Professional Documents
Culture Documents
Bush BTV17 Orion Combi 3601VT Goodmans GTV-371VCR
Bush BTV17 Orion Combi 3601VT Goodmans GTV-371VCR
CONTENTS
A2-1
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS 1-3: TV/VCR BLOCK (Refer to Fig. 1-3)
AND P.C. BOARDS 1. Remove the 2 screws 1.
2. Disconnect the following connectors:
1-1: BACK CABINET (Refer to Fig. 1-1)
(CP351, CP757, CP302, CP403 and CP401).
1. Remove the 4 screws 1. 3. Unlock the support 2.
2. Remove the 2 screws 2. 4. Remove the TV/VCR Block in the direction of arrow.
3. Remove the 2 screws 3 which are used for holding the
Back Cabinet. 1
4. Remove the AC cord from the AC cord hook 4. 1
Front Cabinet
5. Remove the Back Cabinet in the direction of arrow.
Front Cabinet
2
UP TO
1 RELEASE
1 TV/VCR Block
2 Fig. 1-3
VCR Block
Fig. 1-4
Fig. 1-2
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: DECK SHIELD PLATE AND BOTTOM SHIELD
1
PLATE (Refer to Fig. 1-5) 1
3
1
Syscon PCB
2
2
(B)
2 3
3
Syscon PCB
2 1
Shield Plate Bottom
4
Fig. 1-5
Deck Holder
Fig. 1-7
B1-2
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DECK PARTS NOTE
2-1: TOP BRACKET (Refer to Fig. 2-1) When you install the Tape Guide L, install as shown in the
circle of Fig. 2-3-B. (Refer to Fig. 2-3-B)
1. Remove the 2 screws 1.
2. Slide the 2 supports 2 and remove the Top Bracket.
NOTE
Tape Guide L
When you install the Top Bracket, install the screw (1)
first, then install the screw (2).
REC Lever
(2) 1 (1) 1
Top Bracket
Top Bracket
• The REC Lever is not installed on the Video Cassette Player. Fig. 2-3-B
Tape Guide R
Cassette Side L Main Chassis
Flap Lever
Fig. 2-4
REC Lever
Locker R 1
1
Tape Guide L
Cassette Side R Locker L
Cassette Side L
1
Fig. 2-5
1
Main Chassis
• The REC Lever is not installed on the Video Cassette Player. Fig. 2-3-A
B2-1
DISASSEMBLY INSTRUCTIONS
2-6: LINK ASS'Y (Refer to Fig. 2-6) 2-9: TENSION ASS'Y (Refer to Fig. 2-9-A)
1. Set the Link Ass'y to the Eject position. 1. Move the Inclined S Ass'y to the back side.
2. Remove the (A) side of the Link Ass'y first, then remove 2. Unlock the support 1 and remove the S Reel Stopper.
the (B) side. 3. Remove the Tension Spring.
4. Unlock the support 2 and remove the Tension Arm
Ass'y.
5. Remove the Tension Adjust.
6. Unlock the 2 supports 3 and remove the Tension Band
Ass'y.
Link Ass'y
7. Unlock the support 4 and remove the Tension Holder.
Tension Adjust
3
(B)
(A) Link Ass'y 3 Tension Band Ass'y
Main Chassis
Main Chassis
1 Fig. 2-9-B
Deck PCB
(BOT) 2-10: T BRAKE ASS'Y (Refer to Fig. 2-10)
Link Lever
1. Remove the T Brake Spring.
2. Remove the T Brake Ass'y.
T Brake Ass'y
• Screw Torque: 5 ± 0.5kgf•cm
Fig. 2-7
Main Chassis
Sensor Cover L
Deck PCB
(EOT) Fig. 2-10
2
1
2
Fig. 2-8
B2-2
DISASSEMBLY INSTRUCTIONS
2-11: S REEL/T REEL ASS'Y (Refer to Fig. 2-11) NOTE
1. Remove the Idler Ass'y. 1. Do not touch the Pinch Roller. (Use gloves.)
2. Remove the S Reel and T Reel Ass'y. 2. When you install the Pinch Roller Ass'y, install as
3. Remove the 2 Polyslider Washers 1. shown in the circle. (Refer to Fig. 2-12-B)
NOTE
1. Take care not to damage the gears of the S Reel, T
Reel Ass'y and Idler Ass'y.
2. The Polyslider Washer may be remained on the back of
the reel.
3. Take care not to damage the shaft.
4. Do not touch the section "A" of S Reel and T Reel Ass'y.
(Use gloves.) (Refer to Fig. 2-11) Do not adhere the
stains on it. Fig. 2-12-B
5. When you install the reel, clean the shaft and oil it
(KYODO OIL Slidas #150). (If you do not oil, noise may
2-13: A/C HEAD (Refer to Fig. 2-13-A)
be heard in FF/REW mode.)
6. After installing the reel, adjust the height of the reel. 1. Remove the screw 1.
(Refer to MECHANICAL ADJUSTMENT) 2. Remove the A/C Head Base.
3. Remove the 3 screws 2.
4. Remove the A/C Head and A/C Head Spring.
S Reel
Idler Ass'y NOTE
1. Do not touch the A/C Head. (Use gloves.)
(A) T Reel Ass'y 2. When you install the A/C Head Spring, install as shown
in Fig. 2-13-B. (Refer to Fig. 2-13-B)
1
3. When you install the A/C Head, tighten the screw (1)
(A) first, then tighten the screw (2), finally tighten the screw
(3).
1
(1) (3)
2 2
2
Fig. 2-11 (2)
A/C Head
P5 Spring
2
Cassette Opener
Spring Position
Pinch Roller Ass'y Fig. 2-13-B
P5 Arm Ass'y
2-14: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-14)
Pinch Roller Lever
1. Remove the screw 1.
2. Remove the FE Head.
Main Chassis
1
FE Head
B2-3
DISASSEMBLY INSTRUCTIONS
2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y
1
(Refer to Fig. 2-15)
Middle Gear
1. Unlock the support 1 and remove the AHC Ass'y. E-Ring
2. Remove the 3 screws 2.
3. Remove the Cylinder Unit Ass'y. Main Cam
NOTE 2
Pinch Roller Cam
When you install the Cylinder Unit Ass'y, tighten the 3
screws from (1) to (3) in order while pulling the Ass'y Link Lever Spacer
Joint Gear
toward the left front direction. P5 Cam
2
(3)
AHC Ass'y
Fig. 2-17-A
Cylinder Unit Ass'y 1
2
(1) NOTE
2
(2)
When you install the Pinch Roller Cam, P5 Cam and Main
Cam, align each marker. (Refer to Fig. 2-17-B)
Fig. 2-17-B
Capstan Belt
Capstan DD Unit
2-18: CLUTCH ASS'Y (Refer to Fig. 2-18)
1. Remove the Polyslider Washer 1.
2. Remove the Clutch Ass'y, Ring Spring, Ring Clutch,
Gear Clutch and Polyslider Washer 2.
NOTE
When you install the Clutch Ass'y, oil the shaft (KYODO
OIL Slidas #150).
1 1
1 1
• Screw Torque: 5 ± 0.5kgf•cm Fig. 2-16
Clutch Ass'y
Fig. 2-18
B2-4
DISASSEMBLY INSTRUCTIONS
2-19: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-19-A) 2-20: INCLINED S/T ASS'Y (Refer to Fig. 2-20)
1. Remove the E-Ring 1 and remove the Main Loading 1. Unlock the support 1 and remove the P4 Cover.
Gear. 2. Remove the S-S Brake Spring.
2. Remove the Capstan Brake Spring. 3. Unlock the support 2 and remove the Loading Gear
3. Slide the Main Rod and remove the Capstan Brake Holder.
Arm Ass'y. 4. Remove the S-S Brake Arm.
4. Remove the Main Rod. 5. Remove the Inclined S.
5. Remove the Tension Lever. 6. Remove the Inclined T.
6. Unlock the 2 supports 2 and remove the Clutch Lever. 7. Remove the 2 screws 3, then remove the Guide Roller.
7. Remove the screw 3.
NOTE
8. Remove the LED Reflector.
9. Remove the Loading Arm S Ass'y and Loading Arm T Do not touch the roller of Guide Roller.
Ass'y.
10. Remove the Loading Gear S and Loading Gear T. Loading Gear Holder
11. Remove the Loading Gear Spring.
2
Guide Roller S-S Brake Spring
Capstan Brake Spring
Capstan Brake Arm Ass'y
S-S Brake Arm
1
3 Guide Roller
Main Loading Gear Inclined S
Main Rod
3
Tension Lever
Inclined T
Clutch Lever
Loading Gear T
1 P4 Cover
2 Loading Gear
3 Spring
2
Loading Arm T Ass'y
Fig. 2-19-A
NOTE
When you install the Loading Arm S Ass'y, Loading Arm T
Ass'y and Main Loading Gear, align each marker. (Refer
to Fig. 2-19-B)
Marker
Marker
Fig. 2-19-B
B2-5
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap amount of alcohol. (Refer to Fig. 3-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 3-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Fig. 3-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
CRT Screwdriver
Support
Alligator Clip
Fig. 3-1
Rubber Cap
Fig. 3-4
CRT
Support
Fig. 3-2
B3-1
DISASSEMBLY INSTRUCTIONS
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 3-5.
Support
CRT
Fig. 3-5
2
Wedge 1
(B)
(A)
Convergence •
Purity Magnet
Deflection Yoke
Wedge
Fig. 4-1
INSTALLATION
Install new Deflection Yoke in reverse steps of REMOVAL.
NOTE
After adjusting the purity and the convergence, fix the
screw 2 and lock the wedges.
B3-2
KEY TO ABBREVIATIONS
A A/C : Audio/Control H.SW : Head Switch
ACC : Automatic Color Control Hz : Hertz
AE : Audio Erase I IC : Integrated Circuit
AFC : Automatic Frequency Control IF : Intermediate Frequency
AFT : Automatic Fine Tuning IND : Indicator
AFT DET : Automatic Fine Tuning Detect INV : Inverter
AGC : Automatic Gain Control K KIL : Killer
AMP : Amplifier L L : Left
ANT : Antenna LED : Light Emitting Diode
A.PB : Audio Playback LIMIT AMP : Limiter Amplifier
APC : Automatic Phase Control LM, LDM : Loading Motor
ASS'Y : Assembly LP : Long Play
AT : All Time L.P.F : Low Pass Filter
AUTO : Automatic LUMI. : Luminance
A/V : Audio/Video M M : Motor
B BGP : Burst Gate Pulse MAX : Maximum
BOT : Beginning of Tape MINI : Minimum
BPF : Bandpass Filter MIX : Mixer, mixing
BRAKE SOL : Brake Solenoid MM : Monostable Multivibrator
BUFF : Buffer MOD : Modulator, Modulation
B/W : Black and White MPX : Multiplexer, Multiplex
C C : Capacitance, Collector MS SW : Mecha State Switch
CASE : Cassette N NC : Non Connection
CAP : Capstan NR : Noise Reduction
CARR : Carrier O OSC : Oscillator
CH : Channel OPE : Operation
CLK : Clock P PB : Playback
CLOCK (SY-SE) : Clock (Syscon to Servo) PB CTL : Playback Control
COMB : Combination, Comb Filter PB-C : Playback-Chrominance
CONV : Converter PB-Y : Playback-Luminance
CPM : Capstan Motor PCB : Printed Circuit Board
CTL : Control P. CON : Power Control
CYL : Cylinder PD : Phase Detector
CYL-M : Cylinder-Motor PG : Pulse Generator
CYL SENS : Cylinder-Sensor P-P : Peak-to Peak
D DATA (SY-CE) : Data (Syscon to Servo) R R : Right
dB : Decibel REC : Recording
DC : Direct Current REC-C : Recording-Chrominance
DD Unit : Direct Drive Motor Unit REC-Y : Recording-Luminance
DEMOD : Demodulator REEL BRK : Reel Brake
DET : Detector REEL S : Reel Sensor
DEV : Deviation REF : Reference
E E : Emitter REG : Regulated, Regulator
EF : Emitter Follower REW : Rewind
EMPH : Emphasis REV, RVS : Reverse
ENC : Encoder RF : Radio Frequency
ENV : Envelope RMC : Remote Control
EOT : End of Tape RY : Relay
EQ : Equalizer S S. CLK : Serial Clock
EXT : External S. COM : Sensor Common
F F : Fuse S. DATA : Serial Data
FBC : Feed Back Clamp SEG : Segment
FE : Full Erase SEL : Select, Selector
FF : Fast Forward, Flipflop SENS : Sensor
FG : Frequency Generator SER : Search Mode
FL SW : Front Loading Switch SI : Serial Input
FM : Frequency Modulation SIF : Sound Intermediate Frequency
FSC : Frequency Sub Carrier SO : Serial Output
FWD : Forward SOL : Solenoid
G GEN : Generator SP : Standard Play
GND : Ground STB : Serial Strobe
H H.P.F : High Pass Filter SW : Switch
C1-1
KEY TO ABBREVIATIONS
S SYNC : Synchronization
SYNC SEP : Sync Separator, Separation
T TR : Transistor
TRAC : Tracking
TRICK PB : Trick Playback
TP : Test Point
U UNREG : Unregulated
V V : Volt
VCO : Voltage Controlled Oscillator
VIF : Video Intermediate Frequency
VP : Vertical Pulse, Voltage Display
V.PB : Video Playback
VR : Variable Resistor
V.REC : Video Recording
VSF : Visual Search Fast Forward
VSR : Visual Search Rewind
VSS : Voltage Super Source
V-SYNC : Vertical-Synchronization
VT : Voltage Tuning
X X'TAL : Crystal
Y Y/C : Luminance/Chrominance
C1-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and
remocon key simultaneously.
The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug
AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor.
POWER ON total hours and PLAY/REC total hours are displayed on the screen.
Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION
OF USING HOURS).
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
Method Operations
Press the ATR button on the Adjusting of the Tracking to the center position.
remote control for more than Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL
2 seconds during PLAY. ADJUSTMENT" (PG SHIFTER).
C2-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
The following standard table depends on environmental conditions and usage. Unless maintenance is properly
carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts.
Also, long term storage or misuse may cause transformation and aging of rubber parts.
Capstan DD Unit
Loading Motor
Tension Band
Capstan Shaft
Tape Running Replace when rolling
Guide Post becomes abnormal.
Cylinder Unit Clean the Head
: Clean
: Replace
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
CLEANING
NOTE 2. TAPE RUNNING SYSTEM
After cleaning the heads with isopropyl alcohol, do not When cleaning the tape transport system, use the
run a tape until the heads dry completely. If the heads gauze moistened with isopropyl alcohol.
are not completely dry and alcohol gets on the tape, 3. CYLINDER
damage may occur.
Wrap a piece of chamois around your finger. Dip it in
1. AUDIO CONTROL HEAD isopropyl alcohol. Hold it to the cylinder head softly.
Wrap a piece of chamois around your finger. Dip it in Turn the cylinder head counterclockwise to clean it (in
isopropyl alcohol and clean the audio control head by the direction of the arrow). (Refer to the figure below.)
wiping it horizontally. Clean the full erase head in the NOTE
same manner. (Refer to the figure below.)
Do not exert force against the cylinder head. Do not move
the chamois upward or downward on the head.
Use the chamois one by one.
C3-2
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow
at least 30 minutes before Power On or alternatively, discharge backup capacitor. No need the setting for after INI 3F.
ADDRESS DATA ADDRESS DATA ADDRESS DATA ADDRESS DATA ADDRESS DATA ADDRESS DATA
00 10 0C 00 18 A3 24 00 30 04 3C 6C
01 1E 0D B3 19 89 25 5F 31 00 3D 2B
02 04 0E 35 1A 35 26 01 32 00 3E 21
03 6A 0F 66 1B 5F 27 F1 33 18 3F 15
04 00 10 FA 1C 05 28 01 34 00
05 00 11 40 1D F0 29 F0 35 00
06 00 12 80 1E 35 2A 0E 36 00
07 2F 13 40 1F F2 2B 00 37 00
08 40 14 00 20 00 2C 01 38 00
09 60 15 6A 21 00 2D 01 39 00
0A 02 16 00 22 00 2E 06 3A 00
0B 08 17 35 23 00 2F 01 3B 00
Table 1
INIT 00 83
POWER ON 0010
PLAY/REC 0003
Fig. 1
3. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the
ADDRESS until required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using SET + or - until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C4-1
SERVICING FIXTURES AND TOOLS
(For 2 head 1 speed model,
(For 2 head 2 speed model) JG002B Adapter JG005 Post Adjustment
4 head model)
VHS Alignment Tape JG002E Dial Torque Gauge Screwdriver
VHS Alignment Tape
JG001C (VP 2 S-LI6 3 ) (10~90gf•cm) Part No. SV-TG0-030-000
JG001E (VP 1 S-LI6 3 )
JG001D (VP 2 S-CO1 3 ) (small)
JG001F (VP 1 S-CO1 3 ) JG002F (60~600gf•cm)
JG001V (VP 2 S-X6 3 )
JG001R (VP 1 S-LI6 3 H)
JG001U (VP 1 S-X6 3 )
JG153 X Value Adjustment JG022 Master Plane JG024A Reel Disk Height JG100A Torque Tape
Screwdriver Adjustment Jig (VHT-063)
C5-1
PREPARATION FOR SERVICING
How to use the Servicing Fixture
1. Unplug the connector CP351, CP757, CP302 and CP403, then remove the TV/VCR Block from the set.
2. Unplug the connector CP810, CP820 and CP850, then remove the Main PCB from the VCR Block.
3. Connect as shown in the below figure using the Service Fixture.
• Connect the Syscon PCB to the Main PCB with the cable JG162C and JG162D.
• Connect the Syscon PCB to the CRT PCB with the cable JG162Y.
4. Remove the Operation PCB from the set, then connect it with the Syscon PCB.
If necessary, connect CP351 (Front A/V Jack Input Terminal)
5. Short circuit between TP1001 and Ground with the cable JG154.
(Refer to MAJOR COMPONENTS LOCATION GUIDE)
The EOT, BOT and Reel Sensor do not work at this moment.
6. At that time, the STOP/EJECT button is available to insert and eject the Cassette Tape.
Front Cabinet
CRT PCB
CP820
CP850
Main PCB
JG162Y CP810
JG162D
CD850
JG162C
CD820
Syscon PCB
CD810
TP1001
CP757
CD757
Operation PCB
JG154
To Ground
CD351
C5-2
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION
POST POSITION
Read the following NOTES before starting work.
1. Set to the PLAY mode.
• Place an object which weighs between 450g~500g on 2. Adjust the Tension Adjust until the edge of the Tension
the Cassette Tape to keep it steady when you want to Arm is positioning within 0.5mm range from the
make the tape run without the Cassette Holder. (Do not standard line center of Main Chassis.
place an object which weighs over 500g.) After this adjustment, confirm that the cut position is
• When you activate the deck without the Cassette located in "A" area as shown in Fig. 1-2-B. If it is
Holder, short circuit between TP1001 and TP1002. (Refer located in "B" area, adjust again.
to ELECTRICAL ADJUSTMENT PARTS LOCATION 3. While turning the S Reel clockwise, confirm that the
GUIDE) In this condition the BOT/EOT/Reel Sensor will edge of the Tension Arm is located in the position
not function. described above.
1-1: CONFIRMATION AND ADJUSTMENT OF REEL
DISK HEIGHT Standard line of Main Chassis
(A)
Reel Disk Height Adjustment Jig Cut Position
(JG024A)
(B)
Tension Adjust
Fig. 1-2-B
(A) Tentelometer
Height Adjustment
Washer Video Tape
2.6x4.7xT0.13
2.6X4.7xT0.25 Fig. 1-1-B
D1-1
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE 2. CONFIRMATION AND ADJUSTMENT
1. Operate within 4~5 seconds after the reel disk begins to OF TAPE RUNNING MECHANISM
turn.
Tape Running Mechanism is adjusted precisely at the
2. Install the Torque Gauge (JG002F) and Adapter (JG002B)
factory. Adjustment is not necessary as usual. When you
on the S Reel. Set to the Rewind mode. (Refer to Fig.1-4)
replace the parts of the tape running mechanism because
3. Then, confirm that it indicates 120~180gf•cm.
of long term usage or failure, the confirmation and
NOTE adjustment are necessary.
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk. 2-1: GUIDE ROLLER
1. Playback the VHS Alignment Tape (JG001C or JG001E).
1-5: CONFIRMATION OF REEL BRAKE TORQUE (Refer to SERVICING FIXTURE AND TOOLS)
(S Reel Brake) (Refer to Fig. 1-4) 2. Connect CH-1 of the oscilloscope to TP4002 (Envelope)
and CH-2 to TP4001 (SW Pulse).
1. Set to the STOP mode. 3. Press and hold the TRACKING-AUTO button on the
2. Move the Idler Ass'y from the S Reel. remote control more than 2 seconds to set tracking to
3. Install the Torque Gauge (JG002F) and Adapter center.
(JG002B) on the S Reel. Turn the Torque Gauge 4. Trigger with SW Pulse and observe the envelope. (Refer
(JG002F) clockwise. to Fig. 2-1-A)
4. Then, confirm that it indicates 70~100gf•cm. 5. When observing the envelope, adjust the Adjusting Driver
(T Reel Brake) (Refer to Fig. 1-4) (JG005) slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
1. Set to the STOP mode. flatness is not moved so much.
2. Move the Idler Ass'y from the T Reel Ass'y. 6. Adjust so that the A : B ratio is better than 3 : 2 as shown
3. Install the Torque Gauge (JG002E) and Adapter in Fig. 2-1-B, even if you press the Tracking Button to
(JG002B) on the T reel. Turn the Torque Gauge move the envelope (The envelope waveform will begin to
(JG002E) counterclockwise. decrease when you press the Tracking Button).
4. Then, confirm that it indicates 35~60gf•cm. 7. Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
Torque Gauge/Adapter
(JG002F/JG002B) NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
Torque Gauge/Adapter
(JG002E/JG002B) CH-1
Envelope
(TP4002)
CH-1 CH-2
Track Track
CH-2
SW Pulse (TP4001)
S Reel
Envelope
A:B=3:2
Fig. 2-1-B
D1-2
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ 2-3: TAPE RUNNING ADJUSTMENT
CONTROL HEAD (X VALUE ADJUSTMENT)
When the Tape Running Mechanism does not work well, 1. Confirm and adjust the height of the Reel Disk.
adjust the following items. (Refer to item 1-1)
2. Confirm and adjust the position of the Tension Post.
1. Playback the VHS Alignment Tape (JG001C or JG001E).
(Refer to item 1-2)
(Refer to SERVICING FIXTURE AND TOOLS)
3. Adjust the Guide Roller. (Refer to item 2-1)
2. Confirm that the reflected picture of stamp mark is
4. Confirm and adjust the Audio/Control Head.
appeared on the tape prior to P4 Post as shown in Fig. 2-
(Refer to item 2-2)
2-A.
5. Connect CH-1 of the oscilloscope to TP4002, CH-2 to
a) When the reflected picture is distorted, turn the screw
TP4001 and CH-3 to HOT side of Audio Out Jack.
1 clockwise until the distortion is disappeared.
6. Playback the VHS Alignment Tape (JG001U or JG001V).
b) When the reflected picture is not distorted, turn the
(Refer to SERVICING FIXTURE AND TOOLS)
screw 1 counterclockwise until little distortion is
7. Press and hold the TRACKING-AUTO button on the
appeared, then adjust the a).
remote control more than 2 seconds to set tracking to
3. Turn the screw 2 to set the audio level to maximum.
center.
4. Confirm that the bottom of the Audio/ Control Head and
8. Set the X Value adjustment driver (JG153) to the 4 of
the bottom of the tape is shown in Fig. 2-2-C.
Fig. 2-2-B. Adjust X value so that the envelope waveform
c) When the height is not correct, turn the screw 3 to
output becomes maximum. Check if the relation between
adjust the height. Then, adjust the 1~3 again.
Audio and Envelope waveform becomes (1) or (2) of Fig.
2-1-A.
Audio/Control Head
2
4
Fig. 2-2-B
Audio/Control Head
Tape
0.25±0.05mm
Fig. 2-2-C
D1-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
3
7
2
1
8
12 11 10 9
D1-4
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the CH-2
circuits or replacing electrical parts or PCB assemblies.
CAUTION
When replacing IC's or transistors, use only specified 6.5H
silicon grease (YG6260M).
(To prevent the damage to IC's and transistors.) CH-1
Fig. 2-1-A
On-Screen Display Adjustment
1. Unplug the AC plug for more than 30 minutes to set the
clock to the non-setting state. Then, set the volume level
to minimum. CH-2
2. Press the VOL. DOWN button on the set and the channel
button (9) on the remote control simultaneously to display
adjustment mode on the screen as shown in Fig. 1-1.
CH-1
NOTE 6.5H
Use the channel buttons (1-8) on the remote control to Fig. 2-1-B
select the options shown in Fig. 1-1.
Press the channel button (0) on the remote control to 2-2: RF AGC DELAY
end the adjustments.
1. Receive the monoscope pattern.
2. Connect the digital voltmeter between the pin 5 of
1. H/V CP603 and the pin 1 (GND) of CP603.
2. AKB 3. Activate the adjustment mode display of Fig. 1-1 and
3. COLOR TEMP press the channel button (5) on the remote control.
4. PICTURE The Fig. 2-2 appears on the display.
5. OTHERS 4. Press the channel button (1) on the remote control to
6. TEST PATTERN select "RF AGC DELAY".
7. STEREO/SAP 5. Press the VOL. UP/DOWN button on the remote control
8. (VOL TEST) 0. END until the digital voltmeter is 2.50 ± 0.05V (80dB).
Fig. 1-1
1. RF AGC DELAY
2. BASIC ADJUSTMENTS 2. VIDEO LEVEL
3. FM LEVEL
(VCR SECTION) 4. OSD H
2-1: PG SHIFTER 5. CUT OFF
6.
1. Connect CH-1 on the oscilloscope to TP4001 and CH-2
7.
to TP4501.
8. 0. RETURN
2. Playback the alignment tape. (JG001C) Fig. 2-2
3. Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
4. Press the VOL. DOWN button on the set and the 2-3: VCO FREERUN
channel button (3) on the remote control simultaneously 1. Connect the oscillator to pin 11 of TU601.
until the indicator REC disappears. If the indicator REC 2. Connect the digital voltmeter to pin 47 of IC601.
disappears, adjustment is completed. 3. Adjust the L608 until the digital voltmeter is 3.6 ± 0.05V.
(If the above adjustments doesn't work well:)
(TV SECTION)
5. Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously 2-4: CONSTANT VOLTAGE (AC)
until the indicator REC disappears. 1. Using the remote control, set the brightness and
6. When the REC indicator is blinking, press both VOL. contrast to normal position.
DOWN button on the set and the channel button (4) on 2. Connect the digital voltmeter to TP401.
the remote control simultaneously and adjust the 3. Set condition is AV MODE without signal.
Tracking +/- button until the arising to the down of Head 4. Adjust the VR502 until the DC voltage is DC 130 ± 0.5V.
Switching Pulse becomes 6.5 ± 0.5H.
(Refer to Fig. 2-1-A, B) 2-5: CONSTANT VOLTAGE (DC)
7. Press the Tracking Auto button.
1. Using the remote control, set the brightness and
contrast to normal position.
2. Connect the digital voltmeter to TP401.
3. Set condition is AV MODE without signal.
4. Adjust the VR501 until the DC voltage is DC 130 ± 0.5V.
D2-1
ELECTRICAL ADJUSTMENTS
2-6: CUT OFF 2-9: SUB BRIGHTNESS
1. Place the set with Aging Test for more than 15 minutes. 1. Receive the monoscope pattern. (RF Input)
2. Set condition is AV MODE without signal. 2. Using the remote control, set the brightness and
3. Using the remote control, set the brightness and contrast to normal position.
contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and
4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control.
press the channel button (5) on the remote control. The Fig. 2-4 appears on the display.
The Fig. 2-2 appears on the display. 4. Press the channel button (1) on the remote control to
5. Press the channel button (5) on the remote control to select "BRIGHT".
select "CUT OFF". 5. Press the VOL. UP/DOWN button on the remote control
6. Adjust the Screen Volume until a dim raster is obtained. until the white 25% is starting to be visible.
6. Receive the monoscope pattern. (Audio Video Input)
2-7: FOCUS 7. Press the AV button on the remote control to set to the
1. Receive the monoscope pattern. AV mode. Then perform the above adjustments 2~5.
2. Using the remote control, set the brightness and
contrast to normal position. 1. BRIGHT
3. Turn the Focus Volume fully counterclockwise once. 2. CONTRAST
4. Adjust the Focus Volume until picture is distinct. 3. COLOR
4. TINT
2-8: WHITE BALANCE 5. SHARPNESS
NOTE: Adjust after performing CUT OFF adjustments. 6. OSD CONT
7.
1. Place the set with Aging Test for more than 15 minutes. 8. 0. RETURN
2. Receive the white 100% signal from the Pattern Fig. 2-4
Generator.
3. Using the remote control, set the brightness and contrast 2-10: SUB COLOR
to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and 1. Receive the color bar pattern. (RF Input)
press the channel button (2) on the remote control to 2. Connect the synchro scope to TP801.
select "AKB". The Fig. 2-3 appears on the display. 3. Using the remote control, set the brightness, contrast
5. Press the channel button (2) on the remote control to and color to normal position.
select the "R.BIAS". 4. Activate the adjustment mode display of Fig. 1-1 and
6. Using the SET +/- keys on the remote control, adjust the press the channel button (4) on the remote control.
R.BIAS. The Fig. 2-4 appears on the display.
7. Press the CH. UP/DOWN button on the remote control to 5. Press the channel button (3) on the remote control to
select the "G.BIAS", "B.BIAS", "R.DRIVE" or "B.DRIVE". select "COLOR".
8. Using the SET +/- keys on the remote control, adjust the 6. Adjust the VOLTS RANGE VARIABLE knob of the
G.BIAS, B.BIAS, R.DRIVE or B.DRIVE. oscilloscope until the range between white 100% and 0%
9. Perform the above adjustment 7 and 8 until the white is set to 4 divisions on the screen of the oscilloscope.
color is looked like a white. 7. Press the VOL. UP/DOWN button on the remote control
until the red level is set to the 4 divisions.
(Refer to Fig. 2-5)
1. AKB AUTO 8. Receive the rainbow pattern. (Audio Video Input)
2. R. BIAS 9. Press the AV button on the remote control to set to the
3. G. BIAS AV mode. Then perform the above adjustments 2~7.
4. B. BIAS
5. R. DRIVE
6. G. DRIVE
7. B. DRIVE
8. AGC AUTO 0. RETURN 0%
Fig. 2-3
100%
100%
Fig. 2-5
D2-2
ELECTRICAL ADJUSTMENTS
2-11: HORIZONTAL PHASE 2-15: OSD HORIZONTAL
1. Receive the monoscope pattern. 1. Receive monoscope pattern.
2. Using the remote control, set the brightness and 2. Using the remote control, set the brightness and
contrast to normal position. contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (1) on the remote control. press the channel button (5) on the remote control.
The Fig. 2-6 appears on the display. The Fig. 2-2 appears on the display.
4. Press the channel button (1) on the remote control to 4. Press the channel button (4) on the remote control to
select "H. PHASE". select "OSD H".
5. Press the VOL. UP/DOWN button on the remote control 5. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and until the difference of A and B becomes minimum.
left becomes minimum. (Refer to Fig. 2-7)
1. H. PHASE
2. H. BLK [ TV ]
3. V. SIZE
4. V. POSI
5. V. LIN
6. V. SC
7. V. COMP OSD H
8. (H FREQ) 0. RETURN
Fig. 2-6
A B Fig. 2-7
2-12: VERTICAL SIZE
1. Receive the monoscope pattern. 2-16: VERTICAL LINEARITY 60 (AV)
2. Using the remote control, set the brightness and
contrast to normal position. 1. Receive the monoscope pattern (Audio Video Input).
3. Activate the adjustment mode display of Fig. 1-1 and 2. Using the remote control, set the brightness and
press the channel button (1) on the remote control. contrast to normal position.
The Fig. 2-6 appears on the display. 3. Activate the adjustment mode display of Fig. 1-1 and
4. Press the channel button (3) on the remote control to press the channel button (1) on the remote control.
select "V. SIZE". The Fig. 2-6 appears on the display.
5. Press the VOL. UP/DOWN button on the remote control 4. Press the channel button (5) on the remote control to
until the horizontal over scan is equal to the vertical over select "V. LIN".
scan. 5. Press the VOL. UP/DOWN button on the remote control
until the horizontal line of the colour bar comes to
2-13: VERTICAL LINEARITY approximate center of the CRT.
D2-3
ELECTRICAL ADJUSTMENTS
3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE
(VCR SECTION)
TP1001
TP4002
TP4001
IC601
TU601
L608
J4501
CP603
TP4501
SYSCON PCB
D2-4
ELECTRICAL ADJUSTMENTS
(TV SECTION)
CRT PCB
FOCUS VOLUME
SCREEN VOLUME
MAIN PCB
D2-5
ELECTRICAL ADJUSTMENTS
4. PURITY AND CONVERGENCE 4-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 4-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch
terrestrial magnetism. pattern on the center of the screen by adjusting the pair
3. Turn ON the unit and demagnetize with a Degauss Coil. of 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 4-1) 4-4: DYNAMIC CONVERGENCE
If the deflection yoke and magnet are in one body,
NOTE
untighten the screw for the body.
2. Receive the green raster pattern from the color bar Adjust after performing adjustments in section 4-3.
generator. 1. Adjust the differences around the screen by moving the
3. Slide the deflection yoke until it touches the funnel side deflection yoke upward/downward and right/left.
of the CRT. (Refer to Fig. 4-2-a)
4. Adjust center of screen to green, with red and blue on 2. Insert three wedges between the deflection yoke and
the sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 4-2-b)
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch RGB RGB
pattern on the center of the screen by adjusting the pair
of 4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the R
pair of 6 pole magnets. G
8. Adjust the crosshatch pattern to change to white by B
R
repeating steps 6 and 7. G
B
4-2: PURITY
UPWARD/DOWNWARD RIGHT/LEFT SLANT
NOTE SLANT
Adjust after performing adjustments in section 4-1. Fig. 4-2-a
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue color.
5. Adjust the slant of the deflection yoke while watching
the screen, then tighten the fixing screw. WEDGE
DEFLECTION YOKE
DEFLECTION YOKE SCREW WEDGE POSITION
MAGNET SCREW Fig. 4-2-b
6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS
Fig. 4-1
D2-6
F-5
C4215
W817
C4230
R4210 R4223 R4222
W805 R4221
C664 R4206
R420
Q4210
R636
W807
C640
R4225 R4205
W825
Q4202
Q4205
W804
C4205
R403
R4030
R4220
R4208
C413
R4239
Q4207
R656
C604
R678
C655
R645
C609
R638
C618
C639
R634
R637
R640
R641 C607
R607
0
C644 R608
R618
C647 C612
C675 W862
C605
R639 R679 C654
C614 W905
R648
W837
C646
R642 C615
R616
W836
R604
C601
R646
W066 C677
C621
C656
W802
R619
Q608
W067 R603
R630 C660
R657
R613 C620
R628 C623 R658
R629 R621
W801
R622
W893
Q403
Q601
Q611
W889
R4020
R665
R4003 C4101
R4001
C4002
R4054
C4023
R4067
Q4018
C4025
R4053
R4038
R4008
Q4007
R4052
C4102
R4069 R4055
R4014
C4032
R4063 C4107
R4017
C4033
C4004
C4026
R4015
C4037
R4016
R1071
C4019
W911 C4028
W318
C4016 C4014
C4020
R4027
C4043
R4032
1
R4057
W109
Q351
R4005 W309
C361
C4010
R4023
C4035
C4018
C4070
R353
C4006
C4047
C4038
81
IC
R361
R4022
C1009 40
R4031 C4044
R4013
R4004 C4007
01
C4053
31
SOLDER SIDE
R359
C359
C4206
R426 C362
R352
R4012
R4011 C4013
C4048
C4068
C4005
R4026 R4065
C4042
C1007
C4054
Q4003
51
R4002 R4056
C4046
R4058
R4033
C4062
C4123
C4060
R1008
C4052 R4073
C4083 R4034
C4056
C4059
R4051 C4064
R1070
PRINTED CIRCUIT BOARDS
C4061
C4075
C4089
R1029
C4076
R4050 C4067
C1062 C4100 R4042
C4080
C4115
C4099 C4063
Q4006
R4035 R1015
W871
C1022
Q4015
C4082
C4086
R1069
W196
R1011
C4116
C1015
C1012
C1074
R4077
C1001
R1090
R1039
C1004
Q1004
C1092
C1063
R1057
C1006
C4121R4074
C1073
SYSCON/CRT/POWER SW. (CHIP MOUNTED PARTS)
C1033 C4122
R1053
R1009
C1028
C1026
W869
C1082
C1031
85
R1012
C1020
R1054
C1081 W222
C1024
C1025
R1033
C1023
C1008 R1064
W868
R1067 IC
C1002
R1058
Q1002
10
1
57
R1024
06
R4209 C1019
C1067
R1017
C1060
R1027 C1018
R1007
C1010
R1020 R355
R1010
W828 R1022
29
Q4203
R1021 C1038
Q1010
C1035
C1040
C1078
R1030
R1013
R1003
R1063
Q1015
C1017
C1056
R1087
C1050
R1083
R1050
C1044
Q1016
R1062
C805
C1055
IC1003
R1006
R1045 R1044 R1078
R816
R1096
C811
R813
R1080 R812
C1071
C822
C821
R814
R1031 C1014 R815
R1049
R1051
C4203
C4217
F-6
A B C D E F G H
ENV_DET
D_V_SYNC
P.CON+5V_A
H.SW
P.CON+9V
SDA
SCL
8 (SYSCON PCB) L4002 8
L4013
100uH
1/2W
100uH
220
R4075 R4042
R4041
0305
9
10M 10M BUFFER
2 Y/C_V
R4065 Q4006
C4121 0.1 B
C4122 0.1 B
TP4002
10V 100 KA
6.3V 47 KA
NC 2SA1037AK 3.1
1B
C4069
C4084
1K
C4063
C4089
0.1 B
V.ENV
C4123
0.1 B
FROM/TO POWER W871 2.5
0
P.CON+5V_A
GND
10V 470 YK
AMP
C4033
C4076
B
0.1 B
S104Y
50V4.7 KA
0.022 B
0.0018
Q4007
C4108
C4107
C4040
C4050
0.47 B
R4026 0.039 B C4042
C4046
0.068 B
2SC2412K R4055
Y/C_A
1.4
R4052
680
C4038
7 6.3 7
1.2K
1 B
L4008 2.0
C4059 50V4.7 KA
R4053 R4054
C4054
3P CH
18P CH
C4064
0.01 B
C4072
C4099
0.022 B
0.1 B
C4035
C4057
C4048
B
1mH 560K 330K
27K
R4022
P.CON+9V 0.01 B FROM/TO CHROMA I/F
C4061 0.022
560
0.001 B
W984
W985
39uH
L4016
L4011
R4034 12uH
0.01 B
C4101
0.1 B
C4067
TUNER_V
4.433619MHz
FROM/TO CYL/MOTOR
R4050 330
R4001 TUNER_A_YC
X4001
0.01 B
4.7K
C4075
CP4001_1 Y/C_V
1.5K C4010 Y/C/AUDIO/CCD/HEAD AMP
TOC-C04X-B1
C4002 NC Y/C_A
IC4001
4 SP-CH1 (R) 0.001 B
TP4001
H.SW
HA118217F NC NC
3 SP COM 0.056 B 0 2.1 2.8 4.5 2.6 2.1 1.0 1.7 2.2 2.7 2.8 0 4.8 4.8 2.4 0 4.8 4.8 4.8 2.1 2.9 3.0 0.1 2.8 2.1 2.0 2.8 2.5 0.4
15.6KHZ TRAP 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
2 SP-CH2 (L) 10 8
L4001 2.5 C GND DO KIL CVCC NTSC/PAL C.SYNC
81
50
1 NC 2623003 VCA
N-P CONT
FROM/TO 21PIN I/O
X TAL VCO/OSD CR DET 2FSC SERIAL CONT 0.4
6 C4018 0.033 B 1.2 INTERFACE OUT 6dB AMP 6dB AMP
6
NC LIMITTER HEAD SW1 LEVEL DET1
82
49
2FSCVCO FH SYNC
HEAD SW2 TANC P CCD REAR_V_IN
C4024 - LPF C SQUELCH SYNC.SEP. 0
3
2
1
2.6 KILLER
C4004 REAR_A_IN_L
83
48
DET OUT SW26R LEVEL DET2
C4014 0.1 B ME
COLOR
SW25 0
50V3.3 KA 1.5 COMP DET PB/REC REC REC PB KILLER
0.01 B R
84
47
ENV SECAM DISCRI AFC APC APC ID DET DL +
DET HPF
6
DET PULSE
0 GEN CLEAR SYNC 0
R4003
85
46
330
NC HA GND DET
C.K LMIT 0
C4019 0.01 B 1/2 DOWN 1/2 ACC APC DELAY CLPH
2.2 + SP2 CONV. DET SW CLPH WHAITH CCD
86
45
2FL VCO PHASE SW P SW24 N P SQUELCH
SW32 SP2 GND 0
C4020 0.01 B - R MAIN C4080
2.2 4PHASE GEN
87
44
CONV2 FEED BACK
SW33 MAIN + B.D 2.5
C4027 0.01 B SP1 SW30 SW28 CONV1 SW22 CLAMP 0.01 B FROM/TO MICON
2.1 - CH2 SW29
88
43
P SW20 SW23 R P VIDEO ALC
0.01 B
SP CTL TRAP 4.8
C4083
SW34 2M LPF P R
C4028 0.01 B + ACC HPF VCR_A_MUTE
2.2 P SW21
89
42
CH1 R FHTRAP
L4004 C4015 6.3V 47 KA SW35 SP1 EP SEP R BPF 1.8 H.SW
P.CON+5V_A 4.8 HPF
90
41
HA VCC VCA L SECAM COMP SW19 CLOCK C.SYNC
C4016 0.1 B 4.8
100uH 0305 SW27 DEIVER
6.3V 47 KA
EP2
5 0 + MIX SCL 5
91
40
SW31 LEVEL C.K B.E SW18
TO F/E HEAD C4097 P 4.8
C4088
SW36 EP2 CH2 L SECAM
- REC LPF ADJ TRAP SDA
0.01 B 0 C Y
92
39
CP4004 TMC-T02X-E1 MUTE + R
SW37
P SW7
CCD CCD 3.0 D_V_SYNC
2 FE HEAD(GND) 0 EP1
-
CH1 629 FM P S SQPB
P SW17
93
38
FROM TRAP AGC EQ DL G V.REC_ST_H
C4098 SW38 EP1 R EQ DO EDGE Y APA 4.8
1 FE HEAD(HOT) + MESECAM
0.01 B 0 DET SQPB DET DELAY MODE ENV_DET
94
37
DET SW16 R
W5RH3.5X5X1.0
95
36
+ N.C. VCC=5V
DEMO EMPH DE EMPH AGC DEL 4.8 CTL-
B4001
D4001 1B DET
SW4 SW5 P C4082 100uH
4.8 7M HPF PB ALC
96
35
FROM/TO A/C HEAD AVCC
P SW2
9A06B MESECAM_M
CD4005 SB10-03A3 SUB LPF FBC/ALC 3.0 180P CH
MESECAM_M 0 PRE R LAG LERD VIDEO AGC SW115
1.25X6X138XC CP4005 IMSA-9604S-06Z14 1 VV_H
SW1EP ON
97
34
LPF SW10 SW14
AMP VCA YNR CH3 CH1
MAIN MAIN REC 0
1 AE HEAD(+) 4.8 DE EMPH P DO DO
CH2
98
33
SW40
REC ON
FM MOD EMPH R P R
SP ON
SW3
CARRIER
75
2 AE HEAD(-) 0
R4074
R4008 OFFSET ATT ATT ATT
CTL- VCR_A_MUTE 2.5 Y LPF SW12
100 99
32
MUTE FO/DEV W.C/DC SW15 CLAMP (-10dB) (-10dB) (-10dB)
3 CTL- SW9 R P
L4024 ADJ 0 C4086
CTL+ 1K 2.5 REC EQ BAND SW6 S-DET REAR_V_IN
4 CTL+
31
CLAMP LPF
4 A.GND GAP 3 2 1 YVCC
SW11 P R YGND AGC 2.8 4
0.01 B
5 AUDIO REC 10uH 1B
7
6.3V 220 YK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
6 AUDIO PB
C4017
2.5 2.5 0 2.5 0 2.9 2.5 2.5 2.5 2.5 2.5 4.8 1.4 1.4 3.1 0.7 0.6 2.1 3.1 2.7 2.4 2.1 3.1 2.1 1.4 2.1 0 2.8 1.9 2.8 FROM/TO DEFLECTION
R4014
270K
10M
560
R4063
L4025
R4069
NC NC NC
50V 4.7 KA
L4026 10uH
0.1 B
0.1 B
C4026
C4062
C4070
3 C4074
50V 4.7 KA
C4051 6.3V 22 KA
C4039
R4015 R4049
C4041
VD
C4049
10uH
0.1 B
2.2M
R4032
C4056
6.8K
R4038
16V 10 KA
C4023
C4071
0.1 B
10K 16V 10 KA
47P CH
C4115
390K BUFFER R4057
16V 10 KA
R4016
680P CH
C4077
C4037
W911 C4060
50V4.7 KA 180
C4047
Q4018 W827 TUNER_V
1 B
2SC2412K 3.7 39K +-1%
C4052 150P CH
0.1 B
C4100 27P CH
R4020 50V 2.2 KA
47P CH
VD
C4058
4
47K +-1%
C4031
1B
820P CH
R4030 6.8K
5
R4017
10M 1.5
C4032
1.0
R4023 PB SW
C4043
16V10 KA
Q4015
R4035
C4116
3.3K
KA
C4036
10K KRC104SRTK
3 3
R4031
1B 2.3
R4051 10K
C4073
4.7K
390
0.1 B
R4067
50V1 KA
C4068
50V1
0 VV_H
3.9M
R4077
220uH
L4012
C4078
0
0.0047 B
R4021
C4102
C4055 0.1 B
18K +-1%
6.3V 47 KA
R4073
1M
C4001
C4013
R4002 4.6 6.3V 33 KA 220P CH R4011
4.9
100uH 9A06B
1 6
0.01 B
C4007
L4009
NORMAL AUDIO 2 5 V.REC ST SW
100V 0.022 MKT
4.9 OSC
REC ST SW Q4002 3 4 Q4003
0
Q4001 KTC3203_Y KRA103SRTK R4012
R4027
0.7
C4009
R4005
27K
KTC3203_Y
L4003 150
2 2
100uH 9A06B
2.2K
0 C4006 KTC3198
P.CON+5V_A
0
R4013
0.0047 B
P.CON+5V_A
V.REC_ST_H
P.CON+5V_A
0.01 B
4.7K 0.7
C4005
REAR_A_IN_L
TUNER_A_YC
PB SW 0
Q4005
KTC3198
PCB010
W941
VMA230
NOTE: THE DC VOLTAGE AT EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR
1 MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1
DURING PLAYBACK
A B C D E F G H
G-1 G-2
A B C D E F G H
R1045
8 8
R1044
R1003
3.3K
R1077
1/4W
3.3K
22K
10K
(SYSCON PCB)
LDM_CTL
SDA
R1096
RESET
SCL
CAP_LIMIT
SCL
IIC_OFF
SDA
C1082
0.1 B
C1024 15P CH
22K
R1031
1K
12P CH
C1072 C1030
C1025
S-24C08ADPA-01 68P CH
C1071
18P CH
18P CH
C1023
0.1 B
68P CH 0.1 F
C1026
C1028
22K 1/4W
4.3 4.7 0 5.1
C1004 0.1 B
D1006
22K
R1033
5 6 7 8
R1023
11
SB140-EIC X1001
VCC
FROM/TO POWER
TEST
SDA
SCL
D1010
EEP ROM IC
AT+5.6V 10MHz
SB140-EIC
32.768KHz
GND
X1002
C1060
VSS
A2
A1
A0
7 POWER_FAIL[DC] 7
0.1 B
12
IC1099
VCR_POWER_H 4 3 2 1
P.CON+5V_A 2.2 5.2 5.2 3.3 2.6 0 2.5 5.2 1.5 1.6 0 NC NC NC NC NC NC NC NC 0 NC NC 3.6 3.6 NC NC 5.2 0 0 0 0 0
AT+5V C1047 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57
MS_SENS_CTL
DEC_TU_SW
LDM_CTL
MDO
R1024
VSS
CAP_LIMIT
FWE
NC
NC
NC
NC
NC
NC
NC
OSC2
OSC1
PAL-H
P21/SO1
IIC_DATA_0
VCL
IIC_OFF
P.CON+5V VOL_CTL 5.2
/RES
VSS
X1
X2
TRICK PB H
IIC_CLK_0
P20/SI1
16V 10 KA
85
55 56
AT+12V 15K R1001 5.2
CYL_DRIVE 2.5 TU_AUDIO_MUTE_H
86
MOTOR_GND
R1066 1M 1/4W
CONTROL_IN 2.5 85 VOLUME_PWM R1015 22K EXT_IN_L FROM/TO 21PIN I/O
87
54
CAP_FULL EXT_IN-L
1K 1/4W 3.1
CAP_F/R 0 TV_A_MUTE
88
53
CAP_FWD-L 86 CYL_SPEED_UP 56 VCC TV_MUTE KEY_B
5.3
FROM/TO Y/C/A/H.AMP VV_H 5.2 CENT_LED_CTL KEY_A
89
52
VV-H 55 TUNER MUTE CENT LED
5.2
VCR_A_MUTE 0 T-REC_LED
MESECAM_M NC
90
51
VCR_MUTE TEXT RESET R1010 4.7K
D_V_SYNC 5.2 REC_LED
C1063 W892 OSD_Y V.REC_ST_H 0 TAB_SW
6 6
91
50
V.REC_ST_H V.REC.START-H TAB_SW STANDBY_H
5.2
R1053
VV_H 220P CH SPOT_OFF 0 REMOCON_IN
92
49
1K
PROTECT ON_TIMER_LED NC
SCL
TV_POWER_H 5.2 REC_LED EXT_IN_L
C1074
93
48
SDA TV_POWER_ON-H REC/OTR_LED
0 TU_AUDIO_MUTE_H
H.SW TUNER_ON/OFF 0 T-REC_LED
0.01 B
94
47
DA RGB SW T-REC_LED TUNER_ON/OFF
ENV_DET 5.2
R1090 5.2
VCR_A_MUTE VCR_POWER_H AT+5V
95
46
VCR_POWER_ON-H OTPB_LED NC
CTL+ 22K 0 STANDBY_H
96
45
CTL- D1004 YC0 STAND BY
C1069
C1011
C.SYNC
R1068
6.3V 33
97
44
1SS133 NC BB L DEGAUSS
22K
1/4W
BOT NC
KA
R1082 22P CH
H_CTL SYSCON/TIMER/SERVO IC REMOCON_IN
98
43
R1039 H CONTROL REMOCON IN
BOT SENSOR IC1006 4.7 R1035
22K 1/4W
Q1017 OSDR 0 OEC0107B
112 111 110 109 108 107 106 105 104 103 102 101 100 99
42
22K R CFG_IN2
ST-304L 5.2 22K
C1073 OSDG 0 SERVICE
41
5 G SERVICE NC 5
0.001 B
5.3 TP1001
C1006
0.001 B
40
B REEL-T
C1092
EOT SENSOR
5.1
5.1 Q1006 5.1 FF/REW-L 5.2 REEL-S C1001
39
FF/REW-L REEL-S
ST-304L 5.1
R1004 10K 1/4W 0 D1001 RB721Q C.SYNC 220P CH
38
DPG SYNC IN
LNA2702L010R
0.2 0.1
15 R1008 5.3 R1069 5.6K
2.2
D1003
CYL_FG/PG R1065
37
EOT DFG/DPG POWER_FAIL VD FROM/TO CHROMA/IF
C1007 1K R1014 4.9 C1043
H.SW 2.6 33K 1/4W
36
VIDEO_H.SW AVCC
0.0047 B 1K 1/4W 5.2 0.1 B C1044 SPOT_OFF
R1057 R1055 BOT
CYL_DRIVE
35
NC HIFI_H.SW BOT SDA
R1011
220K
270
2.3
6.3V 100 KA
R1058
34
DRUM_PWM 111 C.SYNC KEY_B
C1093
R1062
0.18 B R1067 56K 14 2.6 30 TUNER AGC IIC_OFF
CONTROL_IN KEY_A
33
CAP_PWM KEY_A
330K
112 VCC
R1032
56K 0 29 MESECAM_M 18
D_V_SYNC MS_SEN-B R1059 R1013
C1002
32
CENT LED SW DUMMY.V.SYNC MSSEN_B H.SYNC 4.7 0
4 Q1002 0
0
VD SW 4
MS_SEN-A 1K 10K
31
KRC103SRTK VSS MSSEN_A V.SYNC Q1015
AFT.S.CURVE
0.6
VODEO_ENV
0.2
CTLAMP(0)
4/2FSCOUT
C1067 0.4 2SC2412K
CTLSMT(I)
C.SYNC AGC_M
30
4/2FSCIN
4.2
CTLBIAS
OSDVCC
OSDVSS
CENT_LED_CTL 17
AFCOSC
HIFI ENV
CTLREF
AFCLPF
HSYNC
VSYNC
CVOUT
5.3
CTL(+)
AFCPC
CTL(-)
CTLFB
C1055 R1048
CVIN2
CVIN1
0.1 B 5.2
SVSS
SVCC
AVSS
5.2 MESECAM_M HD
DEW
CFG
29
EOT
0 C1081 HD SW 0.2
5.3 330P CH 220 1/4W
TAB SW
R1063
Q1016
1.2K
0 FROM/TO T’TEXT/RGB SW
R1078
TAB_SW 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
4.7K
0.001 B 2SC2412K
SW1001 0 2.6 2.6 2.6 2.6 0.2 2.7 2.6 2.6 5.2 2 2 1.7 5.1 5.1 2.1 1.5 5.2 NC 0 NC 2.6 0 0 0 1.4 1.4
R1017 OSD_R
R1022
MXS01380MPP0 CTL+ R1070
68K
0.001 B
C1090
R1007
OSD_G
6.3V 220 YK
C1010
5.1 10K
R1026
R1020 OSD_B
10K
6.3V 22 KA
W858
CTL- POWER_FAIL[DC]
C1018
C1027 0.1 B
L1001 12uH
R1080
1K
C1070
10K R1094
C1016 OSD_Y
4.7K
560 4.9 4.9
C1012 BUFFER
6.3V 47 KANP C1038
R1028 6.8K
Q1007
6.3V 22 KA
0.1 B
R1056
0.0039 B 25 2SA1037AK
R1030
0.1 B
C1005
C1013
10K
0.1 B
6.3V 22
SW 15P CH 4.9 SW
C1062
1 B
3 3
C1052
16V 47 YK
C1078 0.1 B
FROM/TO CAPSTAN DD UNIT
KA
Q1004 Q1010
0.0068
5.2
50V 4.7 KA
B
1/4W
R1042
4.7K
FF/REW-L
C1032
ENV_DET
KRC103SRTK
10K
W853
CP1001 0 4.6 KRA103SRTK
H.SYNC
V.SYNC
C1015
C1048
TMC-J12P-B2
EOT
C1035
C1040
0
1 CAP FG 0.0018 B FROM/TO SOUND AMP
2 CAP VCO
OSDG
OSDR
OSDB
3 VCC TV_A_MUTE
R1061
CAP_F/R
4 CAP.M F/R R1029 VOL_CTL
RESET
3.3K 1/4W CAP_LIMIT D1021
5 C1022
P.CON+5V_A
I LIMIT M.P.OFF_H
MS_SEN-B
MS_SEN-A
1K
0.1 F
C1014
16 R1009
REEL-S
1SS133
REEL-T
R1049 0 0
47K 1/4W
R1006
R1019
5.5V 0.1F
47K
2 REEL SENSOR 2
C1003
CYL_FG/PG 4.7K VD
11 CYL FG/PG Q1005 NC NC C1020
CYL_DRIVE MS_SEN A RPI-301 HD
12 CYL CTL Q1009 180P CH
C1009
RPI-352Q02 R1054
R1051
0.022 B
5.6K
1 2 1 2 2.7K
2 3 2 3
1 2 3
5.2 5.1 0 C1033
1 4 1 4
MS_SEN B 180P CH
0.9 1.4 0.5 1.4 4 3 4 3
Q1003 SYSTEM RESET
0 5.1 0 5.1
IC1003
25V 33 YK
100P CH
100P CH
RPI-352Q02
R1083
R1050
R1087
C1050
C1056
C1021
REEL SENSOR
33K
33K
C1017
0.1 B
R3111N311A/C
Q1001
100
RPI-301
A B C D E F G H
G-3 G-4
A B C D E F G H
AT+13V
AT+5.6V
FROM/TO Y/C/A/H.AMP
5V REG. IC P.CON+9V
5V REG. IC
FROM/TO TV POWER IC1001 KIA7805API IC1005 KIA78R05PI P.CON+5V_A
CD401 GND
CP401B (CP401A)
7 CU251201 7
B2013H02-5P
+B FROM/TO MICON
1 +B
2 +B
VCR_POWER_H
3 NC IN GND OUT IN OUT GND SW
POWER_FAIL[DC]
H_GND 1 2 3 1 2 3 4
4 H GND
R1040 P.CON+5V_A
8.0 0.5 5.6 8.2 5.3 0.3 4.9
5 H GND
AT+12V
100 1/4W
P.CON+5V
R1038
6.3V 470 YK
9V REG IC MOTOR_GND
12 1/2W
IC1007 KIA78R09API
C1059
1K 1/2W
GND
R1052
AT+5.6V
FROM/TO TV POWER
6 CD851 CP851B(CP851A) R1016 6
B2013H02-11P IN OUT GND SW
CU2B1201
2201/4W
11 NC 1 2 3 4
POWER_FAIL[DC] 12.8 9.6 0 4.9 R1037
10 POWER FAIL
SOUND+B
9 SOUND+B 100 1/4W
SOUND_GND P.CON+9V
8 SOUND GND
7 UNREG+8V AT+13V
D1002
P.CON+8V
10V 470 YK
UNREG+8V
6 UNREG+8V
C1037
AT+13V 5V REG. IC 11E1-EIC
5 AT+13V
16V 470 YK
MOTOR_GND IC1004 KIA78R05PI
C1041
4 MOTOR GND
AT+12V
6.3V 470 YK
3 MOTOR+12V
100
R1071
221/4W
R1075
C1029
2 GND
1 GND
R1036
5 1K 1/2W 5
IN OUT GND SW
1 2 3 4
8.2 0.3 5.3 4.9
UNREG+8V R1047
470
16V 470 YK
1/4W P.CON+5V
C1042
FROM/TO CHROMA/IF
12 1/4W
6.3V 470 YK
R1060
+B
C1036
P.CON+8V
HS1003 HS1001 HS1002
763WAA0157 763WAA0157 P.CON+5V
763WSA0019
GND
GND
4 P.CON+9V 4
P.CON+8V
GND
3 3
GND
SOUND+B
SOUND_GND
2 2
NOTE: THE DC VOLTAGE AT EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
DURING PLAYBACK PCB010
VMA230
1 1
A B C D E F G H
G-5 G-6
A B C D E F G H
7
6
5
4
3
2
1
FROM/TO OPERATION
9
8
7
6
5
4
3
2
REMOCON OUT 1
CP351(CD351)
FROM/TO OPERATION
A2001WR2-7P
SOUND GND
SOUND OUT L
POWER ON L
CP757_1(CD757)
SP OUT L
T-REC LED
A2001WR2-9P
GND
GND
REC LED
AT+5V
KEY B
KEY A
GND
NC NC
NC R4212
7 FROM/TO SOUND AMP 7
2701/4W
FROM/TO MICON SOUND_GND
SOUND+
W868
KEY_B SP_OUT
(UK)
REC_LED
W828(UK)
T-REC_LED
W869 C4206
KEY_A
(UK)
22K
0.01 B
R4209
REMOCON_IN
POWER ON SW
STANDBY_H Q4203
4.3 2SC2412K
FROM/TO POWER
0.1 F
5.0
C4203
AT+5V 5.2 P.CON+5V
C4217
6 TUNER_ON/OFF 6
GND
EXT_IN_L 0.1 F
P.CON+8V
TU_AUDIO_MUTE_H
P.CON+5V
P.CON+8V
21_R
21_G
21_B
5 75 1/4W
5
R4224
19
TP4201 C4209
NC
VIDEO OUT
W4BRH3.5X6X1
L4204
16V 10 KA
10uH
680
R4220
B4201
16V 10 KA
68 82 75 MUTE SW
20
Q4205
C4204
1SS133
2SC2412K 0
D4210
FROM/TO CHROMA/IF
0 2.5 0 0 0 0 0 0 0 0 0
21 19 17 15 13 11 9 7 5 3 1 TUNER_A
J4201
20 18 16 14 12 10 8 6 4 2
0350_9982_05 JACK_V
0 0 0 0 0 0 0 0 0 0 21_Y
4 NC NC W817 4
21_R
B4202 C4230 21_G
21_B
W4BRH3.5X6X1 C4215 470P CH
21_Y W804 W805
0.001
CH
W900
FROM/TO Y/C/A/H.AMP
L4203 R4202
56K 1/4W
REAR_A_IN_L
R4201
10uH 33K1/4W
REAR_V_IN
R4228
5.0
120K
R4210
R4208
TUNER_ON/OFF
6.8K
4.7K 0
0
3 TUNER SW 3
Q4210
2SC2412K
R4239
4.7K
C4201
22K
2 2
16V330 YK
C4213
W807
5.1
C4202
0 0
1.8 R4225
1
BUFFER PERI SW
100 0
0 Q4202 Q4207
2SA1037AK 2SC2412K
0.018 B
C4205
R4205
A B C D E F G H
G-7 G-8
A B C D E F G H
100uH
L611
7 7
6.3V 100 KA
BUFFER L608
CF601_1
C636
Q608
W889
TSF5372P
TEST POINT 2SC2412K R604 18uH R649 8.1
IN GNDOUTOUT 2.0 BUFFER
CP603 1 2 3 4 8.1 3.9 220 470 Q602
KA
06JQ-ST 1.5 2SC2412K FROM/TO SOUND AMP
3.9 TUNER_V
C611
820
R619
B.OUT
6 B.OUT CF605 AUDIO_OUT
16V 100
R614
AGC_M
W888
5 AGC
1K
TPS6.0MB
R658
100 1/4W IIC_OFF
4 IIC OFF
SDA
3 SDA VCO COIL R626
R603
1K
SCL Y/C_V
2 SCL L612
3700005 1K
1 GND
16V 10 KA
6 6
330K
0.33 B
50V 1 KA R622
4
1K
75
C607
R625
R621
C605 0.001 B
0.1 B
C621
0.022 B
W862
C648
C645
R657
1.2K
21_Y
16V 47 KA
0.001 CH
3
2
1
B
0.1 B
TO DECK SHILD
C618
C646
C675
C652
C654
50V 1 KA
NC
270
C657
R618
0.01 B
21_B
0.022
50V 1 KA
C643
C601 3P CH
50V 3.3 KA C662
C610
50V 1 KA
50V 1 KA
C613
C603
21_G
0.01 B
33K
C626
R636
C640
KA
W836 R616
TUNER_A C651 50V 3.3 KA
21_R
C641
50V 0.1
13 12 220
0.1 B
0.1 B
50V 3.3 KA
0.1 B
W837
AGC 1 L614
C659
C660
C623
0.2
2 NC 1uH NC
NC NC NC 3.3 2.6 2.6 2.6 4.0 2.2 0 6.1 5.1 5.1 3.0 4.2 4.2 8.1 4.8 0 3.0 5.0 0 1.9 3.6 3.6 3.6 0 FROM/TO DEFLECTION
7.2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
3 NC
AGCPIF_CAP
FM_OUT
GND2
INT_CVBS_OUT
CHR
CVBSIN1
APR
GND_IF
(8V) VCC2
EXT_AUDIO_IN
(5V) VCC_IF
B_EXT/U_EXT
G_EXT/Y_EXT
R_EXT/V_EXT
BLK_EXT
AGCSIFCAP
RF_AGC_OUT
CVBSIN2
Y/CVBS_IN3
VREF_IF
PIF_LC1
BS
PIFIN1
IFPLL
PIF_LC2
PIFIN2
5 1.3 5
SIFIN1
SIFIN2
W953 H_OUT
SCL 4 H_OUT
4.8 W905 V_AMP
W844 TUNER_A_YC V_AMP
SDA 5 V_OUT
4.8 V_OUT
R656
4.7K
ABCL
6 NC ABCL
0.1 L602 HD
P.CON+5V HD
+5V 7
UE25-B59D
5.0 100uH
X1/VAMP/CHR_OUT
STV2246C
MONITOR TUNER
8 NC 9A06B HEATER
0.2
10V 220 YK
H_GND
0.01 B
+30V 9
C604
AUDIO_OUT
VCC_D (5V)
C627
CVBSOUT2
29.9
VCC1 (8V)
180V
LBF/SSC
BCL/SAF
FM_CAP
OSD_BK
TU601
GND_D
OSD_R
OSD_G
H_OUT
OSD_B
10 NC
XTAL1
XTAL2
XTAL3
R.OUT
G.OUT
B.OUT
ICATH
GND1
CHROMA
VERT
SLPF
CLPF
SDA
SCL
0
NC
IC601
P.CON+8V
IF 11 TO CRT
0
1K
R662
15 14 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
4 CP852A (CP852B) CD852 4
100uH
L604
2.1 3.8 0 5.1 4.8 4.8 4.1 0.3 0.9 4.9 6.8 8.2 NC 0 3.8 3.0 2.4 NC NC 2.3 4.9 4.9 4.8 NC 3.8 3.8 3.9 NC WDL6036038
MTZJ33B
R645
0.1 F
B2013H02-6P
C655
16V100 KA
TP601
R643 470
16V 1000 YK
D601
0.1 B
0.1 B
0.1 B
0.1 B
IF
2.2K
47K
180V 1
50V 1 KA
C658
C619
C620
220
220
220
R646
R628
R629
R630
21
16V 100 KA
C642
0.0047 B 15K
33K
NC R624
R641
R679
C649
C666
NC 2
10K
0.01 B
C609
0.0047 B
C634
R635
4.433619MHz
R638
2.2K
C656
C653
H GND 3
R642
75 P.CON+8V
1/2W
100 1/4W
X601
HEATER 4
R609
100uH
B.OUT
820
R615
1K
220
220
16V 10 KA
220
R610
R611
R612
R613
1 B
NC 5
G.OUT
6.8K
CUT_OFF
56K
L610
CUT OFF 6
C630
C615
L606
56K 1/2W
AUDIO_OUT R.OUT
2.2uH
R602
0.22uH
1 F
CF603 0.01 B
FROM/TO POWER MKT31.5MA110P
C614
C650
6.2
+B PRE AMP TO CRT
1.3 Q607 R637
P.CON+8V 2SC3000 SDA C677 CD853
R639 CP853A (CP853B)
P.CON+5V 0.6 100 R640 0.1 B B2013H02-4P
WBL6028038
3 SCL
6.8K
TEXT_B
R.OUT 3
W857
GND R.OUT 1
MKT41.5MA110P
100 TEXT_G
P.CON+5V B.OUT
P.CON+9V B.OUT 2
G.OUT
CF604
G.OUT 3
TEXT_R
16V 22 KA
R678
4
8.2K
R608
2.2K
TEXT_Y GND
C635
1 F
0.01 B
R634
C639
C647
47
1SS133
V_AMP
1SS133
1SS133
D610
D611
D609
680P CH
JACK_V
11E1-EIC
11E1-EIC
D602
D603
C664
R648 ABCL
22K
V_OUT
W887
FROM/TO T’TEXT/RGB SW
H_OUT
P.CON+9V
TEXT_B R647
HD
1 F
2 TEXT_G 2
C670
560 R605
TEXT_R CUT_OFF
TEXT_Y 1/4W680
R665
10K
P.CON+8V
8.3
SW
8.3
Q601
FROM/TO Y/C/A/H.AMP 8.3 KRA102SRTK
SW 0 R664
TUNER_A_YC Q611
0
16V 10
Y/C_A
TUNER_V
SPOT_OFF
0 2SC2412K 820 1/4W PCB010
C668
Y/C_V
KA
Y/C_A VMA230
A B C D E F G H
G-9 G-10
A B C D E F G H
(SYSCON PCB)
SOUND AMP IC
IC352 AN7523
7 7
1 2 3 4 5 6 7 8 9
8.2 3.5 0 3.4 3.9 0.3 0 NC 0.1
W839
FROM/TO 21PIN I/O R308
6 6
1K
SP_OUT
22
SOUND+
SOUND_GND
C359
FROM/TO MICON
0.01 B
M.P.OFF_H R359
R353
TV_POWER_H 4.7K
0.1
R355 68K
0.8 A_MUTE SW
TV_A_MUTE
5 10K Q351 5
VOL_CTL 0 2SC2412K
FROM/TO POWER
C357
SOUND+B 25V1000 YK
3.3 3W
R356
SOUND_GND
W902
W893
GND
4 4
FROM/TO CHROMA/IF
AUDIO_OUT
16V 10 KA
C352_1
50V 10 YK
C351
3 3
0.022 B
C362
0.001 B
R352
560
C361
R361 C355
2 2
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PCB010
VMA230
1 1
A B C D E F G H
G-11 G-12
A B C D E F G H
(SYSCON PCB)
7 7
FROM/TO CHROMA/IF
W801 W847
TEXT_B
W802 W815
TEXT_R
W812 W816
6 TEXT_G
D1261 6
TEXT_Y
1SS133
FROM/TO MICON
OSD_R
OSD_G
OSD_B
5 5
OSD_Y
4 4
3 3
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
2 2
PCB010
VMA230
1 1
A B C D E F G H
G-13 G-14
A B C D E F G H
8
DEFLECTION SCHEMATIC DIAGRAM (SYSCON PCB)
8
RAMP GENERATOR
OUTPUT STAGE Vs
INVERTING INPUT
BUFFER OUTPUT
POWER OUTPUT
FB. GENERATOR
TRIGGER INPUT
Vref. DECOUP.
TO DY
HEIGHT ADJ.
CP402
A1561WV2-A5P
GND
Vs
5
7 1 2 3 4 5 6 7 8 9 10 11 4 7
1.6 2.6 4.9 6.8 4.5 0 5.4 6.0 4.4 2.6 1.9 3
R412
4.7K
+-1%
NC 2
0.047 MMTV
R404
1
50V 10 YK
330K1/4W FB401_1
C408
35V 470 YK
35V 100 YK
R403
C412
FQI-14B001
0.1 F
390K
C413
C410
COL
C414
1 HV
D403
C401 VIDEO F
11E1-EIC 6
3301/2W
23
L402
500V 68P SL
S
METAL
R413
B+
330 1/2W
1/2W
V.LIN
VR401
W833
W825
ELH5L4112N 2
2.2K METAL
GND
R409
R411
470
6 R406 R420 R448 11 6
AFC
NC 9
330
HEA ABL
VR402
2.7K 1/4W 4.7K 1K 1W 7
10 TER
R419
V.POSI
GND
R416
R417
1.8K
2KV 220P R
6801/2W
C405
E12
C417
NC 4 GND
8
R421
E25
MKT
3
FROM/TO Y/C/A/H.AMP E8
5
C403
HS401 NC
R407
R405
763WSAA013 V801
VD A34AGT13*07(L)
C431 D413
220 3W 11E1-EIC
FROM/TO MICON 8
D406
6 G
0909
D404 B
VD 11
R430
SWITCHING 11E1-EIC
4.1
C423
C422
R426 Q403
H_CTL 2SC2412K
4.7K 1.3
0.7
HD
TO CRT
R447
1 2
W880
CD801(CP801)
FROM/TO TV CHROMA/IF
W823
V_AMP 24
4 4
T401 247.6
ETH09K14BZ 1.3
V_OUT
2KV 0.0012 R
0 H.OUTPUT
C424
500V 56P NC
C425
B401 W4BRH3.5X6X1
2 Q406
C404
SL 0.2
2SD2627LS-CBC11
HD 1 6
31.0 22.3 FOCUS
ABCL 1.3
100 1/4W
R410
W901
W814
W849
W904
0.5
50V 22 MHE
180V C429
R460
H-DRIVE HS402 TO CRT
220 1/4W
R456
C418
H_GND
35V1000 MHE
3 AT+13V 3
R450
C421
+B 5.6 2W
GND
E0 REAK
TP401
W852
68K 1/4W
11E1-EIC
D405
C432
R490
W890
W808
D407
2 2
R453
11E1-EIC
220K 1/4W
PCB010
VMA230
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
IS NON POLAR ONE.
DANS LA NOMENCLATURE DES PIECES
1 1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A B C D E F G H
G-15 G-16
A B C D E F G H
0 0
J801_1 126.5
HPS3200-010501 6
0 5 7 104.1
4 8
3 9 127.5
127.5
1
TP801 F
0
7 BLUE AMP 25 R802 7
Q804_1
KTC4217 132.5 15K 1W
R807
2.8
2.5 2.7K 1/4W
R814
6.8K
6 6
FROM CHROMA/IF
CP853B (CP853A)
B2013H02-4P
(POWER SW PCB)
R811
GND
4 GND
G.OUT 270 FROM/TO TV POWER
3 G.OUT
B.OUT C809 TP802
2 B.OUT
CD502
R.OUT 680P B
1 R.OUT 26 R805 CUU23001
GREEN AMP
Q805_1
1
KTC4217 132.1 15K 1W
2.9
2
2.5
C822
5 FROM CHROMA/IF 5
220P CH R808
CP852B(CP852A)
B2013H02-6P S101 S102
2.7K 1/4W
CUT_OFF
6 CUT OFF
BROWN BLUE
5 NC
HEATER
4 HEATER
H_GND
R815
3 H GND
6.8K
2 NC MAIN POWER SW
1
2
180V SW501
1 180V SDKVA30200
R812 C821
4
3
270 220P CH
C810
270P B
4 4
XRY20X30BD XRY20X30BD
TP803
R810 BLUE
S501 S502
BLUE
15K 1W
PCB340
BROWN
TEAA79 BROWN
AC230V-240V 50Hz
27 CD501
RED AMP R820
06439801
Q806_1
KTC4217 132.3 2.7K 1/4W
2.8
2.5
3 3
W864
R816
6.8K
C801
R813
2KV0.0022 B
270
220uH
L801
C811 ACCESSORY
390P B TM101
R25-1706
C805
2 2
SCREEN
FOCUS
100P CH
BT101
R03(AB)2PXGPI
FROM DEFLECTION
FROM DEFLECTION
A2361WV2-2P
CP801(CD801)
BT102
R03(AB)2PXGPI
GND
GND
PCB110
TCA375
S801
2
1
1 1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-17 G-18
A B C D E F G H
C516
500V470P B
D505
C520
SB290S
250V 0.001 KX
7 7
W5RH3.5X5X1.0
C530
FROM/TO POWER
B501_1
CP401A(CP401B)
D510_1 A2001WV2-5P
W804
DEGAUSS COIL +B 1
L503 RU2AM-EIC
+B 2
220K 1/2W
(028R140018) CP502
C517 NC 3
A1561WV2-2P
C521
R509
H GND 4
1 2KV 0.0012 R
H
1
1
R501_1
H GND 5
2 2
2
2.2 5W R505
P
3
L501
0R7A223F24 0.22 1W
TH501
RM11C-EIC
RM11C-EIC
B59104-T80-B10
6 6
D501
4 3
D502
D511 R511
2 1 1N4937 1K 1/4W
FROM/TO POWER
MTZJ15B
D515
CP851A(CP851B)
C502 C503 A2001WV2-11P
L502
100V 10 MHE
400V150 USR
NC 11
1R0A103F24
2KV 0.0022 B 2KV 0.0022 B
C507
C537
POWER FAIL 10
RM11C-EIC
275V 0.22 PHE840
RM11C-EIC
SOUND+B 9
C506
D503
D512
4 3
1.5M 1/2W
D504
SOUND GND 8
R538
SB290S
C505
UNREG+8V 7
2 1 C504
F501 UNREG+8V 6
16V2200 MHE
T4A_L_250V 500V 470P B
T50040HCC AT+13V 5
5 5
C531
MOTOR GND 4
W808
MOTOR+12V 3
FH501 FH502 POWER REG. IC
EYF-52BC EYF-52BC GND 2
R504
R515
BROWN
+-
O.S.C
1
+-
DRIVE
BLUE
R516
REG. T.S.D
2
R510
START O.V.P LATCH
CP501
A3963WV2-3PD 1 2 3 4 5
206.0 0 0 15.8 2.5
D523 R514
SB140-EIC
D520
MTZJ6.8B 68K 1/4W
2KV 0.0012 R
B505
4 4
W4BRH3.5X6X1.0X2
C535
D508 W811
0.001 B
50
RU2AM-EIC
C512
51
25V2200 MHE
3.3K 1/2W
W4BRH3.5X6X1.0X2
C501
R503
C523
SB140-EIC
B502
2KV 470P R
D522
D506 R502
T501
7.3 81290794
1N4937 4.7 1/4W
4
1
C509
M
0.027
DC IN SB
8 11
C510
6.0
308.3
1SS133
3 3
D518
FEED BACK P2
FEED BACK 0 D535
IC506 344.5 SG
SWITCHING 5.4 7 12
VR502 470
KTC3198 13.0
R506 D521 13V
3901/4W
6 13
344.5 D519
R533
39K 1/2W
8V SB290S
5 14
397.2 COL
0.0015 B
0.22 1W
C515
0 C519
LG
R542
HS501 15
1/4W
763WAA0174 500V470P
R532
22K 1/2W
135.0
GND1 NC 3 NC 16
100
0
2.7K 1/4W +-1%
C524
250V 0.0022 KX
2 17
GND HG
1SS133
1SS133
1SS133
2 P3 2
R529
12.7
D533
C529
D534
D526
MTZJ5.6B
1 18
D528
ADJ 12V
16.5
CAUTION: IS THE LIVE CONNECTION
PCB020
VPA150
1 1
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
IS NON POLAR ONE.
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-19 G-20
A B C D E F G H
(OPERATION PCB)
7 7
ON TIMER/STAND-BY
100 1/2W
LTL-4224-031A
OS753
R766
REC/OTR
T-REC
D793
D791
D794
PIC-37143TH5
0
3 GND
5.0
FROM/TO 21PIN I/O 2 B+
5.0
W808
1 Vout
CD757_1(CP757)
R793_2
R754_2
CU292502
R771_1 R772_1 R773_1 R774_1
1 REMOCON OUT
6.3V 220 KA
1K 1/4W 1.5K 1/4W 2.7K 1/4W 5.6K 1/4W
820 1/4W
100P B
POWER ON/OFF
820 1/4W
C751
0.1 F
C752
2 GND
C755_1
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
STOP/EJECT
REW/REV
REC/OTR
SW751
SW795
SW791
SW792
SW793
SW794
3 AT+5V
FF/CUE
R759_1
PLAY
R760_1
6 4 POWER ON L 6
5 NC
6 KEY A
7 T-REC LED
0.001 B
8 REC LED
C779
R776_1 R777_1
9 KEY B
1K 1/4W 1.5K 1/4W
EVQ21505R
EVQ21505R
EVQ21505R
CH DOWN
VOL DOWN
EVQ21505R
SW799
SW798
SW796
VOL UP
SW797
CH UP
HEADPHONE JACK
J351
5 B701 HTJ-035-28A 5
1
W5RH3.5X5X1.0
NC 5
R350
4
56 1/2W
W811
3
R351
2
B702
56 1/2W
6
W4BRH3.5X6X1.0X2
7
4 4
16V 47 KA
C382
3 3
CD351_1(CP351)
CU272502
1 NC
2 GND
3 NC
4 SOUND GND
2 5 SOUND OUT L 2
6 SP OUT L
7 GND
SPEAKER CD352
1 SP + PCB030
2 SP - TE9962
8 OHM CU121701
SP351
NF-16D27W
1 1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A B C D E F G H
G-21 G-22
A B C D E F G H
INTERCONNECTION DIAGRAM
TM101
8 HEADPHONE JACK 8
OS753
J351
1 3 GND
5 OPERATION PCB
2 B+
PCB030
4 1 Vout
TE9962
3
2
6
HALL MAIN ROTOR MR
7 SENSOR COIL MAGNET FG SENSOR
SOUND GND
SOUND OUT L
REMOCON IN
POWER ON L
T-REC LED
SP OUT L
REC LED
CAPSTAN DD UNIT
GND
GND
AT+5V
GND
KEY B
KEY A
SPEAKER CD352
VCC
M2001
O
G
1 SP +
CD351
CD757
7 2 SP - 7
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
SP351
8 OHM
CP351
CP757
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
COIL
L503 CP401A CD401 CP401B
REMOCON IN
POWER ON L
SOUND GND
SOUND OUT L
T-REC LED
CP502
REC LED
SP OUT L
AT+5V
+B 1 1 +B
KEY B
KEY A
GND
GND
GND
2
2 +B 2 2 +B
LM
1
1 3 3
H GND 4 4 H GND LOADING MOTOR
M101
H GND 5 5 H GND CP1001
6 6
1 CAP FG 1
CP851A CD851 CP851B 2 CAP VCO 2
11 11 3 VCC 3
POWER FAIL 10 10 POWER FAIL 4 CAP.M F/R 4
SOUND+B 9 9 SOUND+B 5 I LIMIT 5
SOUND GND 8 8 SOUND GND 6 MOTOR GND 6
UNREG+8V 7 7 UNREG+8V 7 GND 7
UNREG+8V 6 6 UNREG+8V 8 CYL/LAD VCO 8
AT+13V 5 5 AT+13V 9 CAP CTL 9
MOTOR GND 4 4 MOTOR GND 10 LDM CTL 10
MOTOR+12V 3 3 MOTOR+12V 11 CYL FG/PG 11
GND 2 2 GND 12 CYL CTL 12
5 POWER PCB 5
PCB020 GND 1 1 GND
VPA150
7
6
5
4
3
2
1
D-PG GND
D-PG OUT
D-W OUT
D-U OUT
M-GND
D-V OUT
D-COM
CYLINDER UNIT
UN4001
S102 CD502 CP501
S502
BLUE
1
7
6
5
4
3
2
1
BROWN S501 POWER SW PCB S101
2
V801 FFC
CRT CP4005
CD4005
ANODE AUDIO PB 6 6 AUDIO PB AUDIO
AUDIO REC 5 5 AUDIO REC
H.V
FOCUS
CTL+ 4 4 CTL+
CTL- 3 3 CTL- CONTROL
DY
CD801
3 AE HEAD(-) 2 2 AE HEAD(-) 3
J4201
AE HEAD(+) 1 1 AE HEAD(+)
1 CP401 AE
2 NC
21
CP801
3
20
GND 1
4
19
GND 2 TU601
5
18
CP4004
14 15
17
CP852B CP852A 10
4 8 CD852 H5002
14
CRT SOCKET 2 2
9
12
3
NC
J801 8
H GND 3 3 H GND
2 2
11
5 5
1
NC
9
6
F CUT OFF 6 6 CUT OFF
8
5 SDA
7
B.OUT 2 2 B.OUT
3
4
G.OUT 3 3 G.OUT
CRT PCB
NC
3
GND 4 4 GND 2
PCB110
2
TCA375
1 AGC
1
12 13
1 1
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-23 G-24
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
101 A54526M720 CABINET,FRONT ASS -Y 201 8110630A04 SCREW,TAP TITE (P) BRAZIER 3x10
102 701 WPJA637 CABINET,FRONT 202 8110630804 SCREW,TAP TITE (P) BRAZIER 3x8
103 711 WP DA217 PLATE,FRONT 203 8121J50B54 SCREWTAPPING (B0) GW20 5x28
104 7230006762 SHEET,LED 204 810A130A04 SCREW/WASHER (A) M3x10
105 713WPA0079 GUIDE,REMOCON 205 8110630A24 SCREW,TAP TITE (P) BRAZIER 3x12
106 712WPJA449 FLAP 206 810B130A04 SCREW/WASHER (B) M3x10
107 743WKA0032 SPRING,FLAP 207 810B130804 SCREW/WASHER (B) M3x8
108 735WPJA087 BUTTON,FRAME 208 8109630802 SCREW,TAP TITE (B) BRAZIER 3x8
109 755WNA0010 SHEET,PVC 209 810A130B04 SCREW/WASHER (A) M3x20
110 800WR00022 SHEET,CRT SUPPORT (A) 210 810A130604 SCREW/WASHER (A) M3x6
111 800WR00064 SHEET,CRT SUPPORT (D) 211 810A130504 SCREW/WASHER (A) M3x5
112 741WUA0013 SPRING,EARTH 212 8110330804 SCREW,TAP TITE (P) FLAT 3x8
113 753WSA0122 PLATE,SPEAKER 213 8110230A02 SCREW,TAP TITE (P) BIND 3x10
114 800WFAA003 CUSHION 10x15xT4 214 8107226604 SCREW,TAP TITE (S) BIND 2.6x6
115 --- COATING CLIP 215 8117540A64 SCREWTAPPING (B0) TRUSS 4x16
116 899EFB0692 COATING CLIP EFB0692 216 8117540B04 SCREWTAPPING (B0) TRUSS 4x20
117 --- HEAT SINK 217 8117140A24 SCREWTAPPING (B0) PAN 412
118 --- HEAT SINK 218 8107630604 SCREW,TAP TITE (S) BRAZIER 3x6
119 --- HEAT SINK 219 8107230804 SCREW,TAP TITE (S) BIND 3x8
120 --- HEAT SINK 220 8110630604 SCREW,TAP TITE (P) BRAZIER 3x6
121 --- METAL SPACER
122 8995034000 CORD CLIP UL CO. --- JB5XD400 POLY BAG
123 761WPA0150 HOLDER,FBT --- J4C10117 REGISTRATION CARD
124 761WPA0164 HOLDER,DECK --- J4D11402 GUARANTEE CARD
125 753WSA0118 PLATE, EARTH-SYSCON --- J5452601 INSTRUCTION BOOK
126 752WSA0144 SHIELD,CASE HEAD AMP --- J5452607 QUICK SET-UP SHEET
127 753WUA0051 SPRING,EARTH HEAD AMP --- 791MHA0002 LAMIFILM BAG
128 771WPA0232 PLATE,JACK --- 792UHAA011 PACKAGE,TOP
1 29 752WSA0153 PLATE,DECK SHIELD --- 792UHAA012 PACKAGE,BOTTOM
--- 793UCDA397 GIFT BOX
130 890PS70100 PUSH SPACER
131 761WPAA018 HOLDER,M/PCB
132 761WPAA019 HOLER,BACK
133 702UPA0139 CABINET,BACK
134 722426A018 SHEET,RATING
135 752WSA0148 SHIELD,CASE
136 752WSA0149 SHIELD,COVER
137 753WSA0120 PLATE, BOTTOM-EARTH
138 735WPJA092 BUTTON,POWER
139 752WSA0147 PLATE,SHIELD BOTTOM
J2-1