Professional Documents
Culture Documents
Intrinsically Safe Valves
Intrinsically Safe Valves
Solenoid Operators
WBIS: Watertight, Type 3, 3S, 4, 4X, IP-67 Ordering Information
Liquid Crystal Polymer (LCP) overmolded with 1/2” NPT conduit The LCP Intrinsically Safe solenoid enclosure is designated
connection and screw terminals for simple wiring. The terminal by the prefix, “WBIS”. The Epoxy Din Connector is ordered by
block will accommodate 18 gage (AWG) wire and grounding screw prefix, “ISSC”.
is located inside the enclosure. Example: WBIS8314A300 Spare Coil P/Ns
ISSC: DIN 43650/ISO 4400, IP-65 ISSC8314A300 WBIS: 274445-001*
Epoxy overmolded with Din Connector supplied, suitable to accept ISSC: 268976-001*
wiring cable diameters of 0.310 to 0.400 inches. Nominal Ambient Temperature Ranges:
Solenoid Construciton Series 8314, 8262, 8317:
-40˚F to 140˚F (-40˚C to 60˚C)
Gasket Cover NBR
Cover Screw 18-8 Stainless Steel Series 8223, 8316, 8344, 8345, 8551:
Cover Screw Gasket NBR
-4˚F to 140˚ F (-20˚C to 60˚C)
Sleeve 430F Stainless Steel Series 8316 suffix V
Nameplate Stainless Steel 32˚F to 140˚F (0˚C to 60˚C)
Burp Cap Assembly PA/NE Refer to Engineering Section for details.
Valve Construction Approvals:
Valve Parts in Contact with Fluids FM approved under J.I.3W8A8. AX (3610).
Body Brass Stainless Steel Aluminum CSA certified under File LR-13976-116C.
CENELEC EEx ia IIC T6 approved - pending
Seals, Discs NBR NBR/PUR
Meets applicable CE directives.
Sleeve 304L Stainless Steel 304L Stainless Steel Refer to Engineering Section for details.
Core and Plugnut 430F Stainless Steel 430F Stainless Steel
Springs 302 Stainless Steel 302 Stainless Steel Important:
Rider Rings PTFE PTFE These solenoids are intended for use on clean, dry air or inert
Spring Retainer CA CA gas filtered to 50 micrometers or better. To prevent freezing, the
Piston Assembly 8223 SS/NBR NA dew point of the media should be at least 18˚F (-8˚C) below the
Piston Assembly 8345 PA/NBR NA minimum temperature to which any portion of the clean air or
gas system could be exposed. Instrument air in compliance
8344 Internals Brass/300 Stainless Steel NA
with ANSI/ISA Standard S7.3-1975 (R1981) exceeds the above
8316 Internals NBR/Stainless Steel FKM/Stainless Steel NA requirements and is, therefore, an acceptable medium for
8551 Internals NA PA/FV, AL, CA, Steel these valves.
Direct Mount 8551 NAMUR Specifications (Convertible 3/2 and 5/2 valve)
Single Solenoid Dual Solenoid
Operating Operating
Pressure Max. Pressure Max.
Differential (psi) Fluid Anodized Differential (psi) Fluid Anodized
Pipe Orifice Air-Inert Gas Temp.˚F Aluminum Body Constr. Air-Inert Gas Temp. ˚F Aluminum Body Constr.
Size Size Cv Flow 24/DC Ref. 24/DC Ref.
(ins.) (ins.) Factor Min. Max. Only Catalog Number No. Min. Max. Only Catalog Number No.
1/4 ➀ 1/4 .7 30 150 140 WBIS8551A301 19 30 150 140 WBIS8551A302 20
Direct Mount 8551 NAMUR - Stainless Steel 5/2 valves
1/4 1/4 .7 30 150 140 WBIS8551A388 21 30 150 140 WBIS8551A390 22
5.04 R3
SERIES
Intrinsically
Safe
4
Specifications (Metric units)
2/2 VALVES, NORMALLY CLOSED, with NBR Disc
Operating Pressure
Differential (bar)
Pipe Orifice Kv Flow Air-Inert Gas Brass Body Stainless Steel Body
Size Size Factor Max. Fluid and Constr. Constr.
(ins.) (mm) (m3/h) Min. Max. Ambient Temp. ˚C Catalog Number Ref. No. Ref. No.
1/4 1 .07 0 10.3 59 WBIS8262A320 1 WBIS8262A386 1A
3/8 8 1.29 0.7 10.3 59 WBIS8223A323 2 - -
1/2 10 2.74 1.7 10.3 59 WBIS8223A303 3 WBIS8223A310 3
3/2 VALVES
Operating Pressure
Kv Flow Differential (bar)
Factor
Pipe Orifice (m3/h) Air-Inert Gas Brass Body Stainless Steel Body
Size Size Pressure to Cylinder to Max. Fluid and Constr. Constr.
(ins.) (ins.) Cylinder Exhaust Min. Max. Ambient Temp. ˚C Catalog Number Ref. No. Catalog Number Ref. No.
UNIVERSAL OPERATION (Pressure at any port) with NBR Disc
1/4 2 .07 .07 0 10.3 59 WBIS8314A300 4 WBIS8314A301 4A
NORMALLY CLOSED (Closed when de-energized)
1/4 8 1.29 1.29 ➅ 10.3 59 WBIS8316A301 ➂ 5 WBIS8316A381V ➄ 8
3/8 8 1.54 1.54 ➅ 10.3 59 WBIS8316A302 ➂ 5 WBIS8316A382V ➄ 8
3/8 16 3.43 3.43 ➅ 10.3 59 WBIS8316A303 ➂ 6 - -
1/2 16 3.43 3.43 ➅ 10.3 59 WBIS8316A304 ➂ 6 WBIS8316A384V ➄ 9
3/4 17 4.71 4.71 0.7 10.3 59 WBIS8316A374 ➂ 7 - -
1 25 11.14 11.14 0.7 10.3 59 WBIS8316A334 ➂ 7A - -
UNIVERSAL OPERATION (Normally Closed or Normally Open) "Quick Exhaust" with CR Diaphragm and NBR Disc
1/4 ➁ .07 .63 0.3 10.3 59 WBIS8317A307 ➀ 10 WBIS8317A308➀ 11
4/2 VALVES, with NBR Disc and Seal
1/4 2 .07 .07 0.7 10.3 59 WBIS8345A301 ➀➂ 12 WBIS8345A381 ➀➂ 12
Constr. Constr.
4/2 VALVES, Brass Body with NBR Disc Single Solenoid Ref. No. Dual Solenoid Ref. No.
1/4 6 .69 .86 0.7 10.3 59 WBIS8344A370 ➀➂ 13 WBIS8344A344 ➂ 16
3/8 10 1.20 1.89 0.7 10.3 59 WBIS8344A372 ➀➂ 14 WBIS8344A380 ➂ 17
1/2 10 1.20 1.89 0.7 10.3 59 WBIS8344A374 ➀➂ 14 WBIS8344A382 ➂ 17
3/4 19 4.46 4.80 0.7 10.3 59 WBIS8344A376 ➀➂ 15 WBIS8344A354 ➂ 18
1 19 4.46 4.80 0.7 10.3 59 WBIS8344A378 ➀➂ 15 WBIS8344A356 ➂ 18
➀ There are two exhaust flows in the exhaust mode (pilot and main). The
Notes: ➄ Diaphragm and main disc FKM only
pilot exhaust must be connected to the main exhaust when the air or inert
(pilot is low-temperature NBR).
gas cannot be exhausted to atmosphere.
➅ Zero minimum when valve selection gasket is in external position
➁ For “Quick Exhaust” valves, pressure port is 1/16", exhaust port is 1/4".
and proper auxiliary air pressure is applied. See chart on page
➂ IMPORTANT: A minimum operating pressure differential must be
5.14 for auxiliary pressure vs. mainline pressure. Minimum 1 bar
maintained between the pressure and exhaust ports. Supply and exhaust
Operating Pressure Differential when selection gasket is in the
piping must be full area, unrestricted. ASCO flow controls and other
internal position.
similar components must be installed in the cylinder lines only.
5.05 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 1, 1A
Constr. Ref. 2
5.06 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 3
Constr. Ref. 4, 4A
5.07 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 5
Constr. Ref. 6
5.08 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 7, 7A
Constr. Ref. 8
5.09 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 9
Constr. Ref. 10
5.10 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 11
Constr. Ref. 12
5.11 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 19
5.12 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 20
Constr. Ref. 21
5.13 R3
SERIES
Intrinsically
Safe
4
Dimensions: inches (mm)
Constr. Ref. 22
120
106
PILOT LINE PRESSURE (psi)
90
75
60
45
30
15
0
0 15 30 45 60 75 90 105 120 135 150
MAINLINE PRESSURE (psi)
5.14 R3