Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

We Hear It All The Time . . .

“Best Stuff I Ever Used”

ALL METALS Ideal for joining dissimilar


ALL PLASTICS metals and other materials.
Leak Lock is a proven
NO HYDROCARBONS formulation that will stick to
NO SILICONES all clean surfaces and can be
used to prevent vibration
NON TOXIC
from loosening nuts, bolts,
CHEMICALLY RESISTANT plugs and fittings.

GUARANTEES A PERFECT SEAL


... UNDER ALL CONDITIONS
AIR
REFRIGERATION CONDITIONING PLUMBING AUTOMOTIVE MARINE ELECTRICAL

Hot or cold, Leak Lock does its job. It never hardens and it never becomes brittle. This
means that regardless of temperatures and physical shock, Leak Lock will always
maintain a perfect seal. Ideal for use with pressure as well as vacuum service.

Effectively seals and is resistant to all refrigerants, oils, water and most
chemicals, both liquids and gases. Give Leak Lock a try and let us hear from you.
We want to hear about the best stuff you ever used.

11114 REICHOLD ROAD TELEPHONE: 1-800-359-5599


GULFPORT, MS, USA FAX: 1-228-896-9544
http://www.highsidechem.com e-mail: admin@highsidechem.com

Highside Chemical Products are available through local wholesalers and distributors worldwide.
Pipe Joint Sealant
WHAT IS LEAK LOCK?— Leak Lock is a state of the art high joints, gasket surfaces and all mating surfaces where a fluid-tight
strength, pipe joint sealant consisting of chemically resistant film seal is required. Special Applications— Leak Lock is ideal for
formers, plasticers, reinforcing fillers and solvents. joining dissimilar metals and materials. Prevents loosening of nuts,
bolts, plugs and fittings. Call Highside for specific applications and
HOW IT WORKS— When Leak Lock is applied to pipe joints, it
compatibility.
adheres to the mating surfaces. After joints are assembled, Leak
Lock sets to form a chemically resistant flexible fluid-tight seal. TYPICAL PHYSICAL PROPERTIES:
Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . 25,000 - 100,000 cPs
HOW TO USE IT— Leak Lock should be applied to clean joint
Consistency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . flowable paste
surfaces, either with the applicator brush or any convenient spatula.
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . light blue / light gray
Apply Leak Lock to both mating surfaces. Tack should be allowed
Solvent . . . . . . . . . . . . . . . . . . . . . . . . . . ethanol and isopropanol
to develop before joints are assembled.
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . full vacuum to 10,000 psi
WHERE TO USE— Leak Lock can be used on all metal or plastic Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . -200°F to +400°F
materials, including but not limited to, aluminum, aluminum alloys, Toxicity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . nontoxic
cast irons, copper, copper alloys, (brass, bronze, etc.), magnesium Shelf Life . . . . . . . . . . . . . . . . . . . . . . . . . . indefinite when sealed
and magnesium alloys, carbon steels, stainless steels, galvanized
surfaces, PVC, CPVC, ABS, fiberglass, black polypropylene, and Material Safety Data Sheet is available from Highside or can be
kynar. Leak Lock should be applied to threaded joints, flanged downloaded from our web site: http://www.highsidechem.com

LEAK LOCK— SUCCESSES


The following is a partial list of the materials and fluids that Leak Lock has successfully sealed:
REFRIGERANTS: SOLVENTS: Chloroform Xenon
All CFC’s, HFC’s, HCFC’s and PFC’s Water (soft, hard, potable) Ethylene Dichloride Tetrafluoromethane
including but not limited to: Seawater (saltwater) Trichlroethylene Helium
R-717 (ammonia) Pentane Propylene Dichloride
FUEL GASES:
R-744 (carbon dioxide) Hexane Aliphatic Solvents
Natural Gas
R-11 (trichlorofluoromethane) Cyclohexane Acids, Dilute
LPG “Liquified Petroleum Gas”
R-12 (dichlorodifluoromethane) Heptane Aromatic Solvents
LNG “Liquified Natural Gas”
R-21 (dichlorofluoromethane) Cyclohexane Glycerine
Propane
R-22 (chlorodifluoromethane) Petroleum Napthas Chlorinated Solvents
n-Butane
R-113 (1, 2trichlorotrifluoroethane) Mineral Spirits
INDUSTRIAL GASES: Isobutane
R-114 (1, 2dichlorotetrafluoroethane) Toluene
Acetylene
R-40 (methyl chloride) Xylene FUELS:
Chlorine, Anhydrous
R-30 (methylene chloride) Perchloroethylene Gasoline (petrol, motor fuel)
Air
R-290 (propane) D-Limonene Aviation Fuels (avgas, jet fuel)
Carbon Monoxide
R-764 (sulfur dioxide) Turpentine Fuel Oils, Diesel Fuel Oils, Gas
Ammonia, Anhydrous
R-134a (1, 1, 2-tetrafluoroethane) Pine Oil Turbine Oils, Kerosene, Gas Oil.
Argon
R-13, R-13bl, R-500, R-502, Lacquer Diluent
n-Butane OILS:
R-503, R-123, R-124, R-401A, Rubber Solvent
Carbon Dioxide Mineral Oils, Soybean Oil, Coconut
R-401B, R-402A, R-402B, R- VM&P Naptha
Ethane Oil, Tall Oil, Peanut Oil, Rapeseed
403B, R-406A, R-408A, R-409A, Stoddard Solvent
Ethylene Chloride Oil, Menhaden Oil, Vegetable Oil,
R-23, R-23fa, R-404A, R-407A, 140°F Solvent
Fluorine Animal Oil, Hydraulic Oils, Crude
R-407B, R-407C, R-410A, R-507, Deodorized Kerosene
Hydrogen Oil.
R-508. Medium-flash Aromatic Naptha
Methane * Leak Lock is not recommended
High-flash Aromatic Naptha
Neon for use with alcohols.
REFRIGERATION OILS Dipentene
Nitrogen
Mineral Oils, Napthenic Methylene Chloride CURE TIME:
Nitrous Oxide
Mineral Oils, Paraffinic 1, 1, 1-Trichloroethane Leak Lock will cure and be ready for
Oxygen (Industrial only)
Polyalphaolefins 2-Nitropropane service in as little as 20 minutes or
Propane no more than 24 hours depending
Alkylbenzenes Orthodichlorobenzene
Propylene on pipe size and temperature of
Polyvinylether Monochlorobenzene
Silane application.
Polyol Ester

Highside Chemical, Inc. • 11114 Reichold Road • Gulfport, MS, USA


Telephone: 1-800-359-5599 • Fax: 1-228-896-9544
http://www.highsidechem.com • e-mail: admin@highsidechem.com

You might also like