Professional Documents
Culture Documents
As 1418.03-1997 Cranes Hoists and Winches - Bridge Gantry and - Portal Cranes (Including Container Cranes) and J
As 1418.03-1997 Cranes Hoists and Winches - Bridge Gantry and - Portal Cranes (Including Container Cranes) and J
As 1418.03-1997 Cranes Hoists and Winches - Bridge Gantry and - Portal Cranes (Including Container Cranes) and J
for
AS 1418.3-1997 Cranes, hoists and winches - Bridge, gantry and portal cranes (including container cranes) and jib cranes
<p>Licence Agreement This is an agreement between the end user of the Product ("Licensee") and SAI Global
Limited, 286 Sussex Street, Sydney NSW 2000 AUSTRALIA, ABN 67 050 611 642. 1. Definitions and Interpretations Australian
Standards means Australian Standards and includes Joint ISO/Australian Standards, Joint NZ/Australian Standards, current
Draft Australian Standards, and amendments to Australian Standards. Concurrent Users means the maximum number of people
able to access the Product at any one time, and is limited to the number of Licences purchased. ISO Standards means
Standards published by the International Organization for Standardization (ISO), for which SAI Global is an authorised distributor.
IEC Standards means Standards published by the International Electrotechnical Commission (IEC), for which SAI Global is an
authorised distributor. Internal use means use of the Product within the Licensee’s organization. Licence means the right
to access and use the Product. Licensee means the purchaser and user of the Product. Product means Australian Standards,
ISO Standards and IEC Standards ordered and purchased through the InfoStore, and downloaded as electronic PDF files. 2.
Product Availability 2.1. The Product is available via the World Wide Web through the use of a web browser. Documents are
provided as PDF files, viewable through the use of Adobe ® Acrobat ® Reader Version 7 and above. 3. Licence
Agreement 3.1. By using the Product the Licensee agrees to be bound by the Licence Agreement for the Product. 3.2. The
Licensee is granted a non-exclusive and non-assignable Licence to use the Product. 3.3. Licensees are permitted to use the
Product the following extent: 3.3.a. Purchasers of personal user Licences for the Product may locally install and use the Product
on the number of individual computers corresponding to the number of personal users specified in the SAI Global InfoStore
order. Licensees are permitted to make paper copies of the Product for Internal use limited to the number of personal users
specified in the SAI Global InfoStore order only ( excludes electronic pads of forms ). Licensees are permitted to make one
electronic copy of the Product for backup purposes. 3.3.b. Purchasers of network Licences for the Product may install and use
the Product on a network with the number of Concurrent Users permitted corresponding to the number of users specified in the
SAI Global InfoStore order. Licensees are permitted to make paper copies of the Product for Internal use limited to the number of
network users specified in the SAI Global InfoStore order only. Licensees are permitted to make one electronic copy of the
Product for backup purposes. 3.4. SAI Global will not in any way provide the Licensee with an updating service for the Product.
The Licensee agrees that SAI Global has no obligation whatsoever to advise you of any amendments or changes to the Product
or even as to its withdrawal from publication irrespective of the reason for any such amendment, change or withdrawal. 3.5. It is
expressly agreed that the Standards Australia retains all title to the intellectual property contained in the Product or is an
authorized distributor of the intellectual property. Licensees shall not challenge or call into question Standards Australia's
ownership of Intellectual Property Rights in respect of the Product. 3.6. The electronic PDF files provided by the Product, and
authorized paper copies of the Product, are the subject of copyright. Unauthorized copying of the Product and any modification of
or merger with other software or documents is expressly forbidden. However, in consideration for entering into this licence
agreement and agreeing to pay theonLicence
Click the red fees to SAItoGlobal,
box above activate the
theLicensee
Licence may use the
Agreement Product
scroll bar. to obtain information
contained in the electronic PDF files for their own Internal use only but shall not otherwise use, modify, copy, adapt, supply,
WEB LINKS
transmit, send by e-mail, reproduce, or do any other thing in relation to, the Product. The Product may not be copied or circulated
electronically, including by electronic mail, even for Internal use. 3.7. The Licensee shall not modify, adapt, translate, reverse
engineer, decompile, disassemble or create derivative works based on the Product. 3.8. The Licensee shall ensure that all of the
personal users that have rights to access the Product under this Licence shall exercise that right only for the purposes specified
and shall not use the Product for any other purpose. 3.9. For reproduction of the Product or portions of the Product, and for which
are outside the circumstances included in this Check agreement,
if thispermission
document mustisbe sought in writing from SAI Global, Copyright
current
Officer. 3.10. The Product is Licensed only to the Licensee. Under no circumstances may the Product be transferred by the
Licensee to any other party without the prior Findwritten consent
similar of SAI Global. Under no circumstances is the Licensee permitted to
documents
reproduce material from the Product for external use or for use on any other site or group of sites. 3.11. This Licence will
terminate automatically and without notice Visit our website
if the Licensee fails to comply with any provision of the Licence. Upon termination the
Licensee agrees to destroy all copies of the Product. 3.12. The Licensee acknowledges that no promise, representation,
warranty or undertaking (other than any contained in this Agreement) has been given by SAI Global or any person or company
on its behalf in relation to the profitability of or any other consequences or benefits to be obtained from the use of the Product
and the Licensee relies wholly upon International
his own skill Standards on-line
and judgment in at infostore.saiglobal.com/store
deciding to use the Product. 3.13. SAI Global shall not be liable
to the Licensee or any other person in respect of any loss or damage, however caused which may be suffered or incurred or
which may arise directly or indirectly in respect to the Product. 3.14. No warranty is made by any party connected with this
Product, express or implied, with regard to the quality, utility or accuracy of the Product and no liability will be accepted for any
damage, direct, indirect, special or consequential, arising in any way out of the use of the Product. This agreement is governed
by and must be construed in accordance with the laws of the State of New South Wales. For further information and technical
support contact: In USA and Canada Contact:- SAI Global, 610 Winters Avenue, Paramus, NJ 07652, USA • Toll Free
1-888-454-2688 or 201-986-1131 • Fax: 201-986-7886 • E-mail: uspubsales@saiglobal.com • Web:
AS 1418.3—1997
(Incorporating Amendment Nos 1 and 2)
AS 1418.3
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
Australian Standard™
Australian Standard™
COPYRIGHT
© Standards Australia International
All rights are reserved. No part of this work may be reproduced or copied in any form or by any
means, electronic or mechanical, including photocopying, without the written permission of the
publisher.
Published by Standards Australia International Ltd
GPO Box 5420, Sydney, NSW 2001, Australia
ISBN 0 7337 1527 3
AS 1418.3—1997 2
PREFACE
This edition of this Standard was prepared by the Joint Standards Australia/Standards
New Zealand Committee ME/5, Cranes, to supersede AS 1418.3—1990.
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
CONTENTS
Page
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
SECTION 3 STRUCTURE
3.1 BASIS OF DESIGN..................................................................................................... 7
3.2 SLENDERNESS RATIOS OF BRIDGE SECTION .................................................... 7
3.3 DEFLECTION............................................................................................................. 7
3.4 SPAN TO WHEELBASE RATIO ............................................................................... 8
SECTION 4 STABILITY......................................................................................................... 8
SECTION 8 CLEARANCES
8.1 HANDRAIL CLEARANCES .................................................................................... 20
8.2 CLEARANCE ABOVE CRANE OR CRAB ............................................................. 20
8.3 CLEARANCE BELOW UNLADEN CRANE WITH POWER-DRIVEN
TRAVEL OR TRAVERSE MOTION........................................................................ 20
8.4 CLEARANCES BETWEEN CRANE AND PLATFORMS....................................... 20
8.5 CLEARANCE AT OR NEAR A CRANE RUNWAY ............................................... 21
8.6 CLEARANCE BETWEEN MOVING PARTS OF A CRANE AND A
PLATFORM OR WALKWAY.................................................................................. 21
AS 1418.3—1997 4
Page
8.7 CLEARANCES BETWEEN HOIST UNIT AND CRANE END CARRIAGE
OR RUNWAY ........................................................................................................... 21
9.1 GENERAL................................................................................................................. 22
9.2 ACCESS ISOLATORS FOR ACCESS FROM FIXED PLATFORMS ..................... 22
9.3 ACCESS ISOLATORS FOR ACCESS FROM MOBILE PLATFORMS .................. 22
9.4 MARKING OF ACCESS ISOLATORS .................................................................... 23
SECTION 13 GUARDING
13.1 GENERAL................................................................................................................. 30
13.2 STRENGTH .............................................................................................................. 30
13.3 MATERIAL............................................................................................................... 30
13.4 FIXED GUARDS ...................................................................................................... 30
13.5 REMOVABLE GUARDS.......................................................................................... 30
13.6 INSPECTION POINTS ............................................................................................. 30
13.7 MARKING ................................................................................................................ 30
13.8 TRAVEL MOTION WHEELS .................................................................................. 30
13.9 COLOUR................................................................................................................... 30
APPENDICES
A INFORMATION TO BE SUPPLIED WITH ENQUIRY, ORDER, OR TENDER .... 31
B LIST OF TYPICAL HAZARDS ................................................................................ 36
C ACCESS AND CLEARANCE REQUIREMENTS FOR FIXED PLATFORMS....... 38
A1 D TYPICAL CRANE DRIVE DIAGRAMS.................................................................. 24
5 AS 1418.3—1997
STANDARDS AUSTRALIA
Australian Standard
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
A2
Cranes, hoists and winches
Part 3: Bridge, gantry, portal (including container cranes) and jib cranes
1.1 SCOPE
This Standard sets out requirements for bridge, gantry, semi-gantry, and portal cranes
defined in AS 2549. It also covers container and heavy-duty cranes.
It is complementary to AS 1418.1, but the requirements given herein take precedence over
corresponding requirements in that Standard.
NOTES:
1 Guidance on information to be supplied with enquiry, order, or tender is given in
Appendix A.
2 Additional requirement for heavy duty cranes are given in AS 1418.14.
1.3 APPLICATION
Cranes using fixed platforms for servicing shall comply with Sections 1 to 6 and 8 to 13
inclusive. Cranes using mobile platforms for servicing shall comply with Sections 1 to 5
and 7 to 13 inclusive.
NOTE: Throughout this Standard the ‘servicing’ implies routine servicing only (i.e. does not
include crane breakdowns).
AS
1892 Portable ladders
1892.2 Part 2: Timber
2321 Short-link chain for lifting purposes (non-calibrated)
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
1.5 DEFINITIONS
For the purpose of this Standard, the definitions given in AS 2549 and that below apply.
1.5.1 Container crane
Rail-mounted crane equipped with a spreader assembly for engaging and lifting freight
containers.
1.6 SAFETY
The design of bridge, gantry and portal cranes in relation to materials, construction and
equipment shall eliminate as far as practicable the potential hazards associated with all
specified operating conditions.
NOTES:
1 Examples of potential hazards associated with bridge, gantry and portal cranes are given in
Appendix B.
2 General guidance on the safe use of cranes is given in AS 2550.1.
S E C T ION 3 S T R UC T UR E
3.3 DEFLECTION
3.3.1 Limits
The limits of vertical static deflection and lateral deflection shall be as specified in
AS 1418.1.
For semi-portal cranes, the vertical static deflection of the crane bridge of 1/500 span, as
specified in AS 1418.1, is acceptable only if precautions are taken for the kick-out of the
leg.
NOTE: Subject to the client’s approval, the deflection for cranes greater than 30 m span may
exceed the 60 mm requirement to a limit of L/500 providing due consideration is taken of the
effects on the function of the crane.
3.3.2 Leg spread of gantry cranes
The design shall be such that the load shall not induce binding of wheel flanges on the rails.
3.3.3 Natural frequency
The natural frequency shall be equal to or greater than 2.4 Hz—
A2 (a) The vibration frequency of the crane structure, in any horizontal direction, shall be
not less than 2.4 Hz. The vibration frequency shall be calculated using the higher of
the lateral deflection values calculated according to AS 1418.1.
For cranes equipped with an operator’s cabin, the limits of vibration amplitude at the
centre of gravity of the cabin are dependent on the sustained frequency of vibrations
and the design shall be in accordance with AS 2670.
The vibration frequency in the first mode of vibration of a flexural element shall be
calculated in a rational manner.
A2 For a girder, the following simplified equation for fundamental natural frequency may
be used:
16
f= . . . 3.3.3(a)
δ
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
where
F = natural frequency, in hertz
δ = vertical (or horizontal) deflection, in millimetres
In the above equation, the value of δ for cantilever cranes shall include the flexure of
the boom and the support posts.
(b) due to torsional vibration of the bridge structure.
3.3.4 Lateral forces on portal cranes
Lateral forces on portal cranes due to oblique travel may be disregarded where the structure
has sufficient inherent flexibility to prevent any effective transfer of such loads through the
structure; however, lateral forces due to inertia shall be taken into account.
3.3.5 Camber
Camber is not necessary to maintain serviceability.
A2 3.3.6 Jib cranes
The calculated deflection of jib cranes shall not exceed L/300 where L is the length of the
jib plus length of freestanding post.
Where the deflection is measured in situ by test methods, the permissible deflection may be
increased as follows:
(a) Where the jib crane is mounted on a rigid support, 50% to allow for such effects as
deformation of the anchoring bolts, baseplate, slew rings or other bearings and
fasteners.
(b) Where the jib crane is mounted on a flexible support, 100% to allow for such effects
as deformation of the anchoring bolts, baseplate, slew rings or other bearings and
fasteners, and deflection of the supporting structure.
5.1 MECHANISMS
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
A2 The mechanism which drives each motion shall comply with AS 1418.1.
1 See also Appendix D for illustrations of typical crane drive mechanisms.
2 Cranes are designed and built for a limited rated life, which may be extended or reduced
depending upon their usage. Devices are available to enable actual recording of rated life of
the crane to enable assessment of the remaining rated life. Guidance on this is given in
ISO 12482.1.
(e) Interlocks shall be provided to prevent operation of hoist motion unless all twistlocks
are fully open or fully closed.
(f) Where limit switches are positive in operation in one direction only, two such
switches shall be provided, each one utilized for operation in the positive direction
only.
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
S E C T ION 6 AC C E S S FR OM F IX E D
P LAT FOR M S
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(e) Brakes.
(f) Fluid couplings, clutches, gear-change mechanisms, and the like.
(g) V-belt and similar drives.
(h) Electrical equipment such as—
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(i) brushgear;
(ii) commutators and slip rings;
(iii) contactors;
(iv) control and switch panels;
(v) fuses and fuse boxes; and
(vi) limit switches, particularly hoisting.
Where the purchaser of a crane requires facilities for servicing additional items of
equipment such as lighting and other ancillaries, such facilities shall comply with the
relevant Part of AS 1418.
6.2.2.2 Manually operated cranes
Where a manually operated crane can be safely serviced from a portable ladder, permanent
means of access for servicing need not be provided. In such circumstances, provision shall
be made to ensure that the crane, or part of crane, against which the ladder is placed shall
not be capable of movement while it is being serviced. The height of the serviceable item
shall not exceed 6 m.
Temporary platforms to access high items shall require additional guarding.
6.2.3 Height for serviceable items
The maximum allowable height for any serviceable item above a service platform or
walkway shall be 1.9 m.
A1
6.3.2.4 Torsion box cranes The following clearances shall be applicable to torsion box
cranes as appropriate.
(a) Torsion box crane with walkway—clearances as per double girder crane (see
Clause 6.3.2.2).
(b) Torsion box crane without walkway—clearances as per single girder crane (see
Clause 6.3.2.1.
6.3.2.5 Multiple-crane installations
Where two or more cranes have adjacent out-of-service positions, access to each crane shall
be independent, i.e. no crane shall be used as a means of access to another.
Where two or more cranes are on a common runway, each crane should have an
out-of-service position so that all cranes can be serviced simultaneously.
6.3.2.6 Common fixed access to more than one crane
Where a fixed access platform provides access to more than one crane, each isolating
switch shall be arranged and marked to indicate, without possibility of misinterpretation,
the crane it isolates.
6.3.2.7 Access across an end carriage
Where an end carriage is used to provide a way of access to the other side of the crane, the
following conditions shall apply:
(a) An access isolator shall be provided in accordance with AS 1418.1.
(b) Standing, walking, and servicing surfaces (see AS 1418.1) shall be free of tripping
hazards, such as bolt heads and conduits.
(c) Adjacent standing or walking surfaces (see AS 1418.1) on the end carriage of more
than 300 mm difference in height shall be connected by steps.
(d) Standing and walking surfaces shall be not less than 300 mm clear width (in plan),
inside the handrail system; servicing surfaces shall be not less than 450 mm clear
width.
(e) A handrail shall be provided alongside any obstruction which has to be stepped over
(see Clause 6.3.3.3).
(f) The handrail system provided along the end carriage shall have a horizontal
clearance, outside the handrail from any fixed object, of not less than—
(i) where the handrail is of open type not less than 900 mm high .............. 225 mm;
(ii) where the handrail is panelled or meshed (50 mm × 50 mm) not less than
900 mm high................................................................................... 100 mm; or
(iii) where the handrail is panelled or meshed (50 mm × 50 mm), is not less than
1.5 m high, and is either extended not less than 300 mm past each end of the
end-carriage (i.e. the crane width) or returned at each end along the walkway
not less than 150 mm, and with a handrail not less than
900 mm high......................................................................................... 50 mm.
These positions are indicated in Figure C1.
(a) Above a rising ladder and above the access platform or walkway immediately
adjacent to the rising ladder for a distance of 600 mm from the edge of the platform
or walkway (see Figure C2)..............................................................................1.9 m.
(b) Above a walkway, platform, or other standing, walking, or servicing surface on the
crane or crab when the crane or crab is at the normal position for servicing
(see Figure C2) ................................................................................................1.8 m.
(c) Above a walkway, platform, or other standing, walking, or servicing surface on the
crane or crab when the crane or crab is at any other position than the normal position
for servicing—
(i) above the crab platform where the driver's cabin is mounted on the crab and
travels with the crab................................................................................1.8 m;
(ii) in the travel direction where access of personnel to the crane can be gained at
any travel position, or the crane may carry personnel, or where personnel are
required to remain on the crane while it is moving .............................. 1.8 m; or
(iii) in the travel direction (for the total length of travel), where access of personnel
can be gained only at the out-of-service position of the crane ...................1.4 m.
(d) Within the crane bridge ....................................................................................1.4 m.
6.3.3.2 Width of platforms and walkways
The width of platforms and walkways shall comply with the following:
(a) The width of a standing, walking, or servicing surface (see AS 1418.1) of a platform
or walkway shall be not less than—
(i) where the surface is level with the upper surface of the crane-bridge
member ............................................................................................... 900 mm
except that this may be reduced locally to not less than 600 mm past
unavoidable obstructions such as cabinets, mechanisms, or the like, provided
that the handrailing is continuous past the reduced-width section; or
(ii) where the surface is more than 450 mm below the upper surface of the
crane-bridge member (i.e. the platform or walkway is of the lowered or well
type) ................................................................................................. 600 mm.
(b) The horizontal distance between a moving crab or other part of a crane, and other
equipment or fixed parts of the crane on or above a platform, walkway, or servicing
surface on the crane bridge shall be not less than 450 mm (see Figure C3), except that
for end or return handrails (see AS 1418.1)—
(i) where the crab stops level with the end return handrail (in plan), the horizontal
clearance shall be not less than 150 mm; or
(ii) where the crab passes the end return handrail (in plan), the horizontal clearance
shall be not less than 300 mm.
Where (i) or (ii) apply and a handrail return would be less than 150 mm in length, it
may be omitted.
(c) The width between any two fixed items which could form a foot trap, on a standing or
walking surface (see AS 1418.1) of a platform or walkway shall be not less than
150 mm.
www.standards.com.au © Standards Australia
AS 1418.3—1997 16
(d) Access to crane platforms shall be provided by static platforms located at the top of a
ladder or stairway which shall have a clear horizontal distance of at least 600 mm
with no obstructions at the point of transfer, e.g. gates, chains, baulk bars
(see Figure C4).
6.3.3.3 Obstructions on a platform or walkway
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
S EC TION 7 AC C ES S FR OM M OB ILE
P LAT FOR M S
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
7.1 GENERAL
The mobile platform may be of a variable height or a fixed height, and shall comply with
AS 1418.10 or AS 1576, as appropriate.
NOTES:
3 It is recommended that fixed-service platforms should be installed.
4 For platforms complying with AS 1418.10, a scissors type mobile platform should be used in
preference to other types.
5 Mobile platforms are generally more suitable for servicing of single girder cranes or double
girder cranes with underslung crab than other types of cranes.
The vertical clearance above a handrail shall be not less than 450 mm with the crane in any
position (see also Clause 8.3).
The horizontal clearance between a moving crane, or part thereof, and an adjacent building
structure and any projections thereon shall be not less than the following as shown in
Figure C9:
(a) Where the crane is on an elevated runway and no walkway or platform is provided
adjacent to the runway ................................................................................... 50 mm.
(b) Where the crane is on an elevated runway and a platform or walkway is adjacent to
the runway................................................................................................... 450 mm.
(c) Where the crane runway is at ground level .................................................... 600 mm.
Where a projection extends from a moving crane over a platform or walkway alongside a
crane runway (travel or traverse), the projection, except where suitable precautions such as
flexible flaps or other type of guarding are provided to prevent injury to persons, shall not
extend below a line inclined upward from the centre of the rail-head surface at 30 degrees.
Refer to Figure C9.
S E C T ION 9 E LE C T R IC A L A C C E S S
IS O LA TOR S
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
9.1 GENERAL
Electrical isolation and protection shall be provided in accordance with AS 1418.1 and this
Section. In general, an access isolator shall be provided at the entry point to the crane, and
adjacent to the access point between parts of a crane, wherever one part of a crane can
move relative to another part.
(b) A warning, e.g. ‘THIS ISOLATOR DOES NOT ISOLATE THE CRANE FROM ITS
POWER SOURCE ’.
(a) where the driving mechanism and its control provide variable speed control or smooth
acceleration, the maximum travel speed shall be 72 m/min and the maximum traverse
speed shall be 30 m/min; or
(b) where the conditions in Item (a) do not apply, the maximum travel speed shall be
48 m/min and the maximum traverse speed shall be 24 m/min.
Where the travel speed is greater than 48 m/min, a pathway not less than 2 m wide shall be
provided in the travel direction for the crane operator.
(b) The mass of the lifting attachment expressed in the same unit as the rated capacity of
the lifting attachment (see Item (a)), e.g.
(i) TARE 100 kg;
(ii) TARE 1 t; or
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
11.3 MANUALS
11.3.1 General
The following manuals shall be provided.
(a) The crane operator’s manual.
(b) The maintenance manual.
(c) The logbook.
(d) The spare parts book.
NOTE: Attention is drawn to AS 1418.1, which specifies details of the electrical equipment and
control system that are to be provided.
11.3.2 Crane operator's manual
The crane operator’s manual shall be a formal publication, covered in a durable material
and of a size suitable for its use. It may be combined with another manual or be an
individual manual. It may be cross-referenced to other manuals of the crane. It shall present
the following information in plain English with explanations and definitions by words or
diagram where there is risk of misunderstanding:
(a) Ready identification of the make, model and serial number of the crane or where
appropriate, the range of serial numbers to which the information applies.
(b) All technical data of importance to the crane operator to ensure correct operation of
the crane.
(c) Description of and location of all safety devices, settings and adjustments.
(d) Instructions on the duties of the crane operator prior to operation, during operation
and after use.
(e) Instructions on restrictions in environmental conditions of wind and temperature.
(f) Description of safety precautions to be observed during maintenance and servicing of
the crane.
12.1 INSPECTION
Prior to its being commissioned, the crane shall be inspected in accordance with AS 1418.1.
12.2 COMMISSIONING
12.2.1 General
The following tests shall be carried out during the commissioning of cranes:
(a) Pre-operational inspection and testing.
(b) No-load operation and testing.
(c) Load testing.
The required performance of the crane should be agreed between the owner and supplier of
the crane. Normally, the required performance will be lifting, lowering, and moving the
maximum rated capacity at the rated speeds, smoothly with sufficient frequency to
represent the normal operation of the crane.
Safety procedures and precautions for each phase of inspection and testing should be agreed
between the owner and supplier of the crane prior to commissioning.
12.2.2 Pre-operational inspection and testing
Pre-operational inspection and testing (including alignment checking) shall be carried out to
ensure that all systems and items comply with the relevant drawings and specifications, and
shall include the following:
(a) Checking of runway tracks for level and alignment.
(b) Visual examination of all components, assemblies and drives and checking for
correctness of fitting including tolerances, clearances, alignments, and adjustments.
(c) Checking of greasing, oil levels, hydraulic systems, and pneumatic systems.
(d) Visual examination of welded and bolted connections of structures and torque check
all critical bolted connections.
(e) Checking of all safety guards and their fittings.
(f) Checking of details and correctness of electrical safety devices, circuits, earthing,
insulation cubicles, and cabling.
12.2.3 No-load operation and testing
Following satisfactory inspection and testing in accordance with Clause 12.2.2, no-load
operation and testing shall be carried out, and shall include the following:
(a) Cranes with pendant or cabin operating control These shall be as follows:
(i) The individual parts of the equipment shall be run under ‘manual’ control to
check the proper operation of alarms and warning devices, the tracking of the
crane, the operation of safety devices and the smooth acceleration and stopping
of the crane.
(ii) The crane shall be travelled and traversed over the full length of runways to
check physical clearance from fixed obstructions.
(iii) Pressure pipework shall be checked for leaks.
individual parts of the crane in accordance with Item (a) above, the crane shall be
tested in remote control mode in appropriate groups and then as a unit checking the
correct sequencing of the equipment for all functions and for smooth hoisting,
acceleration and retardation, until the reliability of the system at working
temperatures has been demonstrated.
12.2.4 Load testing
Following satisfactory no-load testing in accordance with Clause 12.2.3, load testing shall
be carried out, and shall include the following:
(a) The maximum rated capacity shall be applied to the main hoist at the point causing
maximum deflection. The maximum bridge deflection shall be checked and compared
with the calculated deflection under rated capacity (as supplied by the crane supplier).
The final deflection after removal of the load shall also be checked.
NOTE: The deflection of the crane support system under rated capacity should also be taken
into account.
(b) Each hoist in turn shall be used to lift its rated capacity, and shall be checked for
brake adjustment, hoisting speed and input current.
(c) With maximum rated capacity applied to the main hoist, the crane travel and traverse
shall be checked up to full speed to ensure that the load can be controlled
satisfactorily, and hoist brake application when lowering on power failure shall be
checked. The electrical system shall be checked for voltage drop and simultaneous
operation of main hoist and travel under full load and acceleration.
(d) Noise levels shall be checked, as required.
(e) At the time of commissioning only, each hoist shall be checked with 110% of its rated
capacity as in Item (b) above.
12.2.5 Reports
Accurate and complete reports of all testing shall be prepared. Such reports shall record all
the information checked during the test including clearances, temperatures, voltages,
currents, heat generation, noise levels, starting times, acceleration durations, stopping
times, settings and other control set points.
13.1 GENERAL
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
All guards shall be designed to prevent persons from reaching into the danger zone. This
requirement shall include preventing personnel from reaching over, under, around or
through any guard into the potentially dangerous area and shall be in accordance with
AS 4024.1 except where otherwise stated.
13.2 STRENGTH
The construction of a guard shall be robust and shall not collapse if personnel climb upon it.
The minimum mass to be supported by a guard shall be 75 kg.
13.3 MATERIAL
Where mesh or slatted guards are employed, the material used shall be sufficiently rigid to
prevent separation of the mesh or slats by finger pressure.
13.7 MARKING
All removable guards or inspection covers shall be clearly marked—
DANGER—ISOLATE POWER BEFORE REMOVING OR OPENING GUARD .
13.9 COLOUR
Travel motion wheel guards shall be painted in high visibility colours in accordance with
AS 1318.
APPENDIX A
INFORMATION TO BE SUPPLIED WITH ENQUIRY, ORDER, OR TENDER
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(Informative)
Sheet 1 of 2
Enquirer: Supplier:
1 Type of crane required
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
2 Clearance diagram (including height and span of crane track if existing, hook approaches and
hook path)
4 Site details:
(a) Foundation
6 Operating conditions:
locality;
hazardous conditions
Sheet 2 of 2
7 Application of cranes:
(a) Span
(ii) lowering
12 Special requirements of design and manufacture (e.g. painting, corrosion proofing, auxiliary
equipment required):
(a) Existing cranes
3 Crane performance:
(ii) lowering
5 Electrical details:
APPENDIX B
LIST OF TYPICAL HAZARDS
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(Informative)
This Appendix lists typical hazards of which a designer should be aware when designing a
bridge, gantry or portal crane. The list is for information only and is not exhaustive. There
are other potential hazards that are not listed. These hazards are applicable to the situations
described and could involve risks to persons if not reduced or eliminated. Typical hazards
are as follows:
(a) Mechanical hazards These can include the following:
(i) Crushing.
(ii) Shearing.
(iii) Cutting or severing.
(iv) Entanglement.
(v) Drawing-in or trapping.
(vi) Impact.
(vii) High pressure fluid ejection.
(viii) Ejection of parts.
(ix) Loss of stability.
(x) Slip, trip and fall.
(xi) Hazards to exposed persons due to uncontrolled movement.
(xii) Hazards due to rolling over.
(xiii) Inadequate means of access.
(xiv) Hazards due to towing, coupling connecting, transmission and the like.
(b) Electrical hazards One of the prime concerns is that of electrical contact.
(c) Hazards generated by neglecting ergonomic principles in machine design
(d) Hazard combinations
(e) Hazards caused by failure of energy supply, breaking down of machinery parts and
other functional disorders These can include the following:
(i) Failure of energy supply.
(ii) Failure or malfunction of control system.
(iii) Errors of fitting.
(iv) Overturn, unexpected loss of machine stability.
(f) Hazards caused by missing or incorrectly positioned safety-related
measures/means These include the following:
(i) Guards.
(ii) Safety-related (protection) devices.
(iii) Starting and stopping devices.
(iv) Safety signs and signals.
APPENDIX C
ACCESS AND CLEARANCE REQUIREMENTS FOR FIXED PLATFORMS
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(Normative)
Figures C1 to C9 illustrate access and clearance requirements for fixed platforms.
NOTE: Some of the details in these Figures have been simplified to enable relevant dimensions to
be shown clearly.
www.standards.com.au
41
© Standards Australia
AS 1418.3—1997
AS 1418.3—1997 42
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
A2 APPENDIX D
TYPICAL CRANE DRIVE DIAGRAMS
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
(Informative)
Typical denomination
for running gear
No. of wheel pairs
and drive systems
Crane drive (see Note) Remarks
diagrams
Synchronized
Total
FF FL or coupled
NW
NS
EFF EFL 2 —
EFF EFL 2 —
EFF EFL
Depends on — Additional details can be found in a
wheel load Demag publication by Dr Hanover on
distribution — ‘Crane Travel Behaviour’
EFF EFL
WFF 2 2
WFF 2 1
EFF EFL 4 —
L = loose-bearing support of the long-travel wheel, allowing side movement of crane structure
AS 1418.3—1997
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
REVISED TEXT
REVISED TEXT
SUMMARY: This Amendment applies to the Title, Clauses 1.4, 3.3.3(a), 3.3.6 and 5.1 and Appendix D
46
`NOTES
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
47
NOTES
AS 1418.3—1997
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
48
NOTES
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).
Standards Australia
Standards Australia is an independent company, limited by guarantee, which prepares and publishes
most of the voluntary technical and commercial standards used in Australia. These standards are
developed through an open process of consultation and consensus, in which all interested parties are
invited to participate. Through a Memorandum of Understanding with the Commonwealth government,
Standards Australia is recognized as Australia’s peak national standards body.
Australian Standards
Australian Standards are prepared by committees of experts from industry, governments, consumers
and other relevant sectors. The requirements or recommendations contained in published Standards are
a consensus of the views of representative interests and also take account of comments received from
other sources. They reflect the latest scientific and industry experience. Australian Standards are kept
under continuous review after publication and are updated regularly to take account of changing
technology.
International Involvement
Standards Australia is responsible for ensuring that the Australian viewpoint is considered in the
formulation of international Standards and that the latest international experience is incorporated in
national Standards. This role is vital in assisting local industry to compete in international markets.
Standards Australia represents Australia at both ISO (The International Organization
for Standardization) and the International Electrotechnical Commission (IEC).
Electronic Standards
All Australian Standards are available in electronic editions, either downloaded individually from our Web
site, or via on-line and CD ROM subscription services. For more information phone 1300 65 46 46 or
visit us at
www.standards.com.au
Licensed to MR GILBERTO DREAS on 16 November 2010. 1 user personal user licence only. Storage, distribution or use on network prohibited (10163511).