Professional Documents
Culture Documents
MIS 6314 Long Quiz 3
MIS 6314 Long Quiz 3
1. Dashboard
2. My courses
3. MIS6314
4. Week 9: Long Quiz
5. Long Quiz 003
Question 1
Correct
Flag question
Question text
The ABC Mining company network administrator has been asked to summarize the routes for a new OSPF
area. The networks to be summarized are 172.16.8.0, 172.16.10.0, and 172.16.12.0 with subnet masks of
255.255.255.0 for each network. Which command should the administrator use to forward the summary
route for area 15 into area 0?
Select one:
Question 2
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A network administrator is implementing OSPF in a portion of the network and must ensure that only
specific routes are advertised via OSPF. Which network statement would configure the OSPF process for
networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now located in the backbone area, and
inject them into the OSPF domain?
Select one:
c. c
Question 3
Correct
Question text
In scaling networks what command pertains to propagating a default route?
Select one:
Question 4
Correct
Mark 0.00 out of 1.00
Flag question
Question text
As discussed in link state advertisement which two statements correctly describe OSPF type 3 LSAs?
Select one:
c.1 & 5
Question 5
Correct
Flag question
Question text
In OSPF configuration understanding which parameter would you tune to affect the selection of a static
route as a backup, when a dynamic protocol is also being used?
Select one:
c.administrative distance
Question 6
Correct
Flag question
Question text
In verifying multiarea OSPF which command can be used to verify the contents of the LSDB in an OSPF
area?
Select one:
Question 7
Correct
Flag question
Question text
Observe the above exhibit carefully. The ADS MusicStudio network administrator is trying to configure R1
to run OSPFv3 but the neighbor adjacency is not forming with the router connected to Fa0/0. What is the
cause of the problem?
Select one:
Question 8
Correct
Flag question
Question text
As discussed in most OSPF topics what does an O E1 or E2 routing table entry mean?
Select one:
a.External route
Question 9
Correct
Flag question
Question text
In RMS University, the network admin is trying to add a new router into an established OSPF network. The
network attached to the new router do not appear in the routing tables of the other OSPF routers. Given
the information in the partial configuration shown below, what configuration error is causing this
problem?
Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0
Select one:
Question 10
Correct
Flag question
Question text
A certified network administrator of Gilas Medical Hospital has just changed the router ID on a router that
is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use
the new router ID?
Select one:
.
Question 11
Correct
Flag question
Question text
Which 3 features are OSPF routing protocol?
Select one:
b.Converge quickly, Identify the best route by the use of cost & before exchanging routing
information, OSPF routers find out neighbors.
Question 12
Correct
Flag question
Question text
In single-area OSPF concepts which parameter would you tune to affect the selection of a static route as a
backup, when a dynamic protocol is also being used?
Select one:
c.administrative distance
Question 13
Correct
Flag question
Question text
A certified network administrator of RMS Company has just changed the router ID on a router that is
working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use
the new router ID?
Select one:
Question 14
Correct
Flag question
Question text
Refer to the exhibit shown. What command statement must be issued to complete the configuration at R1
for multiarea OSPF.
Select one:
Question 15
Correct
Flag question
Question text
A network administrator of an international herbal company is verifying a multi-area OSPF configuration
by checking the routing table on a router in area 1. The administrator notices a route to a network that is
connected to a router in area 2. Which code appears in front of this route in the routing table within area
1?
Select one:
d.O IA
Question 16
Correct
Question text
Refer to the series of ip addresses below. A network specialist has been asked to summarize the networks
shown in the exhibit as part of a multiarea OSPF implementation. All addresses are using a subnet mask of
255.255.255.0. What is the correct summarization for these eight networks?
10.0.4.0 10.0.8.0 10.0.5.0 10.0.9.0
10.0.6.0 10.0.10.0 10.0.7.0 10.0.11.0
Select one:
d.10.0.0.0 255.255.240.0
Question 17
Correct
Flag question
Question text
What are the building blocks of OSPF?
Select one:
Question 18
Correct
Flag question
Question text
What does an O routing table entry mean?
Select one:
c.Intra-area route
Question 19
Correct
Flag question
Question text
An ASBR generates what type of LSAs for each of its external routes and floods them into the area that it is
connected to.
Select one:
d.Type 5
Question 20
Correct
Flag question
Question text
Why do OSPF serial interfaces usually require manual bandwidth configuration?
Select one:
c.OSPF uses the bandwidth value to compute routes for its routing table.
Question 21
Correct
Flag question
Question text
What routerhas all of its interfaces in the same area and have identical LSDBs.
Select one:
a.Internal Router
Question 22
Correct
Flag question
Question text
Observe the exhibit shown above. These two routers are configured to run OSPFv3 but they are not
forming a neighbor adjacency. What is the cause of the problem?
Select one:
Question 23
Correct
Flag question
Question text
As discussed in scaling networks what type of OSPF LSA is originated by ASBR routers to advertise external
routes?
Select one:
d.type 5
Question 24
Correct
Flag question
Question text
When OSPFv2 neighbors are establishing adjacencies, in which state do they elect a DR and BDR router?
Select one:
d.Two-Way state
Question 25
Correct
Flag question
Question text
What happens when a router has two network statements in different areas?
Select one:
Question 26
Correct
Flag question
Question text
The network engineer of Stark Industries has manually configured the hello interval to 15 seconds on an
interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be
affected?
Select one:
Question 27
Correct
Flag question
Question text
What happens when a router has two network statements in different areas?
Select one:
Question 28
Correct
Flag question
Question text
Which command statement below will a network engineer issue to verify the configured hello and dead
timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?
Select one:
Question 29
Correct
Flag question
Question text
Which of these works better for larger networks?
Select one:
b.Multi-area OSPF
Question 30
Correct
Question text
In OSPF networks discussion what router that has at least one interface that is attached to a non-OSPF
network?
Select one:
a.ASBR