Function is "enable" at custom menu setting, & Extension PCB
select "YES" & Zone 1 not set "Pool" condition.
- This heat/cool switch control will be activate only when installer set the Heat/Cool Switch "USE" through
remocon.
- Once the Heat/Cool Switch Set "USE", remocon will check indoor send Signal to judge the option of mode
select.
a) When Heat/Cool Switch Contact Open : Remocon only can select Heat Mode, or Heat + Tank Mode, or
Tank Mode
b) When Heat/Cool Switch Contact Close : Remocon only can select Cool Mode, or Cool + Tank Mode, or
Tank Mode
- Operation ON/OFF will depend on remocon request.
- When Heat Mode is running with Contact Open, user change this setting to contact close, indoor will this
signal to remocon judge and change mode to cool and send back to indoor. And it is same as from cool
mode change to heat mode.
* This switch have higher priority, remocon follow indoor send signal when control activated.
* There is no effect to the operation when the mode running is only Tank Mode.
(Weekly Timer are ignored and cannot be set during Heat / Cool Switch is "Enable" Condition.)
135
+ DI2 Com
Digital Input
+ DI1 Com
- Com
For this function, following items need to be set on R/C (installer menu) –
- SG control = YES or NO
- Capacity up setting 1
o Heating capacity [50 ~ 150 %]
o DHW capacity [50 ~ 150 %]
- Capacity up setting 2
o Heating capacity [50 ~ 150 %]
o DHW capacity [50 ~ 150 %]
Control contents:
If SG control on remote control = "Yes", then following control only activate by digital input.
136
137
Purpose:
- After the demand control select YES, below control will activated.
o 0-10V Demand control
Control content:
o If start condition is fulfilled, indoor will receive the voltage signal from optional PCB. Indoor will send the rate
value to outdoor unit.
o Outdoor will change the current limit according to the percentage receive from indoor unit.
138
Control details:
o Indoor operate the unit according running mode request. Target temperature will follow holiday setting
temperature.
- If heat mode request is receive, Target Water Out Temperature will change according to holiday shift
temperature set.
[If heat is set OFF at holiday, unit, water pump and zone control will OFF]
- If tank mode request is receive, Target Tank Set Temperature will change according to the holiday
tank shift temperature set.
[If tank is set OFF at holiday, heat pump and tank heater will OFF]
o After days of holiday have been set, heat pump will stop and only resume operation at the end of holiday
countdown.
Start condition:
o Holiday timer set and the holiday timer start
* The day holiday mode was set is counted as day 1.
Stop condition:
o OFF/ON button is pressed.
o Holiday timer is reached.
Setting condition:
o Dry concrete parameter can be set through remote control under system setup.
o Parameters are possible to set up to 99 days with different target set temperature
Control details:
o Dry concrete mode will be activates when select ON from service setup.
o Once start dry concrete function, remote control will send step 1 setting temperature to indoor unit.
* This temperature is set at zone temperature. If system is 2 zones, both zone target temperature is set
as same temperature.
o Heat pump will start heat mode operation to room side with received target water outlet temperature.
* Heat pump will operate according to Heat pump Target Water Temperature.
o After complete day 1 setup operation, day 2 data will be send to indoor at 12.00am on the second day.
o Each preset data will be send every day until dry concrete mode is complete, unit will turns OFF and exit
dry concrete function.
o 3 ways valve and booster heater will turn OFF and 2 ways valve will turns ON.
Cancel condition:
o Dry concrete mode is complete and OFF signal is received.
o OFF signal is received by pressing OFF/ON button.
139
Compressor = OFF
112°C
97°C
Compressor
Frequency Reduced
110°C
97°C
Compressor
Frequency Maintain
108°C
97°C
Free
140
23°C
Max. 21°C
current
14°C value is
regulated
12°C
-20°C
-23°C
Compressor stop
Outdoor temperature
141
0
3. Heating accumulation time
-5
-10
-25
-30
-30 -20 -10 0 10 20 30
Outdoor Temperature (°C)
Free Free
Compressor 1 2 3 5 8 9
4 6 7
OFF
142
Free
25°C
22°C
Limited
Frequen cy
19°C
16°C
Compressor
stop
143
Hook
Screws Lift up
144
Press
145
11 : 00am,Mon
Press
& scroll to
“Installer setup”
[Screen 4]
- Range (0.1~99.9)L/min
[Screen 6]
146
11 : 00am,Mon
Press
& scroll to
“Installer setup”
[Screen 4]
- Range (0.1~99.9)L/min
[Screen 6]
NOTE:
1. Whenever at [Screen 5], if press SW to OFF, pump operation should be turned OFF.
2. Whenever at [Screen 6], if press SW to OFF, pump operation should be turned OFF.
147
Press ( + + ) SW’s
continuously for 5secs
148
During EEPROM default data setup process, display should be as shown below.
0.2s
Later
0.2s
Later
0.2s
Later
- Once EEPROM default data setup process is complete, initialization process will re-start from beginning.
149
11 : 00am,Mon
Press
& scroll to
“Installer setup”
[Screen 4]
[Screen 5] [Screen 6]
Next Page
150
- If suppose to select 10 stages, then setup will start from stage 1/10.
- Press or button to select set temperature.
- Press button to store latest status.
Return to [Screen 6]
151
1 Water pressure
Water pressure should not lower than 0.05 MPa (with inspects the Water Pressure Gauge). If necessary add
tap water into Tank Unit. Refer to Tank unit installation instruction for details on how to add water.
2 Pressure relief valve
o Check for correct operation of Pressure Relief Valve by turning on the lever to become horizontal.
o If you do not hear a clacking sound (due to water drainage), contact your local authorized dealer.
o Push down the lever after finish checking.
o In case the water keeps drained out from the unit, switch off the system, and then contact your local
authorized dealer.
Pressure relief
valve
Lever
Turn up
Pressure relief valve
Plug (turn
anticlockwise by
one complete turn)
WARNING
Be careful not to touch parts other than RCCB/ELCB test button when the power is supplied to Indoor Unit. Else, electrical
shock may happen.
o Push the “TEST” button on the RCCB/ELCB. The lever would turn down and indicate “0”, if it functions
normal.
o Contact authorized dealer if the RCCB/ELCB malfunction.
o Turn off the power supply to the Indoor Unit.
o If RCCB/ELCB functions normal, set the lever to “ON” again after testing finish.
152
If forget Password and cannot operate remote controller Items that can be set
Press for 5 sec. Actuator check (Manual ON/OFF all functional parts)
Password unlock screen appears, press Confirm and it shall (CAUTION) As there is no protection action, please be
reset. careful not to cause any error when operating
Password will become 0000. Please reset it again. each part (do not turn on pump when there is no
(CAUTION) Only display when it is locked by password. water etc.)
153
Select Confirm
15.1.4 Specifications
15.1.4.1 Specifications of fresh water was heat transfer medium in brazed heat
exchanger
154
155
Water leakage or
insufficient water flow
rate in the system
Excessive amount of
refrigerant
Inefficient compression
Insufficient refrigerant
(gas leakage)
Carry out the measurements of pressure, electric current, and temperature fifteen minutes after an operation is
started.
156
eg:
Error number
Blinking
157
Press SW to select
[Screen 4] “Error history”
158
159
160
Malfunction Caused:
1 Wrong model interconnected.
2 Wrong indoor unit or outdoor unit PCB (main) used.
3 Faulty indoor unit or outdoor unit PCB (main).
Abnormality Judgment:
Continue for 90 seconds.
No
Is the indoor and outdoor Match the compatible
model number matched? model.
Yes
161
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TANK connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in outdoor unit PCB (main)
- Replace the outdoor unit PCB (main)
162
Malfunction Caused:
1 Operation stop due to short circuit inside the water pump motor winding.
2 Operation stop due to breaking of wire inside the water pump motor.
3 Operation stop due to breaking of water pump lead wires.
4 Operation stop due to water pump motor IPM malfunction.
5 Operation error due to faulty indoor unit PCB.
Abnormality Judgment:
Continue for 5 seconds.
Yes
Replace the
water pump.
163
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TH1 connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in indoor unit PCB (main)
- Replace the indoor unit PCB (main)
164
Malfunction Caused:
1 3 way valves closed.
2 Faulty high pressure sensor.
3 Faulty indoor refrigerant pipe temperature sensor
4 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 minutes.
Yes
Is the 3 way valve closed? Open the 3 way valve.
No
Check for clogged
expansion valve or strainer.
165
Abnormality Judgment:
Continue for 5 seconds.
NO
H28 happens check connection at CN207 normal? ● Correct sensor connection
YES
NO
Measure resistance of sensor match characteristic? ● Change solar sensor
YES
166
Abnormality Judgment:
Continue for 5 seconds.
NO Correct
H31 happens check connector sensor at CN204 connection ● Correct connection
sensor connection
normal?
YES
YES
167
Abnormality Judgment:
Continue for 5 seconds.
NO
H36 check buffer tank sensor connection at CN205 normal? ● Correct connection
YES
YES
168
NO
Check the brand of indoor and outdoor unit both Panasonic? ● Use only Panasonic units.
● Change to Panasonic unit.
YES
169
Malfunction Caused:
1 Dust accumulation on the outdoor unit heat exchanger.
2 Air short circuit at outdoor unit.
3 2 way valve partially closed.
4 Faulty outdoor unit fan motor.
5 Refrigerant shortage (refrigerant leakage).
6 Clogged expansion valve or strainer.
7 Faulty outdoor pipe temperature sensor.
8 Faulty outdoor unit main PCB (main).
170
Abnormality Judgment:
Continue for 5 seconds.
NO ● Poor contact
Normal?
● Correct connection
YES
YES
● Defective PCB
● Replace PCB
171
Abnormality Judgment:
Continue for 5 seconds.
Turn off power check connector connection normal? ● Correct abnormal connection
YES
YES
Change PCB
172
Malfunction Caused:
1 Faulty water pump.
2 Water leak in system.
3 Faulty connector connection.
4 Faulty water flow switch.
5 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 10 seconds (but no judgment for 9 minutes after compressor startup/restart).
No
Is the CN-FLOW connector - Connector poor contact
Check the system water pump. connection normal? - Correct the connection
Yes
No Replace the faulty water Check the indoor water flow switch:
Is the water pump working?
pump. - Plug out connector from the indoor
unit PCB (main)
Yes - Dismantle the water flow switch
- Position the water flow switch in
Check the system water passage. reverse direction (downward)
- Measure the continuity of the water
flow switch
173
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue 4 times in 20 minutes.
174
Malfunction Caused:
1 Water flow in air-to-water heatpump indoor unit circuitry.
2 Faulty indoor unit water flow switch.
3 Faulty indoor unit water pump.
4 Faulty indoor unit PCB.
Abnormality Judgment:
Continue for 10 seconds.
No
- Defect in indoor unit PCB
- Replace the indoor unit PCB
175
Abnormality Judgment:
Continue for 5 seconds.
NO
Check CN205 connector on sub PCB normal? ● Correct connection
YES
YES
176
Abnormality Judgment:
Continue for 5 seconds.
YES
177
Malfunction Caused:
1 Faulty power supply connector connection.
2 Faulty connector connection.
3 Faulty indoor backup heater overload protector (OLP).
4 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 60 seconds.
Yes
Check indoor backup heater OLP Use a test pen to push
Check the indoor backup heater incoming continuity: this button to reset OLP
AC power supply (2): - Turn OFF power supply
- Turn ON power supply (2) & RCCB - Reset heater 1 OLP
- Measure the AC voltage between RCCB’s - Measure the continuity of OLP
L1 & N1
- Measure the AC voltage between PCB’s
AC2-L3 & AC2-N2 Multimeter to
- Defect in RCCB Is there any continuity?
measure continuity
- Replace RCCB
No - Terminal board assembly
Is measured voltage 230Vac? connector poor contact - Defect in indoor backup
- Correct the connection or No heater OLP
Yes replace the indoor unit - Replace indoor backup
PCB (main) heater OLP
Check the CN-OLP1 connector connection:
- Turn OFF the power
- Check the connector connection - Defect in indoor unit
Yes PCB (main)
No - Replace the indoor unit
Is the CN-OLP1 connector - Connector poor contact PCB (main)
connection normal? - Correct the connection
Yes
178
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
Yes
Yes
- Defect in indoor unit PCB (main)
- Replace the indoor unit PCB (main)
179
Malfunction Caused:
1 Faulty connector connection.
2 Faulty indoor PCB.
3 Faulty indoor sub PCB.
Abnormality Judgment:
After 1 minute operation started.
NO
H74 happens check connection at CN-PWR normal? ● Correct connection at CN-PWR
YES
NO
Check CN-PWR 230/240 V? ● Abnormal AC POWER supply
YES
NO
Check CN-COMM situation on terminal 1 & 2 and 3 & 1 ● Replace sub PCB
YES
180
Malfunction Caused:
1 Faulty connector connection.
2 Faulty control panel.
3 Faulty indoor unit PCB (main).
Yes
- Defect in remote controller
Check the control panel Is the remote controller Yes (control panel)
cable connection. (control panel) voltage 5Vdc
- Replace the remote
(pin1 & 4) generated?
controller (control panel)
181
Malfunction Caused:
1 Faulty outdoor unit PCB (main).
2 Faulty indoor unit PCB (main).
3 Indoor-outdoor signal transmission error due to wrong wiring.
4 Indoor-outdoor signal transmission error due to breaking of wire in the connection wires between the indoor
and outdoor units.
5 Indoor-outdoor signal transmission error due to disturbed power supply waveform.
Abnormality Judgment:
Continue for 1 minute after operation.
No
Is the Vdc fluctuate Replace the outdoor unit
between 45-60Vdc? PCB (main).
Yes
Turn OFF the power and reconnect
terminal 3 wire. Turn ON the power
and again measure Vdc between
terminal 2 & 3 from the outdoor unit.
No
Is the Vdc fluctuate Replace the indoor unit
between 15-60Vdc? PCB (main).
182
Malfunction Caused:
1 Faulty connector connection.
2 Faulty tank booster heater overload protector (OLP).
3 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 60 seconds.
Yes
Check the CN-OLP2 connector connection:
- Turn OFF the power
- Check the connector connection
183
Malfunction Caused:
1 Insufficient power supply.
2 Faulty outdoor unit PCB (noise filter/main).
184
Malfunction Caused:
1 Faulty water pump.
2 Insufficient water flow rate in system.
3 Water leak in system.
4 2/3 way closed.
5 Clogged expansion valve or strainer.
6 Excessive refrigerant.
7 Faulty outdoor high pressure sensor.
8 Faulty outdoor unit PCB (main).
Yes
No Replace the faulty water Is the 2/3 way valve closed? Open the 2/3 way valve.
Is the water pump working?
pump.
No
Yes
Check for clogged
Check the system water
expansion valve or strainer.
flow rate.
- Replace the expansion
Is the expansion valve or Yes valve and/or strainer
Is the water pump speed No strainer clogged (ice formed)? - Reclaim and recharge
Readjust the water pump
adjusted according to system refrigerant
speed. No
hydraulic external static pressure?
Yes Check refrigerant amount.
185
Malfunction Caused:
1 Faulty water pump.
2 Insufficient water flow rate in system.
3 Water leak in system.
4 2 way valve partially closed.
5 Clogged expansion valve or strainer.
6 Refrigerant shortage (refrigerant leakage).
7 Faulty indoor refrigerant liquid temperature sensor.
8 Faulty indoor unit PCB (main).
Check the 2 way valve. Yes Replace the indoor unit PCB
(main).
No
Is the 2 way valve partially Yes
Open the 2 way valve. Replace the indoor refrigerant
closed? liquid temperature sensor.
No
186
Malfunction Caused:
1 Dust accumulation on the outdoor unit heat exchanger.
2 Air short circuit at outdoor unit.
3 Faulty water pump.
4 Insufficient water flow rate in system.
5 Water leak in system.
6 2/3 way valve closed.
7 Clogged expansion valve or strainer.
8 Excessive refrigerant.
9 Faulty outdoor high pressure sensor and switch.
10 Faulty outdoor unit PCB.
Abnormality Judgment:
Continue 4 times in 20 minutes.
187
Malfunction Caused:
1 Compressor terminal disconnect.
2 Faulty outdoor unit PCB (main).
3 Faulty compressor.
Abnormality Judgment:
Continue 4 times in 20 minutes.
No - IPM defective
Is the blinking of the 6 LEDs in
- Replace the outdoor unit PCB
same sequence/condition?
(main)
Yes Inverter
Replace the compressor. checker
188
Malfunction Caused:
1 Operation stop due to short circuit inside the fan motor winding.
2 Operation stop due to breaking of wire inside the fan motor.
3 Operation stop due to breaking of fan motor lead wires.
4 Operation stop due to fan motor Hall IC malfunction.
5 Operation error due to faulty outdoor unit PCB.
Abnormality Judgment:
Continue 2 times in 30 minutes.
No Is the fan motor power supply voltage No Replace the outdoor unit
Does it rotate? ~325Vdc (pin1 & 4) generated? PCB (main).
Yes Yes
Stop the fan motor. Is the fan motor control voltage No Replace the outdoor unit
15Vdc (pin5 & 4) generated? PCB (main).
189
Malfunction Caused:
1 Excessive refrigerant.
2 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue 3 times in 20 minutes.
Yes
No
Replace the outdoor unit
PCB (main).
190
Malfunction Caused:
1 Faulty compressor tank temperature sensor.
2 2/3 way valve closed.
3 Refrigerant shortage (refrigerant leakage).
4 Clogged expansion valve or strainer.
5 Faulty outdoor unit PCB (main).
6 Faulty compressor.
Abnormality Judgment:
Continue 4 times in 30 minutes.
No
Yes - Replace the outdoor unit
Is abnormality happened
PCB (main)
Check for gas leakage. again?
- Replace the compressor
No
- Repair the pipe flare or Procedure complete
Is the oil oozing out from Yes union nuts
the 2/3 way valve? - Reclaim and recharge
refrigerant
No
191
Malfunction Caused:
1 Faulty outdoor unit fan motor.
2 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue 3 times in 30 minutes.
No
Yes
- Defect in IPM
- Replace the outdoor unit
PCB (main)
192
Malfunction Caused:
1 Faulty outdoor unit PCB (main).
2 Faulty compressor.
Abnormality Judgment:
Continue for 7 times.
193
Malfunction Caused:
1 Faulty water inlet or indoor refrigerant liquid temperature sensors.
2 2/3 way valve closed.
3 Refrigerant shortage (refrigerant leakage).
4 Clogged expansion valve or strainer.
5 Faulty outdoor unit PCB (main).
6 Poor compression of compressor.
Abnormality Judgment:
Continue 2 times in 20 minutes.
Does it conform to the No Replace the water inlet or indoor Check for clogged
sensor characteristic chart? ref. liquid temperature sensor. expansion valve or strainer.
No
Yes - Replace the outdoor unit
Is abnormality happened
Check for gas leakage. PCB (main)
again?
- Replace the compressor
194
Malfunction Caused:
1 Faulty sensor.
2 Faulty connector connection.
3 Faulty outdoor unit PCB (noise filter/main).
4 Faulty four way valve.
Abnormality Judgment:
Continue 4 times in 30 minutes.
Four way valve coil Yes Correct the four way valve
disconnected (loose)? coil.
Check the indoor pipe No
temperature sensor. Yes
Is the harness out of the
Reconnect the harness.
CN-HOT connector?
Does it conform to the No Replace the indoor pipe No
sensor characteristic chart? temperature sensor. Check the continuity of the
Yes four way valve coil.
Yes
Replace the four way valve.
195
Malfunction Caused:
1 Faulty connector connection.
2 Faulty switch.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 1 minute.
No
Is the CN-PSW1 connector - Connector poor contact
connection normal? - Correct the connection
Yes
196
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
4 Faulty High Pressure Switch
5 Refrigerant shortage (refrigerant leakage).
Abnormality Judgment:
1 times occurrence within 2550 minutes.
Yes
No
Is the refrigerant cycle pressure normal? - Recharge Gas.
Yes
300
25
250
Resistance (KΩ)
Resistance (KΩ)
20
200
15
150
10 100
5 50
0
0
-10 0 10 20 30 40 50
-10 0 10 20 30 40 50
Temperature (°C)
Temperature (°C)
197
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty indoor unit PCB.
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TH3 connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in indoor unit PCB
- Replace the indoor unit PCB
198
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
Yes
Yes
- Defect in outdoor unit PCB (main)
- Replace the outdoor unit PCB (main)
199
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TH1 connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in indoor unit PCB (main)
- Replace the indoor unit PCB (main)
200
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
Yes
Yes
- Defect in outdoor unit PCB (main)
- Replace the outdoor unit PCB (main)
201
Malfunction Caused:
1 Power supply surge.
2 Compressor windings not uniform.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue 4 times in 10 minutes.
Yes
Are the compressor’s winding
Operate the system. Verify PFC resistance (U-V, V-W, U-W)
abnormality by measuring the DC uniform?
voltage between DCP-OUT and DCN-
OUT of the outdoor unit PCB (main).
No
Replace the compressor.
Is the DC voltage between DCP- Yes - Defect in PFC circuitry
OUT and DCN-OUT normal - Replace the outdoor unit
(between 285-315Vdc)? PCB (main) Yes Replace the outdoor unit
PCB (main).
No
202
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TH1 connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in outdoor unit PCB (main)
- Replace the outdoor unit PCB (main)
203
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty outdoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
Yes
Yes
- Defect in outdoor unit PCB (main)
- Replace the outdoor unit PCB (main)
204
Malfunction Caused:
1 Faulty connector connection.
2 Faulty sensor.
3 Faulty indoor unit PCB (main).
Abnormality Judgment:
Continue for 5 seconds.
No
Is the CN-TH1 connector - Connector poor contact
connection normal? - Correct the connection
Yes
Yes
- Defect in indoor unit PCB (main)
- Replace the indoor unit PCB (main)
205
Malfunction Caused:
1 CT defective.
2 Faulty outdoor unit PCB (main).
3 Compressor defective (low compression).
Abnormality Judgment:
Continue 3 times in 20 minutes.
No
Is the pressure unchanged (same No Replace the outdoor unit
Check for gas leakage. as when compressor stop)? PCB (main).
Yes
- Repair the pipe flare or
Is the oil oozing out from Yes union nuts While the system is still in heating operation,
the 2/3 way valve? - Reclaim and recharge further check (by touching) if:
refrigerant - Compressor discharge pipe is cold
No - Compressor body is warm
to confirm the compressor low compression.
Turn ON the power, and
operate heating operation. Yes
Replace the compressor.
206
Malfunction Caused:
1 Dust accumulation in the outdoor unit heat exchanger.
2 Air short circuit at outdoor unit.
3 2 way valve closed.
4 Faulty outdoor unit fan motor.
5 Clogged expansion valve or strainer.
6 Excessive refrigerant.
7 Faulty outdoor high pressure sensor.
8 Faulty outdoor unit PCB (main).
207
WARNING
High Voltage are generated in the electrical parts area by the capacitor. Ensure that the capacitor has discharged sufficiently before proceeding
with repair work. Failure to heed this caution may result in electric shocks.
Lift up
1. Remove 2 screws.
208
Screws
Screws
Insert the
driver and
slightly turn.
Flat-blade
screwdriver
Bottom
case
209
210
17.8 To Remove Pressure Relief Valve, Air Purge Valve and Flow Sensor
Flow Sensor
C
3. Pull outward to remove
Pressure Relief Valve.
Pressure Relief Valve
Packing
211
3. Remove 2 screws.
Water Pump
Bottle Complete
212
213
9.200
9.000
Capacity (kW)
8.800
8.600
8.400
8.200
-15 -11 -7 -3 1 5 9 13 17 21 25
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
-15 -11 -7 -3 1 5 9 13 17 21 25
214
10.000
9.000
Capacity (kW)
8.000
7.000
6.000
5.000
16 19 22 25 28 31 34 37 40 43
3.000
2.500
Input Power (kW)
2.000
1.500
1.000
0.500
16 19 22 25 28 31 34 37 40 43
215
12.000
11.000
Capacity (kW)
10.000
9.000
8.000
7.000
16 19 22 25 28 31 34 37 40 43
3.500
3.000
Input Power (kW)
2.500
2.000
1.500
1.000
16 19 22 25 28 31 34 37 40 43
216
9.500
8.500
Capacity (kW)
7.500
6.500
5.500
4.500
16 19 22 25 28 31 34 37 40 43
3.000
2.500
Input Power (kW)
2.000
1.500
1.000
0.500
16 19 22 25 28 31 34 37 40 43
217
10.000
9.500
Capacity (kW)
9.000
8.500
8.000
7.500
3 6 9 12 15 18 21 24 27 30
2.100
2.000
Input Power (kW)
1.900
1.800
1.700
1.600
3 6 9 12 15 18 21 24 27 30
218
7.500
7.000
Capacity (kW)
6.500
6.000
5.500
5.000
3 6 9 12 15 18 21 24 27 30
2.500
2.400
Input Power (kW)
2.300
2.200
2.100
2.000
3 6 9 12 15 18 21 24 27 30
219
13.000
12.000
Capacity (kW)
11.000
10.000
9.000
8.000
-15 -11 -7 -3 1 5 9 13 17 21 25
6.000
5.000
Input Power (kW)
4.000
3.000
2.000
1.000
-15 -11 -7 -3 1 5 9 13 17 21 25
220
12.500
11.500
Capacity (kW)
10.500
9.500
8.500
7.500
16 19 22 25 28 31 34 37 40 43
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
16 19 22 25 28 31 34 37 40 43
221
16.000
15.000
Capacity (kW)
14.000
13.000
12.000
11.000
16 19 22 25 28 31 34 37 40 43
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
16 19 22 25 28 31 34 37 40 43
222
12.000
11.000
Capacity (kW)
10.000
9.000
8.000
7.000
16 19 22 25 28 31 34 37 40 43
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
16 19 22 25 28 31 34 37 40 43
223
12.500
12.000
Capacity (kW)
11.500
11.000
10.500
10.000
3 6 9 12 15 18 21 24 27 30
4.000
3.500
Input Power (kW)
3.000
2.500
2.000
1.500
3 6 9 12 15 18 21 24 27 30
224
11.000
10.000
Capacity (kW)
9.000
8.000
7.000
6.000
3 6 9 12 15 18 21 24 27 30
3.800
3.700
Input Power (kW)
3.600
3.500
3.400
3.300
3 6 9 12 15 18 21 24 27 30
225
17.500
16.000
Capacity (kW)
14.500
13.000
11.500
10.000
-15 -11 -7 -3 1 5 9 13 17 21 25
6.000
5.000
Input Power (kW)
4.000
3.000
2.000
1.000
-15 -11 -7 -3 1 5 9 13 17 21 25
226
16.000
14.000
Capacity (kW)
12.000
10.000
8.000
6.000
16 19 22 25 28 31 34 37 40 43
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
16 19 22 25 28 31 34 37 40 43
227
22.000
20.000
Capacity (kW)
18.000
16.000
14.000
12.000
16 19 22 25 28 31 34 37 40 43
6.500
5.500
Input Power (kW)
4.500
3.500
2.500
1.500
16 19 22 25 28 31 34 37 40 43
228
17.000
15.000
Capacity (kW)
13.000
11.000
9.000
7.000
16 19 22 25 28 31 34 37 40 43
5.500
4.500
Input Power (kW)
3.500
2.500
1.500
0.500
16 19 22 25 28 31 34 37 40 43
229
17.000
16.500
Capacity (kW)
16.000
15.500
15.000
14.500
3 6 9 12 15 18 21 24 27 30
4.200
4.000
Input Power (kW)
3.800
3.600
3.400
3.200
3 6 9 12 15 18 21 24 27 30
230
13.500
12.500
Capacity (kW)
11.500
10.500
9.500
8.500
3 6 9 12 15 18 21 24 27 30
5.000
4.900
Input Power (kW)
4.800
4.700
4.600
4.500
3 6 9 12 15 18 21 24 27 30
231
232
Water In (°C) 12 19 23
Water Out (°C) 7 14 18
Outdoor Air (°C) Capacity (W) Input Power (W) Capacity (W) Input Power (W) Capacity (W) Input Power (W)
16 7500 1150 9100 1200 7000 1130
25 8350 1770 10900 1780 7000 1240
35 7000 2230 8300 2320 7000 1520
43 5520 2540 7690 2770 5600 1800
Water In (°C) 12 19 23
Water Out (°C) 7 14 18
Outdoor Air (°C) Capacity (W) Input Power (W) Capacity (W) Input Power (W) Capacity (W) Input Power (W)
16 7860 1180 13150 1400 10000 1730
25 12080 2900 15700 2050 10000 1970
35 10000 2560 12000 2670 10000 2400
43 7800 3800 11100 3190 8000 2850
Water In (°C) 12 19 23
Water Out (°C) 7 14 18
Outdoor Air (°C) Capacity (W) Input Power (W) Capacity (W) Input Power (W) Capacity (W) Input Power (W)
16 9200 1620 16400 2580 12200 2450
25 14400 3920 19200 3830 12200 2790
35 12200 4760 15000 4980 12200 2960
43 7750 3400 13800 5950 9700 4000
233
1 36
O/I 37 I/I 42
O/I 38 I/I 43
O/I 39 46
O/I 40 44
17
O/I 41
13
15
18
31 28
16
19
3
37 19
2
33
45 29 9
23
8 10
31
22 20
24
27 12
21 5
32
26 18
4
30 24
25
39
25
14 11
35 11
12 4 31
38
5
7
6
Note:
The above exploded view is for the purpose of parts disassembly and replacement.
The non-numbered parts are not kept as standard service parts.
234
REF.
SAFETY DESCRIPTION & NAME QTY. WH-SDC09H3E8 REMARK
NO.
1 BASE PAN 1 CWD521450
2 HOT WATER COIL - COMPLETE 1 ACXB90C00220
3 RECEIVER 1 CWB141039
4 CATCHER 2 CWH601011
5 FLARE NUT (5/8) 1 CWT251064
6 FLARE NUT 1 CWT251061
7 FLARE NUT (1/4) 1 CWT251063
8 WATER PUMP 1 CWB532116 O
9 FERRITE CORE 1 CWA431122
10 LEAD WIRE - FOR PUMP 1 ACXA60C06140 O
11 PRESSURE RELIEF VALVE 1 CWB621136 O
12 FILTER COMPLETE 1 CWB51C1021
13 FLOW SENSOR 1 CWB621137 O
14 PRESSURE GAUGE 1 CWB070003
15 HEATER ASS'Y 1 ACXA34K00080 O
16 SOUND PROOF MATERIAL 1 ACXG30-00680
17 AIR PURGE VALVE 1 ACXB62-00130 O
18 THERMOSTAT 4 CWA151074 O
19 CONTROL BOARD 1 CWH102629
20 ELECTRONIC CONTROLLER - MAIN 1 ACXA73C11510 O
21 TERMINAL BOARD ASS'Y (1 TO 5) 1 CWA28K1240 O
22 TERMINAL BOARD ASS'Y (A, B) 1 CWA28K1260 O
23 REACTOR 1 G0C103Z00003 O
24 HINGE 2 CWH611006
25 HINGE 2 CWH611007
26 RESIDUAL CURRENT CIRCUIT BREAKER 1 CWA181008 O
27 RESIDUAL CURRENT CIRCUIT BREAKER 1 K5KYYAY00003 O
28 SENSOR - CO. (WATER IN, OUT REF TEMP) 1 CWA50C3377 O
29 SENSOR - CO. (HEX WATER OUTLET) 1 CWA50C3378 O
30 REMOTE CONTROL COMPLETE 1 CWA75C4681 O
31 CABINET SIDE PLATE 2 CWE041850A
32 CABINET FRONT PLATE 1 CWE061396A
33 LOCK 2 CWH891004
34 DECORATION BASE ASS'Y 1 CWE35K1285
35 ACCESSORY - COMPLETE 1 CWH82C2174
36 INSTALLING HOLDER 1 CWH361103A
37 OPERATING INSTRUCTION 1 ACXF55-02060
38 OPERATING INSTRUCTION 1 ACXF55-02070
39 OPERATING INSTRUCTION 1 ACXF55-02090
40 OPERATING INSTRUCTION 1 ACXF55-02100
41 OPERATING INSTRUCTION 1 ACXF55-02110
42 INSTALLATION INSTRUCTION 1 ACXF60-03130
43 INSTALLATION INSTRUCTION 1 ACXF60-03260
44 BAG - COMPLETE (FLEXIBLE PIPE) 1 CWG87C900
45 INSTALLING HOLDER 1 CWH361119A
46 ACCESSORY - COMPLETE 1 CWH82C1754
Note:
All parts are supplied from PAPAMY, Malaysia (Vendor Code: 00029488).
“O” marked parts are recommended to be kept in stock.
235
REF.
SAFETY DESCRIPTION & NAME QTY. WH-SDC12H9E8 WH-SDC16H9E8 REMARK
NO.
1 BASE PAN 1 CWD521450 ←
2 HOT WATER COIL - COMPLETE 1 ACXB90C00220 ACXB90C00250
3 RECEIVER 1 CWB141039 ←
4 CATCHER 2 CWH601011 ←
5 FLARE NUT (5/8) 1 CWT251064 ←
6 FLARE NUT 1 CWT251061 ←
7 FLARE NUT (1/4) 1 CWT251063 ←
8 WATER PUMP 1 CWB532116 ← O
9 FERRITE CORE 1 CWA431122 ←
10 LEAD WIRE - FOR PUMP 1 ACXA60C06140 ← O
11 PRESSURE RELIEF VALVE 1 CWB621136 ← O
12 FILTER COMPLETE 1 CWB51C1021 ←
13 FLOW SENSOR 1 CWB621137 ← O
14 PRESSURE GAUGE 1 CWB070003 ←
15 HEATER ASS'Y 1 ACXA34K00090 ← O
16 SOUND PROOF MATERIAL 1 ACXG30-00680 ←
17 AIR PURGE VALVE 1 ACXB62-00130 ← O
18 THERMOSTAT 4 CWA151074 ← O
19 CONTROL BOARD 1 CWH102629 ←
ELECTRONIC CONTROLLER -
20 1 ACXA73C11520 ACXA73C11530 O
MAIN
21 TERMINAL BOARD ASS'Y (1 TO 5) 1 CWA28K1240 ← O
22 TERMINAL BOARD ASS'Y (A, B) 1 CWA28K1238 ← O
23 REACTOR 1 G0C103Z00003 ← O
24 HINGE 2 CWH611006 ←
25 HINGE 2 CWH611007 ←
RESIDUAL CURRENT CIRCUIT
26 2 CWA181008 ← O
BREAKER
SENSOR - CO. (WATER IN, OUT
28 1 CWA50C3377 ← O
REF TEMP)
SENSOR - CO. (HEX WATER
29 1 CWA50C3378 ← O
OUTLET)
30 REMOTE CONTROL COMPLETE 1 CWA75C4681 ← O
31 CABINET SIDE PLATE 2 CWE041850A ←
32 CABINET FRONT PLATE 1 CWE061396A ←
33 LOCK 2 CWH891004 ←
34 DECORATION BASE ASS'Y 1 CWE35K1285 ←
35 ACCESSORY - COMPLETE 1 CWH82C2174 ←
36 INSTALLING HOLDER 1 CWH361103A ←
37 OPERATING INSTRUCTION 1 ACXF55-02060 ←
38 OPERATING INSTRUCTION 1 ACXF55-02070 ←
39 OPERATING INSTRUCTION 1 ACXF55-02090 ←
40 OPERATING INSTRUCTION 1 ACXF55-02100 ←
41 OPERATING INSTRUCTION 1 ACXF55-02110 ←
42 INSTALLATION INSTRUCTION 1 ACXF60-03130 ←
43 INSTALLATION INSTRUCTION 1 ACXF60-03260 ←
BAG - COMPLETE (FLEXIBLE
44 1 CWG87C900 ←
PIPE)
45 INSTALLING HOLDER 1 CWH361119A ←
46 ACCESSORY - COMPLETE 1 CWH82C1754 ←
Note:
All parts are supplied from PAPAMY, Malaysia (Vendor Code: 00029488).
“O” marked parts are recommended to be kept in stock.
236
46
36
23
38 37
40
41
45
43
42
44
39 37
40
41
27
32
42
19 48
47
32
44
48
49 50
Note:
The above exploded view is for the purpose of parts disassembly and replacement.
The non-numbered parts are not kept as standard service parts.
237
18
17
24
26
8
22
15
52
13 11
51
35 10
34
20
5 21
12
26
16
25
51
2
5
6
6 33
4
1
14
Note:
The above exploded view is for the purpose of parts disassembly and replacement.
The non-numbered parts are not kept as standard service parts.
238
56 55
54
53
58
30 31
57
29
Note:
The above exploded view is for the purpose of parts disassembly and replacement.
The non-numbered parts are not kept as standard service parts.
239
REF.
SAFETY DESCRIPTION & NAME QTY. WH-UD09HE8 WH-UD12HE8 WH-UD16HE8 REMARK
NO.
1 BASE PAN ASS’Y 1 ACXD52K00260 ← ←
2 COMPRESSOR 1 5JD420XBA22 ← ← O
3 CRANKCASE HEATER 1 CWA341053 ← ←
BUSHING - COMPRESSOR
4 3 CWH50055 ← ←
MOUNT
NUT - COMPRESSOR
5 3 CWH561049 ← ←
MOUNT
GASKET FOR TERMINAL
6 3 CWB811017 ← ←
COVER
7 CONDENSER COMPLETE 1 CWB32C3986 ← ←
8 TUBE ASSY (CAP.TUBE) 1 CWT07K1606 ← ←
9 3-WAYS VALVE (GAS) 1 CWB011251 ← ← O
10 4-WAYS VALVE 1 CWB001046 ← ← O
11 HIGH PRESSURE SENSOR 1 CWA501463 ← ← O
12 DISCHARGE MUFFLER 1 CWB121014 ← ←
13 ACCUMULATOR 1 CWB131026A ← ←
14 3-WAYS VALVE 1 ACXB01-00040 ← ← O
15 2-WAYS VALVE 1 CWB021637 ← ← O
16 EXPANSION VALVE 1 CWB051049 ← ←
17 SOUND PROOF MATERIAL 1 ACXG30-00850 ← ←
18 SOUND PROOF MATERIAL 1 CWG302266 ← ←
19 SOUND PROOF BOARD 1 CWH15K1031 ← ←
V-COIL COMP. (4-WAY
20 1 CWA43C2169J ← ← O
VALVE)
V-COIL COMP.
21 1 CWA43C2602 ← ← O
(EXPANSION VALVE)
V-COIL COMP. (2 WAY
22 1 CWA43C2607 ← ← O
VALVE)
SENSOR - COMP.
23 (OUTDOOR AIR PIPE 1 CWA50C2730 ← ← O
TEMP CN-TH1)
SENSOR - COMP.
24 1 CWA50C2577 ← ← O
(DEFROST TEMO CN-TH2)
SENSOR-COMP.
25 1 CWA50C2576 ← ← O
(DISHARGE TEMP CN-DIS)
SENSOR - COMP. (EVA
26 1 CWA50C3204 ← ← O
EXIT TEMP CN-TH3)
CABINET REAR PLATE-
27 1 CWE02C1059 ← ←
COMPLETE
28 CONTROL BOARD CASING 1 CWH10K1049 ← ←
29 TERMINAL BOARD ASS’Y 1 CWA28K1214 ← ← O
ELECTRONIC
30 1 CWA747838 ← ← O
CONTROLLER - NF
ELECTRONIC
31 1 ACXA73C08820R ACXA73C08830R ACXA73C08840R O
CONTROLLER (MAIN)
32 REACTOR 3 G0C293J00001 ← ← O
SENSOR - (COMP TANK
33 1 CWA50C2629 ← ← O
TEMP CN-TANK)
34 TERMINAL COVER 1 CWH171039A ← ←
35 NUT-TERMINAL COVER 1 CWH7080300J ← ←
36 FAN MOTOR BRACKET 1 CWD54K1084 ← ←
SCREW-FAN MOTOR
37 8 CWH551040J ← ←
BRACKET
38 FAN MOTOR (UPPER) 1 EHDS83CAC ← ← O
39 FAN MOTOR (LOWER) 1 EHDS83DAC ← ← O
SCREW - FAN MOTOR
40 8 CWH551323 ← ←
MOUNT
41 PROPELLER FAN ASSY 2 CWH00K1006 ← ←
42 NUT 2 CWH561092 ← ←
43 CABINET FRONT PLATE 1 CWE061098A ← ←
44 DISCHARGE GRILLE 2 CWE201073 ← ←
CABINET SIDE PLATE
45 1 CWE04K1023A ← ←
ASSY
240
Note:
All parts are supplied from PAPAMY, Malaysia (Vendor Code: 00029488).
“O” marked parts are recommended to be kept in stock.
241