Professional Documents
Culture Documents
SVI II AP Digital Upgrade Procedure
SVI II AP Digital Upgrade Procedure
Applicable To:
Topic: Firmware
© 2016 General Electric Company. All rights reserved. Masoneilan Knowledge Base =| 1
Once GE’s Masoneilan receives your PO they e-mail the upgrade key and this upgrade
instruction document. The upgrade key is unique to the PO and upgrade part number. Save
this number as it is critical for “Part II Upgrade Procedure”.
NOTE The serial and part numbers are very small. Double check to
ensure accuracy.
If the electronics module was replaced in the field, then the unit
must be opened to retrieve the serial number off the electronics
module (not from SVI II AP tag).
2. E-mail the device file or written data from Step 1, along with the upgrade key obtained in
“Part I Order Entry”, to software.reg@ge.com.
3. Receiving the option file: On receipt of the e-mail, GE’s Masoneilan sends the option file
(.opt) to the sender’s e-mail address. Save the file in a folder so that it is accessible from
Smarts Assistant Standard Software.
4. Upgrading the unit. Refer to “Part II Upgrade Procedure”. This step requires a PC with
Smarts Assistant Standard Software connected to SVI II AP via a HART modem.
WARNING This procedure can be performed in any mode and causes a warm
reset on the device which may cause the valve to move. Therefore,
if performed while the valve in service, there could be a
momentary process disturbance.
If you require any assistance, contact the Digital Product Help desk at 1-888-SVI-LINE (North
America).
2 | =GE Oil & Gas © 2016 General Electric Company. All rights reserved.
Save the Existing Device Configuration
Use Smarts Assistant Standard software to generate the device file. If you do not have Smarts
Assistant, download it from:
http://www.ge-mcs.com/en/download.html
1. Connect to the device.
© 2016 General Electric Company. All rights reserved. Masoneilan Knowledge Base =| 3
2. Click on the Options tab.
3. Click on Create Device File and save the device file to a location.
4 | =GE Oil & Gas © 2016 General Electric Company. All rights reserved.
4. E-mail the device file and Upgrade Key to GE’s Masoneilan.
http://www.ge-mcs.com/en/download.html
1. Connect to the device.
© 2016 General Electric Company. All rights reserved. Masoneilan Knowledge Base =| 5
2. Click on the Options tab.
6 | =GE Oil & Gas © 2016 General Electric Company. All rights reserved.
Emailed the original options file, then the new options file includes the original options
plus the upgrade.
Did not email the old file, then the new options file includes what GE has as the original
options plus the upgrade.
In either case, this populates into the Options tab when the new file is loaded.
6. Click Change Options. If this button is greyed out, contact technical support at
svisupport@ge.com or call 1-888-SVI-LINE.
7. Click the Connection tab and click Disconnect.
© 2016 General Electric Company. All rights reserved. Masoneilan Knowledge Base =| 7
Figure 10 Digital Field Upgrade Process
8 | =GE Oil & Gas © 2016 General Electric Company. All rights reserved.
Warranties and Disclaimers
ValVue, SVI, SVI II and HDLT are marks owned by GE Oil & Gas Inc. All other marks are the property of their respec-
tive owners. While this information is presented in good faith and believed to be accurate, GE Oil & Gas does not
guarantee satisfactory results from reliance upon such information. NOTHING INCLUDED HEREIN CAN BE CON-
STRUED AS A WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE PERFORMANCE, MERCHANTABIL-
ITY, FITNESS, OR OTHER MATTER WITH RESPECT TO THE PRODUCTS, NOR AS A RECOMMENDATION TO USE ANY
PRODUCT OR PROCESS IN CONFLICT WITH ANY PATENT GE Oil & Gas reserves the right, without express notice, to
alter or improve the designs or specifications of the products described herein.
© 2016 General Electric Company. All rights reserved. Masoneilan Knowledge Base =| 9
This page intentionally left blank.