Professional Documents
Culture Documents
02 .DACC. 15361-Rev1
02 .DACC. 15361-Rev1
02 .DACC. 15361-Rev1
PROJECT
PROCESS AREA8
FOUNDATION SUPPORTS
CALCULATION NOTE
Audubon Engineering
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
TABLE OF CONTENTS
1 GENERAL ................................................................................................................ 3
1.1 Project Description ..................................................................................... 3
1.2 Scope .......................................................................................................... 3
2 CODES & STANDARDS ......................................................................................... 3
3 ENVIRONMENTAL DATA ................................................................................... 3
4 REFERENCE DOCUMENTS ................................................................................. 3
5 CHARACTERISTICS OF MATERIALS .................................................................. 4
5.1 CONCRETE .............................................................................................. 4
5.2 STEEL FOR REINFORCEMENT............................................................ 4
5.3 CHARACTERISTICS OF THE GROUND .............................................. 4
5.4 APPLIED LOADS ..................................................................................... 4
5.5 COMBINATIONS FOR LOADS .............................................................. 5
6 RESULTT OF CALCULATION:.............................................................................. 6
6.1 FOUNDATION TYPE 1 .......................................................................... 6
6.2 FOUNDATION TYPE 2 ........................................................................ 10
6.3 FOUNDATION TYPE 3 ........................................................................ 13
6.4 FOUNDATION TYPE 4 ........................................................................ 16
6.5 FOUNDATION TYPE 5 ........................................................................ 19
6.6 FOUNDATION TYPE 6 ........................................................................ 22
6.7 FOUNDATION TYPE 7 ........................................................................ 26
6.8 FOUNDATION TYPE 8 ........................................................................ 29
6.9 FOUNDATION TYPE 9 ........................................................................ 33
6.10 FOUNDATION TYPE 10....................................................................... 36
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
1 GENERAL
1.1 PROJECT DESCRIPTION
Eni Tunisia BV intends to construct an onshore oil and gas-processing facility plant as part of Maamoura &
BARAKA offshore fields development Project.
Hydrocarbon gas and liquids brought onshore via two subsea pipelines will be treated at an onshore gas-
processing facility at MAAMOURA Point. Liquids (condensate and LPG) will be separated, processed and
stored. The produced sales gas and after treatment (acid gas removal, dehydration, wobbe Index control) will
be transported via pipeline to a tie-in point to an existing 10” pipeline north west of Hammamet, owned by
STEG, the National Electricity and Gas Company.
The onshore gas-processing facility will be designed for a nominal design life of 20 years, with an
approximate processing capacity of 0.85 MMSm3/day gas and associated liquids around 2000 m3/day,
obtained through the installation of one single train. The CPF will serve the following purposes:
- Associated wet gas will be sweated by gas acid removal, dehydrated, and stripped of heavy hydrocarbons
to sales quality specifications and compressed prior to be exported;
- Condensate and LPG will be recovered and stored prior to be sold and transferred by trucking.
- The produced water and the water used for oil washing is collected and treated in a suitable waste water
treatment plant before to be transported by truck for injection in Belli Water disposal well.
- Utilities and buildings will be constructed to support base operations.
1.2 SCOPE
The present calculation note concerns the foundations under “Pipe support” of Area 8; it aims is to verify
the stability and the reinforcement of the foundation.
2 CODES & STANDARDS
The foundation of PIPE RACK is designed in accordance with the following standards and rules:
•
BAEL 91 mod. 99 French rules for concrete calculations
•
Fascicule N° 62 – Titre V French booklet for Geotechnical calculations
•
ASCE 7-05 American rules defining effects of snow and wind
• UBC 1997 American rules defining para-seismic construction
3 ENVIRONMENTAL DATA
• Ambient temperature: Min = -1 C° and Max = 47 C°;
• The average overall direction of the winds is supposed horizontal.
• According to ‘ASCE 7-05’,
• Wind velocity = 125 MPH.
• Site EXP = C;
• Class II.
• Kzt = 1.
• Kd = 0,85.
• I=1
• Rainfall = 108 mm/h.
• Earthquake = Zone II according to UBC 1997:
4 REFERENCE DOCUMENTS
• General specification – concrete works : 3314-02-BA-SG-15014
• Etude geotechnical: AS-018/2009
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
5 CHARACTERISTICS OF MATERIALS
5.1 CONCRETE
Bearing pressure of the ground in absolute limit of service σsoil = 3,0 Bars,
Wet soil density ρsoil = 1800 kG/m3,
Internal friction angle φ = 30 Deg,
Cohesion C = 0 daN/cm2,
5.4 APPLIED LOADS
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Data:
Analysis mode : Modal
Method : Subspace iteration
Type of mass matrix : Lumped without rotations
Number of modes : 30
Number of iterations : 40
Tolerance : 1.00000e-004
Damping : 0.050
Acceleration(m/s^2)
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
Period (s)
0.0 0.0 1.0 2.0 3.0
Spectrum parameters:
Acceleration : aN = 3.000
Damping : x = 0.050
Damping correction : ρ = (5/ξ)0,4 = 1.000
TB = 0.150 TC = 0.300 TD = 2.670 RM = 2.500
RA = 1.000
5.5 COMBINATIONS FOR LOADS
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
1.00SIS_Z7
23/ACC :
1.00DL+0.50WIND1+1.00SIS_X6+1.00SIS_Y7+1.00SIS
_Z7
24/ACC : 1.00DL+0.50WIND1-1.00SIS_X6-1.00SIS_Y7-
1.00SIS_Z7
25/ACC :
1.00DL+0.50TEMP1+1.00SIS_X6+1.00SIS_Y7+1.00SIS
_Z7
26/ACC : 1.00DL1+1.00DL2+0.50TEMP1-1.00SIS_X6-
1.00SIS_Y7-1.00SIS_Z7
27/ELU : 1.35DL1+1.35DL2+0.80TEMP1
28/ELU : 1.35DL1+1.35DL2
29/ELU : 1.00DL1+1.00DL2+0.80TEMP1
30/ELU : 1.00DL1+1.00DL2
31/ELU : 1.35DL1+1.35DL2+1.80WIND1+0.80TEMP1
32/ELU : 1.35DL1+1.35DL2+1.80WIND1
33/ELU : 1.00DL1+1.00DL2+1.80WIND1+0.80TEMP1
34/ELU : 1.00DL1+1.00DL2+1.80WIND1
35/ELS : 1.00DL1+1.00DL2+0.60TEMP1
36/ELS : 1.00DL1+1.00DL2
37/ELS : 1.00DL1+1.00DL2+1.00WIND1+0.60TEMP1
38/ELS : 1.00DL1+1.00DL2+1.00WIND1
39/ACC : 1.00DL+1.00SIS_X6+1.00SIS_Y7+1.00SIS_Z7
40/ACC : 1.00DL1+1.00DL2
41/ACC : 1.00DL-1.00SIS_X6-1.00SIS_Y7-1.00SIS_Z7
42/ACC :
1.00DL+0.20WIND1+1.0SIS_X6+1.0SIS_Y7+1.0SIS_Z7
43/ACC : 1.00DL1+1.00DL2+0.20WIND1-1.00SIS_X6-
1.00SIS_Y7-1.00SIS_Z7
44/ACC :
1.0DL+0.50TEMP1+1.0SIS_X6+1.0SIS_Y7+1.00SIS_Z7
45/ACC : 1.00DL1+1.00DL2+0.50TEMP1-1.00SIS_X6-
1.00SIS_Y7-1.00SIS_Z7
6 RESULT OF CALCULATION:
The stability checking and the reinforced concrete of the foundation are led by the ROBOT program.
6.1 FOUNDATION TYPE 1
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Geometry:
A = 1,00 (m); a = 0,65 (m); B = 1,00 (m); b = 0,65 (m); h1 = 0,30 (m); ex = 0,00 (m);
h2 =0,70(m); ey = 0,00 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 46,0 (cm) b' = 46,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m) (daN*m)
DL1 dead load 1 367,09 -2,85 0,00 0,00 -2,15
DL2 dead load 1 775,47 -35,17 0,00 0,00 -26,46
WIND1 wind 1 -152,52 -112,32 0,00 0,00 -81,86
TEMP1 temperature 1 0,00 0,00 -116,15 -270,29 0,00
SIS_X6 seismic 1 707,58 -543,07 0,00 0,00 -404,12
SIS_Y7 seismic 1 0,00 0,00 -395,59 -649,25 0,00
SIS_Z7 seismic 1 326,12 -7,82 0,00 0,00 -5,86
Soil:
Stresses in soil: σULS = 4.50 (daN/cm2) σSLS = 3.00 (daN/cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Stress calculations
Soil type under foundation: not layered
Design combinationACC : 1.00DL+0.50WIND+1.00SIS_X6+1.00SIS_Y7+1.00SIS_Z7
Load factors: 1.35 * Foundation weight
1.35 * Soil weight
Calculation results: On the foundation level
Weight of foundation and soil over it: Gr = 3216,02 (daN)
Design load:
Nr = 5316,02 (daN) Mx = -174,54 (daN*m) My = -1253,62 (daN*m)
Equivalent foundation dimensions:
B' = 1 L' = 1
Foundation depth: Dmin = 1,00 (m)
Allowable stress calculation method: Stress pressiometric (SLS), (Fascicule No 62 - Titre V, B.1.)
q SLS = 3.00 (kG/cm2) qu = 8,64 (kG/cm2)
Design soil pressure:
qlim = (qu - q'0) / γf + q'0 = 5.82 (kG/cm2) γf = 1,50
q'0 = 0,18 (kG/cm2)
Stress in soil: qref = 1.13 (kG/cm2)
Safety factor: qlim / qref = 5.146 > 1
Uplift
Uplift in ULS
Design combination ELU : 1.00DL+1.50TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 2382,23 (daN)
Design load:
Nr = 3524,79 (daN) Mx = -196,36 (daN*m) My = -74,24 (daN*m)
Contact area s = 100,00 (%)
slim = 10,00 (%)
Uplift in SLS
Design combination: ELS : 1.00DL1+1.00DL2
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 2382,23 (daN)
Design load:
Nr = 3524,79 (daN) Mx = 0,00 (daN*m) My = -74,24 (daN*m)
Contact area s = 100,00 (%)
slim = 100,00 (%)
Sliding
Design combination ELU : 1.00DL+1.50WIND1+0.90TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 2382,23 (daN)
Design load:
Nr = 3296,02 (daN) Mx = -117,82 (daN*m) My = -399,21 (daN*m)
Equivalent foundation dimensions: A_ = 1,00 (m) B_ = 1,00 (m)
Sliding area: 1,00 (m2)
Cohesion: C = 0.00 (kG/cm2)
Foundation/soil friction coefficient: tg(φ) = 0,58
Sliding force value F = 231,46 (daN)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 0,80 (m); a = 0,45 (m); B = 0,80 (m); b = 0,45 (m); h1 = 0,30 (m); ex = 0,00 (m);
h2 =0,70(m); ey = 0,00 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 35,0 (cm) b' = 35,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m)(daN*m)
DL1 dead load 1 19,92 0,00 0,00 0,00 0,00
DL2 dead load 1 400,00 0,00 0,00 0,00 0,00
WIND1 wind 1 0,00 80,00 0,00 0,00 24,00
TEMP1 temperature 1 0,00 0,00 120,00 -36,00 0,00
SIS_X6 seismic 1 0,00 -3,95 0,00 0,00 -1,19
SIS_Y7 seismic 1 0,00 0,00 -5,45 -1,64 0,00
SIS_Z7 seismic 1 2,97 0,00 0,00 0,00 0,00
Soil:
Stresses in soil: σULS = 4.50 (daN/cm2) σSLS = 3.00 (daN/cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 1,40 (m); a = 0,65 (m); B = 1,40 (m); b = 0,65 (m); h1 = 0,30 (m); ex = 0,00 (m);
h2 =0,70(m); ey = 0,00 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 46,0 (cm) b' = 46,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m) (daN*m)
DL1 dead load 1 262,13 0,00 0,00 0,00 0,00
DL2 dead load 1 1000,00 0,00 0,00 0,00 0,00
WIND1 wind 1 0,00 200,00 0,00 0,00 828,00
TEMP1 temperature 1 0,00 0,00 300,00 -1242,00 0,00
SIS_X6 seismic 1 0,00 -81,29 0,00 0,00 -336,57
SIS_Y7 seismic 1 0,00 0,00 -106,80 -442,14 0,00
SIS_Z7 seismic 1 31,04 0,00 0,00 0,00 0,00
Soil:
Stresses in soil: σULS = 4.50 (daN/cm2) σSLS = 3.00 (daN/cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Calculation results:
Real reference level = 17.30 (m)
Stress calculations
Soil type under foundation: not layered
Design combination ELU : 1.00DL+0.90WIND1+1.50TEMP1
Load factors: 1.35 * Foundation weight
1.35 * Soil weight
Calculation results: On the foundation level
Weight of foundation and soil over it: Gr = 5771,13 (daN)
Design load:
Nr = 7033,26 (daN) Mx = -2403,00 (daN*m) My = 961,20 (daN*m)
Equivalent foundation dimensions:
B' = 1 L' = 1
Foundation depth: Dmin = 1,00 (m)
Allowable stress calculation method: Stress pressiometric (SLS), (Fascicule No 62 - Titre V, B.1.)
q SLS = 3.00 (kG/cm2) qu = 8,64 (kG/cm2)
Design soil pressure:
qlim = (qu - q'0) / γf + q'0 = 5.82 (kG/cm2)
γf = 1,50 q'0 = 0,18 (kG/cm2)
Stress in soil: qref = 0.96 (kG/cm2)
Safety factor: qlim / qref = 6.086 > 1
Uplift
Uplift in ULS
Design combination ELU : 1.00DL+0.90WIND1+1.50TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4274,91 (daN)
Design load:
Nr = 5537,04 (daN) Mx = -2403,00 (daN*m) My = 961,20 (daN*m)
Contact area s = 51,96 (%)
slim = 10,00 (%)
Uplift in SLS
Design combination: ELS : 1.00DL
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4274,91 (daN)
Design load:
Nr = 5537,04 (daN) Mx = 0,00 (daN*m) My = 0,00 (daN*m)
Contact area s = 100,00 (%)
slim = 100,00 (%)
Sliding
Design combination ELU : 1.00DL+0.90WIND1+1.50TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4274,91 (daN)
Design load:
Nr = 5537,04 (daN) Mx = -2403,00 (daN*m) My = 961,20 (daN*m)
Equivalent foundation dimensions: A_ = 1,40 (m) B_ = 1,40 (m)
Sliding area: 1,02 (m2)
Cohesion: C = 0.00 (kG/cm2)
Foundation/soil friction coefficient: tg( ) = 0,58
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Column pier:
Longitudinal reinforcement A = 10,67 (cm2) A min. = 10,40 (cm2)
A = 2 * (Asx + Asy)
Asx = 2,60 (cm2) Asy = 2,74 (cm2)
Bottom:
Along X axis: 7 HA 400 12.0
Along Y axis: 7 HA 400 12.0
Top:
Along X axis: 7 HA 400 12.0
Along Y axis: 7 HA 400 12.0
Pier
Longitudinal reinforcement
Along X axis: 10 HA 400 14
Transversal reinforcement 7 HA 400 8
6.4 FOUNDATION TYPE 4
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 0,90 (m); a = 0,45 (m); B = 0,90 (m); b = 0,45 (m); h1 = 0,30 (m); ex = 0,225 (m);
h2 =0,70(m); ey = 0,225 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 35,0 (cm) b' = 35,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m)(daN*m)
DL1 dead load 1 19,92 0,00 0,00 0,00 0,00
DL2 dead load 1 400,00 0,00 0,00 0,00 0,00
WIND1 wind 1 0,00 80,00 0,00 0,00 24,00
TEMP1 temperature 1 0,00 0,00 120,00 -36,00 0,00
SIS_X6 seismic 1 0,00 -3,95 0,00 0,00 -1,19
SIS_Y7 seismic 1 0,00 0,00 -5,45 -1,64 0,00
SIS_Z7 seismic 1 2,97 0,00 0,00 0,00 0,00
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Soil:
Stresses in soil: σULS = 4.50 (daN/cm2) σSLS = 3.00 (daN/cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
ELU : 1.00DL+0.80TEMP1
Mx = -70,14 (daN*m) A'sy = 3,65 (cm2/m)
As min = 0,00 (cm2/m)
Column pier:
Longitudinal reinforcement A = 8,10 (cm2) A min. = 7,20 (cm2)
A = 2 * (Asx + Asy)
Asx = 1,80 (cm2) Asy = 2,25 (cm2)
Bottom:
Along X axis: 4 HA 400 12.0
Along Y axis: 4 HA 400 12.0
Top:
Along X axis: 4 HA 400 12.0
Along Y axis: 4 HA 400 12.0
Pier
Longitudinal reinforcement
Along X axis: 10 HA 400 14
Transversal reinforcement 7 HA 400 8
6.5 FOUNDATION TYPE 5
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 1,00 (m); a = 0,65 (m); B = 1,00 (m); b = 0,65 (m); h1 = 0,30 (m); ex = 0,175 (m);
h2 =0,70(m); ey = 0,175 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 46,0 (cm) b' = 46,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m)(daN*m)
DL1 dead load 1 367,09 -2,85 0,00 0,00 -2,15
DL2 dead load 1 775,47 -35,17 0,00 0,00 -26,46
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Geometry:
A = 2,31 (m) a1 = 0,65 (m) a2 = 0,65 (m) B = 1,00 (m) b1 = 0,65 (m) b2 = 0,65 (m)
h1 = 0,35 (m) e1 = 0,00 (m) h2 = 0,65 (m) e2 = 1,663 (m) ey = 0,00 (m)
h4 = 0,10 (m)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Rotation
About OX axis
Design combination ELU : 1.00DL+1.50TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5381,56 (daN)
Design load:
Nr = 6497,59 (daN) Mx = -1329,93 (daN*m) My = 156,75 (daN*m)
Stability moment: Mstab = 3248,80 (daN*m)
Rotation moment: Mrenv = 1329,93 (daN*m)
Stability for rotation: 2.443 > 1
About OY axis
Design combination: ACC : 1.00DL+0.50WIND1-1.00SIS_X6
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5381,56 (daN)
Design load:
Nr = 5478,79 (daN) Mx = 0,00 (daN*m) My = 2876,18 (daN*m)
Stability moment: Mstab = 6336,22 (daN*m)
Rotation moment: Mrenv = 2876,18 (daN*m)
Stability for rotation: 2.203 > 1
Shear
Design combination ELU : 1.35DL+1.80WIND1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Design load:
Nr = 6888,20 (daN) Mx = 0,00 (daN*m) My = 3631,43 (daN*m)
Length of critical circumference: 1,00 (m)
Shear force: 1450,04 (daN)
Section effective height heff = 0,24 (m)
Shear area: A = 0,24 (m2)
Shear stress: 0,62 (kG/cm2)
Admissible shear stress: 11,90 (kG/cm2)
Safety factor: 19.31 > 1
bottom:
ACC : 1.00DL+1.00SIS_X6
My = 2221,04 (daN*m) Asx = 3,65 (cm2/m)
ELU : 1.35DL1+1.35DL2+1.80WIND1+0.80TEMP1
Mx = 247,64 (daN*m) Asy = 3,65 (cm2/m)
As min = 3,65 (cm2/m)
top:
ACC : 1.00DL+1.00SIS_X6
My = -562,85 (daN*m) A'sx = 3,65 (cm2/m)
ELU : 1.00DL+0.80TEMP1
Mx = -30,25 (daN*m) A'sy = 3,65 (cm2/m)
As min = 0,00 (cm2/m)
Column pier: 1
Longitudinal reinforcement A = 12,55 (cm2) A min. = 10,40 (cm2)
A = 2 * (Asx1 + Asy1)
Asx1 = 3,68 (cm2) Asy1 = 2,60 (cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Column pier: 2
Longitudinal reinforcement A = 11,59 (cm2) A min. = 10,40 (cm2)
A = 2 * (Asx2 + Asy2)
Asx2 = 3,19 (cm2) Asy2 = 2,60 (cm2)
Bottom:
Along X axis: 5 HA 400 12.0
Along Y axis: 11 HA 400 12.0
Top:
Along X axis: 5 HA 400 12.0
Along Y axis: 11 HA 400 12
Pier
Longitudinal reinforcement
Along X axis: 10 HA 400 14
Transversal reinforcement 7 HA 400 8
6.7 FOUNDATION TYPE 7
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 1,587(m) a1 = 0,65 (m) a2 = 0,65 (m) B = 1,40 (m) b1 = 0,65 (m) b2 = 0,65 (m)
h1 = 0,35 (m) e1 = 0,00 (m) h2 = 0,65 (m) e2 = 0,99 (m) ey = 0,937 (m)
h4 = 0,10 (m)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Uplift in SLS
Design combination: ELS : 1.00DL
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5435,56 (daN)
Design load:
Nr = 6621,24 (daN) Mx = 610,84 (daN*m) My = 156,64 (daN*m)
Contact area s = 100,00 (%)
slim = 100,00 (%)
Sliding
Design combination ELU : 1.00DL+1.50WIND1+0.90TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5435,56 (daN)
Design load:
Nr = 6621,24 (daN) Mx = -376,50 (daN*m) My = 2507,44 (daN*m)
Equivalent foundation dimensions: A_ = 1,59 (m) B_ = 1,40 (m)
Sliding area: 1,73 (m2)
Cohesion: C = 0.00 (kG/cm2)
Foundation/soil friction coefficient: tg(φ) = 0,58
Sliding force value F = 488,08 (daN)
Value of force preventing foundation sliding:
- On the foundation level: F(stab) = 3185,64 (daN)
Stabilility for sliding: 6.527 > 1
Rotation
About OX axis
Design combination ELU : 1.00DL+1.50TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5435,56 (daN)
Design load:
Nr = 6621,24 (daN) Mx = -1034,72 (daN*m) My = 156,64 (daN*m)
Stability moment: Mstab = 4654,96 (daN*m)
Rotation moment: Mrenv = 1645,56 (daN*m)
Stability for rotation: 2.829 > 1
About OY axis
Design combination: ELU : 1.00DL+1.50WIND1+0.90TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 5435,56 (daN)
Design load:
Nr = 6621,24 (daN) Mx = -376,50 (daN*m) My = 2507,44 (daN*m)
Stability moment: Mstab = 5263,88 (daN*m)
Rotation moment: Mrenv = 2507,44 (daN*m)
Stability for rotation: 2.099 > 1
Shear
Design combination ELU : 1.00DL1+1.00DL2+1.80WIND1+0.80TEMP1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Design load:
Nr = 6621,24 (daN) Mx = -266,79 (daN*m) My = 2977,60 (daN*m)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Geometry:
A = 1,564 (m) a1 = 0,65 (m) a2 = 0,65 (m) B = 1,30 (m) b1 = 0,65 (m) b2 = 0,65 (m)
h1 = 0,35 (m) e1 = 0,00 (m) h2 = 0,65 (m) e2 = 0,914 (m) ey = 0,00 (m)
h4 = 0,10 (m)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Stress calculations
Soil type under foundation: not layered
Design combinationACC : 1.00DL+0.50WIND1-1.00SIS_X6-1.00SIS_Y7-1.00SIS_Z7
Load factors: 1.35 * Foundation weight
1.35 * Soil weight
Calculation results: On the foundation level
Weight of foundation and soil over it: Gr = 6520,40 (daN)
Design load:
Nr = 5416,60 (daN) Mx = 1727,93 (daN*m) My = 2646,05 (daN*m)
Equivalent foundation dimensions:
B' = 1 L' = 1
Foundation depth: Dmin = 1,00 (m)
Allowable stress calculation method: Stress pressiometric (SLS), (Fascicule No 62 - Titre V, B.1.)
q SLS = 3.00 (kG/cm2) qu = 8,64 (kG/cm2)
Design soil pressure:
qlim = (qu - q'0) / γf + q'0 = 5.82 (kG/cm2)
γf = 1,50 q'0 = 0,18 (kG/cm2)
Stress in soil: qref = 1.60 (kG/cm2)
Safety factor: qlim / qref = 3.639 > 1
Uplift
Uplift in ULS
Design combination ELU : 1.00DL+1.50WIND1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4829,92 (daN)
Design load:
Nr = 6111,40 (daN) Mx = 0,00 (daN*m) My = 1655,79 (daN*m)
Contact area s = 98,03 (%)
slim = 10,00 (%)
Uplift in SLS
Design combination: ELS : 1.00DL
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4829,92 (daN)
Design load:
Nr = 6111,40 (daN) Mx = 0,00 (daN*m) My = 263,19 (daN*m)
Contact area s = 100,00 (%)
slim = 100,00 (%)
Sliding
Design combination ELU : 1.00DL1+1.00DL2+1.50WIND1
Load factors: 1.00 * Foundation weight
1.00 * Soil weight
Weight of foundation and soil over it: Gr = 4829,92 (daN)
Design load:
Nr = 6111,40 (daN) Mx = 0,00 (daN*m) My = 1655,79 (daN*m)
Equivalent foundation dimensions: A_ = 1,56 (m) B_ = 1,30 (m)
Sliding area: 1,99 (m2)
Cohesion: C = 0.00 (kG/cm2)
Foundation/soil friction coefficient: tg(φ) = 0,58
Sliding force value F = 330,00 (daN)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
A = 2 * (Asx1 + Asy1)
Asx1 = 3,26 (cm2) Asy1 = 2,60 (cm2)
Column pier: 2
Longitudinal reinforcement A = 12,22 (cm2) A min. = 10,40 (cm2)
A = 2 * (Asx2 + Asy2)
Asx2 = 2,60 (cm2) Asy2 = 3,51 (cm2)
Bottom:
Along X axis: 6 HA 400 12.0
Along Y axis: 7 HA 400 12.0
Top:
Along X axis: 6 HA 400 12.0
Along Y axis: 7 HA 400 12
Pier
Longitudinal reinforcement
Along X axis: 10 HA 400 14
Transversal reinforcement 7 HA 400 8
6.9 FOUNDATION TYPE 9
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
Geometry:
A = 1,89 (m) a1 = 0,65 (m) a2 = 0,65 (m) B = 1,00 (m) b1 = 0,65 (m) b2 = 0,65 (m)
h1 = 0,35 (m) e1 = 0,00 (m) h2 = 0,65 (m) e2 = 1,24 (m) ey = 0,00 (m)
h4 = 0,10 (m)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Level:
• Cracking : not permissible
• Exposure : severe
• Include element sensitivity condition for fragile failure.
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Geometry:
A = 1,30 (m); a = 0,65 (m); B = 1,70 (m); b = 0,65 (m); h1 = 0,30 (m); ex = 0,00 (m);
h2 =0,70(m); ey = 0,00 (m); h4 = 0, 10 (m) ; c =5,0 (cm)
a' = 46,0 (cm) b' = 46,0 (cm) c1 = 5,0 (cm) c2 = 3,0 (cm)
Foundation loads:
Case Nature Group N Fx Fy Mx My
(daN) (daN) (daN) (daN*m)(daN*m)
DL1 dead load 1 538,87 0,00 0,00 0,00 312,28
DL2 dead load 1 660,00 0,00 0,00 0,00 612,70
WIND1 wind 1 0,00 300,00 0,00 0,00 1192,20
TEMP1 temperature 1 0,00 0,00 210,00 -834,54 0,00
SIS_X6 seismic 1 37,05 -252,69 0,00 0,00 -665,98
SIS_Y7 seismic 1 0,00 0,00 -105,40 -413,94 0,00
SIS_Z7 seismic 1 74,91 -25,93 0,00 0,00 -172,02
Soil:
Stresses in soil: σULS = 4.50 (daN/cm2) σSLS = 3.00 (daN/cm2)
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.
Company document Contractor doc. Valid. Sheet of
Revision
ETAP identification identification Status Sheets
Column pier:
Longitudinal reinforcement A = 12,82 (cm2) A min. = 10,40 (cm2)
A = 2 * (Asx + Asy)
Asx = 3,81 (cm2) Asy = 2,60 (cm2)
Bottom:
Along X axis: 6 HA 400 12.0
Along Y axis: 8 HA 400 12.0
Top:
Along X axis: 6 HA 400 12.0
Along Y axis: 8 HA 400 12
Pier
Longitudinal reinforcement
Along X axis: 10 HA 400 14
Transversal reinforcement 7 HA 400 8
This document is property of Eni Tunisia B.V. who will safeguard its rights according to the civil and penal provision of the law.