Professional Documents
Culture Documents
250 KL ELSR - 25 M Staging
250 KL ELSR - 25 M Staging
not authorised by us, nor be copied/made use of in full or part by such person or firm without our prior
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR
PROJECT :
DISTRICT -SONBHADRA
CODE REV.
DOC. No. G V P R U P 2 5 0 25 M 0 0 1
IS A
INDEX
1.0 Introduction
1.1 General
1.2 References
1.3 Design Philosophy
1.4 Material Specification
1.5 Permissible Stresses in materials
1.6 Analysis
9.0 Annexures
ANNEXURE -A :- Table 10 & 12 Of IS 3370 (PART-IV)-1967 for Moment and Hoop Coefficients
ANNEXURE -B :- Ductile Detailing Of Column as per IS 13920 : 2016
ANNEXURE -C :- Ductile Detailing Of Beam as per IS 13920 : 2016
ANNEXURE -D : Summary of weight of tank & Staging from Stadd
ANNEXURE -E : Summary of displacemnets from Stadd
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK -
Project : DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR Design Check Date
Title : PRADESH
PSD DHC 3/19/2021
1 INTRODUCTION:
1.1 General:
This document covers the design of Elevated service reservoir (Intze Type) with
Capacity = 250 Cum having a staging height = 25 m
The design of OHR includes the design of Roof Dome, Cylindrical wall, Conical Dome, Bottom dome,
Gallery Platform (Walkway Slab), Bottom and top Ring beam , Columns, Tie beams, Foundation
and Staircase.
The following Primary Loads are considered in the design of the tank portion
a) Dead Load
b) Live Load
c) Water Load inside the tank upto top of the cylindrical wall including free board.
d) Wind loads
e) Seismic loads
f) Combination of all the above loads.
1.2 References:
a) IS:456- 2000 - Plain & Reinforced Concrete - Code of Practice (Fourth revision)
b) IS:3370 - 2009 - Code of practice for Concrete Structures for the Storage of Liquids
Part I - General Requirements
Part II - Reinforced Concrete Structures
c) IS:1893 (Part: 2) - 2014 - Criteria for Earthquake resistant Design of Structures (Fifth revision)
d) IS:875 - Part: 1 to 3 - 1987 : Dead, Live and Wind Loads
e) IS:13920 - Ductile detailing of RCC Structures subjected to Seismic forces - Code of Practice
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR Design Check Date
Title : PRADESH
PSD DHC 3/19/2021
1.5 Permissible Stresses in materials ( as per IS 3370 (Part:2) - 2009)
Permissible Stresses in Concrete:
Relating to Resistance to Cracking
a) Direct Tension = 1.5 N/mm2 (From Table:1)
b) Bending Tension = 2.0 N/mm 2 (From Table:1)
Relating to Strength Calculation
a) Direct compression = 8 N/mm2 (From Table:2)
b) Bending compression = 10 N/mm2 (From Table:2)
1.6 Analysis :
Finite Element Analysis of ELSR is done by using STAAD Pro Software.
As Per IS 1893 Part 2 : 2014, P-∆ Analysis for staging is performed.
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK -
Project : DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR Design Check Date
Title : PRADESH
PSD DHC 3/19/2021
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
3.1.5 Loads
Wind Velocity = 47 m/s
Live Load on Roof = 1.5 kn/m2
Live Load on Walkway Slab = 3.0 kn/m2
Density of concrete = 25 kn/m³
Density of water = 10 kn/m³
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Load:
Average Thickness of Dome = 137.5 mm
Self weight = 0.1375*25 = 3.4375 kN/m²
Live load = 1.5 kN/m²
Finishes = 1.0 kN/m²
Total load W = 5.938 kN/m²
Say W = 6 kN/m²
Total vertical load on Dome = 2π*8.61*1.6*6 = 519.3 KN
Load per meter of periphery w = 519.34/π*10 = 16.53 kN/m
Sin θ = 5/8.61 = 0.581 `
Cos θ = 7.01/8.61 = 0.814
θ = 35.500 < 510 48”
Hence the entire dome is under compression.
Meridional Thrust T = WR / (1 + Cos θ) (Maximum at springings i.e.at θ =35.5)
6*8.61/(1+0.81) = 28.48 Kn/m
Max. Meridional stress
28475.84/(137.5*1000) = 0.21 N/mm²
Horizontal Thrust H = TCos θ
28.48*0.81 = 23.18 kN
Hoop stress = [wR / (1 + Cos θ)] x (-1 + Cos θ + Cos θ2)/(t x 100)
Hoop stress at springings i..e., θ =35.5
28475.84*(-1+0.814+0.663)/(137.5*1000) = 0.10 N/mm²
Provide 10 dia tor @ 150 mm c/c Radially and Circumferentially @ bottom (spacing measured at springings)
Bending Moment
Moment due to end restraint (at Springings) = WRt/4 √3 ( Refer Page no 552 of Timoshenko & Waimnesky)
6*8.61*0.15/(4*sqrt(3)) = 1.12 knm
Factored Bending moment = 1.68 knm
Effective thickness = 75 mm
Mu/bd^2 = 0.3
From SP16 table 4 Ast required = 0.07
Ast required = 53 mm2
Dia. Of bar ( f ) = 10 mm
Area of Bar = 79 mm2
Required Spacing = 1490 mm
Provided Spacing = 150 mm
Provided Area = 526.67 mm2
GVPR ENGINEERS LIMITED
Document No. Rev.
Project : CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK
-DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Increase the edge of the dome slab to 15 cm and reduce to12.5cm at 1mt from edge and provide extra rods 10mm dia
@150mm c/c on top face both Radially & Circumferentially in1 mtrs length to take care of edge moments
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Dia of Bar = 10 mm
Area of Bar = 78.54 mm2
Required Spacing = 220 mm
Provide Spacing = 180 mm
Provided Area of Steel = 440.00 mm2
Horizontal Steel :
Base to top
10 tor @180 c/c on each face
Vertical steel is provided for restraint and temperature effect .
Vertical Steel :
Bending moment :
Max Bending moment for side wall is considered to be fixed bottom and free top
Refer ( Appendix-1) Table-10 of IS:3370:Part-1V
Max B.M coefficient is @ 1 H for water face = -0.0212165
Max Bending Moment = (Coefficient) WH3 on water face
M =-0.0212165x10 x 3.25 ^3 = 7.28 knm
Max Bending moment Coefficient for Outer face = 0.0057
Max Bending Moment = (Coefficient) WH3 on other face
M =0.0056752x12 x 3.25 ^3 = 2.34 knm
Factored bending moment at water face = 10.92 kNm
Factored bending moment at outer face = 3.51 kNm
Effetive depth of wall required = √10.92x10^6/(0.133x30x1000)
52.31 mm
Provided Thickess = 200 mm Hence OK
Clear Cover on water face = 45 mm
Clear cover on other face = 45 mm
Effective thickness = 150 mm
Factored bending moment at water face = 10.92 kNm
Mu/bd^2 = 0.49
From SP16 table 4 Ast required = 0.115
Ast required = 173 mm2
Minimum Area of steel = 0.35x200 = 700 mm²
Water face :
Dia of Bar = 10 mm
Area of Bar = 78.54 mm2
Required Spacing = 220 mm
Provide Spacing = 180 mm
Provided Area of Steel = 436.33 mm²
Water face :
Provide 10 tor @180c/c Verticals Through
Factored bending moment at outer face = 3.51 kNm
Mu/bd^2 = 0.16
From SP16 table 4 Ast required = 0.04
Ast required = 56 mm2
Minimum Area of steel = 0.35x200 = 700 mm²
Outer face :
Dia of Bar = 10 mm
Area of Bar = 78.54 mm2
Required Spacing = 220 mm
Provide Spacing = 180 mm
Provided Area of Steel = 436.33 mm²
Outer face :
Provide 10tor @180c/c Verticals throughout
GVPR ENGINEERS LIMITED
Document No. Rev.
Project : CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK
-DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
W
2
fo
B
2
B
LOADS : 3
Load from top dome = 2*∏*R*h1*w = 519.3 Kn
Weight of Top Ring Beam = Π * (D1+b)*b*d*25
Π*10.3*0.3*0.3x25 = 72.81 Kn
Weight of Cylindrical Side Wall = Π * (D1+t)*h*t*25
Π*( 10+0.2)*2.825*0.2*25 = 452.62 Kn
Self weight of beam = Π * (D1+b) *b*h*2500
Π*(10+1100/1000)*1100*200/1000000*25 = 191.79 Kn
Live Load = 3.0 kn/m²
Load due to Railing = 1.0 kn/m²
Load due to Live load & Railing = 139.48 kn
Total Load W = 1376.0 kn
Vertical Load at ring beam level w = W / пD
Perimeter at Middle Ring Beam level = пD = 34.87 mt
Vertical Load at ring beam level w = 1376.04/34.87 = 39.46 kn/mt
Radial / Horizontal thrust H = w cotФ
tanФ = 1.25/1.475 = 0.847
Ф = 40°
cotФ = 1/ tanФ = 1.181
Radial / Horizontal thrust = 39.46*1.181 = 46.6 kn/mt
D = 10+1.1 = 11.1 mt
Hoop Tension = 46.6*11.1/2 = 258.63 Kn
Area of steel required = 1.5* Hooptension/0.50 *fy
= 1.5* Hooptension/0.50 *500
= 1551.78 mm2 on both faces
= 775.89 mm2 on each face
Ast = (0.35/100) x200 x 1000 = 700 mm²
Clear Cover on Water face = 45 mm
Clear Cover on outer face = 45 mm
Effective Depth = 197.00 mm
Dia of Bar = 16 mm
Area of Bar = 201.06 mm2
Required Spacing = 259.13 mm
Provided Spacing = 200 mm
Provided Area of Steel = 2010 mm2
No of bars required = 7.72 no
No of bars provided = 10 (5no on top & bottom)
Provide 16 tor @ 200 mm c/c Circumferentially at top & bottom
No of Bars = 7.00 no
Radial Steel
Min Area of Steel = 0.35 %
GVPR ENGINEERS LIMITED
Document No. Rev.
Project : CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK
-DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
h2
f0
LOADS :
a) Weight of structure upto Middle Ring Beam level = 1376.0 kn
b) Weight of water in portion of conical slab
Π*(7.5+2*1.25/3)*0.5*1.25*1.25*10 = 204.53 kn
c) Weight of water above frustrum of cone
Π*(10^2 -7.5^2)*2.95/4*10 = 1013.65 kn
d) Weight of conical slab
Π*(7.5+1.25)*1.77*200*25/1000 = 243.28 kn
Total Load W = 2837.5 kn
Load per metre length w = W/ΠD
Outer Diameter D = 7.5 mt
Load per metre length w =2837.5/ Π *7.5 = 120.43 kn/m
RADIAL REINFORCEMENT : sinØ
cosecØ = 0.646
= 1.548
Meridional stress at Ring Beam = w* cosecØ / 100 t = 9.32 kn/m2
0.00932 N/mm2
permissible direct compressive stress = 8.0 N/mm2
Minimum % of reinforcement for 200mm thk Wall = 0.35 %
Minimum area of reinforcement for 200mm thk Wall = 700 mm2 both faces
Dia of Bar = 10 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
HOOP REINFORCEMENT :
Max Hoop Tension = 281.08 kn
Area of steel required = 1.5* Hooptension/0.50 *fy
= 1.5* Hooptension/0.50 *500
= 1686.48 mm2 on both faces
= 843.24 mm2 on each face
Minimum area of reinforcement for 200mm thk Wall = 700 mm2 on both faces
Dia of Bar = 16 mm
Area of Bar = 201.06 mm2
Required Spacing = 240 mm
Provide Spacing = 180 mm
Provided Area of Steel = 2230 mm²
Provide Hoops of # 16 @ 180 mm c/c uniformly throughout on both faces ( 2230 sqmm)
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Provide 10 dia tor @180mm c/c radially and circumferentially @ Top and bottom (spacing measured at springings)
Bending Moment
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Dia of Bar = 10 mm
Area of Bar = 78.54 mm2
Required Spacing = 260 mm
Provide Spacing = 180 mm
Provided Area of Steel = 436.33 cm² on E/F
Provide thickness for dome slab to 200 mm at springings and provide 10mm dia @180mm c/c on top and bottom both
Radially & Circumferentially
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
Tanφ = 0.225
r1
0.225/3.525 = 0.064
φ = 3.65° 0.064 radians
α*Sinφ = 0.0334
α*Cosφ*cotα = 0.9051
α*Cosφ = 0.5225
α*Sinφ*cotα = 0.0578
Torsional Moment at Face of column
(229*3.525^2* (0.064-0.524+0.5225-0.0578)) = 13.94 knm
Distance of max torsion from face of the supports
2*Π*3.525*12.75/360-0.225 = 0.559 m < 0.644
Hence Safe
Equivalent Bending Moment at face of column M2 = T ( 1+D/b) / 1.7
D = 750 mm
b = 450 mm
M2 = (14*(1+0.75/0.45)/1.70) = 22 knm
Total Bending Moment at face of column M =M1+M2
M =174.89+21.87 = 196.76 knm
Factored Bending moment = 295.14 knm
Effective thickness = 644 mm
Mu/bd^2 = 1.58
From SP16 table 4 Ast required = 0.385
Ast required = 1116 mm2
GVPR ENGINEERS LIMITED
Document No. Rev.
Project : CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK
-DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
LONGITUDINAL REINFORCEMENT:
At Top :
Straight Bars Extra Bars
Dia of Bar = 16 mm 16 mm
Area of Bar = 201.06 mm2 201.06 mm2
Required no of Bars at top = 5.55 no's 1.55 no's
Provide no of Bars = 4 no's 4 no's
Provided Area of Steel = 804.24 mm2 804.24 mm2
Total Provided Area of Steel at top = 1608.48 mm2
At Bottom :
Straight Bars Extra Bars
Dia of Bar = 16 mm 12 mm
Area of Bar = 201.06 mm2 113.1 mm2
Required no of Bars at Bottom = 3.72 no's -0.50 no's
Provide no of Bars = 4 no's 4 no's
Provided Area of Steel = 804.24 mm2 452.4 mm2
Total Provided Area of Steel at Bottom = 1256.64 mm 2
At top:
Provide 4 - # 16 tor through + 4- # 16 extra at supports(1608.48sqmm >1116sqmm)
At Bottom:
Provide 4 - # 16 tor through + 4- # 12 extra over mid span(1256.64sqmm >748sqmm)
Shear force at 644 mm from face of column V'= Vo - w*(d+S2/2)
(666.5 mm from centre of column ) V
422-229*(666.5) = 223 kn
Equivalent shear at section of max torsion Ve = V' + 1.6 * T / b
(243+1.6*27/0.45) = 337.69 kn
Equivalent Shear Stress ζve = Ve/ (b*d)
506535/(450*644) = 1.75 N/mm2
Area of Steel at Support = 1608 mm2
pt = 0.55
ζc = 0.520 N/mm2
< 1.75
ζc < ζve
Shear Capacity of Section ﺡcbd = 150624.00 N
Net Shear = 337.69-150.624 = 187.07 Kn
TRANSVERSE REINFORCEMENT :
Dia of Stirrups = 8 mm
No of Legs = 4
Area of shear reinforcement as per Cl 41.4.3.of IS 456 -2000
Spacing should be lesser of the following :
A) Asv / Sv = (Tu / b1 * d1 * 0.87 fy) + (Vu / 2.5 * d1 * 0.87fy)
0.87fy = 435 N/mm2
Dia of main reinforcement = 16 mm
Dia of stirrups = 8 mm
Cover = 45 mm
b1 = 328.00 mm
GVPR ENGINEERS LIMITED
Document No. Rev.
Project : CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK
-DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
d1 = 628.00 mm
Asv = 201.06 mm2
The spacing of hoops over a length of 2d at either ends of a beam shall not exceed
(a) d/4 = 176.05 mm
(b) 8 times the diameter of the smallest longitudinal bar = 128 mm
(c) 100 mm = 100 mm
The spacing of hoops over a length of 2d at either end of a beam shall be provided is
Min ( = 100 mm
Provide Spacing at Supports = 100 mm
Elsewhere, the beam shall have vertical hoops at a spacing not exceeding d/2.
d/2 = 352.1 mm
Elsewhere, the beam shall have vertical hoops at a spacing of = 200 mm
Stirrups :
Hence Provide 4L - Y8 stirrups Spacing @ 100 mm c/c throughout
GVPR ENGINEERS LIMITED
Document No.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project : BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check
Title : UTTAR PRADESH PSD DHC
Crack width calculation for Top dome :
Check for Crack Width for Bending Moment
As Per IS 3370-2009 (Part II) Annex-B
1) Sectional Properties:
Width, b = 1000 mm fc/Ec
Depth, d = 150 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 10 mm d D
Spacing, S = 150 mm
d-x fs/Es
Effective Depth, d = 100 mm
Area of Steel, Ast = 523.33
Total Cover, ec = 50 mm b ε1
Section Strain Diagram
Grade Of Concrete, fck = M 30
Grade Of Steel, fy = Fe 500
⇒ x = 0.24089 x 100
= 24.089 mm
⇒ fc = 2 Ms/(x*b*z)
= ### N/mm²
< 0.45 fck (13.5) N/mm² Hence Safe
⇒ fs = Ms/(As*z)
= 23.27 N/mm²
< 0.8 fy (400) N/mm² Hence Safe
< 130 N/mm²
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
4) Nominal Strain ε1 :
From Strain Diagram,
ε1 = fs × D − x
Es d − x
= 0.000193
ε2 = bt ሺD − xሻ(a′ − x)
3 Es As (d − x)
= 0.0006651 > ε1
3 acr εm
w =
2 (acr − Cmin )
1+ D−x
= -0.077 mm
< 0.2 mm
Date
3/19/2021
D-x
ain Diagram
tensile stress in steel
ec =
cmin+ dia/2
50 mm
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project : BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
1) Sectional Properties:
Width, b = 1000 mm
Depth, d = 125 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 10 mm
Spacing, S = 150 mm
Effective Depth, d = 75 mm
Area of Steel, As = 523 mm²
Area of Concrete, Ac = 125000 mm²
Total Cover, ec = 50 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must
be less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 1.315 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000007
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0007967 > ε1
w = 3 acr εm
= -0.202 mm
< 0.2 mm
Hence the design crack width is with in the allowable limit.
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project : BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
1) Sectional Properties:
Width, b = 300 mm
Depth, d = 300 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 12 mm
Spacing, S = 186 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must
be less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 9.182 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000046
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0004425 > ε1
w = 3 acr εm
= -0.119 mm
< 0.2 mm
Hence the design crack width is with in the allowable limit.
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF Document No. Rev.
Project : VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -
SONBHADRA GVPR-250KL-25M-001 A
1) Sectional Properties:
Width, b = 1000 mm fc/Ec
Depth, d = 200 mm
Clear Cover, Cmin = 45 mm x
Dia of bar, dc = 10 mm d D
Spacing, S = 180 mm
d-x fs/Es D-x
Effective Depth, d = 150 mm
Area of Steel, Ast = 436.1
Total Cover, ec = 50 mm b ε1
Section Strain Diagram
Grade Of Concrete, fck = M 30
Grade Of Steel, fy = Fe 500
⇒ x = 0.18594 x 150
= 27.891 mm
⇒ fc = 2 Ms/(x*b*z)
= ### N/mm²
< 0.45 fck (13.5) N/mm² Hence Safe
⇒ fs = Ms/(As*z)
= 118.64 N/mm²
< 0.8 fy (400) N/mm² Hence Safe
< 130 N/mm²
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
4) Nominal Strain ε1 :
From Strain Diagram,
ε1 = fs × D − x
Es d − x
= 0.000836
ε2 = bt ሺD − xሻ(a′ − x)
3 Es As (d − x)
= 0.0009271 > ε1
3 acr εm
w =
2 (acr − Cmin )
1+ D−x
= -0.017 mm
< 0.2 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM Designed Checked Date Rev.
Title : GHATI (Zone-C) UTTAR PRADESH PSD DHC 3/19/2021 A
Crack width calculation for Cylindrical wall :
Check for Crack Width for Direct Tension
As Per IS 3370-2009 (Part II) Annex-B
1) Sectional Properties:
Width, b = 1000 mm
Depth, d = 200 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 10 mm
Spacing, S = 180 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must be less than the
limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 3.64 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000018
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
3) Strain Hardening due to Stiffening effect, ε2 :
As per Annexure B of IS 3370:2009 (Part II)
ε2 =
= 0.0015291 > ε1
w = 3 acr εm
= -0.444 mm
< 0.2 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check
Title : UTTAR PRADESH
PSD DHC
1) Sectional Properties:
Width, b = 1100 mm
Depth, d = 200 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 16 mm
Spacing, S = 200 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must be
less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 8.049 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000040
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0003648 > ε1
w = 3 acr εm
= -0.102 mm
< 0.2 mm
Date
3/19/2021
cmin+ dia/2
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project : BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
1) Sectional Properties:
Width, b = 1000 mm
Depth, d = 200 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 16 mm
Spacing, S = 180 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must be
less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 9.862 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000049
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0005974 > ε1
w = 3 acr εm
= -0.159 mm
< 0.2 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Design Check
Title : (Zone-C) UTTAR PRADESH PSD DHC
Crack width calculation for Bottom dome :
Check for Crack Width for Bending Moment
As Per IS 3370-2009 (Part II) Annex-B
1) Sectional Properties:
Width, b = 1000 mm fc/Ec
Depth, d = 200 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 10 mm d D
Spacing, S = 180 mm
d-x fs/Es
Effective Depth, d = 150 mm
Area of Steel, Ast = 436.11
Total Cover, ec = 50 mm b ε1
Section Strain Diagram
Grade Of Concrete, fck = M 30
Grade Of Steel, fy = Fe 500
⇒ x = 0.18594 x 150
= 27.891 mm
⇒ fc = 2 Ms/(x*b*z)
= ### N/mm²
< 0.45 fck (13.5) N/mm² Hence Safe
⇒ fs = Ms/(As*z)
= 18.253 N/mm²
< 0.8 fy (400) N/mm² Hence Safe
< 130 N/mm²
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
4) Nominal Strain ε1 :
From Strain Diagram,
ε1 = fs × D − x
Es d − x
= 0.000129
ε2 = bt ሺD − xሻ(a′ − x)
3 Es As (d − x)
= 0.0009271 > ε1
3 acr εm
w =
2 (acr − Cmin )
1+ D−x
= -0.151 mm
< 0.2 mm
Date
3/19/2021
D-x
in Diagram
nd the tensile stress in
:
th is not Required
ec =
cmin+ dia/2
50 mm
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project : BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
1) Sectional Properties:
Width, b = 1000 mm
Depth, d = 175 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 10 mm
Spacing, S = 180 mm
For the crack width formula to be valid, the tensile stress in steel under service conditions must
be less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 4.325 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000022
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0013376 > ε1
w = 3 acr εm
= -0.387 mm
< 0.2 mm
Hence the design crack width is with in the allowable limit.
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
Project : VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Design Check Date
Title : (Zone-C) UTTAR PRADESH PSD DHC 3/19/2021
Check for Crack Width for Bottom Ring beam
Check for Crack Width for Bending Moment
As Per IS 3370-2009 (Part II)
1) Sectional Properties:
Width, b = 450 mm fc/Ec
Depth, d = 750 mm
Clear Cover, Cmin = 45 mm x
Dia of bar, dc = 16 mm d D
Spacing, S = ###
d-x fs/Es D-x
Effective Depth, d = 697 mm
Area of Steel, Ast = 1206 mm²
Total Cover, ec = 53 mm b ε1
Section Strain Diagram
Grade Of Concrete, fck = M 30
Grade Of Steel, fy = Fe 500
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Design Check Date
Title : (Zone-C) UTTAR PRADESH PSD DHC 3/19/2021
⇒ x = 0.21057 x 697
= 146.767 mm
⇒ fc = 2 Ms/(x*b*z)
= ### N/mm²
< 0.45 fck (13.5) N/mm² Hence Safe
⇒ fs = Ms/(As*z)
= 251.746 N/mm²
< 0.8 fy (400) N/mm² Hence Safe
> 130 N/mm²
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is Required
4) Nominal Strain ε1 :
From Strain Diagram,
fs D−x
ε1 = ×
Es d − x
= 0.001380
GVPR ENGINEERS LIMITED
Document No. Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
Project : VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Design Check Date
Title : (Zone-C) UTTAR PRADESH PSD DHC 3/19/2021
bt ሺD − xሻ(a′ − x)
ε2 =
3 Es As (d − x)
= 0.0004113 < ε1
3 acr εm
w =
2 (acr − Cmin )
1+
D−x
= 0.189 mm
< 0.2 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Design Check Date
Title : UTTAR PRADESH
PSD DHC 3/19/2021
1) Sectional Properties:
Width, b = 450 mm
Depth, d = 750 mm
Clear Cover, Cmin = 45 mm
Dia of bar, dc = 16 mm
Spacing, S = ###
For the crack width formula to be valid, the tensile stress in steel under service conditions must
be less than the limiting values as follows:
Strain in Reinforcement, ε1 ≤ 0.8 fy/Es
fs =
= 2.906 N/mm²
Strain in Reinforcement,
ε1 = fs/Es
= 0.000015
< 0.8 fy/Es (0.002) Hence Safe
Hence as per Clause No. 4.4.3.1 of IS 3370:2009 (Part II), Check for Crack width is not Required
ε2 =
= 0.0009328 > ε1
w = 3 acr εm
= -0.188 mm
< 0.2 mm
Hence the design crack width is with in the allowable limit.
GVPR ENGINEERS LIMITED
Document No Rev
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
Project VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -
SONBHADRA GVPR-250KL-25M-001 A
4.2 Live loads (As per IS: 875 - Part: 2 - Live Loads)
Live load on Top dome = 1.5 kN/Sqm
Live load on Staircase = 3 kN/Sqm
Live load on walkway = 3 kN/Sqm
Legend:
DL : Dead Load/Dead+Water Loads
LL : Live Load
EQ+X : Seismic Load in X+ Direction WLX+ : Wind Load in X+ Direction
EQ-X : Seismic Load in X- Direction WLX- : Wind Load in X- Direction
EQ+Z : Seismic Load in Z+ Direction WLZ+ : Wind Load in Z+ Direction
GVPR ENGINEERS LIMITED
Document No Rev
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
Project VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -
SONBHADRA GVPR-250KL-25M-001 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date 19-Mar-21
TITLE
(Zone-C) UTTAR PRADESH Rev A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date 19-Mar-21
TITLE
(Zone-C) UTTAR PRADESH Rev A
Projected area of the Tank upto top of bottom slab
Shape factor for circular Structure= 0.70
GVPR ENGINEERS LIMITED
Document no
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
PROJECT VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -
SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date 19-Mar-21
TITLE
(Zone-C) UTTAR PRADESH Rev A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date 19-Mar-21
TITLE
(Zone-C) UTTAR PRADESH Rev A
From table Force Coefficient for flat-sided Members, Cf = 1.700
-28 of IS
875
GVPR ENGINEERS LIMITED
Document no
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF
PROJECT VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -
SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date 19-Mar-21
TITLE
From table (Zone-C) UTTAR PRADESH Rev A
-28 of IS
875 Force Coefficient for Circular-Sections, Cf = 0.800
Force on Ring Beam (0m - 10m) 0.75 x 0.8 x 1.153 = 1.470 kN/m
Force on Ring Beam (10m - 15m) 0.75 x 0.8 x 1.271 = 1.621 kN/m
Force on Ring Beam (15m - 20m) 0.75 x 0.8 x 1.32 = 1.683 kN/m
Force on Ring Beam (20m - 30m) 0.75 x 0.8 x 1.447 = 1.845 kN/m
GVPR ENGINEERS LIMITED
Document No Rev.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO
PROJECT GROUP OF VILAGES BLOCK -DUDDHI, BABHANI AND
MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
For staging portion two third weight of staging weight is applied at Beam column joints.
Total seismic weight by the no of nodes for Full Tank Condition is = 78.30 kN
By assign Pinned joints in staad and taken the forces at joints from staad.
Total seismic weight by the no of nodes for Tank empty Condition is = 35.28 kN
By assign Pinned joints in staad and taken the forces at joints from staad.
Total seismic weight by the no of nodes will get the joint weight at one node i.e 19.03 kN
By assign Pinned joints in staad and taken the forces at joints from staad.
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF Document no
VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA
PROJECT:
GVPR-250KL-25M-001
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
hi = height of impulsive mass above bottom of tank wa ll ( without Considering base pressure) = 1.234
hi* / h (Fig 2 (b) IS 1893(PART-2):2014) = 1.30
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF Document no
VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA
PROJECT:
GVPR-250KL-25M-001
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
hc= height of convective mass above bottom of tank wall( without Considering base pressure) = 1.810
hc*/h (Fig 2 (b) IS 1893(PART-2):2014) = 1.10
hc* =height of convective mass above bottom of tank wall( Considering base
pressure) = 3.619
3) Time Period :
i) Time Period of Impulsive Mode :
Ti = 2*Π √(mi+ms) /(Ks) (clause 4.3.1.3 of IS 1893(PART-2):2014))
mi = impulsive mass of liquid = 903.46
(Weight of empty container+ 1/3 weight of staing ) ms = 2116.67
Deflection from stadd when 10 kn force obtained at CG = 0.0026
Lateral stiffness of staging = 10/0.002552
= 3919
Time Period = 1.74
Tc = 3.5√10/9.81 = 3.534
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
For 0.67 < T > 4.0, Sa /g for Medium Soil = 1.36/T = 0.38
Multiplication factor for 0.5 % Damping = 1.75
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF Document no
VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA
PROJECT:
GVPR-250KL-25M-001
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
DESIGNED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM
TITLE :
GHATI (Zone-C) UTTAR PRADESH PSD
GVPR-250KL-25M-001
CHECKED
DHC
cum
mt
mt
mt
mt
mt
mt
m
m
m
m
m³
m³
KN
Kg
kn
kn
kn
of Spring mass model, an equivalent circular container of same volume and
nk at top level of liquid will be considered.
mt
kg
kn
kg
kg
mt
GVPR ENGINEERS LIMITED
Document no
GVPR-250KL-25M-001
CHECKED
DHC
mt
GVPR ENGINEERS LIMITED
Document no
GVPR-250KL-25M-001
CHECKED
DHC
mt
mt
kn
kn
m
kn/m
Sec
Sec
GVPR ENGINEERS LIMITED
Document no
GVPR-250KL-25M-001
CHECKED
DHC
N/m²
Kg/m²
m
m
N/m²
Kg/m²
N/m²
Kg/m²
m
m
N/m2
Kg/m²
0.075x0.2x 25000
N/m2
GVPR ENGINEERS LIMITED
Document no
GVPR-250KL-25M-001
CHECKED
DHC
N/m2
N/m2
kN/m2
kN/m2
2.962/32.9x 100
%
of hydrostatic pressure
dynamic pressure in this case does not affect container design.
GVPR ENGINEERS LIMITED
Document
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO
PROJECT: GROUP OF VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR
GVPR-250KL-25M-001
DISTRICT -SONBHADRA
C O L U M N N O. 2011 D E S I G N R E S U L T S
CHECKED
DHC
GVPR ENGINEERS LIMITED
Document Rev
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO
PROJECT: GROUP OF VILAGES BLOCK -DUDDHI, BABHANI AND MYORPUR
DISTRICT -SONBHADRA GVPR-250KL-25M-001 A
BB EE AA M
M NN O.
O. 2007
562 D
D EE SS II G
GNN RR EE SS U
U LL TT SS
m
m
m
m
sqm
cum
kN/sqm
kN/sqm
kN/sqm
m
kN/sqm
kN/sqm
pmin check
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
GVPR ENGINEERS LIMITED
Revision
Safe
Safe
GVPR ENGINEERS LIMITED
Document No.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project
BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
7.1) Design of Annular Raft :
Grade of concrete ( fck ) = M 30
Grade of steel ( fy ) = Fe 500
Total Load coming from columns = 6765.82 Kn
Maximum Bending moment due to wind = 396.50 knm
Add 10 % for Weight of Footing = 676.58 Kn
Total Weight = 7442.40 Kn
Say = 7500.00 Kn
Net Safe Bearing Capacity of Soil = 120.00 kn/m2
Soil bearing capacity in wind load case = 150.00 kn/m2
Area of Footing required (A) = 62.50 m2
Area of footing on either sides of ring beam is equal
Centre to centre diameter of staging = 7.05 mt
Radius of inner edge of Footing Ri
Π*( R2 - Ri2 ) = A / 2
Ri = (SQRT((3.525^2-(62.5/2*Π)) = 1.574 mt
Say Ri = 1.2 mt
Radius of outer edge of Footing Ro
Π*( Ro2 - R2 ) = A / 2
Ro = (SQRT((3.525^2+(62.5/(2*Π)) = 4.73 mt
Say Ro = 5 mt
(2/3)*( Ro3 - Ri3 )/( Ro2 - Ri2 ) = R
(2/3)*( 5^3 - 1.2^3 )/( 5^2 - 1.2^2 ) = 3.49 mt
= 3.53 mt
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Tanφ = 0.225
r1
= 0.064 radians
φ = 3.65 °
α*Sinφ = 0.0334
α*Cosφ*cotα = 0.9051
Moment at Face of column M1
(363*3.525^2* (-1+0.0334+0.9051)) = -277.600
Torsional Moment at Face of column = w*r12*(φ-α+α cos φ -α sin φ * cotα )
α*Cosφ = 0.5225
α*Sinφ*cotα = 0.0578
Torsional Moment at Face of column
(363*3.525^2* (0.064-0.524+0.5225-0.0578)) = 22.52 knm
Distance of max torsion from face of the supports
2*PI()*3.525*12.75/360-0.225 = 0.559 m
< 0.780
Equivalent Bending Moment at face of column M 2 = T ( 1+D/b) / 1.7
D = 900 mm
b = 450 mm
M2 = (23*(1+0.9/0.45)/1.70) = 40 knm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Area of Reinforcement for span moment
Mu/bd2 = 1.38
Percentage of steel required as per SP-16 = 0.33
Ast required = 1172 mm2
LONGITUDINAL REINFORCEMENT:
At Bottom :
Straight Bars
Dia of Bar = 20 mm
Area of Bar = 314.16 mm2
Required no of Bars at top = 4.76 no's
Provide no of Bars = 6 no's
Provided Area of Steel = 1884.96 mm2
Provided Area of Steel at bottom = 1884.96 mm2
Total Provided Area of Steel at bottom = 1884.96 mm2
At Top :
Straight Bars
Dia of Bar = 20 mm
Area of Bar = 314.16 mm2
Required no of Bars at Bottom = 3.73 no's
Provide no of Bars = 6 no's
Provided Area of Steel = 1884.96 mm2
Total Provided Area of Steel at top = 1884.96 mm2
At Bottom:
Provide 3 - # 20 tor through + 3- # 20 extra at supports(1884.96sqmm >1495sqmm)
At Top:
Provide 3 - # 20 tor through + 3- # 20 extra at supports(1884.96sqmm >1172sqmm)
GVPR ENGINEERS LIMITED
Document No.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project
BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Shear force at 78cm from face of column V '= Vo - w * ( d + S2/2)
(100.5cm from centre of column ) V
(670-95*(1.005) = 574 kn
Equivalent shear at section of max torsion Ve = V' + 1.6 * T / b
(385+1.6*42/0.45) = 536.02 kn
Equivalent Shear Stress ζve = 1.5 x Ve/ (b*d)
536020 x 1.5 /(450*780) = 2.29 N/mm2
Area of Steel at Support = 1884.96 mm2
pt = 0.54
From table 19 of IS 456, permissible shear stress of concrete ζc = 0.510 N/mm2
Shear Capacity of Section ﺡcbd=0.51*450*780 = 179010 N
Net Shear =536020-179010 = 357010 N
TRANSVERSE REINFORCEMENT :
Dia of Stirrups = 10 mm
No of Legs = 4
Area of shear reinforcement as per Clause 41.4.3. of IS 456 - 2000
Spacing should be lesser of the following :
A) Asv / Sv = (T / b1 * d1 * σsv) + (V / 2.5 * d1 * σsv)
σsv = 0.87 fy = 435 N/mm2
Dia of main reinforcement = 20
Dia of stirrups = 10
Cover = 75.00
b1=(450-10*2-75*2-20)/10 = 260.00 mm
d1=(900-10*2-75*2-20)/10 = 710.00 mm
Asv = 314.16 sqmm
Asv / Sv = 42*1.5
*10^6/(260*710*435)+(384973.3x1.5/(2.5*710*435)) = 1.54
Asv / Sv = 1.54
Sv=314.16/1.54 = 203.81 mm
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Dia of Stirrups = 10 mm
No of Legs = 4
Asv = 314.16 mm2
Minimum Shear Reinforcement = Asv / bSv >= (0.4/0.87fy )
Sv < = = 759.22 mm
0.75 d = 532.5 mm
= 300 mm
Provided Spacing is Lesser of above two cases = 200 mm
Stirrups :
Provide support to 800 # 10 - 4L stirrups @ 150 mm c/c
Provide 800 to center # 10 - 4L stirrups @ 200 mm c/c
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Net Upward pressure = 95.46 kn/m2
Length of projection of footing inner side Li=3.525-1.2-0.225 = 2.1 mt
Length of projection of footing outer side Lo=5-3.525-0.225 = 1.25 mt
GVPR ENGINEERS LIMITED
Document No.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project
BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
= 0.00069 m2 in 1 mt
Dia of Bar = 12 mm
Area of Bar = 113.1 mm2
Spacing required = 0.16 m
Spacing Provided = 163.91
= 125 mm
Area of Steel Provided 1610 mm2
Provide 12 tor Rings @125 mm c/c ( spacing measured at outer face of Ring Beam )
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Depth of footing at distance = d/2 = (824.2)/2 mm
900-(900-250)*412.1/2100 = 772.45 mm
Effective depth 'd' = 689.45 mm
GVPR ENGINEERS LIMITED
Document No.
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES
Project
BLOCK -DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA GVPR-250KL-25M-001
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) Date
Title
UTTAR PRADESH 19-Mar-21
Shear Stress ζve = 1.5 x Ve/ (b*d) = 0.35 N/mm2
< ζc
ζc = 0.16√fck = 0.88 N/mm2
Hence, Safe
250KL-25M-001
Rev
A
cument No.
250KL-25M-001
Rev
A
rad
rad
rad
cument No.
250KL-25M-001
Rev
A
de of a section
the beam shall
ut
cument No.
250KL-25M-001
Rev
A
m^2 in width of
2.1mt
m2 in 1 mt
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 11 DL+LL 2.496 1147.281 0.068 -0.202 -0.011 -3.534
1727 11 DL+LL 2.436 1137.926 -0.92 -0.875 -0.085 -3.346
1728 11 DL+LL 0.893 1113.704 0.166 0.439 0.106 -2.157
1729 11 DL+LL 2.59 1120.895 0.134 -0.127 0.001 -2.637
1730 11 DL+LL 0.673 1107.116 0.267 -0.451 -0.083 -1.854
1731 11 DL+LL 1.861 1138.899 0.284 -0.154 0.094 -2.819
11 DL+LL 10.949 6765.821 -0.001 -1.37 0.022 -16.347
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 12 DL+ EQ+X + 0.3EQ+Z 2.293 1044.509 0.015 0.007 0 -3.721
1727 12 DL+ EQ+X + 0.3EQ+Z 2.578 1027.198 -0.406 -0.313 -0.002 -3.925
1728 12 DL+ EQ+X + 0.3EQ+Z 1.541 999.375 -1.21 -0.972 0.015 -3.092
1729 12 DL+ EQ+X + 0.3EQ+Z 0.492 984.926 -0.002 -0.034 0.001 -2.182
1730 12 DL+ EQ+X + 0.3EQ+Z 1.529 997.822 1.21 0.916 -0.002 -3.073
1731 12 DL+ EQ+X + 0.3EQ+Z 2.517 1028.905 0.393 0.293 0.014 -3.872
12 DL+ EQ+X + 0.3EQ+Z 10.95 6082.735 -1.2143E-17 -0.103 0.026 -19.865
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 13 DL+ EQ-X + 0.3EQ-Z 2.293 1044.509 0.015 0.007 0 -3.721
1727 13 DL+ EQ-X + 0.3EQ-Z 2.578 1027.198 -0.406 -0.313 -0.002 -3.925
1728 13 DL+ EQ-X + 0.3EQ-Z 1.541 999.375 -1.21 -0.972 0.015 -3.092
1729 13 DL+ EQ-X + 0.3EQ-Z 0.492 984.926 -0.002 -0.034 0.001 -2.182
1730 13 DL+ EQ-X + 0.3EQ-Z 1.529 997.822 1.21 0.916 -0.002 -3.073
1731 13 DL+ EQ-X + 0.3EQ-Z 2.517 1028.905 0.393 0.293 0.014 -3.872
13 DL+ EQ-X + 0.3EQ-Z 10.95 6082.735 -1.2143E-17 -0.103 0.026 -19.865
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 14 DL+ EQ+Z + 0.3EQ+X 2.293 1044.509 0.015 0.007 0 -3.721
1727 14 DL+ EQ+Z + 0.3EQ+X 2.578 1027.198 -0.406 -0.313 -0.002 -3.925
1728 14 DL+ EQ+Z + 0.3EQ+X 1.541 999.375 -1.21 -0.972 0.015 -3.092
1729 14 DL+ EQ+Z + 0.3EQ+X 0.492 984.926 -0.002 -0.034 0.001 -2.182
1730 14 DL+ EQ+Z + 0.3EQ+X 1.529 997.822 1.21 0.916 -0.002 -3.073
1731 14 DL+ EQ+Z + 0.3EQ+X 2.517 1028.905 0.393 0.293 0.014 -3.872
14 DL+ EQ+Z + 0.3EQ+X 10.95 6082.735 -1.2143E-17 -0.103 0.026 -19.865
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 15 DL+ EQ-Z + 0.3EQ-X 2.293 1044.509 0.015 0.007 0 -3.721
1727 15 DL+ EQ-Z + 0.3EQ-X 2.578 1027.198 -0.406 -0.313 -0.002 -3.925
1728 15 DL+ EQ-Z + 0.3EQ-X 1.541 999.375 -1.21 -0.972 0.015 -3.092
1729 15 DL+ EQ-Z + 0.3EQ-X 0.492 984.926 -0.002 -0.034 0.001 -2.182
1730 15 DL+ EQ-Z + 0.3EQ-X 1.529 997.822 1.21 0.916 -0.002 -3.073
1731 15 DL+ EQ-Z + 0.3EQ-X 2.517 1028.905 0.393 0.293 0.014 -3.872
15 DL+ EQ-Z + 0.3EQ-X 10.95 6082.735 -1.2143E-17 -0.103 0.026 -19.865
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 16 DL+WLX+ -21.42 668.646 0.064 -0.003 -0.014 47.008
1727 16 DL+WLX+ -32.454 840.277 -8.968 -8.097 0.605 54.594
1728 16 DL+WLX+ -32.705 1181.669 5.48 3.837 -0.475 54.95
1729 16 DL+WLX+ -19.954 1350.533 -0.03 -0.051 -0.015 43.721
1730 16 DL+WLX+ -32.976 1180.953 -5.367 -3.789 0.453 55.187
1731 16 DL+WLX+ -32.353 841.469 8.821 7.863 -0.63 54.539
16 DL+WLX+ -171.862 6063.547 1.9429E-16 -0.24 -0.076 309.999
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 17 DL+WLX- 22.534 1409.69 -0.032 0.02 0.013 -49.469
1727 17 DL+WLX- 37.184 1209.847 6.269 4.506 0.487 -62.27
1728 17 DL+WLX- 36.204 812.83 -9.786 -8.746 -0.595 -61.299
1729 17 DL+WLX- 24.419 608.654 0.027 -0.016 0.016 -53.071
1730 17 DL+WLX- 36.458 810.445 9.674 8.587 0.644 -61.503
1731 17 DL+WLX- 36.961 1212.079 -6.152 -4.313 -0.445 -62.111
17 DL+WLX- 193.76 6063.545 -1.0755E-16 0.038 0.12 -349.723
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 18 DL+WLZ+ 4.193 1044.294 -46.79 -74.222 0.067 -6.677
1727 18 DL+WLZ+ -6.305 1383.514 -30.847 -60.615 -0.509 3.324
1728 18 DL+WLZ+ 10.201 1356.814 -31.642 -61.338 0.505 -10.037
1729 18 DL+WLZ+ -1.203 984.327 -47.001 -74.371 -0.1 0.609
1730 18 DL+WLZ+ -7.438 631.864 -31.874 -62.776 -0.6 4.195
1731 18 DL+WLZ+ 11.5 662.734 -32.6 -63.371 0.587 -11.11
18 DL+WLZ+ 10.948 6063.547 -220.754 -396.693 -0.05 -19.696
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 19 DL+WLZ- 3.72 1042.971 46.817 74.233 -0.069 -6.218
1727 19 DL+WLZ- 11.731 662.162 32.661 63.299 -0.571 -11.382
1728 19 DL+WLZ- -7.384 633.203 31.843 62.704 0.606 4.057
1729 19 DL+WLZ- -1.15 983.811 47.006 74.314 0.101 0.486
1730 19 DL+WLZ- 10.234 1355.058 31.67 61.305 -0.488 -10.141
1731 19 DL+WLZ- -6.202 1386.341 30.756 60.645 0.522 3.161
19 DL+WLZ- 10.949 6063.546 220.753 396.5 0.101 -20.037
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 20 DL+LL+ EQ+X + 0.3EQ+Z 2.496 1147.281 0.068 -0.202 -0.011 -3.534
1727 20 DL+LL+ EQ+X + 0.3EQ+Z 2.436 1137.926 -0.92 -0.875 -0.085 -3.346
1728 20 DL+LL+ EQ+X + 0.3EQ+Z 0.893 1113.704 0.166 0.439 0.106 -2.157
1729 20 DL+LL+ EQ+X + 0.3EQ+Z 2.59 1120.895 0.134 -0.127 0.001 -2.637
1730 20 DL+LL+ EQ+X + 0.3EQ+Z 0.673 1107.116 0.267 -0.451 -0.083 -1.854
1731 20 DL+LL+ EQ+X + 0.3EQ+Z 1.861 1138.899 0.284 -0.154 0.094 -2.819
20 DL+LL+ EQ+X + 0.3EQ+Z 10.949 6765.821 -0.001 -1.37 0.022 -16.347
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 21 DL+LL+ EQ-X + 0.3EQ-Z 2.496 1147.281 0.068 -0.202 -0.011 -3.534
1727 21 DL+LL+ EQ-X + 0.3EQ-Z 2.436 1137.926 -0.92 -0.875 -0.085 -3.346
1728 21 DL+LL+ EQ-X + 0.3EQ-Z 0.893 1113.704 0.166 0.439 0.106 -2.157
1729 21 DL+LL+ EQ-X + 0.3EQ-Z 2.59 1120.895 0.134 -0.127 0.001 -2.637
1730 21 DL+LL+ EQ-X + 0.3EQ-Z 0.673 1107.116 0.267 -0.451 -0.083 -1.854
1731 21 DL+LL+ EQ-X + 0.3EQ-Z 1.861 1138.899 0.284 -0.154 0.094 -2.819
21 DL+LL+ EQ-X + 0.3EQ-Z 10.949 6765.821 -0.001 -1.37 0.022 -16.347
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 22 DL+LL+ EQ+Z + 0.3EQ+X 2.496 1147.281 0.068 -0.202 -0.011 -3.534
1727 22 DL+LL+ EQ+Z + 0.3EQ+X 2.436 1137.926 -0.92 -0.875 -0.085 -3.346
1728 22 DL+LL+ EQ+Z + 0.3EQ+X 0.893 1113.704 0.166 0.439 0.106 -2.157
1729 22 DL+LL+ EQ+Z + 0.3EQ+X 2.59 1120.895 0.134 -0.127 0.001 -2.637
1730 22 DL+LL+ EQ+Z + 0.3EQ+X 0.673 1107.116 0.267 -0.451 -0.083 -1.854
1731 22 DL+LL+ EQ+Z + 0.3EQ+X 1.861 1138.899 0.284 -0.154 0.094 -2.819
22 DL+LL+ EQ+Z + 0.3EQ+X 10.949 6765.821 -0.001 -1.37 0.022 -16.347
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 23 DL+LL+ EQ-Z + 0.3EQ-X 2.496 1147.281 0.068 -0.202 -0.011 -3.534
1727 23 DL+LL+ EQ-Z + 0.3EQ-X 2.436 1137.926 -0.92 -0.875 -0.085 -3.346
1728 23 DL+LL+ EQ-Z + 0.3EQ-X 0.893 1113.704 0.166 0.439 0.106 -2.157
1729 23 DL+LL+ EQ-Z + 0.3EQ-X 2.59 1120.895 0.134 -0.127 0.001 -2.637
1730 23 DL+LL+ EQ-Z + 0.3EQ-X 0.673 1107.116 0.267 -0.451 -0.083 -1.854
1731 23 DL+LL+ EQ-Z + 0.3EQ-X 1.861 1138.899 0.284 -0.154 0.094 -2.819
23 DL+LL+ EQ-Z + 0.3EQ-X 10.949 6765.821 -0.001 -1.37 0.022 -16.347
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 24 DL+LL+WLX+ -21.192 769.898 0.117 -0.209 -0.026 47.334
1727 24 DL+LL+WLX+ -32.623 950.243 -9.508 -8.678 0.524 55.359
1728 24 DL+LL+WLX+ -33.366 1296.753 6.892 5.275 -0.383 56.067
1729 24 DL+LL+WLX+ -17.809 1488.023 0.106 -0.149 -0.016 43.419
1730 24 DL+LL+WLX+ -33.845 1291.008 -6.348 -5.194 0.375 56.582
1731 24 DL+LL+WLX+ -33.028 950.708 8.741 7.445 -0.548 55.767
24 DL+LL+WLX+ -171.863 6746.633 1.027E-15 -1.51 -0.074 314.528
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 25 DL+LL+WLX- 22.712 1513.982 0.022 -0.192 0.004 -49.418
1727 25 DL+LL+WLX- 37.066 1321.34 5.784 3.962 0.403 -61.877
1728 25 DL+LL+WLX- 35.571 926.406 -8.443 -7.366 -0.508 -60.545
1729 25 DL+LL+WLX- 26.47 743.1 0.163 -0.105 0.017 -53.683
1730 25 DL+LL+WLX- 35.619 918.976 8.765 7.261 0.563 -60.46
1731 25 DL+LL+WLX- 36.323 1322.829 -6.29 -4.786 -0.368 -61.234
25 DL+LL+WLX- 193.761 6746.633 0.001 -1.226 0.111 -347.217
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 26 DL+LL+WLZ+ 4.391 1147.061 -46.783 -74.66 0.057 -6.484
1727 26 DL+LL+WLZ+ -6.482 1495.739 -31.339 -61.358 -0.591 3.936
1728 26 DL+LL+WLZ+ 9.593 1472.649 -30.247 -60.113 0.593 -9.13
1729 26 DL+LL+WLZ+ 0.905 1120.302 -46.891 -74.699 -0.1 0.146
1730 26 DL+LL+WLZ+ -8.333 739.661 -32.806 -64.323 -0.679 5.443
1731 26 DL+LL+WLZ+ 10.874 771.221 -32.688 -63.992 0.665 -10.084
26 DL+LL+WLZ+ 10.948 6746.633 -220.754 -399.145 -0.055 -16.173
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 27 DL+LL+WLZ- 3.924 1145.75 46.917 74.253 -0.08 -6.042
1727 27 DL+LL+WLZ- 11.623 771.395 32.127 62.921 -0.655 -10.836
1728 27 DL+LL+WLZ- -8.071 746.025 33.203 64.303 0.699 5.021
1729 27 DL+LL+WLZ- 0.944 1119.774 47.168 74.456 0.101 0.045
1730 27 DL+LL+WLZ- 9.418 1465.847 30.713 60.114 -0.57 -8.95
1731 27 DL+LL+WLZ- -6.888 1497.843 30.626 60.371 0.605 4.241
27 DL+LL+WLZ- 10.95 6746.634 220.754 396.418 0.1 -16.521
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 2.455 1126.727 0.058 -0.16 -0.009 -3.572
1727 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 2.464 1115.781 -0.817 -0.762 -0.068 -3.462
1728 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 1.023 1090.838 -0.109 0.157 0.088 -2.344
1729 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 2.171 1093.7 0.107 -0.108 0.001 -2.546
1730 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 0.844 1085.256 0.455 -0.177 -0.067 -2.098
1731 28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 1.992 1116.9 0.306 -0.064 0.078 -3.03
28 DL+0.8(LL+ EQ+X + 0.3EQ+Z) 10.949 6629.202 6.245E-17 -1.114 0.023 -17.052
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 2.455 1126.727 0.058 -0.16 -0.009 -3.572
1727 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 2.464 1115.781 -0.817 -0.762 -0.068 -3.462
1728 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 1.023 1090.838 -0.109 0.157 0.088 -2.344
1729 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 2.171 1093.7 0.107 -0.108 0.001 -2.546
1730 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 0.844 1085.256 0.455 -0.177 -0.067 -2.098
1731 29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 1.992 1116.9 0.306 -0.064 0.078 -3.03
29 DL+0.8(LL+ EQ-X + 0.3EQ-Z) 10.949 6629.202 6.245E-17 -1.114 0.023 -17.052
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 2.455 1126.727 0.058 -0.16 -0.009 -3.572
1727 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 2.464 1115.781 -0.817 -0.762 -0.068 -3.462
1728 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 1.023 1090.838 -0.109 0.157 0.088 -2.344
1729 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 2.171 1093.7 0.107 -0.108 0.001 -2.546
1730 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 0.844 1085.256 0.455 -0.177 -0.067 -2.098
1731 30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 1.992 1116.9 0.306 -0.064 0.078 -3.03
30 DL+0.8(LL+ EQ+Z + 0.3EQ+X) 10.949 6629.202 6.245E-17 -1.114 0.023 -17.052
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 2.455 1126.727 0.058 -0.16 -0.009 -3.572
1727 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 2.464 1115.781 -0.817 -0.762 -0.068 -3.462
1728 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 1.023 1090.838 -0.109 0.157 0.088 -2.344
1729 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 2.171 1093.7 0.107 -0.108 0.001 -2.546
1730 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 0.844 1085.256 0.455 -0.177 -0.067 -2.098
1731 31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 1.992 1116.9 0.306 -0.064 0.078 -3.03
31 DL+0.8(LL+ EQ-Z + 0.3EQ-X) 10.949 6629.202 6.245E-17 -1.114 0.023 -17.052
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 32 DL+0.8(LL+WLX+) -16.445 825.047 0.097 -0.166 -0.02 37.087
1727 32 DL+0.8(LL+WLX+) -25.559 965.755 -7.677 -6.994 0.418 43.473
1728 32 DL+0.8(LL+WLX+) -26.403 1237.164 5.272 4.029 -0.303 44.208
1729 32 DL+0.8(LL+WLX+) -14.207 1387.163 0.084 -0.125 -0.012 34.291
1730 32 DL+0.8(LL+WLX+) -26.79 1232.256 -4.837 -3.974 0.298 44.625
1731 32 DL+0.8(LL+WLX+) -25.896 966.467 7.06 6.002 -0.435 43.812
32 DL+0.8(LL+WLX+) -135.3 6613.852 -0.001 -1.228 -0.054 247.496
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 33 DL+0.8(LL+WLX-) 18.683 1419.849 0.02 -0.151 0.003 -40.274
1727 33 DL+0.8(LL+WLX-) 30.186 1262.399 4.548 3.113 0.321 -50.259
1728 33 DL+0.8(LL+WLX-) 28.743 941.119 -6.985 -6.075 -0.402 -49.027
1729 33 DL+0.8(LL+WLX-) 21.228 791.691 0.13 -0.091 0.013 -43.344
1730 33 DL+0.8(LL+WLX-) 28.779 934.864 7.242 5.978 0.449 -48.956
1731 33 DL+0.8(LL+WLX-) 29.58 1263.931 -4.955 -3.774 -0.29 -49.736
33 DL+0.8(LL+WLX-) 157.199 6613.853 -3.5041E-16 -1 0.094 -281.596
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 34 DL+0.8(LL+WLZ+) 3.958 1126.561 -37.417 -59.692 0.045 -5.915
1727 34 DL+0.8(LL+WLZ+) -4.665 1401.798 -25.211 -49.133 -0.472 2.358
1728 34 DL+0.8(LL+WLZ+) 7.977 1377.759 -24.498 -48.269 0.477 -7.919
1729 34 DL+0.8(LL+WLZ+) 0.835 1093.234 -37.511 -59.731 -0.08 -0.337
1730 34 DL+0.8(LL+WLZ+) -6.354 791.517 -25.948 -51.236 -0.543 3.735
1731 34 DL+0.8(LL+WLZ+) 9.198 822.985 -26.018 -51.097 0.534 -8.838
34 DL+0.8(LL+WLZ+) 10.949 6613.854 -176.603 -319.158 -0.039 -16.916
Node L/C Force-X kN Force-Y kN Force-Z kN Moment-X kNm Moment-Y kNm Moment-Z kNm
1726 35 DL+0.8(LL+WLZ-) 3.583 1125.511 37.53 59.37 -0.064 -5.558
1727 35 DL+0.8(LL+WLZ-) 9.808 822.781 25.567 50.236 -0.523 -9.449
1728 35 DL+0.8(LL+WLZ-) -6.143 796.921 26.266 51.209 0.561 3.393
1729 35 DL+0.8(LL+WLZ-) 0.868 1092.813 37.731 59.523 0.081 -0.421
1730 35 DL+0.8(LL+WLZ-) 7.834 1372.007 24.87 48.26 -0.456 -7.771
1731 35 DL+0.8(LL+WLZ-) -5.003 1403.82 24.639 48.341 0.485 2.614
35 DL+0.8(LL+WLZ-) 10.947 6613.853 176.603 316.939 0.084 -17.192
GVPR ENGINEERS LIMITED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date Rev
TITLE
(Zone-C) UTTAR PRADESH 3/19/2021 A
8.0) DESIGN OF STAIRCASE
8.1) Design of Staircase Flight-1 to 14
Design of waist slab
Staircase is carried on staging columns
staircase is from GL to Mid landing beam
Riser of staircase, R = = 185.00 mm
Tread of staircase, T = = 300.00 mm
Width of staircase = = 1000 mm
Assume thickness of waist slab = = 150 mm
Clear cover to reinforcement = = 30 mm
Grade of Concrete, fck = = 30 N/mm2
Grade of steel, fy = = 500 N/mm2
Loads
Live load acting on the staircase = = 3 kN/m2
Inclined length of each step = b = SQRT(R*R+T*T)/T = 1.175
1) Self weight of RCC step = 0.5 x 185/1000 x 25 = = 2.310 kN/m2
2) Self weight of waist slab = 0.15* 25* 1.175 = 4.406 kN/m2
Total dead load acting = 4.41+ 2.31 = 6.716 kN/m2
Total load on waist slab = 6.72+ 3 = 10.000 kN/m2
Effective span of flight = 3.525 m
Max Bending moment = 10* 3.525* 3.525/ 10
= 12.43 knm
Area of steel required on bottom face of waist slab at span
Mu =1.5 x 12.425625= 18.64 kN-m/m
Diameter of bar provided = 12 mm
Effective depth of slab = 150 - 30 - 6 114 mm
Mu/bd 2
= 1.43 N/mm2
Percentage of steel required = 0.349 %
Area of steel required = 397.86 mm2/m
Minimum area of steel required 0.12/100 x 1000 x 150 = 180 mm2/m
Provide 12 dia @ 150 mm c/c as main steel
Provide 8 dia @ 150 mm c/c as distribution steel
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date Rev
TITLE
(Zone-C) UTTAR PRADESH 3/19/2021 A
Mu =1.5 x 15.5165625= = 23.27 kN-m/m
GVPR ENGINEERS LIMITED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI Date Rev
TITLE
(Zone-C) UTTAR PRADESH 3/19/2021 A
Diameter of bar provided = = 12 mm
= 4.000 no
Shear force
= 17.24 kn
9.0 ANNEXURES
Water & Environment Division
TITLE : RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR PRADESH Date. 3/19/2021
ANNEXURE - A
MOMENT COEFFICIENTS IN CYLINDRICAL WALL,FIXED BASE ,FREE TOP AND SUBJECTED TO TRIANGULAR LOAD
Height of side wall ( H )-mts 3.250 Diameter of container ( D )-mts 10.00 Thickness ( T )- mm 200
OPERATE FIGURES IN RED ONLY
H2/Dt 0.10h 0.20h 0.30h 0.40h. 0.50 h 0.60 h 0.70 h 0.80 H 0.90 h
5.281 0.00017 0.0007 0.0014 0.0026 0.0042066 0.00553 0.0056752 0.0028281 -0.0053223
H2/Dt 0.0 H 0.10 H 0.20 H 0.30 H 0.40 H 0.50 H 0.60 H 0.70 H 0.80 H
0 1 2 3 4 5 6 7 8 9
0.4000 0.4740 0.4400 0.3950 0.3520 0.3080 0.2640 0.2150 0.1650 0.1110
0.8000 0.4230 0.4020 0.3810 0.3580 0.3300 0.2970 0.2490 0.2020 0.1450
1.2000 0.3500 0.3550 0.3610 0.3620 0.3580 0.3420 0.3090 0.2560 0.1860
1.6000 0.2710 0.3030 0.3410 0.3690 0.3850 0.3850 0.3620 0.3140 0.2330
2.0000 0.2050 0.2600 0.3210 0.3730 0.4110 0.4340 0.4190 0.3690 0.2800
3.0000 0.0740 0.1790 0.2810 0.3750 0.4490 0.5060 0.5190 0.4790 0.3750
4.0000 0.0170 0.1370 0.2530 0.3670 0.4690 0.5450 0.5790 0.5530 0.4470
5.0000 -0.0080 0.1140 0.2350 0.3560 0.4690 0.5620 0.6170 0.6060 0.5030
6.0000 -0.0110 0.1030 0.2230 0.3430 0.4630 0.5660 0.6390 0.6430 0.5470
8.0000 -0.0150 0.0960 0.2080 0.3240 0.4430 0.5640 0.6610 0.6970 0.6210
10.0000 -0.0080 0.0950 0.2000 0.3110 0.4280 0.5520 0.6660 0.7300 0.6780
12.0000 -0.0020 0.0970 0.1970 0.3020 0.4170 0.5410 0.6640 0.7500 0.7200
14.0000 0.0000 0.0980 0.1970 0.2990 0.4080 0.5310 0.6590 0.7610 0.7520
16.0000 0.0020 0.1000 0.1980 0.2990 0.4030 0.5210 0.6500 0.7640 0.7760
1.0 h
10
-0.1205
-0.0795
-0.0602
-0.0505
-0.0436
-0.0333
-0.0268
-0.0222
-0.0187
-0.0146
-0.0122
-0.0104
-0.0090
-0.0079
1.0 h
-0.02122
0.90 H
10
0.0570
0.0760
0.0980
0.1240
0.1510
0.2100
0.2560
0.2940
0.3270
0.3860
0.4330
0.4770
0.5130
0.5360
0.90 H
0.303273
Provided Area
of Steel (mm2)
440.00
440.00
440.00
440.00
440.00
440.00
440.00
440.00
440.00
440.00
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK - DATE REV. No.
PROJECT:
DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA 3/19/2021 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR DESIGNED CHECKED
TITLE :
PRADESH PSD DHC
Spacing of Hoops :
Spacing not more than following :
1.) 1/4 of Minimum Member Dimension = 112.5 mm
2.) 6 times the dia smaalest longitudinal reinforecement = 120 mm
3.) 100 = 100 mm
Provide Spacing of Hoops, S = 90 mm
1 Area of C/S of bar forming circular hoop is Ash = 0.09 Sv Dk fck/fy ((Ag/Ak)-1)
Ash = 0.09 * 90*380*(30/500)*((158962.5/113354)-1) = 74.31 mm2
2 Area of C/S of bar forming circular hoop is Ash = 0.024 Sv Dk fck/fy
Ash = 0.024 * 90*380*(30/500) = 49.25 mm2
Maximum of 1 and 2 = 74.31 mm2
Provided C/S of bar forming hoop = 78.54 mm2
Provided hoop bar of dia 10mm is O.K
Thus Circular Hoops of Dia 10mm at a spacing of 90mm c/c will be adequate.
Hencce Provide the confining reinforcement over a height of 600 mm from face of the Joint.
GVPR ENGINEERS LIMITED
CONSTRUCTION OF PIPE WATER SUPPLY SCHEME in JHILO GROUP OF VILAGES BLOCK - DATE REV. No.
PROJECT:
DUDDHI, BABHANI AND MYORPUR DISTRICT -SONBHADRA 3/19/2021 A
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) UTTAR DESIGNED CHECKED
TITLE :
PRADESH PSD DHC
Transverse Reinforcement:
Diameter of Lateral ties:
The dia of lateral ties shall not be less than the following,
1 1/4 th of dia of largest longitudinal bar = 5 mm
2 6 mm = 6 mm
Required dia of lateral ties (Maximum of 1 & 2) = 6 mm
However Provide Dia of Lateral tie = 8 mm
Spacing of Lateral ties:
Shall not be more than least of the following
1 The least lateral dimension of compression member = 450 mm
2 16 times the smallest dia of longitudinal reinforcement = 320 mm
= 300 mm
Required Pitch of lateral ties = 300 mm
However Provide Pitch of Lateral tie = 150 mm
Provide 8 dia ties @150mm c/c
GVPR ENGINEERS LIMITED
RCC DETAILS OF 250 KL OHSR WITH 25 M STAGING AT KARAM GHATI (Zone-C) DESIGNED CHECKED
TITLE :
UTTAR PRADESH PSD DHC
The first hoop shall be at a distance not exceeding 50 mm from the joint face. Vertical hoops at
the same spacing as above, shall also be provided over a length equal to 2d on either side of a
section where flexural yielding may occur under the effect of earthquake forces. Elsewhere, the
beam shall have vertical hoops at a spacing not exceeding d/2.
The spacing of hoops over a length of 2d at either ends of a beam shall not exceed
d/4
8 times the diameter of the smallest longitudinal bar and
(a) d/4 = 113.55 mm
(b) 8 times the diameter of the smallest longitudinal bar = 128 mm
(c) 100 mm = 100 mm
The spacing of hoops over a length of 2d at either end of a beam shall be provided is
Min (113.55,128,100) = 100 mm
Provide Spacing at Supports = 100 mm
Elsewhere, the beam shall have vertical hoops at a spacing not exceeding d/2.
d/2 = 227.1 mm
Elsewhere, the beam shall have vertical hoops at a spacing of 200 mm
Stirrups :