Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

TECHNICAL DATA SHEET

Surface-Applied Cementitious waterproofing


1 of 4

Krystol T1® Waterproofing System


DESCRIPTION
Krystol T1® is a surface-applied crystalline waterproofing treatment for concrete structures that is used to protect
against the ingress of water. It is a dry powder, which when mixed with water becomes a coating that is applied to the
inner or outer side of a concrete structure. Krystol T1® may also be applied as a dry-shake to freshly poured concrete.

Krystol T1® contain Kryton’s unique and proven Krystol® technology which reacts with un-hydrated cement particles to
grow millions of needle-like crystals deep into the concrete mass. Over a period of weeks and months, these crystals
grow, filling the naturally occurring pores and voids in concrete, and permanently blocking the pathways for water and
waterborne contaminants. Later, if cracks form due to settling or shrinkage, incoming water triggers the crystallization
process and additional crystals begin to grow, filling cracks and ensuring that the structure’s waterproofing barrier is
maintained and protected. The concrete itself becomes the waterproof layer removing the need for any surface
treatment.

FEATURES
l Replaces unreliable exterior membranes, liners and coatings
l Reaches well below the surface and is not affected by surface wear or abrasion
l Self-seals hairline cracks up to 0.5 mm (0.02 inches)
l Reactivates in the presence of moisture
l Waterproofs from any side (i.e. positive or negative side)
l Treatment may be applied to old or new concrete
l Safe for contact with potable water, certified by NSF to NSF/ANSI Standard 61
Drinking Water System Components - Health Effects

KEY BENEFITS

l Lowers the cost of waterproofing


l Permanently waterproofs the concrete
l Increases reliability and quality control
l Increased durability decreases building maintenance and repair costs
l Protects against corrosion
l Superior performance

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Surface-Applied Cementitious waterproofing
2 of 4

RECOMMENDED USES

l For concrete foundations, walls and slabs on grade


l Construction Joints
l Elevator pits and equipment pits
l Parking structures
l Swimming pools and water features
l Water towers, reservoirs and storage tanks
l Tunnels, pipes and underground vaults
l Water treatment reservoirs
l Bridge decks, elevated slabs and ramps
l Rooftops and roof decks

PHYSICAL PROPERTIES
Appearance Gray powder

Bulk density g/cm 3 (lb. /cu. ft.) 1.36 (85)

pH (when mixed with water) 13

PLASTIC PROPERTIES

Working Time (20°C/ 68°F, 50% RH) 60 minutes with continued stirring (slurry)
30 minutes (dry-pack)

Hardening Time (20°C/ 68°F, 50% RH) 5 hours (slurry)


3 hours (dry-pack)

HARDENED PROPERTIES

Hydrostatic head resistance 140 m (460 ft.)

Typical Rate of Crystal penetration 2mm (0.08 inches) per week

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Surface-Applied Cementitious waterproofing
3 of 4

APPLICATION
l Surface Preparation
Surface must be clean and have an ‘open capillary surface’. Remove laitance, dirt, grease etc. by means of high
pressure water jetting, wet sandblasting or use of hard bristle brush. Concrete slab with crack, construction joints,
honey combing etc. must be treated with Kryton products before pre-watering the surface. Krystol T1® slurry to be
applied on damp surface with no wet sheen

l Dry-shake broadcast
Spread Krystol T1® on freshly-poured horizontal slabs before final trowelling and finishing at a coverage
of 1.0 kg/m2.

l Horizontal Surfaces
Single Coat - Mix Krystol T1® to a slurry consistency (5 parts powder to 2 part clean water). Apply with a natural
bristle concrete brush using an aggressive circular motion to coat the concrete with the Krystol T1® mix at a rate of
1.0 Kg/m2.
Double coat (Krystol T2®) Mix Krystol T1® to a slurry consistency (5 parts powder to 2 part clean water). Apply
with a natural bristle concrete brush using an aggressive circular motion to coat the concrete with the Krystol T1®
mix at a coverage of 0.8 kg/m2. After 4-6 hours of Krystol T1® application, mix Krystol T2® to slurry consistency (5
parts powder to 2 parts of clean water) and apply Krystol T2® slurry over Krystol T1® at the rate of 0.8 kg/m2 with a
natural bristle concrete brush.

l Vertical Surfaces (+ve side)


Single Coat - Mix Krystol T1® to a slurry consistency (5 parts powder to 2 part clean water). Apply with a natural
bristle concrete brush using an aggressive circular motion to coat the concrete with the Krystol T1®. mix at a rate of
1.0 kg/m2.

l Vertical Surfaces (-ve side) - (Krystol T2®) Mix Krystol T1® to a slurry consistency (5 parts powder to 2 part clean
water). Apply with a natural bristle concrete brush using an aggressive circular motion to coat the concrete with
®. 2
the Krystol T1 mix at a coverage of 0.8 kg/m .

l Constructions Joints (+ve sides)


Mix Krystol T1® to putty consistency (5 parts powder to 1 part clean water) and apply at the rate of 0.25 kg/mtr
approx. for 10 mm & subsequent layer of 10 mm with Krystol Bari-CoteTM at the 0.25 kg/mtr in a groove of 15
mmX20 mm

l Tie Rod Treatment


Mix Krystol T1® to putty consistency (5 parts powder to 1 part clean water) and apply at the rate 0.05 kg/point. and
subsequent layer with Krystol Bari-CoteTM at the 0.05 kg/point approximately in a groove of 10 mm

Please contact a Kryton representative for details.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Surface-Applied Cementitious waterproofing
4 of 4

l Post Treatment Care


Completed application should be protected against direct exposure to sun for 48 hours and against rain and light
traffic for 12 hours. Heavy traffic should be avoided until the surface has hardened (at least 5 days). The treated
concrete surface should not be permanently exposed to liquids for 7 days. Finishes containing Portland cement
may be applied over Krystol T1® after 3 hours and other can be applied after 7 days. For using Krystol T1® as part
of a crack repair system, please refer to Kryton’s Krystol Crack Repair System. For using Krystol T1® as part of a
construction joint system, please refer to Kryton’s Construction Joint System.

Note: Application should not be made when the surface temperature is below 5ºC (41ºF).

LIMITATIONS

Krystol T1® . is an effective waterproofing system for rigid concrete structures only and may not reliably seal cracks
and joints that experience constant or repeated movement. However is effective on surface with minor movement as
experienced on Balconies, terraces which takes normal load. Consult a Kryton representative for project specific
recommendations. Krystol T1® is not a decorative coating.

SAFETY

For professional use only. This product becomes extremely caustic when mixed with water or perspiration. Avoid
contact with skin or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious gloves.

PACKAGING
l 25 kg resalable pail

SHELF LIFE
Krystol T1® has a shelf life of 2 years unopened pails when stored under standard conditions and minimum
temperature of 7OC.

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. (A unit of Kryton, Canada) warrants that its products are free from manufacturer’s
defects and, when applied in accordance with the current specifications and application instructions will perform as
stated in its product literature. Because methods and conditions of use are beyond the control of Kryton, no
guarantee, expressed or implied can be given as to the results of application. Liability of Kryton shall be limited to
replacement of materials proved defective or, at its option, refund of the purchase price of the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
(Surface-Applied Cementitious Concrete Waterproofing)
1 of 4

®
Krystol T2 Waterproofing System
DESCRIPTION
Krystol T2® system is a surface-applied crystalline waterproofing treatment for concrete structures that is used to
protect against the ingress of water. It is a dry powder, that when mixed with water becomes a coating that is
applied to the inner or outer surface of the concrete structure. Krystol T2® can be used in conjunction with Krystol
T1® as a second coat or individually as a dry-shake broadcast to fresh concrete, or for coating on existing concrete
surfaces.

Krystol T2® contains Kryton’s unique and proven Krystol® technology which reacts with un-hydrated cement
particles to form millions of needle-like crystals. These crystals grow in a catalytic reaction, filling the naturally
occurring pores and voids in concrete, and permanently blocking the pathways for water and waterborne
contaminants. Later, if cracks form due to settling or shrinkage, incoming water triggers the crystallization process
and additional crystals form, filling cracks and ensuring that the structure’s waterproofing barrier is maintained and
protected. The concrete itself becomes the waterproof layer removing the need for any surface treatment.

FEATURE
l Replaces unreliable exterior membranes, liners and coatings
l Reaches well below the surface and is not affected by surface wear or abrasion
l Self-seals hairline cracks up to 0.5 mm (0.02 inches)
l Reactivates in the presence of moisture
l Waterproofs from any direction (i.e. positive or negative side)
l Treatment may be applied to old or new concrete
l Safe for contact with potable water, certified by NSF to NSF/ANSI Standard 61
Drinking Water System Components-Health Effects

KEY BENEFITS
l Increases reliability and quality control
l Lowers the cost of waterproofing
l Increased durability decreases building maintenance and repair costs
l Protects against corrosion
l Good performance

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
(Surface-Applied Cementitious Concrete Waterproofing)
2 of 4

RECOMMENDED USES

l As a second coat over Krystol T1®


l For concrete foundations, walls and slabs on grade
l Elevator pits and equipment pits
l Parking structures
l Swimming pools and water features
l Water towers, reservoirs, storage tanks and water treatment reservoirs
l Rooftops and roof decks

PHYSICAL PROPERTIES

Appearance Gray powder

Bulk density g/cm 3 (lb. /cu. ft.) 1.40 (87)

pH (when mixed with water) 13

PLASTIC PROPERTIES

Working Time (20°C/ 68°F, 50% RH) 60 minutes with continued stirring (slurry)
30 minutes (dry-pack)

Hardening Time (20°C/ 68°F, 50% RH) 4 hours (slurry)

HARDENED PROPERTIES

Hydrostatic head resistance 140 m (460 ft.)

Typical rate of crystallisation 2mm (0.08 inches) per week

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
(Surface-Applied Cementitious Concrete Waterproofing)
3 of 4

APPLICATION
l Coating as Slurry with Krystol T1®
When applying Krystol T2® as a slurry-based coating on concrete, mix Krystol T2® to a slurry
consistency (5 parts powder to 2 parts clean water) and with a natural bristle concrete brush, use an
aggressive circular motion to coat the concrete with the Krystol T2® mix at a coverage of 0.8 Kg/m2
when used with Krystol T1® as a second coat.

l Dry-shake
When applying Krystol T2 as dry-shake broadcast to freshly-poured horizontal slabs, spread Krystol
T2® on the fresh concrete before final trowelling and finishing at a coverage of 1.0 kg/ sqm (1.8 lb./sq.
yd.). Please contact a Kryton representative for details. Completed application should be protected
against direct exposure to sun for 48 hours and against rain and light traffic for 12 hours. Heavy traffic
should be avoided until the surface has hardened (at least 5 days). The treated concrete surface
should not be permanently exposed to liquids for 7 days. Finishes containing Portland cement may be
applied over Krystol T2® after 3 hours but other finishes should not be applied before 28 days.

Note: Application should not be made when the surface temperature is below 5ºC (41ºF).

LIMITATIONS
Krystol T2® is an effective waterproofing system for rigid concrete structures only and may not reliably seal
cracks and joints that experience constant or repeated movement. However is effective on surfaces with
minor movement as experienced on Balconies, Terrace which takes normal load. Consult a Kryton
representative for project specific recommendations. Krystol T2® is not a decorative coating.

SAFETY
For professional use only. This product becomes extremely caustic when mixed with water or perspiration.
Avoid contact with skin or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious
gloves.

PACKAGING
l 25 kg resalable pails
.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
(Surface-Applied Cementitious Concrete Waterproofing)
4 of 4

SHELF LIFE
Krystol T2® has a shelf life of 24 months for unopened pails. When stored under standard conditions and
minimum temperatures of 70 C

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. (A unit of Kryton, Canada) warrants that its products are free from manufacturer’s
defects and, when applied in accordance with the current specifications and application instructions will perform
as stated in its product literature. Because methods and conditions of use are beyond the control of Kryton, no
guarantee, expressed or implied can be given as to the results of application. Liability of Kryton shall be limited
to replacement of materials proved defective or, at its option, refund of the purchase price of the product

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
Specification
KIM (Krystol Internal Membrane)
WATERPROOFING WITH KIM - ADMIXTURE

Item of work Qty. Unit Rate Amount


Providing of Cementitious crystallisation based
concrete waterproofing admixture KIM (Krystol
Internal Membrane) @0.8% by weight of cement.
This rate may vary from 0.8%-2% depending on
site requirement and minimum cement content.
The KIM admixture to be mixed for 5-7 minutes
after mixing of cement, sand, aggregate and
water.

SPECIFICATION
KIM (Krystol Internal Membrane) admixture a cementitious dry powder to be added in designed
concrete @0.8% by weight of cement. This rate may vary from 0.8%-2% depending on site
requirement and minimum cement content. The admixture does not contain, stearates, sodium
or silicate. It is not hydrophobic or surface densifier, will be able to withstand high hydrostatic
pressure and does not require any protection coating. It will become a real integral part of
concrete.

PROCEDURE:
All the ingredients of the concrete as per design are to be mixed then KIM admixture to be
added in the mixed concrete) @0.8% by weight of cement. This rate may vary from 0.8%-
2% depending on site requirement and minimum cement content (1 kg per 50 kg bag of
cement). Incase RMC is being used KIM should added @6 kg / cum of concrete. KIM
should be added gradually in pan mixture / transit mixture while it is rotating for 5-7
minutes so that KIM admixture is thoroughly mixed. After that concrete should be laid as
normal one with vibration / compaction and cured as per concrete specification.

For any construction joints treatment a U – shaped groove should be made of 10mm wide
and 15-20mm deep. This should be filled up with Krystol T1 putty consistency 5:1 (5parts
of T1 to 1 part of water) and Krystol Baricote in 3.5:1 (3.5 part of Baricote to 1 part of
water) as per manufacturer’s specification
ADVANTAGES OVER THE CONVENTIONAL SYSTEMS & FEATURES OF KIM
1. Facilitates faster back filling – saving time & money. KIM concrete can be poured
directly over the P.C.C. and the cost of overlaying systems like coatings over the P.C.C.
shall be eliminated.
2. Eliminates the need for costly waterproofing membranes, liners or coatings.
3. Protects reinforcing steel from corrosion
4. Reduces shrinkage & cracking.
5. Self – heals any hairline cracks that may occur from subsequent shrinkage or settling.
6. Eliminates the risk of costly repairs and damage.
7. Non-toxic and safe for drinking water tank.
8. Provides excellent resistance to waterborne chemicals such as sulphates and chlorides.
9. Facilitates unique design options and utilization of greater property area.

TYPICAL APPLICATIONS
1. Foundations, raft, retaining wall of basement
2. Water tank, Sewage Tank Structures
3. Bridges, Parking Structures, Tunnels, Pipe Lines etc.
4. Pools, Aquarium & Other Water Features
5. Architectural Concrete, Precast Concrete
6. Compatible with fiber – reinforced
7. Compatible with admixtures as water reducers & super plasticizers.
TECHNICAL DATA SHEET
Concrete Waterproofing Admixture
1 of 4

Krystol Internal Membrane™ (KIM®)


DESCRIPTION
Krystol Internal MembraneTM (KIM®) is a hydrophillic crystalline waterproofing admixture in dry powdered form, effective
in creating waterproof concrete. KIM is the STANDARD used for qualifying Permeability Reducing Admixture -
Hydrostatic Conditions as specified by ‘ACI 212’ (Highest Grade of Permeability Reducing Admixture). KIM is used in
place of externally applied surface membranes to protect against moisture transmission, chemical attack and corrosion
of reinforcing steel.

KIM admixture consists of portland cement, quartz, sand and propriety chemicals, but does not contain sterates and
sodium-silicates. When combined with fresh concrete, Kryton’s unique and proven Krystol technology reacts with un-
hydrated cement particles to form millions of needle-like crystals. These crystals grow in a catalytic reaction, filling the
naturally occurring pores and voids in concrete, and permanently blocking the pathways for water and waterborne
contaminants. Later, if cracks form due to settling or shrinkage, incoming water triggers the crystallization process and
additional crystals form, filling cracks and ensuring that the structure’s waterproofing barrier is maintained and
protected.

In addition to filling the pores and capillaries of the concrete matrix with crystals, KIM enhances the natural hydration
process by intensifying and prolonging the hydration of the cementing materials. This reduces the size and number of
capillary pores within the concrete matrix, making it dramatically less porous, and improving strength and
durability characteristics.

FEATURES

Ÿ KIM is the STANDARD for Permeability Reducing Admixture - Hydrostatic Conditions as Specified by
‘ACI212’
Ÿ ONLY Crystalline Waterproofing Admixture with BIS Certification for use in India
Ÿ Reduces Chemical Attack by deleterious materials
Ÿ Significantly decreases Corrosion of Steel in the RCC
Ÿ Replaces unreliable exterior membranes, liners and coatings
Ÿ Added directly to ready-mix truck or at batch plant, no mixing with water or additional step of premix
with water required
Ÿ Self-seals hairline cracks up to 0.5 mm (0.02 inches) - Best in Industry
Ÿ Reactivates in the presence of moisture
Ÿ Effective against hydrostatic pressure up to 140 m (460 ft.) of head pressure - Best in Industry
Ÿ Waterproofs from any direction (i.e. positive or negative side)
Ÿ Impervious to physical damage and deterioration
Ÿ Safe for contact with potable water, certified by NSF/ANSI Standard 61 Drinking Water System
Components Health Effects
Ÿ Significantly reduces permeability and concrete shrinkage and cracking - Best in Industry
Ÿ Provides excellent resistance to waterborne chemicals such as sulfates, chlorides & acids
Ÿ Compatible with self-compacting concrete (SCC)

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Concrete Waterproofing Admixture
2 of 4

KEY BENEFITS

l Increases durability of concrete


l Increases reliability and quality control
l Shaves weeks off the construction schedule
l Reduces the cost of maintenance and repair
l Excellent performance

RECOMMENDED USES

KIM is ideal for permanent protection for all concrete that will be subject to water pressure, such as:

l Below grade parking structures, basements, elevator pits and foundations of high-rise towers
l Recreational facilities such as aquatic centers, aquariums, zoos, water parks and marinas
l Architectural water features such as fountains and waterfalls
l Water containment reservoirs, water treatment tanks, sewage tanks, manholes, traffic tunnels, below grade
pipelines and subway tunnels, marine structures
l Bridges, dams and highway infrastructure
l Concrete homes including basements, foundations, swimming pools, decks, bathrooms, garages and exteriors
l Properly designed roof tops and plaza decks
l Shotcreting

PHYSICAL PROPERTIES
Appearance Gray Powder
3
Bulk Density g/cm (lb./cu. ft) ~1.35 (88)
Specific Gravity ~2.6

PLASTIC PROPERTIES
KIM typically delays the setting time of the concrete. Consult a Kryton Representative to ensure proper compatibility with
concrete admixtures. It can be used for most common applications and is compatible with common admixtures such as
plasticizers, accelerators, retarders and air-entrainers.

WORKABILITY
ASTM C143 -Standard Test Method for Slump of Hydraulic Cement Concrete.

KIM enhances the workability and plastic properties of concrete in many ways. KIM Provides a plasticizing effect at low
and high slumps. KIM works very well with superplasticizers to achieve high slumps for long pumping distances without
segregation.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: custcare@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Concrete Waterproofing Admixture
3 of 4

HARDENED PROPERTIES
Hardened Properties Test Reference KIM Performance
Coeffcient of Water Permeability Taywood/Valenta/
DIN 1048-PtV Reduced 70 - 90%
Drying Shrinkage BS 1881-5 Reduced 25%
Freeze/Thaw Expansion ` BS 5075-2 Reduced 87%
Compressive Strength (28 Days) BS EN 12390-3 Increased 8%
Flexural Strength (28 Days) BS EN 12390-5 Increased 7%
Modulus of Elasticity BS 1881-122 Increased 16%

British Board of Agreement (2005), Certificate No 05/4217


KIM-HS is marketed in India as KIM

DOSAGE
l 0.8% by weight of cement. This rate may vary from 0.8% - 2% depending on site requirements and minimum
cement content
l Please consult a Kryton Representative to determine recommended dosage rate. Trial tests are required to
determine actual plastic properties.

APPLICATION
KIM can be mixed directly into wet concrete in the dry powdered form it does not require be pre-wetting or mixing into
slurry prior to adding to Ready Mix Concrete. The dry application ensures that your w/c ratio in concrete is maintained
and the durability and strength gain are as designed.

l Central Mixer
KIM can be added either directly to the central mixer in the plant. A mixing time of 2-3 minutes should be sufficient
depending on mix speed. The concrete then should be transferred to the pore location and poured in accordance
with BIS or ACI requirements. Proper curing is essential to achieve the performance and benefits of KIM. Cure in
accordance with ACI 308.1 guidelines.
l
l Transit Mixer
KIM can be added directly in to the drum of a transit mixer after it reaches the site. A mixing time of 2-3 minutes
should be sufficient depending on mix speed. The concrete then should be transferred to the pore location and
poured in accordance with BIS or ACI requirements. Proper curing is essential to achieve the performance and
benefits of KIM. Cure in accordance with ACI 308.1 guidelines.
l
l Pre-Cast Batch Plant
KIM should be admixed @ 0.8%-2% in the mixer after mixing of standard aggregates.
l
l Application Temperature - During mixing ambient temperature should be in the range of 100 C to 270 C

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Concrete Waterproofing Admixture
4 of 4

LIMITATIONS
KIM is an effective waterproofing system for rigid concrete structures and may not reliably seal cracks and joints
experiencing variable loading or repeated movement. For terraces experiencing light loads, KIM combined with
Kryton Joint System is an acceptable application. Please consult a Kryton Representative for the Krystol®
waterproofing system that best suits your project. In applications that have variable loading and repeating
movement KIM may be used as a secondary waterproofing system.

SAFETY
For professional use only. This product becomes caustic when mixed with water or perspiration. Avoid
contact with skin or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious
gloves.

PACKAGING
l 25 kg resealable pails
l 20 kg bags

SHELF LIFE
l KIM has a shelf life of 2 years for unopened pails
l 12 months for Dry Bags when stored under standard conditions and minimum temperature of 70 C

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. warrants that its products are free from manufacturer’s defects and, when
applied in accordance with the current specifications and application instructions will perform as stated in
its product literature. Because methods and conditions of use are beyond the control of Kryton, no
guarantee, expressed or implied can be given as to the results of application. Liability of Kryton shall be
limited to replacement of materials proved defective or, at its option, refund of the purchase price of the
product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Water Barrier for Repair of Concrete or Brick
1 of 2

Krystol Bari-Cote™
Water Barrier for Repair of Concrete or Brick

DESCRIPTION
Krystol Bari-Cote is a high-strength non shrink crystalline waterproofing grout that is uniquely designed to repair
leaking cracks, holes and joints. It is specially formulated with Kryton’s proven Krystol® technology which combines
chemically with water and concrete to form millions of needle-like crystals. These crystals grow in all directions to fill
any capillary pores of the grout and surrounding concrete to block the passage of water.

FEATURES
l High early strength
l Superior bonding ability
l Very high compressive strength
l Withstands hydrostatic pressure
l Contains no corrosive chemicals or metals
l Safe for contact with potable water
l Can be painted after curing
l Increased durability; reduces repair cost

KEY BENEFITS

l Fast and easy to use


l Waterproofs Permanently
l Increased durability decreases maintenance and repair costs
l Superior performance enhances your reputation for high quality work
l Contains Krystol® Technology

RECOMMENDED USES

Use as part of the Krystol® Crack Repair System to:


l Repair leaking cracks, construction joints and holes in concrete slab
l Waterproof form tie holes in concrete
l Repair spalled or honeycombed concrete

PHYSICAL PROPERTIES
Appearance Gray Powder
Bulk density g/cm3 (lb./cu.ft.) 1.40
pH (when mixed with water) 12

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Water Barrier for Repair of Concrete or Brick
2 of 2

PLASTIC PROPERTIES

Working time (20°C/68°F,50% RH) 15 minute


Hardening time(20°C/68°F,50% RH) 60 minute

HARDENED PROPERTIES
Hydrostatic head resistance 140m (460 ft.)
Compressive Strength (ASTM C109) 2 hours - 8MPa
1 day - 18.6 MPa
7 days - 40.2 MPa
28 days - 45.0 MPa
APPLICATION
1. Mix KrystolTM Bari-Cote to a suitable putty consistency (approximately 4 parts powder to 1 part clean water by
volume) and apply to the prepared surface using a trowel. Do not mix more than can be applied within 15 minutes.
2. For deep patches or overlay applications thicker than 13 mm (0.5 in.) mix KrystolTM Bari-Cote with clean 10 mm
(0.375 in.) pea gravel (approximately 4 parts powder to 1.5 parts gravel to 1 part clean water by volume).
3. For Construction Joints treatment mix to suitable putty consistency (4 parts powder to 1 part clean water by volume)
and apply as a second putty over Krystol T1TM.

For details on application methodology, please consult a Kryton representative for project specific recommendations

LIMITATIONS
Krystol Bari-Cote is effective for rigid structures only and is not intended for structures that experience variable loading
or repeated movement. Consult a Kryton representative for project specific recommendations.

SAFETY
For professional use only. This product becomes caustic when mixed with water or perspiration. Avoid contact with
skin or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious gloves.

PACKAGING
l 25 kg resealable pails

SHELF LIFE
KrystolTM Bari-Cote has a shelf life of 2 years for unopened pails, when stored under standard conditions and minimum
temperature of 7°C.

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. ( A Unit of Kryton, Canada), warrants that its products are free from manufacturer’s
defects and, when applied in accordance with the current specification application instructions will perform as so stated
in its product literature. Because methods and conditions of use are beyond the control of Kryton, no guarantee,
expressed or implied can be given as to the results of application. Liability of Kryton shall be limited to replacement of
materials proved defective or, at its option, refund of the purchase price of the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Mortar Protection Admixture (Above Grade)
1 of 2

Krystol Mortar Admixture (KMA) TM

DESCRIPTION
Krystol Mortar Admixture (KMA)TM is a hydrophillic crystalline admixture in dry powdered form which is specifically
formulated to provide long-term protection in rendering/plastering mortar, masonry mortar and concrete masonry units.
KMA can often be used in place of externally applied surface sealers to protect against water and waterborne
contaminants and can be easily incorporated into the existing mix design and application processes.

KMA contains Kryton’s unique and proven Krystol® technology which reacts with cement particles to form millions of
needle-like crystals, reducing both permeability and absorption of the mortar by filling the naturally occurring pores and
voids in cementitious mortar.

Krystol technology helps to simplify installation and provide superior performance such as its ability to self-seal minor
cracks and withstand water under pressure.

FEATURES
l Enhances durability resisting salt attacks, corrosion of embedded steel and water penetration
l Minimizes the chance of debonding
l Preserves aesthetics by resisting stains and discoloration caused by efflorescence, mold & mildew
and rust
l Enhances workability for ease of use, improves adhesion, reduces rebound loss and reduces cracking
l Has exceptional strength
l Self-seals minor cracking
l Withstands water under pressure such as wind-driven rain

RECOMMENDED USES
Use KMA to provide protection for:
l Rendering and plastering mortar over concrete masonry wall or other prepared substrates
l Masonry Mortar (i.e., mortar that goes between the masonry units)
l Concrete masonry units (i.e., blocks when they are manufactured)
l Backing Mortar for tile work in wet areas

PHYSICAL PROPERTIES
Appearance Gray Powder
3
Bulk density g/cm (lb./cu.ft.) 1.27
pH (when mixed with water) 12

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Mortar Protection Admixture (Above Grade)
2 of 2

APPLICATION
KMA is a dry powder that is added directly to the mortar during mixing. The dosage rate is 0.8 to 2% by wt of cement
(See Dosage). Mix to desired consistency. Most mixes will require less water than usual. Mix for at least 5 minutes after
adding to the mixer. Install mortar as normal. For increased damp-proofing performance apply mortar to a greater
thickness. Continue occasional mixing as the material is being installed. Discard any material that shows signs of
stiffening or setting. Do not wet-up by adding water.

CURING
Protection from rain until hardened. Protect from hot sun or wind for at least 24 hours. Cure the mortar application by
misting with water repeatedly for 2 or more days.

DOSAGE
l Dosage is 0.8 to 2% of Cementitious content
l 1 Kg per 50 Kg of Cement

SAFETY
For professional use only. This product becomes caustic when mixed with water or perspiration. Avoid contact with skin
or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious gloves. The safety precautions for
KMA treated mortar are the same as for regular mortar.

LIMITATIONS
KMA is an effective system for rigid structures only and may not resist water for mortar that experience variable loading
or repeated movement. Consult a Kryton representative for project specific recommendations.

PACKAGING
l 25 Kg resealable pails
l 1 kg pails

SHELF LIFE
KMA has a shelf life of 24 months for unopened pails when stored under standard conditions and minimum temperature
of 7OC.

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. ( A Unit of Kryton, Canada), warrants that its products are free from manufacturer’s
defects and, when applied in accordance with the current specification application instructions will perform as so stated
in its product literature. Because methods and conditions of use are beyond the control of Kryton, no guarantee,
expressed or implied can be given as to the results of application. Liability of Kryton shall be limited to replacement of
materials proved defective or, at its option, refund of the purchase price of the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Concrete Waterproofing Details
1 of 2

Krystol Plug™
DESCRIPTION
Krystol PlugTM is a fast setting powder that, when mixed to a stiff-dough consistency with water, may be used
immediately to arrest the seepage or flow of water through concrete voids. Kryton Plug is used to stop flowing water,
allowing waterproofing repair to be installed in leaking cracks, holes, joints or any place where water is flowing at a
high rate or under pressure.

FEATURES

l Stops flowing water immediately


l Sets fast, in one to two minutes
l Easy to mix add apply
l Will set up and harden under water
l Has exceptional strength
l Does not contain any Chlorides
l Safe for drinking water applications

KEY BENEFITS
Can stop extreme leaks (Water Under Pressure)

RECOMMENDED USES
l Use as part of the Krystol® Crack Repair System to repair leaking Cracks, Joints and Holes.
l Provides impervious, non-shrinking seal to prevent seepage around pipes and
metal fixtures in masonry and concrete.

PHYSICAL PROPERTIES

Appearance Dark Gray Powder


3
Bulk density g/cm (lb./cu.ft.) 1.4

pH (when mixed with water) 13

PLASTIC PROPERTIES
Working time (20°C/68°F,50% RH) 1 minute

Hardening time(20°C/68°F,50% RH) 2 minute

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Concrete Waterproofing Details
2 of 2

HARDENED PROPERTIES
Compressive Strength 50 Mpa (7250 psi) @ 7days

APPLICATION
To Waterproof Cracks, holes and Joints. Mix Krystol Plug to a suitable putty consistency that can be held in your
hand (wear gloves) approximately 4 parts powder to 1 part clean water by volume. Mix only the amount of material
that can be applied within one minute. After the Krystol Plug putty has been adequately kneaded into a uniform
texture, immediately press it firmly into the cracks and crevices to be sealed using maximum pressure without heavy
back & forth motion. Air and surface temperatures must be at least 4°C.
For detailed application methodology, please consult a Kryton representative for project specific recommendation.

LIMITATION
Krystol Plug is effective for rigid structures only and may not reliably seal structures that experience variable loading
or repeated movement. Consult a Kryton representative for project specific recommendations.

SAFETY
For professional use only. This product becomes caustic when mixed with water or perspiration. Avoid contact with
skin or eyes. Avoid breathing dust. Wear long sleeves, safety goggles and impervious gloves.

PACKAGING
l 5 Kg resealable pails

SHELF LIFE
Krystol Plug has a shelf life of 24 months for unopened pails, when stored under standard conditions & minimum
temperature of 7°C.

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. ( A Unit of Kryton, Canada), warrants that its products are free from manufacturer’s
defects and, when applied in accordance with the current specification application instructions will perform as so
stated in its product literature. Because methods and conditions of use are beyond the control of Kryton, no
guarantee, expressed or implied can be given as to the results of application. Liability of Kryton shall be limited to
replacement of materials proved defective or, at its option, refund of the purchase price of the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Waterproof Coating
1 of 2

Roof-Gardi
DESCRIPTION
Roof-Gardi is a Thermosetting Plastic Elastomer (TPE), synthetic based waterproof membrane. Because of its excellent
flexibility and thixotropic nature it is ideal for use on vertical as well as horizontal surfaces. An economical, easy to apply
and pollution free water proof coating Roof-Gardi works best on terraces, terrace gardens podiums etc. This coating is
provided in base white and can be pigmented to desired colour.

ADVANTAGES

l Increases life & durability of the structure


l Provides seamless and joint free seal throughout the surface that is impervious to water
l Lowers labour cost due to easy, simple and quick application
l Excellent bonding to most building materials
l UV resistant and can be used to protect sheet membranes
l Provides protective membrane for polyurethane foam insulation
l Provides anti-root resistance properties

AREAS OF APPLICATION

l Waterproofing of plaza and car park deck


l Waterproofing of external plastered walls creating a finished surface
l Waterproofing of new surfaces and repairs of old surfaces
l Waterproofing of roof slabs, terraces, balconies, sun shades, parapet walls etc.
l Waterproofing of flashing, roof edgings, gulleys, steeply pitched designs etc.
l Optimally suitable for application on structures having complicated geometry like domes, arches, shells, folded plates,
paraboloids, corrugated sheets etc.
l Provides increased protection when used as base or intermediate coat in Brick Bat Coba or IPS flooring

APPLICATION INSTRUCTIONS
l Substrate Preparation
Make sure the surface is free from oil, grease, loose particles, rust and contamination. For surface treated with asphalt
or bitumen coatings cut away any blisters and peel-off tracs and fill them properly. Masonry joints must be flush
jointed. In case of tiling roofs, terraces, balconies or sun shades, the joints between the tiles should be properly filled
to avoid water penetration through the joints.
0 0
l Substrate Temperature/ Ambient Temperature: should be +8 C minimum and +35 C maximum.
Note: Beware of Condensation. Surface temperature during application must be at least +30 C above dew point
l Application
For primer coat dilute Roof-Gardi with 25% water and apply with brush, spray or roller. Once dried, apply
perpendicular to each other, two coats of Roof-Gardi diluted with 5% water. Allowing the first coat to completely dry
before applying the second coat or make sure each coat is cured for 8 Hrs. at 300 C. All brushes and tools should be
cleaned with water immediately after use.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Waterproof Coating
2 of 2

COVERAGE

Coverage with 3 coats (inclusive of primer coat) will be approximately 750 gm/sq.m on a smooth surface.

SAFETY

Non-hazardous. If ingested, seek medical advice.

STORAGE

12 months for unopened pails. Store away from sunlight and preferably below 300 C

PACKAGING

20 kg resealable pail

PHYSICAL PROPERTIES

Appearance : White Thixotropic


Solid Content (by weight) : 65% Heated ± 2%
Specific Gravity : 1.32 ± 0.02
Thickness Coat : Approx. 1.0 mm, wet film
Tensile Strength : 440 PSI, ASTM D-412
Hardness Shore A : 60, ASTM D-2240
Permeability : 0.05 Perms inches
Temperature Limits 20 Mils : -290 C +930 C
Elongation : 440%

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. warrants that its products are free from manufacturer’s defects and, when
applied in accordance with the current specification application instructions will perform as so stated in its
product literature. Because methods and conditions of use are beyond the control of Kryton, no guarantee,
expressed or implied can be given as to the results of application. Liability of Kryton Buildmat Co. Pvt. Ltd.
shall be limited to replacement of materials proved defective or, at its option, refund of the purchase price of
the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Elastomeric Coating for walls
1 of 2

WALL-GARDi
DESCRIPTION
Weatherproof, elastomeric coating designed to protect and renew exterior stucco, concrete and masonry walls. Wall-
Gardi is a specially formulated pure acrylic with excellent elongation and recovery characteristics. Its high solids
content gives Wall-Gardi exceptional binding power as well as minimal shrinkage and bridges hairline cracks. Wall-
Gardi is waterproof but still breathes, giving long lasting protection that will not crack, blister or peel.

FEATURES

l Excellent elongation and recovery


l Excellent adhesion
l Can be applied over almost any surface
l Water based
l No fumes
l Bridges hairline cracks
l Excellent freeze thaw resistance
l Waterproof (passes 98 mph wind-driven rain test)
l Breathes to resist blistering and peeling
l Resists dirt pick-up
l U.V. Resistant/fade resistant
l Available in white colour but can be dyed to the colour of your choice

PACKAGING
• 20kg pail

INSTRUCTIONS
For professional use only. See material safety data sheet for this product.

APPLICATION
Apply using standard painting practices at the recommended range of coverage. The material should be used in its
original viscosity and should not be thinned. If thinning is necessary for spraying, use only clean water to a maximum of
5%. Apply evenly in two coats, allowing the first coat to completely dry before applying the second. When spraying very
coarse surfaces (such as rock-dash stucco) it is recommended that the material be “back-rolled” with a ¾ nap roller in
order to attain even coverage. Clean-up with mild soap and warm water.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in
TECHNICAL DATA SHEET
Elastomeric Coating for walls
2 of 2

PHYSICAL PROPERTIES
Percentage non – volatile (solids) By volume - 54%, By weight – 58%

Dry film thickness 2 coats @120sq.ft/gal each – 375 microns

Drying time (20 degree C, 50% R.H.) To Touch – 20 minutes, to Recoat after – 3 hours

Application temperature Minimum 10 degrees C

Service temperature - 30 to 60 Degree Celsius

Specific gravity 1.30

Colour White

Elongation recovery 96%

V.O.C. Content <2%

Viscosity 130KU

pH Value 9.0

Resistance to acids/alkalis Excellent

COVERAGE AND APPLICATION


l Dry film thickness of 375 microbes in two coats
l Apply @ rate 40-50 sqft./per coat
l Apply by brush, roller or airless spray
Spraying requires minimum 3000 psi airless sprayer capable of delivering 1 gallon/minute

SURFACE PREPARATION
Surface must be clean, dry and free from surface contamination including; dirt, grease, oil, dust, efflorescence, laitance
and organic growth. Surface must be free from any point or sealer that may prevent good adhesion. Peeling and
disintegrating coatings or water-repellent coatings must be removed. The surface must be sound. Remove any broken,
loose or rotted section. Cracks that are 1/32” (0.8 mm) or wider must be repaired prior to application. Prime all surfaces
with Surface Conditioner clear acrylic sealer.

SHELF LIFE
Minimum 12 months in unopened container, store away from sunlight and preferably below 30°C.

WARRANTY
Kryton Buildmat Co. Pvt. Ltd. warrants that its products are free from manufacturer’s defects and, when applied in
accordance with the current specification application instructions will perform as so stated in its product literature.
Because methods and conditions of use are beyond the control of Kryton, no guarantee, expressed or implied can be
given as to the results of application. Liability of Kryton Buildmat Co. Pvt. Ltd. shall be limited to replacement of materials
proved defective or, at its option, refund of the purchase price of the product.

Kryton Buildmat Co. Pvt. Ltd.


136-137 Centrum Plaza, Golf Course Road, Sector 53, Gurgaon, Haryana 122002 | Telefax: +91 124 4381140 / 41 |Email: info@kryton.in | Web: www.kryton.in

You might also like