Professional Documents
Culture Documents
Sist en 754 2 2017
Sist en 754 2 2017
SIST EN 754-2:2017
01-januar-2017
1DGRPHãþD
SIST EN 754-2:2014
$OXPLQLMLQDOXPLQLMHYH]OLWLQH+ODGQRYOHþHQHSDOLFHGURJRYLLQFHYLGHO
0HKDQVNHODVWQRVWL
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical
properties
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 754-2:2017
English Version
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
iTeh STANDARD PREVIEW
Centre has the same status as the official versions.
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 754-2:2016 E
worldwide for CEN national Members.
SIST EN 754-2:2017
EN 754-2:2016 (E)
Contents Page
European foreword....................................................................................................................................................... 3
1 Scope .................................................................................................................................................................... 4
2 Normative references .................................................................................................................................... 4
3 Mechanical property limits ......................................................................................................................... 4
3.1 General ................................................................................................................................................................ 4
3.2 Elongation .......................................................................................................................................................... 4
3.3 Reference list of the tables of mechanical properties of the relevant aluminium and
aluminium alloys ............................................................................................................................................. 5
3.4 Detailed tables of mechanical properties............................................................................................... 6
Annex A (informative) List of tempers used in Tables 1 to 37 .................................................................... 37
Bibliography ................................................................................................................................................................. 39
2
SIST EN 754-2:2017
EN 754-2:2016 (E)
European foreword
This document (EN 754-2:2016) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be
withdrawn at the latest by May 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
CEN/TC 132 affirms its policy that if a patentee refuses to grant licenses on standardized products
under reasonable and not discriminatory conditions, this product will be removed from the
corresponding document.
EN 754 comprises the following parts under the general title "Aluminium and aluminium alloys — Cold
drawn rod/bar and tube":
iTeh STANDARD PREVIEW
— Part 1: Technical conditions for inspection and delivery
—
(standards.iteh.ai)
Part 2: Mechanical properties
SIST EN 754-2:2017
— Part 3: Round bars, tolerances on dimensions and form
https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
2b39d91cf792/sist-en-754-2-2017
— Part 4: Square bars, tolerances on dimensions and form
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3
SIST EN 754-2:2017
EN 754-2:2016 (E)
1 Scope
This European Standard specifies the mechanical property limits resulting from tensile testing
applicable to aluminium and aluminium alloy cold drawn rod/bar and tube.
Technical conditions for inspection and delivery, including product and testing requirements, are
specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for
these materials are given in EN 573-3.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 754-1:2016, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 1: Technical
conditions for inspection and delivery
EN ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature (ISO
6892-1)
Brinell hardness values given in Table 1 to Table 37 expressed as HBW values are for information only.
3.2 Elongation
The A value for elongation is the % elongation measured over a gauge length of 5, 65 S0 (where S0 is
the initial cross-sectional area of the test-piece), and expressed in percent.
For certain products the supplier may choose (if not otherwise specified in the order documents) to use
the elongation based on A50mm. Consequently, values for the A50mm are included in the following tables.
The A50mm value is the elongation measured over a gauge length of 50 mm and expressed in percent.
Test pieces and their location in the specimen are given in EN 754-1.
4
SIST EN 754-2:2017
EN 754-2:2016 (E)
3.3 Reference list of the tables of mechanical properties of the relevant aluminium and
aluminium alloys
Page
Table 1 : Aluminium EN AW-1050A [Al 99,5] 6
Table 2 : Aluminium EN AW-1200 [AI 99,0] 7
Table 3 : Alloy EN AW-2007 [Al Cu4PbMgMn] 8
Table 4 : Alloy EN AW-2011 [AI Cu6BiPb] 9
Table 5 : Alloy EN AW-2011A [AI Cu6BiPb(A)] 10
Table 6 : Alloy EN AW-2014 [AI Cu4SiMg] 11
Table 7 : Alloy EN AW-2014A [AI Cu4SiMg(A)] 12
Table 8 : Alloy EN AW-2017A [AI Cu4MgSi(A)] 13
Table 9 : Alloy EN AW-2024 [AI Cu4Mg1] 14
Table 10 : Alloy EN AW-2030 [AI Cu4PbMg] 15
Table 11 : Alloy EN AW-3003 [AI Mn1Cu] 16
Table 12 : Alloy EN AW-3103 [AI Mn1] 17
Table 13 : Alloy EN AW-5005 [AI Mg1(B)] 18
iTeh STANDARD PREVIEW
Table 14 : Alloy EN AW-5005A [AI Mg1(C)] 18
Table 15 :
(standards.iteh.ai)
Alloy EN AW-5019 [AI Mg5] 19
Table 16 : Alloy EN AW-5049 SIST EN 754-2:2017[Al Mg2Mn0,8] 20
https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
Table 17 : Alloy EN AW-5251 [AI Mg2Mn0,3]
2b39d91cf792/sist-en-754-2-2017 21
Table 18 : Alloy EN AW-5052 [AI Mg2,5] 22
Table 19 : Alloy EN AW-5154A [AI Mg3,5(A)] 23
Table 20 : Alloy EN AW-5754 [AI Mg3] 24
Table 21 : Alloy EN AW-5083 [AI Mg4,5Mn0,7] 25
Table 22 : Alloy EN AW-5086 [AI Mg4] 26
Table 23 : Alloy EN AW-6012 [AI MgSiPb] 27
Table 24 : Alloy EN AW-6026 [AI MgSiBi] 27
Table 25 : Alloy EN AW-6060 [AI MgSi] 28
Table 26 : Alloy EN AW-6061 [AI Mg1SiCu] 29
Table 27 : Alloy EN AW-6262 [AI Mg1SiPb] 30
Table 28 : Alloy EN AW-6262A [AI Mg1SiSn] 30
Table 29 : Alloy EN AW-6063 [AI Mg0,7Si] 31
Table 30 : Alloy EN AW-6063A [AI Mg0,7Si(A)] 32
Table 31 : Alloy EN AW-6064A [AI Mg1SiBi] 33
Table 32 : Alloy EN AW-6065 [AI Mg1Bi1Si] 33
Table 33 : Alloy EN AW-6082 [AI Si1MgMn] 34
5
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
Da Sb min. max. min. max. min. min. value
O, H111 ≤ 80 ≤ 60 60 95 - - 25 22 20
H14 ≤ 40 ≤ 10 100 135 70 - 6 5 30
H16 ≤ 15 ≤5 120 160 105 - 4 3 35
H18 ≤ 10 ≤3 145 - 125 - 3 3 43
Drawn tube iTeh STANDARD PREVIEW
Wall thickness (standards.iteh.ai)
R R m A p0,2 A50mm HBW
Temper t MPa MPa % % Typical
SIST EN 754-2:2017
min. max. min. max.
mm https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
min. min. value
O, H111 ≤ 20 60 2b39d91cf792/sist-en-754-2-2017
95 - - 25 22 20
H14 ≤ 10 100 135 70 - 6 5 30
H16 ≤5 120 160 105 - 4 3 35
H18 ≤3 145 - 125 - 3 3 43
a D = Diameter for round bar.
b S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
6
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
min. min. value
Da Sb min. max. min. max.
O, H111 ≤ 80 ≤ 60 70 105 - - 20 16 23
H14 ≤ 40 ≤ 10 110 145 80 - 5 4 37
H16 ≤ 15 ≤5 135 170 115 - 3 3 45
H18 ≤ 10 ≤3 150 - 130 - 3 3 50
Drawn tube
O, H111 ≤ 20 70 105 - - 20 16 23
H14 ≤ 10 110 145 80 - 5 4 37
H16 iTeh STANDARD
≤5 135 170 PREVIEW
115 - 3 3 45
H18 ≤3 150 - 130
(standards.iteh.ai) - 3 3 50
a D = Diameter for round bar.
SIST EN 754-2:2017
b S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
2b39d91cf792/sist-en-754-2-2017
7
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
Da Sb min. max. min. max. min. min. value
≤ 30 ≤ 30 370 240 7 5 95
T3 c - -
30 < D ≤ 80 30 < S ≤ 80 340 220 6 - 95
T3 c ≤ 20 370 - 250 - 7 5 95
T3510
≤ 20 370 - 240 - 5 3 95
T3511 c iTeh STANDARD PREVIEW
a D = Diameter for round bar.
(standards.iteh.ai)
b S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
SIST EN 754-2:2017
c Properties may be obtained by press quenching.
https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
2b39d91cf792/sist-en-754-2-2017
8
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
min. min. value
Da Sb min. max. min. max.
≤ 40 ≤ 40 320 - 270 - 10 8 90
T3 40 < D ≤ 50 40 < S ≤ 50 300 - 250 - 10 - 90
50 < D ≤ 80 50 < S ≤ 80 280 - 210 - 10 - 90
T8 ≤ 80 ≤ 80 370 - 270 - 8 6 115
Drawn tube
Wall thickness Rm Rp0,2 A A50mm HBW
Temper t MPa MPa % % Typical
min. max. min. max. value
mm min. min.
≤5 310 - 260 - 10 8 90
T3 c
5 < t ≤ 20 290 - 240 - 8 6 90
T8 ≤ 20 STANDARD
iTeh 370 - PREVIEW
275 - 8 6 115
a D = Diameter for round bar.
b
(standards.iteh.ai)
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
SIST EN 754-2:2017
Properties mayhttps://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
be obtained by press quenching.
2b39d91cf792/sist-en-754-2-2017
9
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
Da Sb min. max. min. max. value
min. min.
≤ 40 ≤ 40 320 - 270 - 10 8 90
T3 40 < D ≤ 50 40 < S ≤ 50 300 - 250 - 10 - 90
50 < D ≤ 80 50 < S ≤ 80 280 - 210 - 10 - 90
T8 ≤ 80 ≤ 80 370 - 270 - 8 6 115
Drawn tube
Wall thickness Rm Rp0,2 A A50mm HBW
Temper t MPa MPa % % Typical
mm min. max. min. max. min. min. value
≤5 310 - 260 - 10 8 90
T3 c
5 < t ≤ 20 290 - 240 - 8 6 90
T8 ≤ 20iTeh STANDARD
370 - 275 PREVIEW
- 8 6 115
a D = Diameter for round bar. (standards.iteh.ai)
b S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
SIST EN 754-2:2017
c Properties may be obtained by press quenching.
https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
2b39d91cf792/sist-en-754-2-2017
10
SIST EN 754-2:2017
EN 754-2:2016 (E)
Drawn rod/bar
Dimensions Rm Rp0,2 A A50mm HBW
Temper mm MPa MPa % % Typical
Da Sb min. max. min. max. min. min. value
O, H111 ≤ 20 (standards.iteh.ai)
- 240 - 125 12 10 45
T3 ≤ 20 380 -
SIST EN 754-2:2017 290 - 8 6 110
T3510, https://standards.iteh.ai/catalog/standards/sist/03881ef3-129b-4566-96f7-
≤ 20 380 - 290
2b39d91cf792/sist-en-754-2-2017 - 6 4 110
T3511
T4 ≤ 20 380 - 240 - 12 10 110
T4510,
≤ 20 380 - 240 - 10 8 110
T4511
T6 ≤ 20 450 - 380 - 8 6 140
T6510,
≤ 20 450 - 380 - 6 4 140
T6511
a D = Diameter for round bar.
b S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
11