Professional Documents
Culture Documents
Ata 34
Ata 34
Which common display system (CDS) indications show no computed data (NCD) when the air
data inertial reference unit (ADIRU) is in the align mode?
A. Airspeed and Altitude
B. Heading and track data
C. Only Altitude
2. If the Transponder Mode Selector turned to stndy By;
A. ground discrete prevents operation of the transponder
B. active transponder responds to ATC interrogations.
C. active transponder responds to ATC interrogations. The reply does not contain an altitude
report.
3. For which of the following condition the ATC fail lights comes on
A. Transponder failure and Antenna failure
B. Control data failure and Altitude input failure.
C. Both A and B are correct.
4. Which of the following causes wxr failure display?
A. WXR R/T and WXR antenna
B. WXR control panel
C. All
5. What causes amber IAS DISAGREE message on the captains and first officers
Displays?
A. left and right airspeed indications disagree by 5 knots or more
B. left and right airspeed indications disagree by 2 knots or more
C. left and right airspeed indications disagree by 1 knots or more
B. False
34. localizer antenna is used when ILS frequency is tuned and APP is selected on MCP?
35. Location of Localizer antenna switch is in ____________?
36. Suppose that you are operating radar, what happen if there are large metallic objects closer
to WXR radar radiation by less than 200 feet for the 180-degree area in front Of the airplane
A. Damage to the transceiver Could occur if objects are in this area
B. Rf energy can cause injuries to persons
C. This can cause explosion
37. How many alert messages are shown when wxr radar process unsatisfactory data?
38. What is the function of WXR radar pedestal switches?
39. If you want to turn off the WXR radar R/T, which control panel and which swich you
will use?
40. When you enter position data (on IRS display unit) that is more than 1 degree different than the
recorded latitude or 1 degree different than the recorded longitude, what will happen?
A. ALIGN light flashes
B. Status code 4 shows on ISDU and ENTER IRS POSITION shows on CDU
C. Both are correct
_______________,______________________
44. Amber BELOW GLIDESLOPE lights, come on for_________
A. a mode 5 alert
B. a mode 6 alert
C. a mode 7 alert
45. The PULL UP warning annunciation shows for ____________
A. mode 1, 2, 3 and54 conditions.
B. mode 1, 2, 3 and 4 conditions.
C. mode 1, 2, 3 and 6 conditions.
46. The WINDSHEAR warning annunciation shows for ______
A. a mode 6 condition
B. a mode 7 condition
C. a mode 1,2,3,4, condition
47. On EFIS control panel the maximum range for terrain data selection is___________
A. 640 nautical miles
B. 320 nautical miles
C. 5 nautical miles
48. The terrain weather relay 745 J24 box is located in____________
A. in the nose wheel well on the right side and behind the forward access panel
B. in the forward cargo compartment
C. in the main landing gear wheel well on the right side
49. the left side and behind the forward access panel. GPWS visual warnings show on the
_____________,____________________,____________
50. If the ADIRU detects airplane movement during the alignment mode, the alignment process will
________
A. Stop, After the motion stops, a new alignment will start
B. The motion does not affect, the alignment
C. New alignment will be automatically restart while the aircraft is kept in motion
51. ADIRU sends ______________,_____________,________________,__________ data to SMYD
1
52. ADIRU sends ADR data to cabin pressure controller (CPC) 1 and 2 to calculate pressurization
values, list the three values that ADIRU send to CPC1 AND
CPC2._____________,____________,_____________
53. In case there is no AC power from all available generators, and IRS is on, DC power
will be supplied to
a. Left and Right ADIRU for 5 minutes
b. Only Right ADIRU for 5 minutes
c. Left ADIRU and for 5 minutes to Right ADIRU
54. The total number of ADM ( air data module) on this aircraft is
a. 3
b. 4
c. 5
55. You can turn on the inertial reference system from
a. ISDU
b. MSU
c. IRS master caution unit
56. Total Air Temperature is indicated on
a. PFD
b. ND
c. Engine Primary display
57. Radio altimeter is displayed on
a. PFD
b. ND
c. Both
60. How can we regulate the audio volume level coming out of the cockpit speakers?
a. Using the listen switch (rotating knob ) on ACP
b. Using mick select switch on ACP
61. Both choice A and B are correctCabin differential pressure indicator gets its input
from
a. ADIRU 1
b. ADM
c. Alternate static port
62. Alternate static drain is found in the
d. Forward cargo compartment
e. EE compartment
f. In the forward equipment compartment
63. In case there is no AC power from all available generators, and IRS is on, DC power
will be supplied to
a. Left and Right ADIRU for 5 minutes
b. Only Right ADIRU for 5 minutes
c. Left ADIRU and for 5 minutes to Right ADIRU
66. The variation time it takes for the alignment of ADIRU depends on
a. Longitude of earth
b. Latitude of earth
c. Both
68. Each angle of attack sensor has 2 resolvers in side, and their output goes to
____________________& ________________________.
69. On the MSU the Inertial Reference switch is ‘off’. Yet you can see one of this on
DU’S (PFD or ND)
a. Altitude
b. Vertical speed
c. Heading
71. Present position can be entered in different ways. Write at least five
72. When performing a test on ADIRU, you see the test output on one of the following,
except on
a. PFD
b. ND
c. both
77. The interlock circuit in the weather radar transceiver, before radiating signal,
makes sure that
a. The EFIS control panel is installed
b. The Weather radar control panel is available
c. The antenna is installed
78. MSU being is the ATT position, Heading of the aircraft is
a. Manually entered
b. Automatically detected
c. both
89. If the ON DC light is illuminated, what other indication(s) will the crew have that an IRS is
operating on DC power?
A. The Master Caution light, IRS annunciator and Crew call horn in the nose wheel well
B. The crew call horn in the nose wheel well sounds
C. The Master Caution light and OVERHEAD annunciator
90. What is the function of the SOURCE switch on the Navigation and Displays Panel?
A. Determine which IRS provides attitude and Heading information to the pilot instrument
B. Determine which EFIS control panels control’s the pilot’s display function
C. Determine which Display Electronic Unit (DEU) provides inputs for all display unit
91. ISDU, the function should only be used under which conditions?
A. Aircraft on the ground and during alignment
B. Aircraft on air and during alignment
C. Both A and B are correct
92. ISDU, When may manual entry of present position be accomplished?
A. When the ALIGN light is removed
B. When ALIGN light is illuminated
C. When ON DC is illuminated
93. On IRS Display Unit (ISDU) manual entry of Heading may be accomplished only when either
mode selector is in?
A. ATT (Attitude)
B. PPOS (present position)
C. Both A and B are answers
94.
95. When removing or installing the weather radar r/t, care should be taken to avoid damage to
__________
A. the captain static port air data module flexible hose.
B. the captain pitot air data module flexible hose.
C. the alternate static port air data module flexible hose.
A.
96. IRS SELECT SWITCH is located on _____________
97. weather radar/terrain (WXR/TERR) relays is controlled by ____________
A. ground proximity warning computer (GPWC) controls
B. TCAS
C. WXR R/T
98. and switches the relays
99. Which control panel enable you to select WXR/TERR futures?
100. Which control panel enable you to select weather radar range futures?
101. Which control panel enable you to select weather radar antenna TILT futures?
102. Weather radar control panel is located on ____________
103. Weather radar displayed on _____________
104. What message will be displayed for radio minimum data invalid? ______________
105. RA data NCD causes ______________
A. the RA display and rising runway symbol to be displayed on PFD
B. the RA display and rising runway symbol to be removed
C. the RA display and rising runway symbol to be displayed on ND
106. The rising runway is shown on _____________display
107. What are the conditions that make the rising runway to be shown in?
______________
_______________
108. What are the three procedures that sets the radio minimums alert back to normal?
109. How many RA antenna are installed on B737ng aircraft?
110. Which panel control Radio minimum value?
111. What is the frequency range of RA?
112. Why does painting the radiation surface or the back plate of the antenna is not
recommended?
113. What is the purpose of SYSTEM SELECT PROGRAM PIN of RA LRU?
114. Radio minimum is found on EFIS control panel
A. True
B. False
115. Radio Altimeter (RA) is displayed only on PFD
A. True
B. False
116. What is the maximum operating mach (MMO) for B737 Ng aircraft _____________?
117. The INOP light on the ground proximity warning module comes on for ____________
conditions:
A. TCAS inoperative
B. ILS inoperative
C. GPWS inoperative and Windshear inoperative
118. The GPWS WINDSHEAR warning annunciation shows for __________
A. a mode 7 condition
B. a mode 5 condition
C. a mode 1
119. The GPWS PULL UP warning annunciation shows for__________ conditions
A. mode 1, 2, 3 and 4 conditions
B. mode 1, 2, 3, 4 and 7 condition
C. mode 7 and mode 5 condition
120. RA displayed on _________
A. Only on PFD
B. PDF and ND
C. Only on ND
121. Where does the VMO/MMO Overspeed Warning, mach airspeed warning system gets
the overspeed
warning signal ?
A. IRS master caution unit
B. From an ADIRU
C. From Air Dara Module (ADM)
122. if your tasks ‘of today is removing or installing the weather radar r/t, you should
care to avoid damage to the _________________
a. captain pitot air data module flexible hose
123. weather radar control panel is on the ___________panel in the flight compartment.
a. P8 aft electronic
124. List all parameters that WXR R/T provide to DEUs to display:
Test
- Weather
125. What is the purpose of elevation and scan disable switches on WXR radar antenna
pedestals.
A. They remove power to the scan and elevation motors
126. the maximum allowable wind speed to open the nose radome is ____________
A. if wind speed is more than 15 knots
127. what is the the maximum and effective range of WXR R/T radiation on B737 ng aircraft?
A. shows weather displays out to a maximum range of 320 NM
128. If the weather/turbulence mode is selected while the range on EFIS control panel is set
on 320NM
A. ND shows weather data up to a maximum range of 40 nautical miles (NM) and turbulence data
beyond 40NM
B. NDs show weather and turbulence data up to a range of 40 NM and weather data only beyond
40 NM.
129. To avoid rf energy injuries to persons, make sure no persons are in the area of
_____________or less from the antenna when WXR R?T transmits rf energy.
A. 15 feet
130. WXR R/T the fault memory shows all the faults in the ______________legs in the R/T
memory. Fault memory shows these selections
A. 64 flight
131. Where is TOT is located?
A. Right side fuselage
B. Left side fuselage
C. Both on left and right side of the fuselage
132. What annunciator is displayed on MSU, when the IR function of the ADIRU fails.
A. FAULT, an amber annunciator
B. FAULT, a whit annunciator
C. ON DC, an amber annunciator
133. Which of the following statement is true about MSU mode selectors?
A. When the selector is in the NAV position, the operator must pull the knob to put it in the ATT
mode.
B. When the selector is in the ALIGN position, the operator must pull the knob to put the selector in
the OFF position. All other
C. Both
141. The green radio minimums display shows below the ADI display. The radio minimums
display does not show for what reasons?
A. Baro minimums is selected on the EFIS control panel and Radio minimums reset switch is
pushed
B. Radio minimums value is less than zero.
C. All are correct
145. When does the amber G/S flag replaces the glideslope deviation pointer and scale?
when the glideslope receiver function has a failure.
146. Which flight compartment control panel is used to do an ILS test?
A. EFIS
B. NAV
C. VHF Nav
147. What will be shown on PFD when marker beacon data fails or is no computed data
(NCD),
A. Amber MB flag
B. Red MB flag
C. display does not show.
148. The Weather radar WX/TURB mode displays detected turbulence within
A. 80Nm
B. 40NM
C. 320Nm
149. How many positions does have a VHF NAV switch on the navigation/displays source
select panel switch
A. three position
B. two position
150. What is the purpose the elevation and scan disable switches on antenna pedestal?
A. They remove power to the scan and elevation motors
B. They remove power from WXR radar R/T
C. They send antenna positions to the WXR R/T
151. From where you turn OFF WXR radar
152. Where does the WXR gets power?
153. Which control panel make the WXR radar on and OFF
A. WXR CP
B. EFIS CP
C. Both are correct
154. WXR receiver/transmitter (R/T) is found in
A. EE compartment
A. Forward equipment compartment
B. FORWARD BULKHEAD
155. When removing or installing the weather radar r/t, care should be taken to avoid
Damage to
A. when there is a LOC signal capture, and the radio altitude is below 2500 feet.
B. when there is a LOC signal capture, and the radio altitude is above 2500 feet.
C. when there is a GLIDESLOPE signal capture, and the radio altitude is below 2500 feet.
176. A displayed color of yellow on the radar indicates ___________ .
A. strong returns, areas of heaviest rainfall
B. intense to extreme turbulence
C. medium returns, moderate rainfall
177. When placing the IRS mode selector to ALIGN for initial alignment, the
aircraft must be ________.
() stationary
() on the ground
() straight and level
178. what will be displayed, when the localizer receiver function has a failure?
A. amber G/S flag replaces the glideslope deviation pointer
A. amber LOC flag replaces the localizer deviation pointer
B. Both A and B are correct answers.
179. What happened when the ILS data is invalid?
A. the scales and pointers are removed, Amber LOC and G/S fail flags are shown.
A. the localizer and glideslope deviation scales show but the pointers are removed
B. none
180. PDF shows FT
A. VOR/MB receiver 1 is on test
B. VOR/MB receiver 2 is on test
C. Both are correct
When the _______ light illuminates, the DC power for the respective IRS is not normal.
A. DC FAIL
B. FAULT
C. ALIGN
The B737-800 has how many independent GPS receiver(s)?
A. THREE
B. ONE
C. TWO
If you push the Identification (IDENT) switch the Transponder Panel ________________.
A. transmits an identification signal
B. turbulence
C. weather radar returns
If you push the WX switch on the weather radar, displays __________.
A. weather radar returns
B. strong returns
C. hail
The aircraft’s sole source of attitude and heading information are the ______ , except for the
standby attitude indicator and standby magnetic compass.
A. IRSs
B. GPSs
C. FMCs
The IRS has begun the alignment process when the ______ light extinguishes and the ______
light illuminates.
A. DC FAIL; FAULT
B. ON DC; ALIGN
C. ON DC; FAULT
Should either IRS fail, switch all associated systems to the functioning IRS by using the
_________.
A. IRS transfer switch
B. FMC
C. display control selector
Backup power to the _____ IRS is automatically terminated if ___ power is not restored within 5
minutes.
A. right; AC
B. right; DC
C. left; AC
Selecting the HDG/STS position of the IRS Display Unit displays true present heading in the left
window. The right window displays ____________.
A. time to next fix
B. fuel remaining in pounds X 1000
C. applicable maintenance status codes
The aircraft must be ________ when placing the IRS mode selector to ALIGN for initial
alignment.
A. stationary
B. on the ground
C. straight and level
After selecting the IRS mode selector to _________, the IRS provides full data to aircraft
systems for normal operations.
A. NAV
B. ALIGN
C. ATT
After selecting the IRS mode selector to _________, the IRS provides attitude and heading
only.
A. NAV
B. ALIGN
C. ATT
If an ALIGN Light on the Aft Overhead Panel flashes, it indicates that alignment cannot be
completed due to IRS detection of __________.
A. a significant difference between previous and entered positions or an unreasonable present
position entry
B. no present position being entered
C. all answers are correct
When the _______ light illuminates, a system fault affecting the related IRS ATT and/or NAV
modes has been detected.
A. DC FAIL
B. ALIGN
C. FAULT
When the _______ light illuminates, the DC power for the respective IRS is not normal.
A. DC FAIL
B. FAULT
C. ALIGN