Professional Documents
Culture Documents
ER TFTM070 4 Datasheet
ER TFTM070 4 Datasheet
b
u
y
-
d
i
s
p
l
a
y
.
c
o
m
EA
0B
1B ER-TFTM070-4
2B TFT Display Datasheet
Attention:
4B
A. Some specifications of IC are not listed in this manual. Please refer to the IC datasheet for more details.
B. The drawing for related schematic drawing, demo code is all available, please download from our web.
C. Please pay more attention to “INSPECTION CRITERIA” in this manual. We assume you already agree with these criterions when you place an
REV
8B3 DESCRIPTION
9B4 RELEASE DATE
10B5
1.0
1B6 Preliminary Release
12B7 Mar-19-2013
13B
14B937
CONTENTS
15B0H
21B8HU 2. ATTRIBUTES - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06 U
4.2 Pin Configuration –JP1 ( I/O Port in Pin1~Pin3) / Flash Interface in Pin4~Pin8) - - - - - - - - - - - - - 09
23B015H H
38B54H
1. ORDERING INFORMATION
54B197
1.2 Optional Accessory List (We give customer’s more freedom to build your own display)
Attention: The accessory you select would be mounted on board by default except flash memory chip.
67B1584No Accessory for Parallel Interface Qty Position on Board
ZIF connector in 40 pins(1 piece is soldered on board, the another is used
1 2 CON1
on customer’s board)
FFC in 40 pins, 100mm length,1.00mm pitch used to connect display with
2 1 CON1
customer’s board
67B1584No Accessory for MicroSD Card Interface Qty Position on Board
9 Flash Memory Chip from 32M~128M bit (Not mounting on board by default) 1 U1
1.3 Image
58B214039
2. ATTRIBUTES
2.1 Display Attributes
40B59376
Display Connector
6B308 FFC or Pin Header
67B419 --
68B5270
FPC Connector
69B3 40/8 Pins,1.0mm Pitch, SMD Horizontal Type Top contact --
Operating Temperature
70B648 -20 ~ +70
71B685
℃
72B698
Storage Temperature
73B0689 -30 ~ +80
74B16890
75B2691 ℃
Touch Panel Optional Yes 81B75 --
Sunlight Readable
82B796 83B07 No --
84B17
ITEM
86B30 STANDARD VALUE
87B41 UNIT
8B52
Diagonal Size
89B63 7.0 91B85 inch
Outline Dimension(PCB) 180.0 x 104.0 mm
Active Area
92B86 154.08 x 85.92 mm
93B087
Dot Pitch
9B63 0.0642(W) x 0.1790(H) mm mm 10B985
Net Weight
102B96 180
103B97 g
104B98
IC Package
109B637 SMT
10B742 --
1B085
Controller
12B0967 SSD1963
13B072 --
14B08
Interface
15B209 8080/6800,8-bit/9-bit/16-bit/18-bit/24-bit Parallel
96B --
17B4
ITEM
19B63 STANDARD VALUE
120B74 UNIT
12B85
LCD Type
12B9653 TFT-LCD / Transmissive / Negative
123B0754 --
124B85
Colors
13B2856 65K/262K/16.7M
132B9 --
13B02758
PCB 180.00±0.3
M.H 174.00±0.1
7.55±0.3 BEZEL 164.90±0.3
0.1
JP1 .00±
7 8
8-? 1
31.50±0.3
7.62
10.16
1 2
JP2
39 40
40
7 " TFT
W 0.70±0.1
±0.1
1.00
BEZEL 100.00±0.3
40-?
PCB 104.00±0.3
A,A 85.92±0
M.H 98.00±0.1
800RGB X 480
V,A 89.00
48.26
41.00
P 1.00±0.05
39.00
1.70
6 O'CLOCK 2.00
1
10.16
1 2
10.09±0.3
1.50 4.00
2.54
7.62
8-?
1.0
0 ±0
.1
9.50±0.3
11.04±0.3
2.00±0.3
4-
4-? 4
?
MAX 10.0
5.30±0.3
0.33±0.05
CONDUCTOR
STIFFENER
JP1 U1 L2
C1
8 7 D1 C3 J8
J1
J2
J5
FLASH C2 U2 J9
R1 J6
BL PWM J3
FFC is used for parallel 2 1 BL ON/OFF J4 L1
C42
interface,it's optional. JP2
40 39 C4 C5 CON4 40P05
7
C
40
C8 C9 U3
C34 J7 C35
C33 C36
C10
C32 R6
C31 C37 7 INCH TFT LCD
C12
C13 C30 C38
U6 C39
C14 C29 C40
C15 C28 C41
R10
R7
CON1
C16
40P1
C27
R3
R2 C19 C25 CON3
C21
C17 C18 C26 4P1
R4 C20 C24
8080 R3 ON R4 NC
C22
6800 R4 ON R3 NC X1
C23 R5
R53
C49
6.00±0.5 2 1
L3
J10
JP3 U5 C47
8
8 7
8P1
R11
CON2
R19
R20
R18
2 1 L4
1
R17
FFC is used for MicroSD
Card interface,it's optional.
BACK
CD
EastRising Technology Co.,Ltd
UNIT: MM SIZE: A4
EastRising 旭日东方科技有限公司
b
u
y
-
d
i
s
p
l
a
y
.
c
o
m
SHEET: 1 OF 1
Pin No Symbol
140B37 14B385 142B396
145B239 Descriptions
1
146B30 VSS
147B Ground
2
149B63 VDD Power Supply
3
15B249 /CS
156B30
Chip Select, Active Low
4
16B58 D/C
162B59
Data/Command Select
1:Read cycle
8080 mode:WR#(write strobe signal)
7
176B30 /RESET_NC
E Master synchronize reset,Active Low
8 TE Tearing effect
9-32
180B74 DB0-DB23
18B75 Data bus. Pins not used should be floating
183B07
4.2 Pin Configuration –JP1 ( I/O Port in Pin1~Pin3) / Flash Interface in Pin4~Pin8)
Pin No
140B37 14B385 Symbol
142B396 Description
145B239
1
146B30 GPIO1
These pins can be configured for display miscellaneous signals
2
149B63 GPIO2
or as general purpose I/O. Default as input.
3 GPIO3
4 FLASH_DIO NC Data Input / Output
5 FLASH_CLK NC Serial Clock Input
6 FLASH_/WP NC Write Protect Input
7 FLASH_DO NC Data Output
8 FLASH_/CS NC Chip Select Input
IDD(3.3V) -- -- 480 mA
Model Current
IDD(5.0V) -- -- 300 mA
286B3094
5. INSPECTION CRITERIA
5.1 Acceptable Quality Level
H287B4130
PARTITION
289B63 290B874 AQL 291B85 DEFINITION
A. Major
29B86 0.4%
293B087 Functional defective as product
294B18
B. Minor
295B8 1.5%
296B30 Satisfy all functions as product but not satisfy cosmetic stanard
297B41
◆ INSPECTION CONDITION
305B29
314B
h H
4 Scratch In accordance with spots and lines operating cosmetic criteria, When the Minor
light reflects on the panel surface, the scratches are not to be remarkable.
5 Allowable density Above defects should be separated more than 30mm each other. Minor
6 Coloration Not to be noticeable coloration in the viewing area of the LCD panels. Minor
Back-lit type should be judged with back-lit on state only.
7 Contamination Not to be noticeable. Minor
L 5.0 (0)
8
L 10.0 (0)
8
(6)
Note:
(1) Size : d=(long length + short length)/2
(2) The limit samples for each item have priority.
(3) Complexed defects are defined item by item, but if the number of defects is defined in above table, the total
number should not exceed 10.
(4) In case of ‘concentration’, even the spots or the lines of ‘disregarded’ size should not be allowed. Following three
situations
Should be treated as ‘concentration’.
-7 or over defects in circle of ¢5mm.
-10 or over defects in circle of ¢10mm
-20 or over defects in circle of ¢20mm
◆ This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions.
321B85
◆ EastRising display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact.
32B196
◆ If EastRising display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in
32B017
your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
◆ Do not apply excessive force to the EastRising display surface or the adjoining areas since this may cause
324B18
dry cloth. If it is heavily contaminated, moisten cloth with one of the following Isopropyl or alcohol.
◆ Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the Water.
327B41
◆ Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water
328B5
sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the cable or the
backlight cable.
◆ Do not attempt to disassemble or process EastRising LCD module.
30B274
◆ If the logic circuit power is off, do not apply the input signals.
32B96
◆ To prevent destruction of the elements by static electricity, be careful to maintain an optimum work
3B027
environment.
-Be sure to ground the body when handling EastRising LCD modules.
34B128
-Tools required for assembling, such as soldering irons, must be properly grounded.
35B29
-To reduce the amount of static electricity generated, do not conduct assembling and other work under dry
36B0
conditions.
-The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this
37B41
◆ Use a clean power source free from transients. Power-up conditions are occasionally jolting and may
341B85
display. Don’t allow the data bus to be driven when the logic supply to the module is turned off.
43B0752198
◆ DO NOT plug or unplug EastRising module when the system is powered up.
345B29
◆ Minimize the cable length between EastRising module and host MPU.
346B0
◆ For models with backlights, do not disable the backlight by interrupting the HV line. Unload inverters
347B1
produce voltage extremes that may arc within a cable or at the display.
◆ Operate EastRising module within the limits of the modules temperature specifications.
348B52
◆ Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended
350B47
as they may seep under the electrometric connection and cause display failure.
351B48
◆ Mount EastRising module so that it is free from torque and mechanical stress.
352B496
◆ Surface of the LCD panel should not be touched or scratched. The display front surface is an easily
35B047
scratched, plastic polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton
dampened with petroleum benzene.
◆ Always employ anti-static procedure while handling EastRising module.
354B18
◆ Prevent moisture build-up upon the module and observe the environmental constraints for storage tem
35B249
◆ If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion.
357B41
If the body or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and
soap
468B352
When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps.
359B6
Keep EastRising modules in bags (avoid high temperature / high humidity and low temperatures below 0C
360B574
Whenever possible, EastRising LCD modules should be stored in the same conditions in which they were
361B58
Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective
36B057
orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module
is subject to a low temperature.
If EastRising LCD modules have been operating for a long time showing the same display patterns, the
364B158
display patterns may remain on the screen as ghost images and a slight contrast irregularity may also
appear. A normal operating status can be regained by suspending use for some time. It should be noted that
this phenomenon does not adversely affect performance reliability.
To minimize the performance degradation of the LCD modules resulting from destruction caused by static
365B29
electricity etc., exercise care to avoid holding the following sections when handling the modules.
-Exposed area of the printed circuit board.
36B0
69B3845 362B
EastRising LCD is composed of glass and polarizer. Pay attention to the following items when handling.
370B64
◆ Please keep the temperature within specified range for use and storage. Polarization degradation, bubble
371B685
generation or polarizer peel-off may occur with high temperature and high humidity.
◆ Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass,
372B69
tweezers, etc.).
◆ N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors
37B06
made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and
isopropylalcohol.
◆ When EastRising display surface becomes dusty, wipe gently with absorbent cotton or other soft material
374B168
like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.
◆ Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
375B269
◆ Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers.
378B52
After products are tested at low temperature they must be warmed up in a container before coming is
contacting with room temperature air.
◆ Do not put or attach anything on EastRising display area to avoid leaving marks on.
379B6
◆ Do not touch the display with bare hands. This will stain the display area and degradate insulation
380B74
◆ As glass is fragile. It tends to become or chipped during handling especially on the edges. Please
382B796
◆ Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
384B17259
◆When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting
386B0
plate should have enough height to avoid causing stress to the module surface, refer to the individual
387B41
◆ Do not alter, modify or change the shape of the tab on the metal frame.
390B874
◆ Do not make extra holes on the printed circuit board, modify its shape or change the positions of
391B85
components to be attached.
◆ Do not damage or modify the pattern writing on the printed circuit board.
392B86
◆ Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
39B087
◆ Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
394B18
Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as
397B41
◆ Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body
39B6
◆ When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to
401B3985
minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the
commutator of the motor.
◆ As far as possible make the electric potential of your work clothes and that of the work bench the ground
402B396
potential.
◆ To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative
403B97
If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This
409B63
does not apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD
surface with a cover during soldering to prevent any damage due to flux spatters.
◆ When soldering the electroluminescent panel and PC board, the panel and board should not be detached
410B7
more than three times. This maximum number is determined by the temperature and time conditions
mentioned above, though there may be some variance depending on the temperature of the soldering iron.
◆ When remove the electroluminescent panel from the PC board, be sure the solder has completely melted,
41B085
463B120957
◆ Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best
413B07
contrast.
◆ Driving the EastRising LCD in the voltage above the limit shortens its life.
41B08
◆ Response time is greatly delayed at temperature below the operating temperature range. However, this
415B209
does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature
range.
◆ If EastRising display area is pushed hard during operation, the display will become abnormal. However, it
416B30
Unless agreed between EastRising and customer, EastRising will replace or repair any of its LCD modules
49B163 420B17
which are found to be functionally defective when inspected in accordance with EastRising LCD acceptance
standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual
defects must be returned to EastRising within 90 days of shipment. Confirmation of such date shall be based
on freight documents. The warranty liability of EastRising limited to repair and/or replacement on the terms set
forth above. EastRising will not be responsible for any subsequent or consequential events.
7.7 Return Policy
No warranty can be granted if the precautions stated above have been disregarded. The typical examples of
2B4196
violations are:
-Broken LCD glass. 423B017
Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with
429B63
sufficient description of the failures or defects. Any connectors or cable installed by the customer must be
removed completely without damaging the PCB eyelet’s, conductors and terminals
430B275