Professional Documents
Culture Documents
X-431 PADII: Launch
X-431 PADII: Launch
Reset Button
X-431 PADII Professional Tablet (To connect to an (To provide power to the
(To connect the
external projector or non-16pin connector diagnostic connector
monitor with HDMI through connection to
for extension purpose.)
*Note1: interface.) the vehicle’s battery.)
USB Port is reserved for add-on Camera Flash
modules, and other USB devices use OBDI Converter Password Envelope Non-16pin Connector
only. Handgrip
Micro USB Port is reserved for Micro
USB cable only.
Rear Camera
(Optional)
(For detailed non-16pin
*Note2: It illuminates red while
(A converting cable (A piece of paper bearing connectors, please check
X-431 PADII tablet is charging. Product S/N and Register the package)
for connecting
Once charging is finished, it will Audio Speakers non-16pin connector.) Password, which is
turn green. required for your
registration.)
Rear View
Pictures illustrated here are for reference purpose only and this Quick Start Guide is subject to change without notice.
X-431 PADII Quick Start Guide (EN) LAUNCH
Diagnostic Connector Note: Remember to remove the 1. Charge X-431 PADII Tablet
diagnostic connector from the DLC
OBD II 16 PIN connector if it keeps unattended. Except that power adaptor supplies power to X-431 PADII, X-431
PADII can also obtain power from the Lithium polymer battery.
Choose any of the followings to charge X-431 PADII tablet:
1. Use the included 5V power adaptor: Connect one end of the
power adaptor to DC IN port of X-431 PADII, then connect the
Communication indicator other end to the AC outlet. We assume no responsibility for
damage or loss resulting from using other similar adaptors other
Power indicator than the specified one.
2. Use the docking station: Follow the steps described as below to
Micro USB port NEAR CENTER charge your X-431 PADII tablet:
OF DASH DLC Location
Install diagnostic connector 1
1. Locate vehicle’s DLC socket: It provides standard 16 pins and is generally located on driver’s side, about 12 inch away Locate the charging slot on the bottom of X-431 PADII tablet and
from the center of dashboard. See Figure DLC Location. If DLC is not equipped under dashboard, a label indicating the docking station. See Fig. a & Fig. b.
its position will be given. In case no DLC is found, please refer to Automobile Repair Manual;
2. Plug the connector into the vehicle's DLC(It is suggested to use the OBD II extension cable to connect the DLC and the
connector). For vehicles with non-16PIN DLC, please choose the desired connector. Normally the power indicator of
diagnostic connector will light up.
g
k in n Fig. a Fig. b
c io *Note3: It is designed to charge the display tablet. For *Note5: Plug the diagnostic connector into
Do tat details on how to charge, please refer to Section “Charge the socket for demo experience when the
S X-431 PADII Tablet” on the right. station is connected to the AC outlet. 2
Align the charging slots, and then dock the tablet into the station
3
to ensure that it firmly sits on the docking station. Refer to Fig. c.
Charging Slot Insert one end of power cord of the docking station into the power
OBD 16 Socket with
jack, then plug the other end into the AC outlet.
power output 5
Power Interface
(Provides power to Fig. c
*Note4: These 2 sockets are used to the docking station)
store the additional DBScar/EasyDiag/
golo diagnostic connector (separately Note: If X-431 PADII tablet keeps idle or unattended for a long
purchased). period, please lock the screen or turn it off to save power.
Pictures illustrated here are for reference purpose only and this Quick Start Guide is subject to change without notice.
X-431 PADII Quick Start Guide (EN) LAUNCH
2. Connections 3. Power on, Wi-Fi connection, Register and Download software
To Vehicle’s DLC
B C
Login Interface Create an Account
B Via Battery Clamps Cable
(To be continued...)
X-431 PADII Quick Start Guide (EN) LAUNCH
3. Power on, Wi-Fi connection, Register and Download software (Cont.) 4. How to Diagnose
D Tap “Diagnostic”
Activate Connector
Activate
Where is my activation code?
No connector? Yes
E …… (Refer to
Finish Register Select vehicle
Section 3)
Tap here to enter
update center
Activation
Code Register & Activate Select diagnostic
OK software version
F
Select test function Select test system
G
4. Download & Update Software Diagnosing Flowchart
Tap to start downloading.
Note: By default, all vehicle software are selected. To deselect Notes:
certain software, just uncheck the box next to the software * 1. To start diagnosing a vehicle, you have to register the diagnostic
version. connector. For details, please refer to Section 3 “Power on, Wi-
Once downloading finished, the software packages will be Fi connection, Register and Download Software” in this
installed automatically. Quick Start Guide.
* 2. To perform update, tap and select “Update” from the pull-
down list.
For more detailed operations, please refer to User’s Manual of X-431 PADII.