The document provides a troubleshooting list for an elevator controller (MPK708A). It lists 28 possible fault codes (E1 through E28), whether the fault will display on the floor indicator, how it is logged (registered) in the computer memory, and recommended renewal or repair methods. The controller can store up to 50 instances of fault logging to aid in failure prediction and maintenance.
The document provides a troubleshooting list for an elevator controller (MPK708A). It lists 28 possible fault codes (E1 through E28), whether the fault will display on the floor indicator, how it is logged (registered) in the computer memory, and recommended renewal or repair methods. The controller can store up to 50 instances of fault logging to aid in failure prediction and maintenance.
The document provides a troubleshooting list for an elevator controller (MPK708A). It lists 28 possible fault codes (E1 through E28), whether the fault will display on the floor indicator, how it is logged (registered) in the computer memory, and recommended renewal or repair methods. The controller can store up to 50 instances of fault logging to aid in failure prediction and maintenance.
In case of failure occurring or working under irregular
conditions during the time of elevator’s running, the commissioning personne can conduct the failure predication by the means of the failure logging of main controller 、inverter. MPK708Acan store 50 pieces of failure logging. No.of whether the floor Connect Method of renew fault display the failure yes,computer Security circuit turn to E1 Security circuit opened register the failure. gight yes,computer Door Lock error Or over time Door Lock closed register the failure. E2 Door Lock open , elevator yes,computer Door Lock closed stop register the failure. Cannot detect the door zone No ,register the Only register,not E3 signal or crawl time over(10s). failure treat with Can’t Find the Deceleration Point ( run time yes,computer Level floor renew after E4 over“Floor protect”menu register the failure. door opened time limit) yes,computer Up Limited Switch E5 Up Limited Switch Opened register the failure. renew. yes,computer Down Limited Switch E6 DownLimited Switch Opened register the failure. renew. No ,register the E7 Deceleration Switch Error Slow leveling floor failure yes,computer E8 Contact Not Release Release the point register the failure. Taco Direction Error or yes,computer Level floor renew after E9 impulse error. register the failure. door opened yes,computer E10 Brake Error Check or power off register the failure. yes,computer E11 Run Time Error Check or power off register the failure. yes,computer Connect the monitor E12 Inverter Error register the failure. and control] point E13 Door Contact not Release yes,computer Check or door lock No.of whether the floor Connect Method of renew fault display the failure register the failure. close After leveldown run No ,register the E14 take count ofimpulse error to lower base station failure revise The number of impulse and No ,register the E15 Do not treat with inductor is not same failure In the condition of E22the signal E16 / / of terminal station wrong. The lock of car door closed E17 over 2s , which of landing door / / is no response. Start up over 5Scan notcheck yes,computer E18 Check or power off the input point oftransducer. register the failure. The input point of transducer yes,computer E19 Input point turn right. closed register the failure. Switch opened the elevator is No ,register the E20 / not at terminal station failure Elevator stop yes,computer E21 Switch resleased ,switchofbrakeis closed. register the failure. No ,register the Elevator is at terminal station , Elevator turn to E22 failure, turn to down speed change switch closed down terminal station terminal station Button locked and the time E23 / / over 30s The door lock closed over 3S, and the switch of close door final limit is not open, the computer will register the Start up inspection or failure E24, the outer calling the door lock open and inner selection displayt E24 yes,computer E24 over 2S,or the final at the sametime ,the door will register the failure. limit of close door open in the opposite open . direction .If there is not 2# door operator , the input point of close door final limit should not be connected. E25 There is pre-open door yes,computer Detect the input point function , if the PM708 register the failure. of door zone or start up enlargement board can not inspection . detect the input point of door No.of whether the floor Connect Method of renew fault display the failure zone. Detect the PM708 There is pre-open door enlargement board or function , if the PM708 yes,computer E26 start up inspection or enlargement board can not be register the failure. cancel the test function detected of enlargement board There is pre-open door function , if the PM708 yes,computer E27 enlargement board can not Start up inspection register the failure. detect the input of safety touching point, the lift stop. There is pre-open door function , if the PM708 enlargement board can not detect the input of speed test, / E28 the door will not open when the lift arrive the appointed stop and the open door button can not work.