Professional Documents
Culture Documents
Iso 286-2-1988
Iso 286-2-1988
Iso 286-2-1988
Part 2:
Tables of standard toleranee grades and limit deviations
for holes and shafts
Reference number
ISO 286-2: \988 (El
Foreword
ISO Ithe International Organization tor Standardization) is a worldwide federation of
national standards bedies IISO member badies). The work of preparing International
Standards is normally carried out through ISO technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, gavern-
mental and non-governmental, in liaison with ISO, also take part in the werk.
This part ol ISO 286 has been prepared by ISO/TC 3, Limits and fits, and, together
with ISO 286-1, completes the revision ol ISO/R 286, ISO system of /imits and fits.
ISO/R 286 was lirst published in 1962 and subsequently conlirmed in November 1964;
it was based on ISA Bulletin 25 lirst published in 1940.
The major changes incorporated in this part of ISO 286 are as follows:
al The presentation of the information has been modified so that ISO 286 can be
used directly in both the design office and the workshop. This has been achieved by
•
separating the material dealing with the bases of the system, and the calculated
values of standard toleranees and fundamental"deviations, from the tables giving
specific limits of the most commonly used toleranees and deviations.
bi The new symbols js and JS replace the lormer symbols j, and J s Ii.e. s and S
are na longer placed as subscriptsl to facilitate the use of the symbols on equipment
with limited character sets, e.g. computer graphics. The letters "s" and "S" stand
for "symmetrical deviation".
cl Limit deviations have been included for basic sizes from 500 to 3 150 mm as
standard requirements (these were previously included on an experimental basis
onlyl.
dl Limit deviations have been extended for holes Hand JS, for shafts hand js, by
including tolerance grades IT17 and IT18 in all basic sizes, and, for experimental
purposes only, by including tolerance grades ITl to IT5 in basic sizes over 500 mm
up to 3 150 mmo
el Limit deviations have been extended for same tolerance classes used in fine
mechanisms and horology, in basic sizes up to 50 mmo
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
Printed in Switzerland
ii
ISO 286-2 : 1988 (E)
Contents Page
• 2
4
Field of application ................................................. .
jij
•
•
INTERNATIONAL STANDARD ISO 286-2: 1988 (E)
Part 2
Tables of standard toleranee grades and limit deviations
for holes and shafts
•
o Introduction ISO 286 covers values for the upper deviations ES (tor holes)
and es (tor shafts), and the lower deviations EI (for holes) and
The need for limits and fits tor machined workpieces was ei Ilor shafts} Isee ligure H.
brought about mainly by the inherent inaccuracy of manufac-
tu ring methods, coupled with the fact that "exactness" of size
was found to be unnecessary for most workpieces. In order NOTE - In the tables of limit deviations, the values for the upper
that function could be satisfied, it was found sufficient to deviation ES or es are shown above the values for the lower deviation
manufacture a given workpiece 50 that its size lay within two EI or eÎ except for toleranee class JS and js which is symmetrical about
the zero line.
permissible limits, i.e. a tolerance, th is being the variation in
size acceptable in manufacture .
With developments in industry and international trade, it The ISO system of limits and fits provides a system of toler-
became necessary to develop formal systems of limits and fits, ances and deviations suitable for plain workpieces.
firstly at the industrial level, then at the national level and later
at the international level. It should be noted that the general term "hole" or "shaft" used
in th is International Standard can be taken as referring to the
This International Standard therefore gives the internationally
space contained by (or containing) the two parallel faces (or
accepted system of limits and fits.
tangent planesl of any workpiece, such as the width of a slot or
the thickness ol a key Isee also ISO 286-1). Similarly, the term
A general graphical representation of the relationship between
"commonly used holes and shafts" shall be interpreted as pro-
the respective tolerance classes and their deviations is given in
the annex. viding a very wide choice of limit deviations suitable for a wide
variety of requirements.
1
ISO 286-2: 1988 (El
A toG
+ ES
EI ES K Zero line
EI
MtoZC
al Holes (internal features)
m to ze
+ el
es
Zero line
•
-'---'~ a to g
bi, Shafts (external features)
3 Reterences
NOTE - See also clause 7.
4 Standard toleranees
6 Limit deviations tor shatts
The values of standard tolerance grades ITl to 1T18 inclusive
are given in table 1. A synoptic representation of the tolerance classes for shafts,
given in this part of ISO 286, is shown in figures 4 and 5.
For information on the bases of the system and its application,
see ISO 286-1 ; for values of standard tolerances ITO and IT01, Attention is drawn to the fact that the tolerance classes shown
see ISO 286-1, annex A, table 5. in figures 4 and 5, and their limit deviations, given in tables 17
to 32, are not intended to give detailed directives on the selec-
tion of tolerance classes for any purpose. Recommendations
5 Limit deviations tor holes for the selection of toleranee classes are given in ISO 1829.
A synoptic representation of the tolerance classes for holes, NOTE - Some tolerance classes are only previded for a restricted
given in this part of ISO 286, is shown in figures 2 and 3. range of basic size steps. For further informatien, see note 1 on page 7.
2
ISO 286-2 : 1988 (E)
3
ISO 286-2 : 1988 (El
Tabla 1 - Numerical values of standard toleranee grades fT tor basic sizes up to 3 150 mm 11
.
NOTE - This tabie, taken trom ISO 286~ 1, has been included in this part of ISO 286 to facilitate understanding and use of the system .
2) Va lues for standard toleranee grades ITl to IT5 (incl.) for basic 5izes over 500 mm are included for experimental use.
•
3) Standard tolerance grades 1T14 to IT18 (inel.) shall not be used tor basic sizes less than or equal to 1 mmo
4
ISO 286-2: 1988 (El
Hl JSl
H2 JS2
EF3 F3 FG3 G3 H3 JS3 K3 M3 N3 P3 R3 53
EF4 F4 FG4 G4 H4 JS4 K4 M4 N4 P4 R4 S4
E5 EF5 FS FG5 G5 H5 JS5 K5 M5 N5 PS R5 55 15 U5 V5 X5
CDG DG E6 EF5 F6 FGB GB H6 JS6 J6 K6 MB NB PS RB 56 TB U6 V6 X6 Y6 ZB ZA6
CD1 07 E7 EF7 F7 FG7 G7 H7 JS7 J7 K7 M7 N7 P7 R7 57 nU7 V7X7 Y7 V ZA7 ZB7 ZC7
B8CB CDB DB EB EFB F6 FGB HB
GB JSS Je Ka MB NB PB RB SB TB UB VBX8 YB ZB ZA8 ZB8 ZCB
All B9 C9 CDB DB EB EFB F9 FGa Ga
H9 JS9 K9 M9 N9 P9 R9 59 U9 X8 Y9 ZB ZA!) ZB9 ZC9
AlO BlO Cl0 COlD 010 El0 EF10 Fl0 FG10 G10 Hl0 JS10 Kl0 MlO Nl0 PlO RlO SlO UlO Xl0 VlO ZlO ZA10 ZBlO zel0
All 811 e11 011 Hll JSll Nll Z11 ZAll ZB11 ZC11
Al2 812 C12 012 H12 JS12
A13 813 C13 013 H13 JS13
H14 JS14
H15 JS15
H16 JS16
H17 JS17
H1B JS18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 18
Tablas
• Figure 2 - Synoptic representation of toleranee classes for holes for basic Bizes less than or aqua I to 500 mm
Hl JSl
H2 JS2
H3 JS3
H4 JS4
H5 JS5
DG EB F6 GB H6 JS6 K6 M6 NB PS R6 S6 TB U6
07 E7 F7 G7 H7 JS7 K7 M7 N7 P7 R7 57 nU7
DB EB FB GB HB JSB KB MB NB PB RB S6 TB UB
DB EB FB H9 JS9 N9 P9
010 El0 HlO JS10
011 Hll JS11
012 H12 JS12
013 "'3 JS13
"'4 JS14
"'5 JS15
H16 JS16
• "17 JS17
"'B JSle
3 4 5 6 7 8 9 10 11 12 13
Tablas
NOTE - The tolerance classes in the frame are given for experimental use.
Figure 3 - Synoptic representatio" of toleranee classes for holes for basic sizes
greater than 500 mm and lass tha" or aqua I to 3 150 mm
5
ISO 286-2 : 1988 (E)
h' jsl
h2 j..:!
ef3
el'
13
"
193
194
g3
g4
h3
h4
js3
j'"
k3
k.
m3n3
m4n4
ol
p4
,. ..
,3 s3
'" ,,"
a9 b9 09 cdO dO e5 ef8 f9 199 g9 h9 jsS k9 m9n9 pB t6 sS u" ><9 y9 ,b9 ,09
alO blO cl0 cdl0 dl0 el0 eflO f10 fgl0 g'O h'O jslO klO plO ,'0 ,'0 )(10 ylO z10 zal0 zbl0 zcl0
all bll cll dll hll js11 kll z1' zal1 zbl1 ze11
a12 b12 c12 d,2 h'2 js12 kl2
a13 b13 d'3 h,3 js13 kl3
h" js14
h'5 js15
h,6 js16
h17 js17
h'B js18
17 18 19 20 21 22 23 24 2S 26 27 2B 29 30 31 32
Tables
Figure 4 - Synoptic representation of toleranee classes for shafts for basic sizes less thsn or aqual ta 500 mm
•
h' jsl
h2 j..:!
h3 js3
h4 j"
h5 js5
e5 f6 g6 h6 js5 k6 mB n6 pS rll s5 t6 u6
á1 e7 f7 g7 h7 js7 k7 m7 n7 p7 ,7 ,7 t7 u7
dB eB IB g6 hB jsB kB pB t6 sB uB
dO e5 f9 h" jsS kg
d'O e'O hlO jslO k'O
dll hll js11 kll
h,2 js12 k,2
h,3 js13 kl3
h'. js14
h,5 js15
h'6 js16
•
h,7 js17
h'B js18
18 19 20 21 22 23 24 25 26 27 2B 29
Tables
NOTE - The tolerance classes in the frame are given for experimental US8.
Figure 5 - Synoptic representation of toleranca classes for shafts for basic sizes
graatar than 500 mm and lass than or aqual to 3 150 mm
6
ISO 286-2 : 1988 (El
1 Values may ba calcutated. trom the bases given in ISO 286-1, for fundamental deviations used for toleranee classes.
for which there is no entry in the tablas. but for which the spa ce has been left blank.
2 A small horizontal separation has been inserted in the tablas. where appropriate. to distinguish batwBen values for
basic sizes lass than or aqual to 500 mm end those greater than 500 mm, which have been derived trom different bases .
7
ISO 286-2: 1988 (E)
- 3 21
+
+
295 + 310 + 330 + 370 + 410
270 + 270 + 270 + 270 + 270
+154
+140
+165
+140 : :: +
+
200 +
140 +
240 +
140 +
260
140
+ 74
+60
+85
+60
+100
+60
+120
+60
+
+
160 +
60 +
200
60
+ 300 + 31S + 346 + 390 + 450 +158 +170 + HI8 + 215 + 260 + 320 +88 +100 +118 +145 + 190 + 250
3 6
+ 270 + 270 + 270 + 270 + 270 +140 +140 + 140 + 140 + 140 + 140 +70 + 70 + 70 + 70 + 70 + 70
10
+ 31S + 338 + 370 + 430 + 500 +1n +188 + 20! + 240 + 300 + 370 +102 +116 HlS +170 + 230 + 300
6
+ 2BO +2BO + 260 + 2BO + 2BO +150 +150 + 150 + 150 + 150 + 150 +00 +00 + 80 +00 + 00 + 80
+ 333 + 360 + 400 + 470 + 560 +177 +193 + 220 + 260 + 330 + 420 +122 +138 +165 +205 + 275 + 365
10 18
+ 290 + 290 + 290 + 290 +290 +150 +150 + 150 + 150 + 150 + 150 + 95 +95 + 95 +95 + 95 + 95
:~~
+ 352 + 3B4 + 430 + 510 + 630 +193 + 244 + 290 + 370 +490 +143 +162 +1" +240 + 320 + 440.
18 30 + ,.
+ 300 + 300 + 300 + 300 + 300 +160 + 160 + 160 + 160 + 160 +"0 +1'0 +110 +110 + 110
30 40
+ 372 + 410
+ 310 + 310 I: ;;~ + 560 + 700
+ 310 + 310
+209
+170
+232
+170
+ 270 + 330 +420
+ 170 + 170 + 170 :: +159
+120
+192
+120
+220
+120
+2BO
+120
+ 370 +
+ 120 +
510
120
40 50 + 3B2 + 420 +
+ 320 +320 +
490 + 570 + 710
320 + 320 + 320
+219
+100
+242
+180
+ 2BO +
+ 100 +
340 +
180 +
430
180 : ;: +169
+130
+192
+130
+230
+130
+290
+130
+ 380 +
+ 130 +
520
130
50 65
+ 414 + 460 +
+ 340 + 340 +
530 + 640 +
340 + 340 +
000
340
+Zl6
+190
+264
+190
+ 310 +
+ 190 +
380 + 490
190 + 190 : :: +186
+140
+214
+140
+260
+140
+330
+140
+440 +
+ 140 +
600
140
65 80
+
+
434 + 490 +
360 + 360 +
560 + 860 +
360 +360 +
920
360
+246
+200 :: + 320 + 390 + 500 + 860
+ 200 + 200 + 200 +200
+196
+150
+224
+ 150 I~~~
+340
+150
+
+
450 +
150 +
S10
150
80 100
+467 + 520 +
+ 380 +380 +
600 + 73J +
380 + 380 +
920
380
+274
+220
+307
+220
+ 360 +440 + 570
+220 + 220 + 220 : :: +224
+170
+257
+ 170
+310
+170
+390
+170
+ 520
+ 170
+
+
710
170
+ 497 + 550 + 630 + 760 + 950 +294 +327 +380 + 460 + 590 + 700 +234 +257 +320 +400 + 530 + 720
100 120
+ 410 + 410 + 410 + 410 + 410 +240 +240 + 240 + 240 + 240 + 240 +100 +100 +100 +100 + 180 + 180
120 + 560 + 620 + 710 + 860 +1090 +323 +360 + 420 + 510 + 660 + 890 +253 +300 +360 +450 + 600 + 830
140
+ 460 + 460 + 460 + 460 + 460 +260 +260 + 260 + 260 + 260 + 260 +200 +200 +200 +200 + 200 + 200
140 160
+ 620 +600 +
+ 520 + 520 +
+600 + 740 + 830 +
770
520 1_:
920 +1150
520 + 520
980 +1210
+343
+2BO
+373
::
+410
+ 440 +
+ 2BO +
530 + 600 + 910
2BO + 2BO +260
+ 470 + 560 + 710 +940
+273
+210
+293
+310
+210
+330
~~~
+390
+460
+210
+490
+ 610 +
+ 210 +
+ 630 +
840
210
860
160 180
+ 500 + 500 + 5BO + 500 + 500 +310 +310 + 310 + 310 + 310 + 310 +230 +230 +230 +230 + 230 + 230
+775 +845 + 950 +1120 +1380 +412 +455 + 525 + 630 + 000 +1060 +312 +355 +425 +530 + 700 + 960
180 200
+ 660 + 660 + 860 + 660 + 860 +340 +340 + 340 + 340 + 340 + 340 +240 +240 +240 +240 + 240 + 240
:~
+ 855 + 925 +1030 +1200 +1460 +452 +495 +565 + 670 + 840 +1100 +332 +375 +445 +550 +720
200 225
+ 740 + 740 + 740 + 740 + 740 +380 +380 + 380 + 380 + 380 + 380 +260 +260 +260 +260 + 260
I:~:
+ 935 +1 110 +1200 +1540 +492 +535 + 605 + 710 +600 +1140 +352 +395 +465 +570 + 740 +1000
225 250
+ 920 + 920 1+ 920 +~ +420 +420 + 420 + 420 + 420 + 420 +2BO +2BO +2BO +2BO + 2BO + 2BO
+1060 +1130 +1240 +1440 +1730 +561 +610 + 690 + 000 +1000 +1290 +381 +430 +510 +620 + 920 +1110
250 280
+920 +920 + 920 + 920 + 920 +490 +490 +490 + 490 +480 + 490 +300 +300 +300 +300 + 300 + 300
280 315
+1180
+1060 I::: +1370 +1570
+1060 +1050 I::: +621
+540
+670
+540 :: + 860 +1060 +1350
+ 540 + 540 + 540
+411
+330
+460
+330
+540
+330
+650
+330
+ 850 +1 140
+ 330 + 330
:~:
+ 830 + 960 +1170 +1490
~:
+1340 +1430 +1560 1+ 1770 +689 +740 +449 +500 +720 +930 +1250
315 355
+1200 +1200 +1200 1 +1 200 +000 +600 + 600 + 600 + 600 + 600 +360 +360 +360 + 360 + 360
I:~:
+1710 +1920 + 910 +1040 +1250 +1570
~~;
+1490 +769 +920 +489 +540 +630 +760 + 970 +1290
355 400
+1350 +1350 +1350 +600 +600 + 600 + 600 +600 + 600 +400 +400 +400 +400 +400 + 400
+1656 +1750 +1900 +2130 +2470 +857 +915 +1010 +1160 +1390 +1730 +537 +595 +690 +840 +1070 +1410
400 450
+1500 +1500 +1500 +1500 +1500 +760 +760 + 760 + 760 + 760 + 760 +440 +440 +440 +440 + 440 + 440
450 500
+1805 +1900 +2050
+1650 +1650 +1650 I:~: :~: +937
+840
+995
+840
+1090 +1240
+ 840 + 840 1: ': +1810
+ 840
+577
+490
+535
+480
+730
+490
+800
+490
+1110 +1450
+ 490 + 490
1) Fundamental deviations A, 8 end C are not provided for basic sizes greater than 500 mmo
2) Fundamental deviations A and B shall not be used for any standard toleranee in basic sizes lass than or equa! to 1 mmo
8
ISO 286-2: 1988 (E)
Basic slza 0
CD" E
mm
Up to
Above and in- 6 7 8 9 10 6 7 8 9 10 11 12 13 5 6 7 8 9 10
cluding
"
3 6 +54
+48 I:: +64 +15
+48 +48
+94
+48
+ 38
+30
+42
+30
+48
+30
+
+
6(} +
30 +
15 +
30 +
106 +
30 +
150
·30 : 2:
+25
+20
+28
+20
+32
+20
+38
+20
+50
+20
+
+
68
20
I:~ I: ~
+66 +15 +92 +114 +49 +55 +62 + 15 + 98 + 130 + 190 + 31 + 34 +40 + 61 + 83
6 10 + "
+56 +56 +56 +56 +40 +40 +40 + 40 + 40 + 40 + 40 +25 + 25 +25 +25 +25 + 25
10 18
+ 61
+ 50
+68
+ 50
+17
+50
+
+
93 +
50 +
IlO +
50 +
16(} + 230
50 + 50 I: ~ +40
+ 32
+43
+ 32
+50
+32
+ 61
+ 59
+32
+15
+32
+
+
lOl
32
+18 +86 +98 + 111 + 149 + 195 + 215 + 395 + 49 + 53 +13 +92 + 12'
18 30
+66 +66 +65 + 66 + 65 + 66 + 65 + 66 + 40 + 40 +40 +40 + 40 + 40
+96 +106 +119 + "2 + 180 + 240 + 330+ "0 + 61 + 66 + 15 +89 + 112 + 150
30 50
+80 + 80 +80 + 80 + 80 + 80 + 80 + 80 +50 + 50 +50 +50 +50 + 50
+119 +130 +148 + 1,. + 220 + 280 + 400+ 560 + 13 +79 + ,., +106 +134 + 180
50 SO + 6(} +6(} +6(} +6(} + 6(}
+100 +100 +100 + 100 + 100 + 100 + 100 + 100 +60
SO IlO +142
+120
+155
+120
+174
+120
+ 'l!JI + 260 + 340 + "0
+ IlO + IlO + IlO + 120 :: +81
+n
+94
+n
+101
+n
+125
+n
+159
+n I: 2~
120 ISO + 170
+145
+185
+145
+2(11
+145
+ 245 +
+ 145 +
305 + 395 + 545
145 + 145 + 145 :: +103
+85
+110
+85
+125
+85
+148
+ 85
+185
+85 I: ~
+1" +216 +242 + 285 + 355 + 460 + 630 + 800 +120 +129 +146 +1n +215 + 285
ISO 250
+170 +170 +170 + 110 + 110 + 110 + IlO + 110 +100 +100 +100 +100 +100 + 100
+222 +242 +211 + 320 + 400 + 510 + 110 +1000 +133 +142 +162 +191 +240 + 320
250 315
+ I,., + I,.,
+ I,.,
+246
+1,.,
+261
+190
+298
+ 190 + +
'''' ''''
+ 350 + 440 + 510 + 180 +1100
+'10
+150
+110
+161
+110
+182
+110
+214
+110
+266
+ 110
+ 355
315 400
+210 +210 +210 + 210 + 210 + 210 + 210 + 210 +125 +125 +125 +125 +125 + 125
+210 +293 +327 + 385 + 480 + 630 + 860 +1200 +162 +175 +198 +232 +280 + 385
400 500
+230 +230 +230 + 230 + 230 + 230 + 230 + 230 +135 +135 +135 +135 +135 + 135
+304 +330 +310 + 435 + 540 + 100 + 960 +1360 +189 +215 +255 +320 + 425
500 630
+260 +260 +260 +260 + 260 + 260 + 260 + 260 +145 +145 +145 +145 + 145
+340 +370 +415 +480 + 610 + 790 +1090 +1540 +210 +240 +285 +360 + 480
630 800
+280 +290 +290 + 290 + 280 + 280 + 280 + 290 +16(} +16(} +160 +16(} + 160
+316 +410 +460 + 550 + 680 + 880 +1220 +1720 +226 +260 +310 +400 + 530
800 1000
+320 +320 +320 + 320 + 320 + 320 + 320 + 320 +170 +170 +170 +170 + 110
1000 1250 +416 +455 +515 + 610 + 170 +1010 +1400 +2000 +261 +300 +360 +455 + 615
+350 +350 +350 + 350 + 350 + 350 + 350 + 350 +195 +195 +195 +195 + 195
+468 +515 +585 + 100 + 800 +1170 +1540 +2340 +298 +345 +415 +530 + na
1250 1600
+390 +390 +390 +390 + 390 + 390 + 390 + 390 +220 +220 +220 +220 + 220
+522 +580 +660 + 800 +1030 +1350 +1930 +2130 +332 +390 +470 +610 + 840
1600 2000
+430 +430 +430 + 430 +430 + 430 + 430 + 430 +240 +240 +240 +240 + 240
9
ISO 286-2 : 1988 (E)
Basic size
EFlI F
mm
Up to
Above and jn- 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
cluding
+12 +13 +14 +16 +20 +24 +35 +50 + 8 + 9 +10 + 12 + 16 +20 + 31 + 46
- 3
+10 +10 +10 +10 + 10 +10 +10 +10 + 6 + 6 + 6 + 6 + 6
+ 6 + 6 + 6
+16,5 +18 +19 +22 +26 +32 +44 +62 +12,5 +14 +15 + 18 +22 +28 +40 + 56
3 6
+14 +14 +14 +14 +14 +14 +14 + 14 +10 +10 +10 + 10 + 10 + 10 + 10 + 10
6 10 +20,5 +22 +24 +TI +33 +40 +54 +76 +15,5 +17 +19 +22 +28 +35 + 49 + 71
+ ~8 +18 + 18 +18 +18 +18 +18 +18 +13 +13 +13 + 13 + 13 + 13 + 13 + 13
•
+16 +16 + 16 + 16 + 16 + 16 + 16 + 16
500
630
BOD
630
BOO
1000
+120
+ 76
+130
+80
+142
+ 86
+146
+ 76
+160
+ 80
+176
+86
+186
+ 76
+205
+80
+226
+86
+251
+ 76
+280
+80
+316
+86
•
1 ()()() +164 +203 +263 +356
1250
+98 + 98 +98 +98
+188 +235 +305 +420
1250 1600
+110 +110 +110 +110
1) The intermediate fundamental deviatien EF is provided primarily for fine mechanisms and horology. 11 tolerance classes involving this fundamental
deviatien in other basic sizes are required, they may be calculated in accordance with ISO 286-1.
10
ISO 286-2 1988 (EI
Basic size
FG" G
mm
Up to
Above and in· 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
cluding
+ 6 + 7 + 8 +'0 + '4 +'8 +29 +44 + 4 + 5 + 6 + 8 + '2 + '6 + 27 + 42
- 3
+ 4 + 4 + 4 + 4 + 4 + 4 + 4 + 4 + 2 + 2 + 2 + 2 + 2 + 2 + 2 + 2
+ 8,5 +'0 +', +'4 +'8 +24 +36 +54 + 6.5 + 8 + 9 + '2 + '6 +22 +34 + 52
3 6
+ 6 + 6 + 6 + 6 + 6 + 6 + 6 + 6 + 4 "- 4 + 4 + 4 + 4 + 4 + 4 + 4
+10,5 +'2 +'4 +17 +23 +30 +44 +66 + 7,5 + 9 +', + '4 +20 + 27 + 4' + 63
6 '0 + 8 + 8 + 8 + 8 + 8 + 8 + 8 + 8 + 5 + 5 + 5 + 5 + 5 + 5 + 5 + 5
+ 9 +11 +'4 + 17 + 24 +33 + 49 + 76
18
•
'0 + 6 + 6 + 6 + 6
+ 6 + 6 + 6 + 6
+11 +13 +'6 +20 +28 + 40 + 59 + 9'
18 30
+ 7 + 7 + 7 + 7 + 7 + 7 + 7 + 7
• 500
630
800
630
800
1000
+ 66
+ 22
+ 74
+ 24
+ 82
+ 92
+ 22
+'04
+ 24
+116
+'32
+ 22
+'49
+ 24
+'66
+ 26 + 26 +26
Basic siza H
mm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 1511 1611 17 11 1811
'
Up to Deviations
Above and in-
cluding ~m mm
- 311 +0,8 + I ~.l + 2 + 3 + 4 + 6 + 10 + 14 + 25 +40 + 60 +0,1 +0,14 +0,25 +0,4 + 0,6
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
3 6
+1
0
I + ~" + ~,5 + 4
0
+ 5
0
+ 8
0
+ 12
0
+ 18
0
+ 30
0
+ 48
0
+ 75
0
+0,12
0
+0,18
0
+0,3
0
+0,48
0
+ 0,75
0
+ 1,2
0
+ 1.8
0
6 10
+1
0
I+ ~" + ~,5 + 4
0
+ 6
0
+ 9
0
+ 15
0
+ 22
0
+36
0
+58
0
+ 90
0
+0,15
0
+0,22
0
+0,36
0
+0,58
0
+ 0,9
0
+ 1,5
0
+ 2.2
0
+1.2 + 2 + 3 + 5 + 8 + 11 + 18 + 'EI +43 + 70 + 110 +0.18 +0,27 +0.43 +0.7 + 1.1 + 1.B + 2,7
10 18
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
18 30 I +~,5 1+ 2,' + 4 + 6 + 9 + 13 + 21 +33 +52 +84 + 130 +0,21 +0,33 +0,52 +0,84 + 1,3 + 2.1
~'~
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+1,5 1+ 2,5 + 4 + 7 +11 + 16 + 25 +39 + 62 +100 + 160 +0,25 +0.39 +0,62 +1 + 1,6 + 2,5
30 50 + 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
50 BO +2
0
I+ ~ + 5
0
+ 8
0
+13
0
+ 19
0
+30
0
+46
0
+ 74
0
+120
0
+ 190
0
+0,3
0
+0.46
0
+0,74
0
+1,2
0
+ 1,9
0
+ 3
0
+ 4.6
0
+2.5 + 4 + 6 +10 +15 +22 + 35 +54 +87 +140 +220 +0,35 +0,54 +0,87 + 1,4 + 2,2 + 3,5 + 5,4
BO 120
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+3,5 + 5 + 8 +12 +18 +25 + 40 +63 +100 +160 + 250 +0,4 +0,63 +1 +1,6 + 2.5 + 4 + 6,3
120 lBO
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+4,5 + 7 +10 +14 +20 + 29 +46 +72 +115 +185 + 290 +0,46 +0.72 +1,15 +1,85 + 2,9 + 4,6 + 7.2
180 250
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+6 + 8 +12 +16 +23 +32 +52 + 81 +130 +210 +320 +0.52 +0,81 +1.3 +2,1 + 3,2 + 5,2 + 8.1
250 315
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+7 +13 +18 +25 +36 +57 +89 + 140 +230 + 360 +0,57 +0,89 +2.3 + 3,6 + 5,7 + 8,9
315 400 1+ 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+8 +10 +15 +20 + 'EI +40 +63 + 97 +155 +250 + 400 +0,63 +0,97 +1,55 +2.5 + 4 + 6,3 + 9,7
400 500
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
21
500 630 + 9 +11 +16 +22 +32 +44 + 70 +110 + 175 +280 +440 +0,7 +1,1 + 1,75 +2,8 + 4.4 + 7 +11
0 0 ·0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
~
+10 +13 +18 +25 +36 +50 + 80 +125 +200 +320 + 500 +0,8 +1.25 +2 +3,2 + 5 + 8
630 BOO
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BOO 1000
+11 +15 +21 +28 +40 + 56 +90 +140 +230 +360 + 560 +0,9 + 1,4 +2,3 +3,6 + 5,6 + 9 +14
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 ()()() +13 +18 +24 +33 +47 +66 +105 +166 +260 +420 + 660 +1,05 +1,65 +2,6 +4.2 + 6.6 +10,5 +16.5
1250
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+15 +2~ +29 +39 +55 +78 +125 +195 +310 +500 +780 +1,25 +1.95 +3,1 +5 + 7,8 +12,5 +19.5
1250 1600
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1600 2 ()()() +18 +25 +35 +46 +65 +92 +150 +230 +370 +600 + 920 +1,5 +2,3 +3,7 +6 + 9.2 +15 +23
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 ()()() 2500
+22 +30 +41 +55 +78 + '10 +175 +280 +440 +700 +1100 +1.75 +2,8 +4,4 +7 +11 +17,5 +28
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2500 +28 +36 +50 +58 +96 +135 +210 +330 +540 +860 +1350 +2.1 +3,3 +5,4 +8,6 +13,5 +21 +33
3150
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1) Tolerance grades IT14 to IT18 !lncl.) shall not be used for baSIC Sizes less than or equal to 1 mmo
2) The values given in the frame, for toleranee grades ITl to IT5 (incl. I, tor basic sizes greater than 500 mm and less than or equa! to 3 150 mm, are included
for experimental use.
12
• Tabla 7 - Limit deviations 1) for holes JS
Upper limit deviation = ES
•
Lower limit deviation = El
Basic size JS
mm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 21 15 21 16 21 17 18
Up to
Deviations
Above and in-
cluding ~m mm
- 3 21 iDA iO,S i 1 ± 1,5 i 2 i 3 i 5 ± 7 ± 12,5 ±20 ±30 ia,05 ±D,07 ±O,l25 ±O,2 ±O,3
3 6 ia,S ±O,75 ±1,25 i 2 ± 2,5 ± • ± 6 i 9 ± 15 ± 2. ± 37,5 ia,06 ±O,09 ±O,1S i 0,24 ±O,375 ± 0,6 ± 0,9
6 10 ±a,s ±O,75 ±1,25 ± 2 ± 3 ± 4,5 i 7,5 i 11 i 18 i29 i45 ±O,015 ±O,1l ia,lB ±O.29 ±O,45 ± 0,75 ± 1,1
10 18 iO,G ±1 ± 1,5 ± 2.5 ± 4 ± 5,5 ± 9 ± 13,5 ± 21,5 ±35 i 55 ±O,09 ±O,l35 ia.2tS ±O,35 ia.55 ± 0,9 ± 1.35
18 30 ±O,75 ±1,25 i2 i 3 ± 4,5 ± 6,5 ± 10,5 ± 16,5 ±26 ±42 ±65 ±a,tIE ±O,l65 ±O.26 ±O.42 ia,65 ± 1,05 ± 1,65
30 50 ±O,75 ±1,25 i2 ± 3,5 ± 5,5 ± 8 ± 12,5 ± 19,5 ± 31 ±50 ±SO ±O,l25 ±O,l95 iO,31 iO,S ±O,S ± 1,25 ± 1,95
50 BO ±1 ±l,S ±2.S ± • ± 6,5 ± 9.5 i 15 i23 i 37 ±OO ±95 ±O,15 i 0,23 ±O.37 iO,G ±O.95 ± 1,5 ± 2.3
BO 120 ±1,25 ±2 ±3 ± 5 ± 7.5 ±11 ± 17,5 ± 27 . ± 43,5 ±70 ±11O ±O,175 ±O.27 ±O,435 iO,7 il.1 ± 1.75 ± 2,7
120 lBO ±1,75 ±2,S ±. ± 6 ± 9 ±12,5 ±20 ± 31,5 ±50 ±SO i 125 ±0,2 iO,3l5 ±0,5 ±0,8 ±1,25 ± 2 ± 3,15
lBO 250 ±2,25 i3,5 ±5 i 7 ±1O i14,5 ±23 ±36 ± 57,5 ± 92,5 ±145 ±0,23 ±0,36 i 0,575 i 0,925 i1,45 i 2,3 ± 3,6
250 315 i3 i' ±6 ± 8 i 11,5 ±16 ±26 ± 40,5 ±65 ±105 il00 ±0,26 ±0,400 ±0,65 il,OS il,6 ± 2,6 i 4,05
315 400 ±3,5 ±4,5 ±6,S ± 9 ±12,5 ± 18 ± 28,5 ± 44,5 ± 70 ± 115 ±180 i 0,285 ±0,445 ±0,7 ±1,15 ±1,8 ± 2,85 ± 4,45
400 500 ±4 ±5 ±7,5 ilO i13,5 ±20 ± 31,5 i 48,5 ± n,S ±125 ±200 iO,3l5 ±0,485 ±0,n5 ±1,25 ±2 i 3,15 i 4,85
31
500 630 i 4,5 ± 5,5 ± 8 ±11 i16 ±22 ±35 ±55 ± 87,5 ±14O ±22O i 0,35 i 0,55 i 0,875 ±l,4 i2,2 i 3,5 ± 5,5
630 BOD ± 5 i 6,5 ± 9 i12,5 ±18 ±25 i40 i 62,5 i 100 il00 i 250 ±0,4 ±O,625 ±, ±l,6 ±2,5 ± • ± 6,25
BOD 1000 i 5,5 i 7,5 ±10,5 ±1' ±20 i26 ±45 ± 70 ±115 . ±180 i 260 ±O,45 ±O,7 i 1.15 ±1,8 t2,8 t 4,5 ± 7
1000 1250 i 6,5 ± 9 ±12 t16,5 ±23,5 i33 i 52,5 ± 82,5 ±130 ±210 ±33O ±O,525 ±O,825 il,3 i2,l ±3,3 t 5,25 ± 8,25
1250 1 BOD i 7,5 ±10,5 ±14,5 i 19,5 t27,5 ±39 ± 62,5 ± 97,5 ±155 ±250 ±390 ±O,625 ±0,975 ±1,55 t2,5 ±3,9 ± 6,25 t 9,75
1600 2000 ± 9 i12,5 ±17,5 ±23 ±32,S ±46 ±75 ± 115 ±185 ±3OO ±400 tO,75 ±l,15 ±l,85 ±3 i4,6 i 7,5 ±ll,S
2000 2500 ±11 i15 ±lO,S ±27,S ±39 ±55 i 87,5 ±14O ±220 ±350 i 550 ±0,875 i 1,4 ±2,2 i3,S iS,5 ± 8,75 ±1'
2500 3150 ±13 ±18 ±25 ±34 ±4B ±67,5 ±105 ± 165 ±270 ±43O ±675 tl,OS tl,65 i2,7 ±4,3 t6,75 ±lO,5 ±16,5
1) In order to avoid repetition of equal values, the table tists the values as "±x"; thls is to be interpreted as ES + x and EI - x, e.g. +0,23 jlm.
-0,23
(ij
2) Toleranee grades IT14 to IT16 (jncl.) shaJJ not be used for basic sizes less than or aqual to 1 mmo
o
3) The values in the frame, for tolerance grades IT1 to lTS (incl. J, for basic sizes greater than 500 mm and less than or aqual to 3 150 mm, are included for experimental use.
~
...
11
...
W !!!
ISO 286-2 1988 IE)
Basic size
J K
mm
Up to
Above and in- 6 7 8 9" 3 4 5 6 7 8 9 21 10 21
.
cluding
3
3
6
+ 2
-
+ 5
+ •
- 6
± s31
+ 6
- 8
+10
0
-2
0
0
-3
+0.5
-
0
. 0
-
+
0
6
2
0
- 10
+ 3
-
+ 5
0
"
0
-25
0
-40
.
- 3 - 8 -2,5 -3,5 - 5 - 6 - 9 - 13
+ 5 + 8 +12 0 +0,5 + 1 + 2 + 5 + 6
6 10
- - 7 -10 -2,5 -3,5 - 5 - 7 - 10 - 16
-.
•
10 18 + 6 +10 +15 0 +1 + 2 + 2 + 6 + 8
- 5 - 8 -12 -3 - 6 - 9 - 12 - 19
+ 8 +12 +20 -0,5 0 + 1 + 2 + 6 + 10
18 30
- 5 - 9 -13 -4,5 -6 - 8 - 11 - 15 - 23
+10 +1' +2' -0,5 +1 + 2 + 3 + 7 + 12
30 50
- 6 -11 -15 -4,5 -6 - 9 - 13 - 18 -27
50 80
+13
- 6
+18
-12
+28
-18
+ 3
-10
+
- 15
• + 9
- 21
+ "
- 32
80 120
+16
- 6
+22
-13
+34
-20
+ 2
-13
+
- 18
• + 10
-25
+ 16
- 38
120 180
+18
- 7
+26
-I'
+41
-22
+ 3
-15
+
- 21
• + 12
-28
+20
-43
+22 +30 +47 + 2 + 5 + 13 + 22
180 250
- 7 -16 -25 -18 - 24 -33 -50
500
630
630
800
1000
0
-44
0
-50
0
-80
0
0
- 70
0
0
-110
0
-125
0
•
800
- 56 -80 -140
0 0 0
1000 1250
-66 -105 -165
0 0 0
1250 1800
-78 -125 -195
0 0 0
1800 2000
-92 -150 -230
0 0 0
2000 2500
-110 -175 -280
0 0 0
2500 3150
-135 -210 -330
1) Tolerance classes J9, J10, etc. are symmetrical about the zero hne. For these values, see JS9, JS10, etc.
2) Deviations for K in tolerance grades above lTS are not defined for basic sizes greater than 3 mmo
14
ISO 286-2: 1988 (El
Basic Biza
M N
mm
Up to
Above and in- 3 4 5 6 7 8 9 10 3 4 5 6 7 8 911 tO 11 11 11
cluding
- 3 '1
- 2 - 2 - 2 - 2 - 2 - 2 - 2 - 2 - 4 - 4 - 4 - 4 - 4 - 4 - 4 - 4 - 4
- 4 - 5 - 6 - 8 - 12 - 16 -27 - 42 - 6 - 7 - 8 - 10 - 14 - 18 -29 - 44 -64
- 3 - 2,5 - 3 - 1 0 + 2 - 4 - 4 - 7 - 6,5 - 7 - 5 - 4 - 2 0 0 0
3 6
- 5,5 - 6.5 - 8 - 9 - 12 - 16 -34 - 52 - 9,5 -10,5 -12 - 13 - 16 - 20 -30 - 48 - 75
6 10
- 5 - 4,5 - 4 - 3 0 + 1 - 6 - 6 - 9 - 8,5 - 8 - 7 - 4 - 3 0 0 0
- 7,5 - B,5 -10 - 12 - 15 - 21 -42 - 64 -11,5 -12,5 -14 - 16 - 19 - 25 - 35 -58 -90
- 6 - 5 - 4 - 4 0 + 2 - 7 - 7 -11 -10 - 9 - 9 - 5 - 3 0 0 0
•
10 18
- 9 -10 -12 - 15 - 18 -25 -50 - n -14 -15 -17 - 20 - 23 - 30 - 43 - 70 -110
18 30
- 6,5 - 6 - 5 - 4 0 + 4 - 8 - 8 -13,5 -13 -12 - 11 - 7 - 3 0 0 0
-10,5 -12 -14 - 17 - 21 -29 -60 - 92 -17,5 -19 -21 - 24 -28 - 35 - 52 -84 -130
30 50
- 7,5 - 6 - 5 - 4 0 + 5 - 9 - 9 -15,5 -14 -13 - 12 - 8 - 3 0 0 0
-11,5 -13 -16 -20 - 25 -34 -71 -109 -19,5 -21 -24 - 28 -33 - 42 -62 -100 -160
50 80
- 6 - 5 0 + 5 -15 - 14 - 9 - 4 0 0 0
-19 - 24 - 30 - 41 -28 - 33 -39 - 50 - 74 -120 -190
- 8 - 6 0 + 6 -18 - 16 - 10 - 4 0 0 0
80 120
-23 - 28 - 35 -48 -33 - 38 -45 - 58 - 87 -140 -220
• 500
630
800
630
800
1 (]()()
-26
- 70
-30
- 80
-34
-26
-
-
-110
- 34
96
30
-26
-135
-30
-155
-34
- 44
- 88
-50
-100
-56
-44
-114
- 50
-130
-56
-44
-164
- 50
-175
- 55
- 44
-219
- 50
-250
- 56
-90 -124 -174 -112 -146 -196 -286
1 (]()() 1250
-40 - 40 -40 -66 -66 -66 -66
-106 -145 -205 -132 -171 -231 -326
-48 - 48 -48 -78 -78 -78 - 78
1250 1600
-126 -173 -243 -156 -203 -273 -388
2 (]()() 2500
- 66 - 68 - 68 -110 -110 -110 -110
-178 -243 -348 -220 -286 -390 -550
- 76 - 76 - 76 -135 -135 -135 -135
2500 3150
-211 -286 -406 -270 -345 -465 -675
1) Tolerance classes N9, Nl0 and Nl1 shall not ba used for baSIC SIZes less than or equal to 1 mmo
ISO 286-2: 1988 IE)
Basic size p
mm
Up to
Above and in- 3 4 5 6 7 8 9 10
cluding
- 3
- 6 - 6 - 6 - 6 - 6 - 6 - 6 - 6
- 8 - 9 -10 - 12 - 16 -20 - 31 -46
3 6
-11 -10,5 -11 - 9 - 8 - 12 - 12 - 12
-13,5 -14,5 -16 - 17 -20 -30 -42 -60
6 10
-14 -13,5 -13 - 12 - 9 - 15 - 15 - 15
-16,5 -17,5 -19 - 21 - 24 -37 - 51 -73
-17 -16 -15 - 15 - 11 - 18 - 18 - 18
•
10 18
-20 -21 -23 -26 -29 -45 - 61 -88
80 120
-32 -30 - 24 -37 -37
-47 - 52 - 59 - 91 -124
-37 -36 -28 -43 -43
120 180
-55 - 61 -68 -106 -143
180 250
-44 - 41 -33 -50 -50
-64 - 70 -79 -122 -165
-49 - 47 -36 - 56 - 56
250 315
-n - 79 - 88 -137 -186
-55 - 51 - 41 -62 -62
315 400
-80 - 87 -98 -151 -202
-61 -55 -45 -68 - 68
400 500
-88 - 95 -100 -165 -223
500
630
800
630
800
1000
-78
-122
-88
-138
-100
- 78
-148
-88
-168
-100
-78
-188
-88
-213
-100
-78
-253
-88
-288
-100
•
-156 -190 -240 -330
-120 -120 -120 -120
1000 1250
-186 -225 -285 -380
-140 -140 -140 -140
1250 1600
-218 -265 -335 -450
-170 -170 -170 -170
1600 2000
-262 -320 -400 -540
-195 -195 -195 -195
2000 2500
-305 -370 -475 -635
-240 -240 -240 -240
2500 3150
-375 -450 -570 -780
16
ISO 286-2: 1988 (EI
- 3
-10 -10 - 10 - 10 - 10 - 10 -10 - 10
500 560
-150 -150 -150
-12 -13 - 14 - 16 -20 - 24 -35 -50 -194 -220 -280
3 6
-14 -13,5 - 14 - 12 - 11 - 15 -15 - 15
560 630
-155 -155 -155
-16.5 -17,5 - 19 -20 -23 -33 -45 -63 -199 -225 -285
•
-25 -26 -28 - 31 - 34 -50 -66 -93 -235 -265 -310
-26,5 -26 - 25 - 24 -20 -28 -28 - 10 -210 -210 -210
18 30 800 900
-30,5 -32 -34 -'fl - 41 - 61 -80 -112 -288 -300 -350
-32.5 -31 - 30 -29 -25 -34 -34 -34 -220 -220 -220
30 50 900 1000
-36.5 -38 - 41 - 45 -50 -73 -96 -134 -278 -310 -360
- 36 -35 -30 - 41 -250 -250 -250
50 65 1000 1 120
-49 -54 -00 -f51 -316 -355 -415
- 36 -'fl -32 -43 -280 -280 -280
65 80 1 120 1250
- 51 -56 -62 -89 -326 -365 -425
-46 -44 -38 - 51 -300 -300 -300
80 100 1250 1400
- 61 -66 -73 -105 -378 -425 -495
•
180 200 2240 2500
- 91 - 97 -106 -149 -570 -635 -740
- 74 - 71 -63 -80 -660 -550 -660
200 225 2500 2600
-94 -100 -109 -152 -685 -700 -880
17
ISO 286-2: 1988 (E)
-27 -26 -25 -25 - 21 -28 -28 -28 - 3BO - 3BO - 3BO
•
10 18 710 800
-30 -31 - 33 -36 -39 -55 - 71 -98 - 430 - 4BO - 505
65
- 48 - 47 - 42 -53 - 53
1000 1 120
- 520 - 520 - 520
50
- 61 -66 -72 -99 -127 - 5B6 - 625 - 685
- 64 -53 - 48 -59 -59 - 5BO - 5BO - 5BO
65 80 1 120 1250
-67 -72 - 78 -105 -133 - 64B - 685 - 745
100
- 68 - 64 - 58 - 71 - 71
1250 1400
- 640 - 640 - 640
80
- BI -86 - 93 -125 -158 - 71B - 766 - 835
140
-86 -85 -77 -92 - 92
1800 1800
- 820 - 820 - 820
120
-104 -110 -117 -155 -192 - 912 - 970 -1050
-94 -93 -85 -100 -100 - 920 - 920 - 920
140 180 1800 2000
-112 -118 -125 -163 -200 -1012 -1070 -1150
•
-116 -113 -105 -122 -122 -1100 -1100 -1100
180 200 2240 2500
-136 -142 -151 -194 -237 -1210 -1275 -13BO
-124 -121 -113 -130 -130 -1250 -1250 -1250
200 225 2500 2800
-144 -150 -159 -202 -245 -13B5 -14BO -15BO
-134 -131 -123 -140 -140 -1400 -1400 -1400
225 250 2800 3150
-164 -150 -169 -212 -255 -1535 -1610 -1730
-151 -149 -138 -158 -158
250 280
-174 -181 -190 -239 -286
-153 -161 -150 -170 -170
280 315
-186 -193 -202 -251 -300
-183 -179 -159 -190 -190
315 355
-206 -215 -226 -279 -330
400
-201 -197 -187 -206 -200
355
-226 -233 -244 -297 -346
450
-225 -219 -209 -232 -232
400
-252 -259 -272 -329 -387
500
-245 -239 -229 -252 -252
450
-m -279 -292 -349 -407
18
ISO 286-2 : 1988 (El
:=~ := ~
- 18 - 18 - 400 - 400 - 400 - 600 - 600 - 600
=~
- 18
- 3
- 24 - 28 -43
500 560
- 444 - 470 - 510 - 644 - 670 - 710
3 6
=~
-20 - 19 -23 -23
-28 - 31 - 41 -53i= ~ 560 630
-
-
450
494
-
-
450
520
-
-
450
560
-
-
660
104
-
-
660
730
-
-
660
710
6 10
=~
-25 -22
-34 - >I := : := :
-28
-64
630 710
-
-
500
560
-
-
500
590
-
-
500
625
-
-
740
790
-
-
740
820
-
-
740
865
10 18
=: -30 - 26
- 41 -44 1= : I=,~
-33
- 76
710 800 -
-
560
610
-
-
560
640
-
-
560
685
-
-
840
890
-
-
840
920
-
-
640
965
18 24
=~
->I - 33
-50 - 54 :=~! I=,~
- 41
-93
800 900 -
-
620
676
-
-
620
710
- 620
- 780 -
- 840
996
- 840
-1030
- 940
-1060
24 30
I=~ := =
- >I
-50 ~ ~! =~
-44 -40
-57 - 61 =:: 1=,:
-48
- "JO
900 1000 -
-
680
736
-
-
680
710
-
-
680
820
-1050
-1106
-1050
-1140
-1050
-1190
30 40
1=~ i= :
-43
-59 =~ =~
- 55 - 51
- 71 - 76 =: 1=,:-60
-122
1000 1 120 -
-
780
846
-
-
100
885
-
-
100
945
-1150
-1216
-1 lSO
-1256
-T 150
-1315
I=~ 1=
- - - 840 -1300 -1300 -1300
~ =~ =~
-49 -65 - 61 - 70 - 70 840 840
40 50
-65 - 81 -86 -109 -132 I=,~ 1 120 1250
- 906 - 945 -1005 -1366 -1405 -1466
50 65
:=
-60
-79 ~ =,~
- 81 - 76 -87 -87
-100 -106 -133 -161 1=: 1250 1400 - 960
-1038
- 960
-1005
- 960
-1155
-1450
-1528
-1450
-1575
-1450
-1645
65 80
:=:: =,~
-69
-88
-96 - 91 -102 -102
-115 -121 -148 -176 1=: 1400 1800
-1050
-1128
-1050
-T 175
-1050
-1245
-1600
-1578
-1600
-1725
-1600
-1795
I=~
-1200 -1200 -1200 -1850
I=,~ =,~
100 -84 -117 -111 -124 -124
1800 1800 -1850 -1850
80
-106 -139 -146 -178 -211 -1292 -1350 -1430 -1942 -2000 -2060
100 120
- 97 - 91
-119 -126 =:: -m -131 -144 -144
-159 -166 -198 -231 :=: 1800 2000
-1350
-1442
-1350
-1500
-1350
-1580
-2000
-2092
-2000
-2150
-2000
-2230
120 140
-115 -107
-140 -147 =:~
-163 -155 -170 -170
-188 -195 -233 -270 :=: 2000 2240
-1500
-T 610
-1500
-1675
-1500
-1700
-2300
-2410
-2300
-2475
-2300
-2590
140 180
-127 -119
-152 -159 =:~
-183 -175 -190 -190
-208 -215 -253 -290 1=: 2240 2500
-1650
-1760
-1650
-1825
-1650
-1930
-2500
-2610
-2500
-2675
-2500
-2100
180 180
-139 -131
-164 -171 =: -203
-228 =: -m-210 -210
-310 1=~~ 2500 2800
-1900
-2035
-1900
-2110
-1900
-2230
-2900
-3035
-2900
-3"0
-2900
-3230
200 225
-171 -163
-200 -209 =: -249 -241 -258 -258
-278 -267 -330 -m 1=:
225 250
-187 -179
-216 -225 =: -275 -267 -284 -284
-304 -313 -356 -399 1=:
250 280 -209 -198
-241 -250=: -306 -295 -315 -315
-338 -347 -396 -445 I=~
280 315
-231 -220
-263 -m =~~
-341 -330 -350 -350
-m -382 -431 -480 1=:
315 355 -257 -247
-293 -304 =: -m -369 -390 -390
-415 -426 -479 -530 1=:
355 400 -263 -273
-319 -J:l)
=: -424 -414 -435 -435
-460 -471 -524 -575 1=:
400 450 -317 -3IJ7
-357 -370 =: -477 -467 -490 -490
-517 -530 -587 -645 :=:
450 500
-347 -337
-387 -400 =: -527 -517 -540 -540
-557 -580 -637 -695 1=:
1) Tolerance classes T5 to TB (jncl.) have not been tabulated for basic sizes less than or equal to 24 mmo It is recommended that tolerance classes U5 to ua
(incl.) be used instead. However, if tolerance classes T5 to TB (incl.) are especially required, they may be calculated from the bases given in ISO 286-1,
19
ISO 286-2: 1988 (E)
Basic alze
V 21 X y31
mm
Up to
Above and in- 5 6 7 8 5 6 7 8 9 10 6 7 8 9 10
cluding
- 3
-20 -20 - 20 - 20 - 20 - 20
- 24 - 26 - 30 - 34 - 45 -60
3 6
-7:/ - 25 - 24 -28 - 28 -28
- 32 - 33 - 36 -46 - 58 -76
- 32 - 31 -28 -34 -34 -34
6 10
- 38 -40 -43 -56 -70 -92
10 14
-37 -37 - 33 -40 -40 -40
-45 -48 - 51 -01 -83 -1'0
14 18
-38 -38 -32 -39 -42 -42 - 38 -45 -45 -45
-44 - 47 -50 - 66 - 50 - 53 - 56 - 72 - 88 -115
IS 24
-44 - 43 -39 - 47 - 51 - 50 - 46 - 54 - 54 -54 - 59 - 56 - 63 - 63 - 53
-53 - 56 -60 -00 -60 -63 - 01 - 87 - 1<)6 -138 - 72 - 76 - 96 -115 -147
24 30
-52 - 51 - 47 - 56 - 61 -60 - 56 -64 -64 -64 - 71 - 01 - 75 -75 - 75
-61 - 64 -68 -88 -70 -73 -n -97 -116 -148 - 84 - 88 - 1~ -17:/ -159
30 40
-64 - 63 -59 -68 - 76 -75 - 71 -00 - 00 -00 - 89 - 85 - 94 -94 -94
-75 - 79 -84 -107 -87 - 91 - 96 -119 -142 -HIJ - 105 - 110 - 133 -156 -194
40 50
-n - 76 -72 - 81 -93 - 92 - 88 -97 - 97 - 97 - 109 - 105 - 114 -,,4 -',4
-88 -92 - 97 -120 -104 -1~ -1'3 -136 -159 -197 - 125 - 130 - 153 -176 -214
50 65
-96 - 91 -102 -116 -111 -122 -122 - 138 - 133 - 144
-115 -121 -148 -135 -141 -168 -196 - 157 - 163 - 190
65 80
-114 -109 -120 -140 -135 -148 -148 - 168 - 163 - 174
-133 -139 -166 -159 -166 -192 -220 - 187 - 193 - 220
80 100
-139 -133 -146 -171 -166 -178 -178 - 207 - 201 - 214
-161 -168 -200 -193 -200 -232 -265 - 229 - 236 - 268
100 120
-165 -159 -172 -203 -197 -210 -210 - 247 - 241 - 254
-187 -194 -226 -226 -232 -264 -297 - 269 - 276 - 308
120 140
-196 -187 -202 -241 -233 -248 -248 - 293 - 2S5 - 300
-220 -227 -266 -266 -273 -31' -348 - 318 - 325 - 363
140 180
-221 -213 -228 -m -266 -280 -280 - 333 - 325 - 340
-248 -253 -291 -298 -306 -343 -380 - 358 - 365 - 403
•
-245 -237 -252 -303 -295 -310 -310 - 373 - 365 - 380
180 180
-7:/0 -7:17 -315 -329 -335 -373 -410 - 398 - 405 - 443
180 200
-7:/6 -"1ffI -284 -341 -333 -350 -350 - 416 - 408 - 425
-304 -313 -356 -370 -379 -422 -486 - 445 - 454 - 497
200 225 -301 -293 -310 -376 -368 -385 -385 - 481 - 453 - 470
-330 -339 -382 -405 -414 -457 -500 - 490 - 499 - 542
-331 -323 -340 -416 -408 -425 -425 - 511 - 503 - 520
225 250
-360 -369 -412 -445 -454 -497 -540 - 540 - 549 - 592
250 280
-376 -365 -386 -486 -455 -475 -475 - 571 - 560 - 580
-408 -417 -486 -498 -507 -556 -605 - 603 - 612 - 661
280 315
-416 -405 -425 -516 -505 -525 -525 - 641 - 630 - 560
-448 -457 -506 -548 -657 -506 -655 - 013 - 682 - 731
315 355 -484 -454 -475 -579 -569 -590 -590 - 719 - 709 - 730
-500 -511 -564 -615 -628 -679 -730 - 755 - 766 - 819
355 400
-519 -509 -!OO -649 -639 -560 -660 - 009 - 799 - 820
-565 -566 -619 -685 -696 -749 -800 - 845 - 856 - 909
400 450 -582 -572 -595 -w -717 -740 -740 - 907 - 897 - 920
-622 -835 -692 -701 -700 -837 -895 - 947 - 960 -1017
1) Fundamental deviations V, X and Y are not provided for basic sizes greater than 500 mmo
21 Toleranee classes V5 to va
(incl.) have not been tabulated for basic sizes less than or equal to 14 mmo It is recommended that toleranee classes X5
to xa
(incl.) be used instead. However, if toleranee classes V5 to va
(incl.) are especially required, they may be calculated from the bases given in
ISO 286-1,
3) Toleranee classes Y6 to VlO (incl.) have not been tabulated for basic sizes less than or equal to 18 mmo It is recommended that tolerance classes
Z6 to Z10 (incl.) be used instead. However, it toleranee classes Y6 to Y10 (incl.) are especially required, they may be calculated trom the bases given in .
ISO 286-1,
20
ISO 286-2 : 1988 (E)
Basic slza Z ZA
mm
Up to
Above and in- 6 7 8 9 ,0 6 7 8 9 ,0
cluding " "
- 3 -26 - 26 - 26 - 26 - 26 - 26 -32 - 32 - 32 - 32 - 32 - 32
-32 - 36 - 40 - 51 - 66 - 86 -38 - 42 - 48 - 57 - 72 - 92
3 6
-32 - 31 - 35 - 35 - 35 - 35 -39 - 38 - 42 - 42 - 42 - 42
-40 - 43 - 53 - 66 - B3 - 110 - 47 - 50 - 00 - 72 - 90 - 117
6 10 - 39 - 36 - 42 - 42 - 42 - 42 -49 - 48 - 52 - 52 - 52 - 52
-48 - 51 - 64 - 78 - 100 - 132 -58 - 61 - 74 - 88 - 110 - 142
10 14 - 47 - 43 - 50 - 50 - 50 - 50 - 61 - 57 - 64 - 64 - 64 - 64
- n -
•
- 58 - 61 - 93 - 120 - 160 -72 - 75 - 91 - 107 134 - 174
,. 18 - 57
- 68
-
-
53
71
-
-
60
87
-
-
60
103
-
-
60
130
-
-
60
170
- 74
-85
-
-
70
88
-
-
77
104
-
-
77
120
-
- 147
n -
- 187
n
18 24 - 69 - 66 - 73 - 73 - 73 - 73 -94 - 90 - 98 - 98 - 98 - 98
-82 - 86 - 106 - 125 - 157 - 203 -107 - 111 - 131 - 150 - 182 - 228
24 30
- 94 - 90 - 88 - 88 - 88 - 88 -114 - 110 - 118 - 118 - 118 - 118
- 97 - 101 - 121 - 140 - 172 - 218 -127 - 131 - 151 - 170 - 202 - 248
30 40 -107 - 103 - 112 - 112 - 112 - 112 -143 - 139 - 148 - 148 - 148 - 148
-123 - 128 - 151 - 174 - 212 - 272 -159 - 164 - 187 - 210 - 248 - 308
40 50 -131 - 127 - 136 - 138 - 136 - 136 -175 - 171 - 180 - 180 - 180 - 180
-147 - 152 - 175 - 198 - 238 - 296 -191 - 198 - 219 - 242 - 280 - 340
50 65 - 161 - 172 - 172 - 172 - 172 - 215 - 226 - 226 - 226 - 226
- 191 - 218 - 248 - 292 - 362 - 245 - 272 - 300 - 345 - 416
65 80
- 199 - 210 - 210 - 210 - 210 - 263 - 274 - 274 - 274 - 274
- 229 - 256 - 284 - 330 - 400 - 293 - 320 - 348 - 394 - 484
80 100 - 245 - 258 - 258 - 258 - 258 - 322 - 335 - 335 - 335 - 335
- 280 - 312 - 345 - 398 - 478 - 357 - 389 - 422 - 475 - 555
100 120 - 297 - 310 - 310 - 310 - 310 - 387 - 400 - 400 - 400 - 400
- 332 - 364 - 397 - 450 - 530 - 422 - 464 - 487 - 540 - 620
120 140 - 360 - 365 - 365 - 365 - 366 - 455 - 470 - 470 - 470 - 470
- 390 - 428 - 465 - 525 - 615 - 495 - 533 - 570 - 630 - 720
140 160 - 400 - 415 - 415 - 415 - 415 - 520 - 535 - 535 - 535 - 535
- 440 - 478 - 515 - 575 - 666 - 560 - 598 - 635 - 696 - 785
160 180 - 450 - 455 - 465 - 465 - 455 - 585 - 600 - 600 - 600 - 600
- 490 - 528 - 566 - 625 - 715 - 625 - 663 - 700 - 700 - 860
180 200 - 503 - 520 - 520 - 520 - 520 - 663 - 670 - 870 - 870 - 670
- 649 - 592 - 635 - 705 - 810 - 699 - 742 - 785 - 855 - 960
200 225 - 558 - 575 - 575 - 575 - 575 - 723 - 740 - 740 - 740 - 740
- 604 - 647 - 690 - 750 - 865 - 769 - 812 - 855 - 925 -1030
225 250 - 623 - 640 - 640 - 640 - 640 - 803 - 820 - 820 - 820 - 820
- 669 - 712 - 755 - 825 - 930 - 849 - 892 - 935 -1005 -1110
250 280 - 690 - 710 - 710 - 710 - 710 - 900 - 920 - 920 - 920 - 920
- 742 - 791 - 640 - 920 -1030 - 962 -1001 -1050 -1130 -1240
- 770 - 790 - 790 - 790 - 790 - 980 -1000 -1000 -1000 -1000
280 315
- 822 - 871 - 920 -1000 -1110 -1032 -1081 -1130 -1210 -1320
- 879 - 900 - 900 - 900 - 900 -1129 -1150 -1 150 -1150 -1150
315 355
- 936 - 989 -1040 -1130 -1260 -1186 -1239 -1290 -1380 -1510
400 - 979 -1000 -1000 -1000 -1000 -1279 -1300 -1300 -1300 -1300
355 -1230 -1440
-1038 -1009 -11-40 -1360 -1336 -1389 -1530 -1660
400 450 -1on -1100 -1100 -1100 -1100 -1427 -1450 -1450 -1450 -1450
-1140 -1197 -1255 -1350 -1500 -1490 -1547 -1606 -1700 -1860
-1227 -1250 -1250 -1250 -1250 -1577 -1600 -1600 -1600 -1600
450 500
-1290 -1347 -1405 -1500 -1660 -1640 -1697 -1155 -1860 -2000
1) Fundamental devlatlons Zand ZA are not provlded for baSIC slzes greater than 500 mmo
21
I~O 286-2 : 1988 (EI
Basic size
ZB ze
mm
Up to
Above and in- 7 8 9 tO 11 7 8 9 10 11
cluding
- 3 - 40 - 40 - 40 - 40 - 40 - 00 - 00 - 00 - 00 - 60
- 50 - 54 - 65 - 00 - 100 - 70 - 74 - 85 - 100 - 120
3 6 - 46 - 50 - 50 - 50 - 50 - 76 - 00 - 00 - 00 - 00
- 58 - 58 - 00 - 98 - 125 - 88 - 98 - 110 - 128 - 155
6 10
- 61 - 67 - 67 - 67 - 67 - 91 - 97 - 97 - 97 - 97
- 76 - 89 - 1()3 - 125 - 157 - 106 - 119 - 133 - 155 - 167
•
117 157 173 200
14 18 - 101 - 108 - 108 - 108 - 108 - 143 - 150 - 150 - 150 - 150
- 119 - 135 - 151 - 179 - 218 - 161 - 177 - 193 - 220 - 260
18 24 - 128 - 136 - 136 - 136 - 136 - 180 - 188 - 198 - 188 - 188
- 149 - 169 - 188 - 220 - 268 - 201 - 221 - 240 - 2n - 318
24 30 - 152 - 160 - 100 - 100 - 100 - 210 - 218 - 218 - 218 - 218
- 173 - 193 - 212 - 244 - 290 - 231 - 251 - 270 - 302 - 346
30 40
- 191 - 200 - 200 - 200 - 200 - 265 - 274 - 274 - 274 - 274
- 216 - 239 - 262 - 300 - 300 - 290 - 313 - 336 - 374 - 434
40 50 - 233 - 242 - 242 - 242 - 242 - 316 - 325 - 325 - 325 - 325
- 258 - 281 - 304 - 342 - 402 - 341 - 364 - 367 - 425 - 485
50 65 - 289 - 300 - 300 - 300 - 300 - 394 - 405 - 405 - 405 - 405
- 319 - 346 - 374 - 420 - 490 - 424 - 451 - 479 - 525 - 595
65 80
- 349 - 360 - 300 - 360 - 300 - 469 - 49l - 400 - 400 - 49l
- 379 - 406 - 434 - 400 - 550 - 499 - 525 - 554 - 600 - 670
80 100
- 432 - 445 - 445 - 445 - 445 - 572 - 585 - 585 - 585 - 585
- 467 - 499 - 532 - 585 - 665 - 607 - 639 - 672 - 725 - 805
100 120 - 512 - 525 - 525 - 525 - 525 - 677 - 690 - 690 - 690 - 690
- 547 - 579 - 612 - 665 - 745 - 712 - 744 - m - 830 - 910
120 140
- 665 - 620 - 620 - 620 - 620 - 795 - 800 - 000 - 800 - 600
- 645 - 683 - 720 - 790 - 670 - 825 - 863 - 000 - 900 -1050
140 160
- 685 - 700 - 700 - 700 - 700 - 885 - 900 - 000 - 900 - 900
•
- 725 - 793 - 000 - aoo - 950 - 925 - 963 -1000 -1060 -1150
160 180
- 785 - 790 - 790 - 790 - 790 - 985 -1000 -1000 -1000 -1000
- 005 - 643 - 880 - 940 -1030 -1025 -1063 -1100 -1160 -1250
180 200 - 863 - 880 - 880 - 880 - 880 -1133 -1150 - t 150 -1150 -1150
- 909 - 952 - 995 -1065 -1170 -1179 -1222 -1265 -1335 -1440
- 943 - 900 - 900 - 900 - 900 -1233 -1250 -1250 -1250 -1250
200 225
- 989 -1032 -1075 -1145 -t 250 -1279 -1322 -1365 -1435 -1540
-1033 -1060 -1050 -1050 -1060 -1333 -1350 -t 350 -1350 -1350
225 250
-1079 -1 122 -1166 -1235 -1340 -1379 -1422 -1465 -1535 -1640
-1100 -1200 -1200 -1200 -1200 -1530 -1550 -1550 -1550 -1550
250 280
-1232 -1281 -1330 -1410 -1520 -1582 -1631 -1600 -1 76IJ -1870
-1280 -1300 -1300 -1300 -1300 -1680 -1700 -1700 -1700 -1700
280 315
-1332 -1381 -1430 -1510 -1620 -1732 -1781 -1830 -1910 -2020
-1479 -1500 -1500 -1500 -1500 -1679 -1900 -1000 -1900 -1900
315 355
-1536 -1589 -1640 -1730 -1 aoo -1936 -1989 -2040 -2130 -2260
-1629 -1650 -1650 -1850 -1850 -2079 -2100 -2100 -2100 -2100
355 400
-1586 -1739 -1790 -1880 -2010 -2136 -2189 -2240 -2330 -2460
-1827 -1850 -1850 -1860 -1860 -2377 -2400 -2400 -2400 -2400
400 450
-1890 -1947 -2005 -2100 -2250 -2440 -2497 -2555 -2650 -2800
-2077 -2100 -2100 -2100 -2100 -2677 -2600 -2600 -2600 -2600
450 500
-2140 -2197 -2255 -2350 -2500 -2640 -2697 -2755 -2860 -3000
1) Fundamental devIatIOns ZB and ze are not provlded tor baSIC sizes greater than 500 mmo
22
ISO 286-2: 1988 (El
- 3 2) - 270 - 270 - 270 - 270 - 270 -140 -140 - 140 - 140 - 140 - 140 -60 - 60 -60 - 60 - 60
- 295 - 310 - 330 - 370 - 410 -154 -165 - "") - 200 - 240 - 280 - 74 -85 -100 -120 - 160
3 6 - 270 - 270 - 270 - 270 - 270 -140 -140 - 140 - 140 - 140 - 140 - 70 -10 - 70 -10 - 10
- 300 - 318 - 345 - 300 - 460 -158 -110 - 188 - 215 - 260 - 320 -88 -100 -118 -145 - 190
6 10 - 280 - 280 - 280 - 280 - 280 -160 -160 - 150 - 150 - 150 - 150 -60 -80 -60 -80 - 60
- 316 - 338 - 370 - 430 - 500 -In -186 - 208 - 240 - 300 - 370 -102 -116 -138 -170 - 230
10 18 - 290 - 290 - 290 - 290 - 290 -150 -150 - 150 - 150 - 150 - 150 -95 - 95 -95 -95 - 95
- 333 - 360 - 400 - 470 - 500 -In -193 - 220 - 260 - 330 - 420 -122 -138 -165 -205 - 275
8 30 - 300 - 300 - 300 - 300 - 300 -160 -160 - 160 - 160 - 160 - 160 -110 -110 -110 -110 - 110
- 352 - 384 - 430 - 510 - 630 -193 -212 - 244 - 290 - 370 - 400 -143 -'62 -194 -240 - 320
30 40 - 310 - 3'0 - 310 - 310 - 3'0 -170 -170 - 170 - '70 - 110 - '70 -120 -120 -120 -120 - 120
- 372 - 4'0 - 470 - 560 - 700 -209 -232 - 270 - 330 - 420 - 500 -159 -'62 -220 -280 - 370
40 50
- 320 - 320 - 320 - 320 - 320 -'60 -'60 - 160 - '80 - '80 - 160 -'30 -'30 -130 -'30 - 130
- 382 - 420 - 460 - 570 - 7'0 -219 -242 - 280 - 340 - 430 - 570 -1'" -192 -230 -290 - 360
50 65 - 340 - 340 - 340 - 340 - 340 -190 -190 - '90 - '90 - '90 - '90 -140 -,40 -140 -'40 - 140
- 414 - 460 - 530 - 840 - 600 -236 -264 - 310 - 380 - 400 - 650 -186 -214 -260 -330 - 440
- 360 - 360 - 360 - 360 - 360 -200 -200 - 200 - 200 - 200 - 200 -150 -'50 -'50 -'50 - 150
65 80
- 434 - 460 - 550 - 650 - 820 -246 -274 - 320 - 300 - 500 - 660 -196 -224 -210 -340 - 460
80 100 - 360 - 380 - 380 - 380 - 360 -220 -220 - 220 - 220 - 220 - 220 -170 -170 -'70 -170 - 170
- 467 - 520 - 600 - 730 - 920 -274 -307 - 360 - 440 - 570 - 760 -224 -257 -310 -300 - 520
100 120 - 4'0 - 4'0 - 4'0 - 4'0 - 4'0 -240 -240 - 240 - 240 - 240 - 240 -160 -'60 -'60 -'60 - '60
- 497 - 550 - 630 - 760 - 950 -294 -327 - 360 - 460 - 590 - 780 -234 -267 -320 -400 - 530
120 140 - 460 - 460 - 460 - 460 - 460 -260 -260 - 260 - 260 - 260 - 260 -200 -200 -200 -200 - 200
- 560 - 620 - 710 - 860 -1090 -323 -360 - 420 - 510 - 650 - 890 -293 -300 -360 -460 - 600
140 150 - 520 - 520 - 520 - 520 - 520 -280 -280 - 280 - 280 - 280 - 280 -210 -210 -210 -210 - 210
- 820 - 680 - 710 - 920 -1150 -343 -360 - 440 - 530 - 680 - 9'0 -m -310 -370 -460 - 6'0
160 180 - 560 - 580 - 560 - 560 - 560 -310 -310 - 310 - 3'0 - 310 - 310 -230 -230 -230 -230 - 230
- 660 - 740 - 630 - 980 -1210 -373 -410 - 470 - 560 - 710 - 940 -293 -330 -300 -480 - 630
200 - 660 - 650 - 650 - 660 - 660 -340 -340 - 340 - 340 - 340 - 340 -240 -240 -240 -240 - 240
- 715 - 845 - 950 -1120 -1380 -412 -455 - 525 - 630 - 600 -, 060 -312 -355 -425 -530 - 700
200 225
- 740 - 740 - 740 - 740 - 740 -380 -360 - 360 - 380 - 380 - 360 -260 -260 -260 -260 - 260
- 855 - 925 -, 030 -, 200 -'460 -452 -495 - 565 - 670 - 940 -1100 -332 -375 -445 -550 - 720
225 250 - 820 - 820 - 820 - 820 - 820 -420 -420 - 420 - 420 - 420 - 420 -280 -280 -280 -280 - 280
- 935 -, 005 -1110 -'280 -, 540 -492 -535 - 605 - 7'0 - 880 -1140 -352 -395 -465 -570 - 740
250 280
- 920 - 920 - 920 - 920 - 920 -480 -480 - 480 - 460 - 480 - 480 -300 -300 -300 -300 - 300
-, 050 -1130 -1240 -1440 -, 730 -56' -610 - 590 - 600 -1000 -, 290 -381 -430 -510 -620 - 820
280 315 -1050 -, 050 -, 050 -1050 -, 050 -540 -540 - 540 - 540 - 540 - 540 -330 -330 -330 -330 - 330
-1 100 -, 260 -1370 -1570 -'860 -621 -670 - 750 - 860 -, 060 -, 350 -411 -460 -540 -650 - 850
315 355
-, 200 -1200 -, 200 -'200 -1200 -600 -600 - 600 - 600 - 600 - 600 -360 -360 -350 -360 - 360
-, 340 -'430 -, 560 -1770 -2090 -sm -740 - 630 - 960 -1 170 -, 400 -449 -500 -590 -720 - 930
355 400
-, 350 -'350 -'350 -1350 -, 350 -660 -660 - 660 - 660 - 660 - 660 -400 -400 -400 -400 - 400
-, 490 -, 580 -1710 -1920 -2240 - 7'" -820 - 9'0 -, 040 -, 250 -1670 -489 -540 -630 -761) - 970
-, 500 -, 500 -, 500 -, 500 -, 500 -760 -761) - 760 - 760 - 760 - 760 -440 -440 -440 -440 - 440
400 450
-, 656 -, 750 -, 900 -2130 -2470 -957 -91S -1010 -1160 -, 300 -, 730 -537 -595 -590 -940 -1070
450 500
-, 650 -1650 -, 650 -1650 -, 650 -840 -840 - 940 - 940 - 940 - 940 -460 -480 -480 -480 - 480
-, 806 -1900 -2050 -2280 -2620 -937 -995 -, 090 -1240 -1470 -1810 -577 -935 -730 -880 -1110
1) Fundamental deviations a, band c are not provided for basic sizes greater than 500 mmo
2) Fundamental deviations a and b shall not be used for any standard tolerance grades in basic sizes less than or equal to 1 mmo
23
ISO 286-2 : 1988 (EI
Basic siza cd 1) d
mm
Up to
Above and in- 5 6 7 8 9 10 5 6 7 8 9 10 11 12 13
cluding
-55 -55 -55 -55 -55 -55 -40 -40 -40 -40 - 40 - 40 - 40 ..40 - 40
6 10
-62 -65 -71 -78 -92 -',4 - 46 -49 - 55 -62 - 76 - 98 - 130 -100 - 260
'0 '8
-50 - 50 - 50 - 50 - 50 - 50 - 50 - 50 - 50
•
-58 - 61 - 68 -77 - 93 - 120 - 160 -230 - 320
'8 30 -65 - 65 - 65 - 65 - 65 - 65 - 65 - 65 - 65
- 74 -78 -86 - 98 - 117 - 149 - 195 -275 - 395
30 50
- 80 -00 - 80 -00 - 00 - 80 - 80 - 00 - 80
- 91 -98 -105 -119 - 142 - 100 - 240 -330 - 470
80 '20
-120 -120 -120 -120 - 120 - 120 - 120 -120 - 120
-135 -142 -156 -174 - 207 - 260 - 340 -470 - 660
'20 '80
-145 -145 -145 -145 - 145 - 145 - 145 -145 - 145
-163 -170 -185 -200 - 245 - 306 - 395 -545 - 775
'80 250
-170 -170 -170 -170 - 170 - 170 - 170 -170 - 170
-190 -199 -216 -242 - 285 - 356 - 460 -630 - 890
250 3'5
-190 -190 -190 -190 - 190 - 190 - 190 -100 - 190
-213 -222 -242 -271 - 320 - 400 - 510 -710 -1000
400 -210 -210 -210 -210 - 210 - 210 - 210 -210 - 210
3'5 -
-235 -246 -267 -299 - 350 - 440 570 -780 -1100
400 500 -230 -230 -230 -230 - 230 - 230 - 230 -230 - 230
-257 -270 -293 -327 - 385 - 480 - 630 -860 -1200
500
630
800
630
800
'000
-260
-330
-290
-370
-320
-410
-260
-370
-290
-415
-320
-460
-
-
-
-
-
-
260
435
290
490
320
550
- 260
-
-
-
-
-
540
290
610
320
680
-
-
- 290
-
-
- 980
260
700
790
320
•
'000 '250
-350 -350 - 350 - 350 - 350
-455 -515 - 610 - 770 -1010
-300 -300 - 300 - 300 - 300
'250 '800 -515 -685 - 700 - -1170
890
2500 3'50
-620 -520 - 620 - 520 - 520
-730 -850 -1060 -1380 -1870
1) The intermediate fundamental deviation cd is provided primarily tor fine mechanisms and horology. If tolerance classes involving this fundamental
deviation in other basic sizes are required, they may be calculated in accordance with ISO 286-1.
24
ISO 286-2: 1988 (El
Basic size
mm
• al1)
Up to
Above and in· 5 6 7 6 9 10 3 4 5 6 7 B 9 10
cluding
- 3 - 14 - -
" - 14 - 14 - I. -10 -10 -10 -10 -10 -10 -10 -10
- 18 "
- 20 - 24 -28 - 39 - 54 -12 -13 -14 -16 -20 -24 -35 -50
-20 - 20 - 20 -20 - 20 - 20 -14 -14 -14 -14 -I' -I' -14 -14
3 6
-25 - 28 -32 -38 - 50 - sa -16.5 -18 -19 -22 -26 -32 -44 -62
-25 - 25 -25 -25 - 25 - 25 -18 -18 -18 -18 -18 -18 -18 -18
6 10
- 31 - 34 -40 - 47 - 61 - 83 -20.5 -22 -24 -27 -33 -40 -54 -76
-32 - 32 -32 -32 - 32 - 32
•
10 18
-40 - 43 -50 - 59 - 75 - 102
-40 - 40 -40 -40 - 40 - 40
18 30
-49 -53 - 61 - 73 -92 - 124
- 50 -50 - 50 - 50 - 50 - 50
30 50
- 61 -66 - 75 -89 -112 - 150
-60 -60 -60 - 60 -60 - 60
50 80
-73 - 79 -90 -HlS -134 - 180
• 500
630
800
630
800
1 ()()()
-145
-189
-160
-210
-170
-226
-145
-215
-160
-240
-170
-260
-145
-255
-160
-285
-170
-310
-145
-320
-160
-360
-170
-400
-
-
-
-
-
-
145
'25
160
480
170
530
2 ()()() 2500
-260 -260 -260 -260 - 260
-370 -435 -540 -700 - 960
-290 -290 -290 -290 - 290
2500 3150
-425 -500 -620 -830 -1150
..
1) The Intermedlate fundamental deviatlon ef IS provlded pnmanly tor fine mechamsms and horology. It toleranee classes Involvlng this fundamental
deviation in ether basic sizes are required, they may be calculated in accordance with ISO 286-1.
25
ISO 286-2: 1988 (EI
Basic aiza Ig 1l
I
mm
Up to
Above and in- 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
cluding
- 3
- 6 - 6 - 6 - 6 - 6 - 6 - 6 - 6 - 4 - 4 - 4 - 4 - 4 - 4 - 4 - 4
- 8 - 9 -10 - 12 - 16 - 20 - 31 - 46 - 6 - 7 - 8 -10 -14 -18 -29 -44
3 6
-10 -10 -10 - 10 - 10 - 10 - 10 - 10 - 6 - 6 - 6 - 6 - 6 - 6 - 6 - 6
-12,5 -14 -15 - 18 -22 -28 - 40 - 58 - 8.5 -10 -11 -14 -18 -24 -36 -54
6 10
-13 -13 -13 - 13 - 13 - 13 - 13 - 13 - 8 - 8 - 8 - 8 - 8 - 8 - 8 - 8
-15,5 -17 -19 -22 - 28 - 35 -48 - 71 -10,5 -12 -14 -17 -23 -30 -44 -66
-16 -16 -16 - 16 - 16 - 16 - 16 - 16
•
10 18
-19 -21 -24 -27 -34 -43 - 56 - 86
-20 -20 -20 -20 -20 - 20 - 20 - 20
18 30
-24 -26 -29 -33 - 41 - 53 - 72 -104
30 50
-25 -25 -25 - 25 -25 - 25 -25 - 25
-29 -32 -36 - 41 -50 - 64 -87 -125
-30 -30 -30 -30 -30 - 30
50 80
-38 -43 -48 -60 - 76 -104
500
630
BOO
630
BOO
1000
- 76
-120
-80
-130
-86
-142
- 76
-146
-80
-160
-86
-176
- 76
-186
- 80
-206
-86
-226
- 76
-251
- 80
-280
-86
-316
•
-98 - 98 -98 -98
1000 1250
-164 -203 -253 -368
-110 -110 -110 -110
1250 1600
-188 -235 -305 -420
-120 -120 -120 -120
1500 2000
-212 -270 -350 -480
-130 -130 -130 -130
2000 2500
-240 -305 -410 -570
-146 -146 -146 -145
2500 3150
-280 -355 -475 -685
-. - .
1) The Intermedlate fundamental devlatlon tg IS provlded pnmanly tor fine mechanlsms and horology. 11 tolerance classes Involvlng thls fundamental
deviation in ather basic sizes are required, they may ba calculated in accordance with ISO 286-1.
26
ISO 286-2: 1988 IE)
Basic Biza
9
mm
Up to
Above and in- 3 4 5 6 7 8 9 10
cluding
- 2 - 2 - 2 - 2 - 2 - 2 - 2 - 2
- 3
- 4 - 5 - 6 - 8 - 12 - 16 -TI - 42
3 6 - 4 - 4 - 4 - 4 - 4 - 4 - 4 - 4
- 6,5 - 8 - 9 - 12 - 16 -22 -34 - 52
- 5 - 5 - 5 - 5 - 5 - 5 - 5 - 5
6 '0 - 7,5 - 9 -11 - 14 -20 -27 -41 - 63
- 6 - 6 - 6 - 6 - -
•
6 - 6 - 6 6
'0 '8 - 9 -11 -14 - 17 - 24 - 33 -49 - 76
'8 30
- 7 - 7 - 7 - 7 - 7 - 7 - 7 - 7
-11 -13 -16 -20 -28 -40 -59 - 91
30 50 - 9 - 9 - 9 - 9 - 9 - 9 - 9 - 9
-13 -16 -20 - 25 - 34 -48 -71 -109
50 BO -10 -10 - 10 - 10 - 10
-18 -23 -29 -40 - 56
BO -12 -12 - 12 - 12 - 12
'20
-22 -TI -34 - 47 - 66
• 500
630
BOO
630
800
-22
-66
- 24
- 74
-26
-22
- 92
- 24
-104
- 26
-22
-132
- 24
-149
- 26
'000 -82 -116 -166
-26 - 28 - 28
'000 '250
-94 -133 -193
2500 3'50
-38 -38 - 38
-173 -248 -368
ISO 286-2 1988 (El
Basic size h
mm 1 2 3 4 5 6 7 8 9 10 11 12 13 1411 15" 16 1 17 18
'
Up to
Deviations
Above and in-
cluding ~m mm
3 1 0 0 0 0 0 0 0 0
~,2
0 0 0 0 0 0 0
- ' -0,8 - - 2 - 3 - 4 - 6 - 10 - 14 -25 -40 - 60 -0,1 -0,14 -0,25 -0,4 - 0,6
0 0 0 0 0 0 0 0
~,5 1- ~,5
3 6 0 0 0 0 0 0 0 0
-1 - - 4 - 5 - 8 - 12 - 18 - 30 -48 - 75 -0,12 -0,18 -0,3 -0,48 - 0,75 - 1.2 - 1,8
0 0 0 0 0 0 0 0 0 0 0
~,5
6 10 0 0 0 0 0 0
-1 - 1,5 1- - 4 - 6 - 9 - 15 - 22 -36 -58 - 90 -0,15 -0,22 -0,36 -0.58 - 0,9 - 1,5 - 2,2
-.
10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
18
-1,2 - 2 - 3 - 5 - 8 - 11 - 18 - 27 -43 - 70 - 110 -0,18 -0,27 -0,43 -0,7 - 1,1 - 1,8 - 2,7
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
18 30
-1,5 - 2,5 - 4 - 6 - 9 - 13 - 21 -33 - 52 -84 - 130 -0,21 -0,33 -0,52 -0,84 - 1,3 - 2,1
30 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
50
-1,5 - 2,5 - 4 - 7 -11 - 16 -25 -39 -62 -100 - 160 -0,25 -0,39 -0,62 -1 - 1,6 - 2,5 - 3,9
50 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
80
-2 - 3 - 5 - 8 -13 - 19 -30 - 46 - 74 -120 - 190 -0,3 -0,46 -0,74 -1.2 - 1,9 - 3 - 4,6
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
80 120
-2,5 - 4 - 6 -10 -15 - 22 -35 -54 - B7 -140 - 220 -0,35 -0.54 -0,87 -1,4 - 2,2 - 3,5 - 5,4
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
120 180
-3,5 - 5 - 8 -12 -18 - 25 -40 -63 -100 -160 - 250 -0,4 -0,63 -1 -1,6 - 2,5 - 4 - 6,3
0 ,0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
180 250
-4,5 - 7 -10 -14 -20 -29 -46 - 72 -115 -185 - 290 -0,46 -0.72 -1,15 -1.85 - 2,9 - 4,6 - 7,2
0 0 0 0
-~
250 315 0 0 0 0 0 0 0 0 0 0 0 0 0
-6 - 8 -12 -16 -23 - 32 - 52 - 81 -130 -210 -0,52 -0,S1 -1,3 -2.1 - 3,2 - 5,2 - 8,1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
315 400
-7 - 9 -13 -18 -25 - 36 - 57 -89 -140 -230 - 360 -0,57 -0,89 -1,4 -2,3 - 3,6 - 5,7 - 8,9
0 0 0 0
-~
400 0 0 0 0 0 0 0 0 0 0 0 0 0
500
-8 -10 -15 -20 -27 -40 -63 - 97 -155 -250 -0,63 -0,97 -1,55 -2,5 - 4 - 6,3 - 9,7
21
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
500 630
- 9 -11 -16 -22 -32 -44 - 70 -110 -175 -280 - 440 -0,7 -1,1 -1,75 -2.8 - 4,4 - 7 -1
0 0 0 0 0 0
~
630 800 0 0 0 0 0 0 0 0 0 0 0
-10 -13 -18 -25 -36 - 50 -80 -125 -200 -320 - -0,8 -1,25 -2 -3,2 - 5 - 8 -12,5
800 1000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-11 -15 -21 -28 -40 - 56 -90 -140 -230 -360 - 560 -0,9 -1.4 -2,3 -3,6 - 5,6 - 9 -I'
1000 1250 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-13 -18 -24 -33 -47 -56 -105 -165 -260 -420 - 660 -1,05 -1,65 -2,6 -4,2 - 6,6 -10,5 -16,5
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1250 1600
-15 -21 -29 -39 -55 -78 -125 -195 -310 -500 - 780 -1,25 -1,95 -3,1 -5 - 7,8 -12,5 -19,5
0 0 0 0 0 0 0
-~
1600 2000 0 0 0 0 0 0 0 0 0 0
-18 -25 -35 -46 -65 - 92 -150 -230 -370 -600 -1,5 -2,3 -3,7 -6 - 9,2 -15 -23
0 0
-~
2000 2500 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-30 -41 -55 -78 -110 -175 -290 -440 -700 -1100 -1,75 -2,8 -4,4 -7 -11 -17,5 -28
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2500 3150
-26 -36 -50 -68 -96 -135 -210 -330 -540 -860 -1350 -2,1 -3,3 -5,4 -8,6 -13,5 -21 -33
1) Tolerance grades lT14 to IT16 (Incl.) shall not be used tor baSIC srzes less than or equal to 1 mmo
21 The values given in the frame, tor tolerance grades ITl to IT5 (incl.), tor basic sizes greater than 500 mm and less than or equal to 3 150 mm, are included
tor experimental use.
28
,\
•Table 23 - Limit deviatio"s 1) tor shafts js
Upper limit deviation = es
•
Lower limit deviation = ei
Basic size j s 2)
mm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 31 15 31 1631 17 18
Up to
Oeviations
Above and in-
cluding ~m mm
- 3 31 ±OA ±O,6 ±1 ± 1,5 ± 2 ± 3 ± 5 ± 7 ± 12,5 ±2O ±30 ±Q,05 ta,07 ±O,125 ±O,2 tO,3
3 6 ±a,s ±O,75 ±1,25 ± 2 ± 2,5 ± 4 ± 6 ± 9 ± 15 ± 24 ± 37,5 ia,06 ±a,09 ±O,15 ±O,24 tO,375 ± 0,6 ± 0,9
6 10 ia,S ±O,75 +1,25 ± 2 ± 3 ± 4,5 ± 7,5 ± 11 ± 18 ±29 ± 45 ±a,07S tD,'T ta,t8 ±O,29 ±O,4S ± 0,75 ± 1,1
10 18 ±O,6 ±1 ±l,S ± 2,5 ± 4 ± 5,5 ± 9 ± 13,5 ± 21,5 ±35 ± 55 ±a,09 ±O,l35 ±Q,2tS ±O,35 tO,55 ± 0,9 ± 1,35
18 30 ±O,75 ±1,25 ±2 ± 3 ± 4,5 ± 6,5 ± 10,5 ± 16,5 ±26 ± 42 ±65 ±O,T05 ±O,l65 ±O,26 ±O,42 ±a,ss ± 1,05 ± 1,65
30 50 iO,75 ±1,25 ±2 ± 3,5 ± 5,5 ± 8 ± 12,5 ± 19,5 ± 31 ± 50 ±OO iO,l25 ±O,19S ±O,31 ±O,S ±a,s ± 1,25 ± 1,95
50 SO ±1 +1,5 ±2,5 + 4 ± 6,5 ± 9,5 ± 15 ±23 ± 37 ± 50 ±95 ±O,15 ±O,23 tO,37 ±O,6 ta,95 + T,5 ± 2,3
SO 120 ±1,25 ±2 ±3 + 5 ± 7,5 +11 ± 17,5 ± 27 ± 43,5 ± 70 +110 ±O,175 ±O,27 tO,435 i 0.] iT,T ± 1,75 ± 2,7
120 ISO ±1,75 ±2,5 ±4 ± 6 ± 9 ±12,5 ±2O ± 31,5 ±50 ±OO ±125 ±0,2 ±0,315 ±0,5 ±0,8 ±1,25 ± 2 ± 3,15
ISO 250 ±2,25 ±3,5 ±5 ± 7 ±10 ±14,5 ±23 ±36 ± 57,5 ± 92,5 ±145 ±0,23 ±0,36 ±0,575 ±0,925 ±1,45 ± 2,3 ± 3,6
250 315 ±3 ±4 ±6 ± 8 ±",5 ±16 ± 26 ± 40,5 ±65 ±105 ± 160 ±0,26 ±0,405 ±0,65 ±1,05 ±1,6 ± 2,6 ± 4,05
315 400 ±3,5 ±4,5 ±6,5 ± 9 ±12,5 ±18 ± 28,5 ± 44,5 ± 70 ± 115 ± 100 ±0,285 ±O,445 ±0,7 ±1,15 ±1,8 ± 2,85 ± 4,45
400 500 ±4 ±5 ±7,5 ±10 ±13,5 ±2O ± 31,5 ± 48,5 ± n,s, ±125 ±2OO ±0,315 ±0,485 ±0,n5 ±1,25 ±2 ± 3,15 ± 4,85
41
500 630 ± 4,5 ± 5,5 ± 8 ±11 ±16 ±22 ±35 ± 55 ± 87,5 ±140 ±220 ±0,35 ±0,55 ±0,875 ±1,4 ±2,2 ± 3,5 ± 5,5
630 SOO ± 5 ± 6,5 ± 9 +12,5 ±18 ±25 ±40 ± 62,5 ± 100 ±160 ±25O ±O,4 ±0,625 ±1 ±1,6 ±2,5 ± 4 ± 6,25
800 1 000 ± 5,5 ± 7,5 ±10,5 ±14 +20 ±28 ± 45 ± 70 ±115 ±100 ±280 ±0,45 ±0,7 ±1,15 ±1,8 ±2,8 ± 4,5 ± 7
1000 1250 ± 6,5 ± 9 ±12 i16,5 i23,5 ±33 ± 52,5 i 82,5 ±130 i210 ±33O ±O,525 ±0,825 i 1,3 i2,1 i 3,3 i 5,25 ± 8,25
1250 1 600 + 7,5 ±10,5 +14,5 i19,5 ±27,5 ±39 i 62,5 ± 97,5 ±155 ±25O ±390 ±0,625 ±0,915 il,55 i2,5 i3,9 i 6,25 ± 9,75
1600 2 000 ± 9 i 12,5 ±17,5 ±23 i32,5 +46 ± 75 + 115 ±185 ±3OO ±450 ±0,75 ±1,15 ±l,B5 ±3 i4,6 i 7,5 ±1',5
2 ()()() 2500 ±11 ± 15 ±20,5 ±27,5 ±39 ±55 i 87,5 i 140 ±220 ±35O ±550 i 0,875 ± 1,4 ±2,2 i3,5 ±5,5 i 8,75 ±14
2500 3150 ±13 +18 ±25 ±34 ±48 ±67,5 ±105 ±165 ±270 ±43O ±675 i 1,05 i 1,65 ±2,7 i4,3 i6,75 il0,5 i16,5
1) In order to avoid repetition of equal values, the table lists the values as "±x"; this is to be interpreted as es = +x and ei = -x, e.g. ~g:~ ~m.
2) The table gives the exact values derived from ± IT, either in micrometres or millimetres. For tolerance classes js7 to jsl1 (incl.), the values with decimal fractions of 0,5 ~m may possibly be
2
rJ)
rounded in national standards by replacing the exact value by the integer immediately below, e.g. ± 19,5 ~m may be rounded to ± 19 Ilm. o
3)
4)
Tolerance grades IT14 to IT16 (incl.) shall not be used for basic sizes less than or equal to 1 mmo
The values in the frame, for toJerance grades ITl to IT5 (incl.), for basic sizes greater than 500 mm and less than Or €Qual to 3 150 mm, are included for experimental use.
SI
N
I
l
~ !!!
ISO 286-2 : 1988 (El
Basic size j k
mm
Up to
Above and in- 5 ) 6 ) 71} 8 3 4 5 6 7 8 9 tO 11 12 13
cluding ' '
•
- 3 - 3 - 6 0 + 1 + 1 + 1 + 1 0 0 0 0 0 0
+ 5 + 9 +13 +4 + 8 +11 + 15 + 23 + 33 + 52 +84 + 130 + 210 + 330
18 30
- 4 - 4 - 8 0 + 2 + 2 + 2 + 2 0 0 0 0 0 0
+ 6 +11 +15 +4 + 9 +13 + 18 + 27 + 39 + 52 +100 + 160 + 250 + 390
30 50
- 5 - 5 -10 0 + 2 + 2 + 2 + 2 0 0 0 0 0 0
+ 6 +12 +18 +10 +15 + 21 +32 + 46 + 74 +120 + 190 + 300 + 460
50 80
- 7 - 7 -12 + 2 + 2 + 2 + 2 0 0 0 0 0 0
+ 6 +13 +20 +13 +18 + 25 +38 + 54 + 87 +140 + 220 + 350 + 540
80 120
- 9 - 9 -15 + 3 + 3 + 3 + 3 0 0 0 0 0 0
+ 7 +14 +22 +15 +21 +28 +43 + 63 +100 +160 + 250 + 400 + 630
120 180
-11 -11 -18 + 3 + 3 + 3 + 3 0 0 0 0 0 0
180 250
+ 7 +16 +25 +18 +24 +33 +50 + n +115 +185 + 290 + 460 + 720
-13 -13 -21 + 4 + 4 + 4 + 4 0 0 0 0 0 0
+ 7 +20 +27 +36 +56 + 81 +130 +210 + 320 + 520 + 810
250 315 ±16 ±26
-16 + 4 + 4 + 4 + 4 0 0 0 0 0 0
+ 7 +29 +22 +29 +40 + 61 + 89 +140 +230 + 360 + 570 + 890
315 400 ±18
-18 -28 + 4 + 4 + 4 + 4 0 0 0 0 0 0
+ 7 +31 +25 +32 +45 +68 + 97 +155 +250 + 400 + 630 + 970
400 500 ±20
-20 -32 + 5 + 5 + 5 + 5 0 0 0 0 0 0
500
630
800
630
800
1000
+44
0
+50
0
+56
0
+ 70
+00
0
+90
0
0
+ 110
+125
0
+140
0
0
+ 175
+200
0
+230
0
0
+280
0
+320
0
+360
0
+ 440
0
+ 500
0
+ 560
0
+ 700
0
+ 000
0
+ 900
0
+1100
0
+1250
0
+1400
0
•
+68 +105 +165 +250 +420 + 560 +1050 +1650
1000 1250
0 0 0 0 0 0 0 0
+ 78 +125 +195 +310 +500 + 700 +1250 +1950
1250 1600
0 0 0 0 0 0 0 0
+92 +150 +230 +370 +500 + 920 +1500 +2300
1600 2000
0 0 0 0 0 0 0 0
+110 +175 +280 +440 +700 +1100 +1750 +2000
2000 2500
0 0 0 0 0 0 0 0
+135 +210 +330 +540 +860 +1350 +2100 +3300
2500 3150
0 0 0 0 0 0 0 0
1) Where values for J5, 16 and J7 are shown as "±x", they are Identlcal wlth the tolerance class js5. js6 or js7 for that basic size step.
30
ISO 286-2 : 1988 (EI
Basic size
m n
mm
Up to
Above and in- 3 4 5 6 7 8 9 3 4 5 6 7 8 9
cluding
+ 5 +16 + 6 + 14 +18
- 3 + 4
+ 2 + 2
+ 6
+ 2
+
+
8
2
+ 12
+ 2 + 2
+27
+ 2 + 4
+ 7
+ 4
+ 8
+ 4
+ 10
+ 4 + 4 + 4
+29
+ 4
+ 6,5 + 8 + • + 12 + 16 +22 +34 +10,5 +12 +13 + 16 + 20 +26 +38
3 6
+ 4 + 4 + 4 + 4 + 4 + 4 + 4 + 8 + 8 + 8 + 8 + 8 + 8 + 8
+ 8,5 +10 +12 + 15 + 21 +28 +42 +12,5 +14 +16 +25 +32 +46
6 10 + "
+ 6 + 6 + 6 + 6 + 6 + 6 + 6 +10 +10 +10 + 10 + 10 +10 +10
+10 +12 +15 + 18 + 25 +34 +50 +15 +17 +20 +23 + 30 +39 +55
10 18
•
+ 7 + 7 + 7 + 7 + 7 + 7 + 7 +12 +12 +12 + 12 + 12 +12 +12
+12 +14 +17 + 21 +29 +41 +60 +1' +21 +24 + 28 +36 +48 +67
18 30
+ 8 + 8 + 8 + 8 + 8 + 8 + 8 +15 +15 +15 + 15 + 15 +15 +15
+13 +16 +20 +25 + 34 +48 +71 +21 +24 +28 +33 +42 +56 +79
30 50
+ • + •
+1'
+ •
+24
+
+ 30
• +
+ 41
• + • + • +17 +17
+28
+17
+33
+ 17
+39
+ 17
+ 50
+17 +17
50 80
+11 +11 + 11 + 11 +20 +20 +20 +20
+23 +28 +35 + 48 +33 +38 + 45 +58
80 120
+13 +13 + 13 + 13 +23 +23 + 23 + 23
+27 +33 +40 + 55 +39 +45 + 52 + 67
120 180
+15 +15 + 15 + 15 +27 +27 + 27 + 27
+31 +37 +46 + 63 +45 +51 +60 + 77
180 250
+17 +17 + 17 + 17 +31 +31 + 31 + 31
+36 +43 +52 + 72 +50 +57 +66 +86
250 315
+20 +20 +20 +20 +34 +34 +34 +34
+39 +46 + 57 + 78 +55 +62 + 73 + 94
315 400
+21 +21 + 21 + 21 +37 +37 + 37 + 37
+43 +50 + 63 + 86 +00 +67 + 80 +103
400 500
+23 +23 + 23 + 23 +40 +40 +40 +40
• 500
630
800
630
800
1000
+ 70
+26
+ 80
+ 30
+ 90
+34
+96
+ 26
+ 110
+ 30
+124
+ 34
+88
+44
+100
+50
+112
+ 56
+1'4
+44
+130
+ 50
+146
+ 56
31
ISO 286-2 : 1988 (EI
Basic siza
p
mm
Up ta
Above and in- 3 4 5 6 7 8 9 10
cluding
- 3 + 8
+ 6
+ 9
+ 6
+10
+ 6
+ 12
+ 6
+ 16
+ 6
+20
+ 6
+31
+ 6
+46
+ 6
+14,5 +16 +17 + 20 + 24 +30 +42 +60
3 6
+12 +12 +12 + 12 + 12 + 12 +12 + 12
+17,5 +19 +21 + 24 +30 + 37 +51 +73
6 10
+15 +15 +15 + 15 + 15 + 15 +15 + 15
+21 +23 +26 +29 +36 +45 +61 +88
10 la
•
+18 +18 +18 + 18 + 18 + 18 +18 + 18
+26 +28 +31 +35 +43 +55 +74 +106
la 30
+22 +22 +22 + 22 +22
+22 +22 +22
+30 +33 +37 + 42 + 51 +65 +88 +126
30 50
+26 +28 +26 + 26 + 26 +26 +26 +26
+40 +45 + 51 +62 +78
50 80
+32 +32 + 32 +32 +32
+47 +52 +59 +72 + 91
80 120
+37 +37 + 37 + 37 +37
500
630
800
630
800
1 ()()()
+122
+78
+138
+88
+156
+100
+146
+78
+168
+88
+190
+100
+ 1IlS
+78
+213
+88
+240
+100
•
1 ()()() +188 +225 +265
1250
+120 +120 +120
32
ISO 286-2: 1988 (E)
•
+23 + 23 + 23 +23 + 23 +23 +23 +23 +185 + 185 +185
+32 + 34 +'37 + 41 +49 + 61 +80 +112 +266 +300 +350
18 30 800 900
+28 +28 +28 +28 +28 +28 +28 +28 +210 +210 +210
•
180 200 2240 2500
+ n +n +n +n + n +460 +460 +460
+ 94 +100 +109 +126 +152 +685 +760 +880
200 225 2500 2800
+ 80 +80 +80 +80 +80 +550 +550 +550
33
ISO 286-2: 1988 IEl
Up to Up to
Above and in- 3 4 5 B 7 8 9 10 Above and in- B 7 8
cluding cluding
+ 350 390
- 3 +16
+14
+ 17
+ 14
+ lB
+ 14
+20
+ 14
+ 24
+ 14
+ 29
+ 14
+39
+ 14
+ 54
+ 14
500 560
+ 324
+ 280 + 280
+
+ 280
+21,5 +23 + 24 +27 + 31 +37 +4S + 87 + 354 + 390 + 420
3 6 560 630
+19 + 19 + 19 + 19 + 19 + 19 + 19 + 19 + 310 + 310 + 310
+25,5 +27 +29 + 32 +38 + 45 +59 + BI + 390 + 420 + 465
6 '0 630 7'0
+23 +23 +23 + 23 +23 + 23 +23 +23 + 340 + 340 + 340
+31 + 33 +38 + 39 +46 + 56 + 71 +98 + 430 + 460 + 505
'0 '8 7'0 800
•
+29 +29 +29 +29 +29 +29 +29 +29 + 390 + 390 + 390
+39 + 41 +44 +46 + 56 +88 + 87 + 119 + 46B + 520 + 870
'8 30 800 900
+35 +35 +35 +35 +35 +35 + 35 + 35 + 430 + 430 + 430
+47 + 50 +54 + 59 +88 +82 +100 +143 + 526 + 560 + 610
30 50 900 '000
+43 +43 +43 + 43 +43 +43 +43 +43 + 470 + 470 + 470
,SO +120 +126 +133 +146 +171 +208 + 1110 +1175 +1280
'80 2000 2240
+IM +IM +IM +IM +IM +IM +1000 +1000 +1000
+138 +142 +151 +188 +194 +237 + 1 210 +1275 +1390
•
'80 200 2240 2500
+122 +122 +122 +122 +122 +122 +1100 +1100 +1 100
34
ISO 286-2: 1988 IEl
- 3
+22
+ 18
+ 24
+ 18
+28
+ 18
+ 32
+ 18
+43
+ 18
500 560 + 444
+ 400
+ 470
+ 400
+ 644
+ 600
+ 670
+ 600
+ 710
+ 600
+ 28 + 31 + 35 + 41 +53 + 494 + 520 + 704 + 730 + 770
3 6 560 630
+ 23 + 23 + 23 +23 +23 + 450 + 450 + 660 + 660 + 660
+34 +:r1 + 43 + 50 +64 + 550 + 580 + 790 + 820 + 866
6 10 630 710
+28 +28 +28 + 28 +28 + 500 + 500 + 740 + 740 + 740
+ 41 +44 + 51 + 60 + 76 + 610 +640 + 890 + 920 + 965
10 18 710 800
+33 + 33 + 33 + 33 +33 + 580 + 560 + 940 + 940 + 940
+ 50 + 54 +62 + 74 +93 + 676 + 710 + 996 +'030 +' 090
24 800 900
+ 41 + 41 + 41 + 41 + 41 + 620 + 620 + 940 + 940 + 940
+50 + 54 + 62 + 74 + 57 + 61 + 69 + 81 +100 + 735 + no +1106 +1140 +1190
24 30 900 1000
+ 41 + 41 + 41 + 41 +48 + 48 +48 +48 +48 + 680 + 680 +'050 + 1 050 +'050
+59 +64 + 73 +87 + 71 + 76 + 85 +99 +122 + 846 + 885 +1216 +'255 +1315
30 40 1000 1 120
+48 +48 +48 +48 +60 +60 + 60 +60 +60 + 780 + 780 +1150 +1150 +1150
+65 +70 + 79 +93 + 81 + 86 + 95 +109 +132 + 906 + 945 +'366 +'405 +1465
40 50 1 120 1250
+ 54 +54 + 54 +54 +70 + 70 + 70 + 70 + 70 + 940 + 940 +'300 +'300 +1300
+79 +85 +96 +112 +100 +106 +117 +133 +161 +'038 +' 095 +'528 +1575 +'645
50 65 1250 1400
+66 +66 +66 +66 +87 +87 +87 +87 +87 + 960 +960 +'450 +1450 +1·450
65 80
+88 + 94 +106 +121 +115 +121 +132 +148 +176
1400 1600
+1128 +1175 +'678 +' ns +'795
+75 + 75 +75 +75 +102 +102 +'02 +102 +'02 +'050 +1050 +' 600 +'600 +'600
+'06 +113 +'26 +'45 +139 +'46 + '59 +178 +211 +1292 +1350 +1942 +2000 +2090
80 100 1600 1800
+ 9' + 9' + 91 + 9' +124 +124 + 124 +124 +124 +' 200 +1200 +1850 +'850 +1850
+ 119 +'26 +'39 +'59 +'59 +'66 +179 +'98 +231 +1442 +'500 +2092 +2150 +2230
100 120 1600 2000
+'04 +'04 +'04 +'04 +'44 +'44 +'44 +'44 +'44 +' 350 +' 350 +2000 +2000 +2000
+ '40 +147 +162 +'85 +'88 +195 +210 +233 +270 +1610 +1675 +2410 +2475 +2580
120 140 2000 2240
+'22 +122 +122 +'22 +170 +170 +170 +170 +170 +'500 +' 500 +2300 +2300 +2300
+ '62 +'59 +174 +197 +208 +215 +230 +253 +290 +1760 +1825 +2610 +2675 +2780
140 160 2240 2500
.-
+'34 +'34 +'34 +'34 +'90 +'90 +'90 +'90 +'90 +'650 +1550 +2500 +2500 +2500
+'64 +171 +'86 +209 +228 +235 +250 +273 +310 +2035 +2110 +3035 +3110 +3230
160 180 2500 2800
+'46 +'46 +'46 +'46 +210 +210 +210 +210 +210 +' 900 +'900 +2900 +2900 +2900
+'86 +'95 +212 +238 +256 +266 +282 +308 +351 +2235 +2310 +3335 +3410 +3530
200 2600 3150
+'66 +'66 +'66 +'66 +236 '+236 +238 +236 +236 +2100 +2100 +3200 +3200 +3200
+200 +209 +226 +252 +278 +287 +304 +330 +373
200 225
+'80 +180 +180 +'80 +256 +256 +258 +258 +258
+216 +225 +242 +268 +304 +313 +330 +356 +399
225 250
+'96 +'96 +'96 +'96 +284 +284 +284 +284 +284
+241 +250 +270 +299 +338 +347 +367 +396 +446
250 280
+218 +218 +218 +218 +315 +315 +315 +315 +315
400 450 +357 +370 +393 +427 +517 +530 +553 +587 +645
+330 +330 +330 +330 +490 +490 +490 +490 +490
+387 +400 +423 +457 +567 +580 +603 +637 +695
450 500
+350 +350 +350 +350 +540 +540 +540 +540 +540
1) Tolerance classes t5 to tB hncl.) have not been tabulated for baSIC SIZes less than or equal to 24 mmo It is recommended that tolerance classes u5 to uS
(jncl.) be used instead. However, if tolerance classes t5 to tB (incl.) are especially required, they may be calculated from the bases given in ISO 286-1. .
35
ISO 286-2 : 1988 (El
•
14 18 + 47 +50 + 67 + 66 +53 +56 +83 +72 +88 + 115
+ 39 +39 +39 + 39 +45 +45 +45 +45 + 45 + 45
+56 +60 +68 +60 +63 +67 +75 +67 +106 + 139 + 76 + 84 + 96 +115 + 147
18 24 + 47 +63
+ 47 + 47 + 47 +54 +54 +54 + 54 +54 + 54 + 63 + 63 + 63 + 83
80 100
+161 +168 + 181 +200 +193 +200 +213 +232 +265 + 318 + 238 + 249 +268
+146 +146 +146 +146 +178 +178 +178 +178 +178 + 178 + 214 + 214 + 214
+ 167 +194 +207 +226 +225 +232 +245 +254 +297 + 350 + 276 + 289 + 306
100 120 +172 + 210
+172 +172 +172 +210 +210 +210 +210 +210 + 254 + 254 + 254
+220 +227 +242 +265 +268 +273 +288 +311 +348 + 4al + 325 + 340 +363
120 140 +202 +248 +248 +248
+202 +202 +202 +248 +248 + 248 + 300 + 300 +300
+246 +253 +268 +291 +298 +305 +320 +343 +390 +440 + 365 + 380 +403
140 160 +228 +228 +280 +280 + 280 + 340
+228 +228 +280 +280 +280 + 340 + 340
160 180 +270 +w +292 +315 +328 +335 +350 +373 +410 + 470 +405 + 420 +443
.'
+262 +252 +252 +262 +310 +310 +310 +310 +310 + 310 + 380 + 380 + 380
+304 +313 +330 +356 +370 +379 +396 +422 +466 + 535 + 454 + 471 + 497
180 200 + 426
+254 +284 +284 +284 +350 +350 +350 +350 +350 + 350 + 426 + 426
200 225 +330 +339 +356 +382 +405 +414 +431 +467 +500 + 670 + 499 + 516 + 542
+310 +310 +310 +310 +395 +395 +385 +395 +395 + 395 + 470 + 470 + 470
+360 +369 +396 +412 +445 +454 +471 +497 +540 + 610 + 549 +566 + 692
225 250
+340 +340 +340 +340 +425 +425 +425 +425 +425 + 425 + 520 + 520 + 520
+4al +417 +437 +466 +498 +507 +527 +566 +605 + 685 + 612 +832 + 661
250 280 +395 +395 +395 +395 +475 +475 +475 +475 +475 + 475 + 580 +580 + 580
+448 +457 +4n +506 +548 +567 +677 +606 +656 + 735 + 682 + 702 + 731
280 315
+425 +425 +425 +425 +525 +625 +525 +625 +525 + 525 + 650 +650 + 650
+500 +511 +532 +564 +615 +626 +647 +679 +730 + 820 + 766 +767 + 819
315 365
+475 +475 +475 +475 +690 +690 +690 +690 +690 + 690 + 730 + 730 + 730
+556 +566 +587 +619 +685 +696 +717 +749 +800 + 890 + B56 +677 + 909
355 400 +530 +530 +530 +530 +660 +660 +660 +660 +660 + 660 + 820 + 820 + 820
+622 +635 +658 +692 +767 +780 +803 +937 +895 +990 + 960 + 963 +1017
400 450 +596 +596 +596 +596 +740 +740 +740 +740 +740 + 740 + 920 + 920 + 920
+687 +700 +723 +757 +847 +860 +883 +917 +975 +1070 +1040 +1063 +1007
450 500 +660 +820 +820 +820 +820 +1000 +1000 +1000
+660 +660 +660 +820 +820
1) Fundamental deviations v, x and y are not provided tor basic sizes greater than 500 mmo
2) Tolerance classes v5 to v8 (incl.) have not been tabulated for basic sizes less than or equal to 14 mmo It is recommended that tolerance classes x5
to x8 (incl.) be used instead. However, if tolerance classes v5 to va (incl.) are especially required, they may be calculated trom the bases given in
ISO 286-1.
31 Tolerance classes y6 to yl0 (incl.' have not been tabulated tor basic sizes less than or equal to 18 mmo It is recommended that tolerance classes z6
to z10 (incl.) ba used instead. However, it tolerance classes y6 to yl0 (incl.) are especially required, they may be calculated trom the bases given in
ISO 286-1.
36
ISO 286-2 : 1988 (E)
Basic slze
mm
• .a
Up to
Above and in- 6 7 8 9 10 11 6 7 8 9 10 11
cluding
- + 32 + 36 + 40 + 51 + 66 + 86 + 38 + 42 + 46 + 57 + 72 + 92
3 25 25 +
+ 25 + + 25 + 25 + 25 + 32 + 32 + 32 + 32 + 32 + 32
+ 43 + 47 + 53 + 65 + 83 + 110 + 50 + 54 + 60 + 72 + 00 + 117
3 6
+ 35 + 35 + 35 + 35 + 35 + 35 + 42 + 42 + 42 + 42 + 42 + 42
+ 51 + 57 + 64 + 78 + 100 + 132 + 61 + 57 + 74 + 86 + 110 + 142
6 '0 42
+ 42 + + 42 + 42 + 42 + 42 + 52 + 52 + 52 + 52 + 52 + 52
'4
+ 61 + 68 + n + 93 + 120 + 160 + 75 + 62 + 91 + 107 + 134 + 174
'0 + 50 + 50 + 50 + 50 + 50 + 50 + 64 + 64 + 64 + 64 + 64 + 64
• '4
'8
24
'8
24
30
+
+
+
+
+
+
101
71
60
86
73
es
+
+
+
+
+
+
109
78
60
94
73
es
+
+
+
+
+
+
106
121
57
60
73
es
+
+
+
+
+
+
103
60
125
73
140
es
+
+
+
+
+
+
130
157
73
172
60
es
+
+
+
+
+
+
170
60
203
218
73
es
+
+
+
+
+
+
es
n
111
98
131
118
+
+
+
+
+
+
119
139
118
95
n
98
+
+
+
+
+
+
104
131
98
151
118
n
+
+
+
+
+
+
120
150
170
118
n
98
+
+
+
+
+
+
147
n
162
98
202
118
+
+
+ 228
+ 98
+
+
187
248
118
n
40 + 128 + 137 + 151 + 174 + 212 + V2 + 164 + 173 + 187 + 210 + 248 + 306
30 112
+ 112 + + 112 + 112 + 112 + 112 + 148 + 148 + 148 + 148 + 148 + 148
+ 152 + 161 + 175 + 198 + 236 + 296 + 196 + 205 + 219 + 242 + 280 + 340
40 50
+ 136 + 136 + 136 + 136 + 136 + 136 + 180 + 180 + 180 + 180 + 180 + 180
+ 191 + 202 + 218 + 248 + 292 + 362 + 245 + 256 + Z72 + 300 + 346 + 416
50 65
+ 172 + 172 + 172 + 172 + 172 + 172 + 226 + 226 + 226 + 226 + 226 + 226
+ 229 + 240 + 256 + 284 + 330 + 400 + 293 + 304 + 320 + 348 + 394 + 464
65 80
+ 210 + 210 + 210 + 210 + 210 + 210 + V4 + V4 + V4 + V4 + V4 + V4
+ 280 + 293 + 312 + 345 + 398 + 478 + 357 + 370 + 389 + 422 + ·475 + 555
80 '00 + 258 + 258 + 258 + 258 + 258 + 258 + 335 + 335 + 335 + 335 + 335 + 335
+ 332 + 345 + 364 + 397 + 450 + 530 + 422 + 435 + 454 + 487 + 640 + 620
'00 '20 + 310 + 310 + 310 + 310 + 310 310 + 400 + 400 + 400 + 400 + 400 + 400
+
+ 390 + 405 + 428 + 465 + 525 + 615 + 496 + 510 + 533 + 570 + 630 + 720
'20 '40 + 365 + 365 + 365 + 365 + 365 + 365 + 470 + 470 + 470 + 470 + 470 + 470
+ 440 + 455 + 478 + 515 + 575 + 665 + 580 + 575 + 598 + 635 + 695 + 785
'40 '60
•
+ 415 + 415 + 415 + 415 + 415 + 415 + 535 + 535 + 535 + 535 + 535 + 535
+ 400 + 505 + 528 + 565 + B25 + 715 + B25 + 640 + 663 + 700 + 780 + 850
'60 '60 + 465 + 465 + 465 + 465 + 465 + 465 + 600 + 600 + 600 + 600 + 600 + 600
200 + 649 + 555 + 592 + 635 + 705 + 810 + 699 + 716 + 742 + 785 + 856 + 960
'60 + 520 + 520 + 520 + 520 + 520 + 520 + 570 + 570 + 570 + 570 + 570 + 570
+ 604 + 621 + 647 + 690 + 760 + 866 + 769 + 786 + 812 + 856 + 925 +1030
200 225
+ 575 + 575 + 575 + 575 + 575 + 575 + 740 + 740 + 740 + 740 + 740 + 740
225 250 + 669 + 686 + 712 + 755 + 825 + 930 + 849 + 866 + 892 + 935 +1005 + 1 110
+ 640 + 640 + 640 + 640 + 640 + 640 + B20 + B20 + B20 + B20 + B20 + B20
250 260 + 742 + 762 + 791 + 840 + 920 +1030 + 952 + 972 +1001 +1050 +1130 +1240
+ 710 + 710 + 710 + 710 + 710 + 710 + 920 + 920 + 920 + 920 + 920 + 920
+ B22 + 842 + 571 + 920 + 1000 +1 110 +1032 +1052 +1 <El +1130 +1210 +1320
260 3'5
+ 790 + 790 + 790 + 790 + 790 + 790 +1000 +1000 +1000 +1000 +1000 +1000
355 + 936 + 957 + 989 +1040 +'130 +1250 +1186 +1207 +1239 +1290 +1380 +1510
3'5 000 000 + 000 +1 150
+ + + 000 + 000 + 000 +1150 +1150 +1150 +1150 +1150
+1036 +1057 +1089 +1140 + 1230 +1360 +1336 +1357 +1389 +1440 +1530 +1660
355 400
+1000 +1000 +1000 +1000 + 1000 +1000 +1300 +1300 +1300 +1300 +1300 +1300
450 +1140 +1 163 +1197 +1255 +1350 +1500 +1400 +1513 +1547 +1605 +1700 +1850
400
+1100 +1 100 +1100 +1100 +1100 +1100 +1450 +1450 +1450 +1450 +1450 +1450
+1290 +1313 +1347 +1405 +1500 +1650 +1640 +1663 +1697 +1755 +1850 +2000
450 500
+1250 +1250 +1250 +1250 +1250 +1250 +1600 +1600 +1600 +1600 +1600 +1600
1) Fundamental deVIBtlons zand za are not provlded for baSIC SIZes greater than 500 mmo
ISO 286-2: 1988 (El
Basic siza
zb ze
mm
Up to
Above and in- 7 8 9 10 11 7 8 9 10 11
cluding
'4
18
24
'8
24
30
+
+
+
+
+
+
126
'00
157
138
181
160
+
+
+
+
+
+
135
100
169
136
193
160
+
+
+
+
+
+
'5'
100
188
136
212
160
+
+
+
+
+
+
178
100
220
136
244
160
+
+
+
+
+
+
218
100
265
136
290
160
+
+
+
+
+
1613
150
+ 200
188
239
218
+
+
+
+
+
+
In
150
221
1613
251
218
+
+
+
+
+
+
193
150
240
188
270
218
+
+
+
+
+
+
220
150
272
188
302
218
+
+
+
+
+
+
250
150
318
188
348
218
•
+ 225 + 239 + 262 + 300 + 360 +299 + 313 + 336 + 374 + 434
30 40
+ 200 + 200 + 200 + 200 + 200 + 274 + 274 + 274 + 274 + 274
+ 2IJI + 281 + 304 + 342 + 402 +350 + 364 + 387 + 425 + 485
40 50
+ 242 + 242 + 242 + 242 + 242 + 325 + 325 + 325 + 325 + 325
+ 330 + 348 + 374 + 420 + 490 +435 + 451 + 479 + 525 + 595
50 65
+ 300 + 300 + 300 + 300 + 300 +405 + 405 + 405 + 405 + 405
+ 390 +406 + 434 + 480 + 550 + 510 + 526 + 554 + 600 + IJIO
65 80
+ 360 +360 + 360 + 360 + 360 +480 +480 + 480 + 480 + 480
+ 480 + 499 +532 + 585 + 6115 +620 + 639 + lJI2 + 725 + 005
80 100
+ 445 + 445 + 445 + 445 + 445 +585 + 585 + 585 + 585 + 585
120 + 560 + 579 + 612 + 655 + 745 +725 + 744 + m + 830 + 910
'00 + 525 + 525 + 525 + 525 + 525 +690 + 690 + 690 + 690 + 690
120 140 + 61lO + 683 + 720 + 700 + IJIO + 840 + 863 + 900 + 960 +1050
+ 620 +620 +620 + 620 + 620 +800 +800 + 800 + 800 + 800
140 + 740 + 763 + 800 + B60 + 950 +940 + 963 +1000 +1060 +1 150
160
+ 700 + 700 + 700 + 700 + 700 +900 + 900 + 900 + 900 + 900
+ 820 + B43 + 880 + 940 +1030 +1040 + 1063 +1100 +1160 +'250
160 160
+ 700 + 700 + 700 + 700 + 780 +1000 +1000 +' 000 +'000 +1000
160 200 + 926 + 952 + 995 +1065 +1170 + 1196 +1222 +1255 +1335 +1440
+ 880 +880 +880 +880 + 880 +1150 +1150 +1150 + 1150 +1150
+1000 +1032 +1075 +1145 +1250 +1295 +1322 +1365 +1435 +1540
200 225
+ 960 + 960 +960 +960 + 960 +1250 +1250 +1250 +1250 +1250
+1096 +1122 +1166 +1235 + 1340 +1395 +1422 + 1455 + 1535 +1540
225 250
+1050 +1050 +1050 +1050 + 1050 +1350 +1350 +1350 +1350 +1350
+1252 +1281 +1330 +1410 +1520 +1602 +1631 + 1 61lO +1760 + 1 IJIO
250 280
+1200 +1200 + 1200 +1200 +1200 +1560 +1560 + 1550 +1550 +1560
280 +1352 +1381 +1430 +1510 +1620 +1752 +1781 +1830 + 1910 +2020
3'5 +1300 +1300 +1300 +1300 +1300 +1700 +1700 + 1700 +1700 +1700
+1557 +15B9 +1540 +1730 +1 B60 +1957 +19B9 +2040 +2130 +2260
3'5 355
+1500 +1500 +1500 +1500 +1500 +1900 +1900 +1900 +1900 +1900
355 + 1 7(fl +1739 +1790 +1880 +2010 +2157 +2189 +2240 +2330 +2460
400
+1650 +1650 +1650 +1650 +1650 +2100 +2100 +2100 +2100 +2 UlO
400 +1913 +1947 +2005 +2100 +2250 +2463 +2497 +2555 +2650 +2000
450
+1850 +1850 +1850 +1850 +1850 +2400 +2400 +2400 +2400 +2400
+2163 +2197 +2255 +2360 +2500 +26133 + 2 f1J7 +2756 +2850 +3000
450 500
+2100 +2100 +2100 +2100 +2100 +2600 +2600 +2600 +2600 +2600
1) Fundamental deviations zb and ze are not provided for basic sizes greater than 500 mmo
38
ISO 286-2 : 1988 (EI
Annex
For comparative purposes, the tolerance classes given in figures 6 and 7 illustrate the values for ES, EI and IT given tor the basic size
step trom 6 ta 10 mmo Where there are no tabulated values for th is basic size step, Le. those tolerance classes involving fundamental
deviations T, V and V, the values have been given, again for comparative purposes, for the basic size step from 24 to 30 mmo
For comparative purposes, the tolerance classes given in figures 8 and 9 iIIustrate the values for es, ei and IT given for. the basic size
step trom 6 to 10 mmo Where there are na tabulated values for this basic size step, Le. those tolerance classes involving fundamental
deviations t, v and y, the values have been given, again for comparative purposes, fpr the basic size step from 24 ta 30 mmo
39
ISO 286-2 : 1988 (EI
B CD o E EF F FG G H
+ 'JUU-l+1+
+ 40 o-+++-
+300
+ 200 -++++-++1-
•
+ 100 -t+t-HH-t++++
(concludedl
JS
~m
+ 100 ++H-tt-H-+++-
- 1DO -t+t-t++-t+rt+--
Figure 6 - Graphical review of toleranee classes for holes in terms of fundamental deviations
40
------------------------- - - - --
ISO 286-2 : 1988 (EI
+100
M
o ms ~I
Zero line
I
•-100
(concluded)
~
•
IT8 IT9 IT10 1T11
Ilm IN jG IN
la
+300
.200
+ 100
r-r-
o Zero line
N
-100
1111
Figure 7 - Graphical review of tolerance classes for holes in terms of standard tolerance grades 41
150286-2 : 1988 (EI
a b c cd d e ef f f h IS
Ilm
Zero line
o
EI. -
IIIIIII
II
-100
•
- 200
f.
- 300
-400
-500
. .
js k m n p r 5 t U V X z za zb
+ 100
o ~m. • • 1////
Zero line
-100
Figure 8 - Graphical review of tolerance classes for shafts in terms of fundamental deviations
42
ISO 286-2 : 1988 (E)
IT5 IT6 In
~m
d f 9 k _ js m psu x Id f 9 h . mpsux2 cd e f 9 il
k nrt v y z ,
e f g J k n r t v (d e f 9j knrtvy dfghjs j
mpsu xz
+ 100
lM
•• •• •
o o· I
~Oill
• ••
••
•
• -100
+ 100
~
III
Zero line
0
• 100 -
200
'A
JV
400
Figure 9 - Graphical review of toleranee classes for shafts in terms of standard toleranee grades
43
ISO 286-2 : 1988 (E)
UDC 621.753.1/.2
Descriptors: dimensional tolerances, fits, standard tolerances, dimensions.