Professional Documents
Culture Documents
YET845 Manuel
YET845 Manuel
YET845 Manuel
EN Version
Warnings
Dear customer, thank you for purchasing an Yaoertai(YET) product. This instruction sheet contains important information
about the usage modes and the safety of the installation. Fol ow the instructions and keep them for future reference.
Radio facilities can not be used in places that have influence factors (eg near police, airports, banks and hospitals).
It is important that a technician check before using the radio system. Radio instal ations may only be used if influences do not
create problems for the operation of the receiver and the transmitter.
If there is more than one installation in the same frequency field, both can be locked and not working properly.
Technical characteristics
Voltage: 230 V~ 50 Hz
Maximum power motors 500W
No mechanical motors 1
Temperature of exercise: -20°C ÷+ 70°C
Frequency radio 433,92 MHz
No max. Of command 80
Max. retardation 10 minutos
Measures 123 x 78 x 35mm
Observations
YET845 is an electronic control unit that allows the operation of motors with mechanical limit switches. It can directly feed
a photocell working at 12Vdc. External limit switches can be connected. Allows the connection of a courtesy light or warning lamp.
GND
L 230Vac Photocell input
N 230Vac +12V
Motor Common Climb limit switch
Motor up / down Limit switch
Motor down/up Lowering limit switch
Light
Programming
Insertion of transmitters.
A) Set UP key on the remote control: Press the programming button (LEARN) on the control unit once, the red LED light will light up.
Press the key of the command that we want to be the UP key, the LED will blink five times indicating that the process has been
performed correctly.
B) Set DOWN key on the remote control: Press the programming button (LEARN) on the control panel twice, the red LED light will
light up. Press the key of the command that we want to be the DOWN key. The LED flashes five times indicating that the process
has been performed correctly.
C) Set STOP key on the remote control: Press the programming button (LEARN) on the control unit three times, the red LED light
will be on.
Press the key of the command that we want to be the STOP key. The LED will blink five times indicating that the process has been
performed correctly.
D) Set LOCK / LIGHT key on the remote control: Press the programming button (LEARN) on the control panel four times, the red
LED light will be on. Press the key of the command that we want to be the LOCK / LIGHT key. The LED will flash five times
indicating that the process has been performed correctly.
Reset of transmitters.
A) Press and hold the 'LEARN' button until the red LED light turns off, then release the 'LEARN' button with this, the factory default
setting is reset (60 sec. Operating time and 30 sec).
Working time
Position the engine at the end of travel end.
Press the "TIME" time programming button on the receiver, the red led will light up. Press the RISE button on the controller until the
motor reaches the end of the run-up (the led will blink), then press the DOWN button on the controller until the motor reaches the
end of the run-down (the led will flash) . When the led goes off the working time is programmed.
Automatic close
Press the "TIME" time programming button on the receiver, the red led will light up.
Press the 3 key, the led will begin to flash and the automatic closing time will be stored. Press the 3 button on the remote
control when you want to end the automatic closing time
Function
4 Micro keys (Set microswitch 2 to ON)
The control unit will operate following the logic. Each command button performs an action.
Pressing the button defined as RISE on the transmitter, the control panel will perform a rise maneuver
By pressing the button defined as STOP on the transmitter, the control panel will execute a STOP command
By pressing the button set to DOWN on the transmitter, the control panel will carry out a lower order
1 Key (Set microswitch 2 to OFF)
The control unit will operate following the step-by-step logic. By pressing the button of the transmitter the control panel will perform a
rise maneuver, at the next press the motor will stop, at the next press the control will perform a maneuver of descent, etc.
LOCK / LIGHT Function