Professional Documents
Culture Documents
200W Constant Voltage PWM Output LED Driver: Series
200W Constant Voltage PWM Output LED Driver: Series
User’s Manual
2
IP67 05
■ ■
‧ ‧
compliant IEEE1789-2015 ‧
‧Ⅱ ‧
‧ ‧
‧ ‧
‧ ‧
‧ ‧
‧ type
‧
■
~
℃℃
■
DIMMING OPERATION
Vo+(Red)
AC/L(Brown) Vo-(Black)
AC/N(Blue) PWM-200 DIM-/DA-(Pink)**
DIM+/DA+(Purple)*
ON
Output DC current T ON
Duty cycle(%) = ×100%
T
+
+V + 70%
60%
-
-V - 50%
DIM+ 40%
+
30%
Additive Voltage 10%
- 20%
DIM-
1% 10%
◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100%
90%
Duty cycle of output current (%)
Note : 1. Min. duty cycle of output current is about 1%, and the dimming input is about 6KΩ or 0.6VDC, or 10V PWM signal with 6% duty cycle.
2. The duty cycle of output current could drop down to 0% when dimming input is less than 6KΩ or less than 0.6VDC,
or 10V PWM signal with duty cycle less than 6%.
※DALI interface
+V
-V
DC OUT
Push Button
DA+
AC/L
AC/N
DA-
230VAC
100 100
80 80
230VAC 230VAC
Input only 110VAC Input only
60 60
50
LOAD (%)
LOAD (%)
40 40
20 20
※ Tcase at 75℃
1
100 0.95
0.9
93 0.85
0.8
0.75
80
0.7
0.65 230VAC
70 0.6
PF
0.55 115VAC
0.5
LOAD (%)
60 277VAC
0.45
0.4
50 0.35
0.3
40 0.25
0.2
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
100 110 125 135 150 180 200 220 240 260 280 305
LOAD
INPUT VOLTAGE (V) 60Hz
20% 96
19% 95
18% 94
17% 93
92
EFFICIENCY(%)
16%
91
15% 90
14% 89
THD
LOAD LOAD
LIFE TIME
120
100
80
LIFETIME(Kh)
60
40
20
0
25 30 35 40 45 50 55 60 65 70 75 80 85
Tcase( ℃ )
Block Diagram
PFC fosc : 50~120KHz
PWM fosc : 60~130KHz
DIM+/DA+
O.T.P. O.L.P. DETECTION DIM-/DA-
CIRCUIT
Mechanical Specification
Case No. PWM-200 Unit:mm
AC/L(Brown) Vo+(Red)
Vo-(Black)
AC/N(Blue) tc2 97.5
5
68
60 DIM-/DA-(Pink)
4.
34
ψ
tc1
DIM+/DA+(Purple)
2-
5
Installation Manual
-
-V(BLACK) LED Strip
+
AC/L(BROWN)
+V(RED)
AC/N(BLUE) DIM-/DA-(PINK)
- ‧DALI Dimmer
+ ‧0~10Vdc or 10V PWM
DIM+/DA+(PURPLE) or resistance Dimmer
◎Cautions
‧Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure
that it cannot be re-connected inadvertently!
‧Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when
the adjacent device is a heat source.
‧Mounting orientations other than standard orientation or operate under high ambient temperature may increase the
internal component temperature and will require a de-rating in output current.
‧Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer
to its specification.
‧For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is
tight so that water cannot intrude into the system.
‧For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series
require 0.15mA each unit.
‧Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.
‧Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30
minutes.
‧The power supply is considered as a component that will be operated in combination with final equipment. Since EMC
performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC
Directive on the complete installation again.