Professional Documents
Culture Documents
Jaw Crusher Capacity and Gradations
Jaw Crusher Capacity and Gradations
* Above capacities based on free-flowing, friable material with approximately 100#/cu. ft. density.
McLanahan-Universal Jaw Crusher sizes are determined by the model numbers, the first two numbers being the measurement in inches from the top of the crown on the stationary jaw plate to the top of the crown
on the movable jaw plate, and the last two numbers being the width between the side liners. Example: A model 2036 has an opening of 20" from the top crown of the stationary jaw plate to the top of the movable
jaw plate and has a measurement of 36" between the side liners.
These capacity and gradation charts are based on a discharge gap which is measured from peak-to-peak on the corrugated jaw dies.
McLanahan-Universal Jaw Crushers are known for their efficiency and aggressive crushing action. The capacities and output gradations provided here in are
theoretical in nature, and will vary with each and every application due to material characteristics and numerous other factors. These charts serve as a guide only.
McLANAHAN-UNIVERSAL JAW CRUSHER
Traditional Hydraulic-Shim and H-Series Crushers
mclanahan.com
2-3/4 100 96 90 84 80 69 62 54 46 37 31 25 20 17
2-1/2 100 96 90 85 80 71 64 56 49 42 34 28 23 18 16
2-1/4 100 96 90 85 78 72 65 58 52 46 39 31 26 21 16 15
2 100 95 90 84 78 72 65 58 52 47 41 35 27 23 19 14 14
1-3/4 94 89 84 78 71 64 58 52 46 41 35 30 24 20 17 13 13
1-1/2 100 88 82 78 71 63 57 51 46 40 35 30 26 22 18 15 12 12
1-1/4 93 82 75 70 62 55 50 45 40 34 30 26 23 19 16 13 11 11
1 100 87 75 67 61 52 46 41 37 33 29 26 23 20 17 14 12 10 10
7/8 96 81 68 59 51 46 41 36 32 28 25 23 20 17 15 12 11 9 9
3/4 90 75 59 52 44 39 35 31 28 25 22 20 17 15 13 11 8 8 8
5/8 85 69 51 45 38 33 29 26 24 21 18 17 14 13 11 9 7 7 7
1/2 78 60 45 37 30 27 24 22 20 17 15 14 12 11 9 8 6 6 6
3/8 72 44 34 29 23 21 18 16 15 12 11 10 8 8 7 6 5 5 5
5/16 66 34 29 25 19 17 15 13 12 10 9 8 7 7 6 5 4 4 4
1/4 45 29 24 20 16 14 12 10 9 8 7 6 6 6 5 4 3 3 3
4M 27 22 19 16 12 10 9 7 6 5 4 4 4 4 3 3 2 2 2
8M 14 13 12 10 7 7 6 5 4 3 3 3 3 3 2 2 1 1 1
General Specifications
Model 1024 1036 1236 1248 1260 1524 1536 1824 1830 2236 2248 2540 3242 3254 3260 3264 4250 4848 5060 6684
Eccentric Shaft Diameter at Center 7" 8.75" 8.75" 9.25" 11" 8.75" 9.25" 8.75" 9.25" 9.75" 11" 10.5" 13.375" 13.375" 14.125" 13.375" 14.125" 17.25" 17.25" 23.5"
Eccentric Shaft Throw 1" 1" 1" 1" 1" 1.25" 1.25" 1.25" 1.25" 1.25" 1.5" 1.25" 1.5" 1.5" 1.5" 1.5" 1.5" 1.5" 1.5" 1.5"
Pitman Bearings 150 190 190 200 220 190 200 190 200 220 260 240 300 300 320 300 320 400 460 530
Side Bearings 120 160 160 180 200 160 180 160 180 200 240 220 300 300 320 300 320 360 360 500
Max Closed Side Setting 3" 3" 3" 4" 3" 4" 4" 4" 4" 6" 8" 6" 10" 11" 10" 8" 14" 11" 14" 18"
Min Closed Side Setting .25" .25" .25" .25" .25" .75" .75" .75" .75" 1.5" 2" 2" 3" 3" 3" 3" 3" 3" 4" 6"